ENGLISH OWNER’S MANUAL Dome Camera Please read this manual carefully before operating your set and retain it for future reference.
Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
1 Safety Information LG Electronics hereby declares that this/ these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC and 2011/65/EU. Safety Information Contact office for compliance of this product: Safety Precautions • Do not attempt to disassemble the camera To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service personnel for servicing.
Safety Information • Consumables Parts having contacts such as the lens-drive motors, cooling fan built inside the camera are subject to wear with time. About replacement and maintenance of such parts, please ask the nearest service center. Discuss the installation location for the camera with your retailer, and select a place that is strong enough for the installation. • Install the camera on a ceiling (concrete, etc.) at a location that is sufficiently strong to support it.
Contents Contents 19 Connecting power source 19 Protocol and baud rate settings 20 Camera ID Setting 23 Removing the Protection Tape 24 1 Safety Information 4 Safety Precautions 2 Preparation 24 Surface mount (optional) 25 Ceiling mount (optional) 27 Wall mount (optional) 29 Pendant mount (Optional) 4 Operation 33 Setup Menu Overview Menu navigation 8 Introduction 37 8 Features 37 9 Accessories 10 Part Names and Functions 3 Installation 12 Connections Mounting the
Contents 44 Auto Pan setting 44 Privacy Mask setting 45 Special setting 47 User title setting 47 ZOOM MAG setting 47 FUNCTION setting 48 DOME ID setting 48 LANGUAGE Setting 48 ALARM Setting 48 Alarm In setting 49 Alarm Out setting RESET Setting 49 Information 49 Initialization 49 Camera reset 49 Factory reset 5 Appendix 50 1 OSD Settings 47 49 7 Specifications 2 3 4 5
Preparation 2 Preparation 2 Preparation Introduction reproduced repeatedly. The Pan, Tilt and Zoom controls are available for pattern recording. ,,Note The dome cameras are designed for installation in an indoor or outdoor video surveillance system. The camera incorporates the digital signal processor, pan/ tilt mechanism, zoom lens and RS-485 communication interface in a compact outdoor enclosure.
Preparation • Controls by General Controller 9 For LCP2850-AN/AP This camera can be controlled by RS-485. Especially the camera has an excellent cost-saving effect because it can be controlled by the general RX point of contact signal. • Connects with the maximum 256 cameras This camera can be utilized after being connected with maximum 256 cameras. Therefore, it is capable of performing an excellent job in the large buildings or department stores.
Preparation Part Names and Functions a BNC connector cover cap b Video output BNC connector LCP2850I-AN/AP for Indoor a Supplies analog video signal (composite) to the connected device. c b 2 c Data Port A (RJ-45) RS-485 data communication and input data port for alarm (relay) signal. d d Data Port B (RJ-45) Output data port for alarm (relay) signal. Preparation e f e This port is not used. f This port is not used.
Preparation LCP2850-AN/AP for Outdoor a a BNC connector cover cap b Video output BNC connector Supplies analog video signal (composite) to the connected device. b c 11 c RS-485 Data Communication d Alarm In Data Terminal Input data terminal for alarm (relay) signal. d Output data terminal for alarm (relay) signal. f f Power input Terminal Connects to a AC 24 V power supply using proper cables.
Installation 3 Installation Connections 3 Precautions Installation • The following steps of installation and connection work should be done by qualified service personnel or system installers and should conform to all local codes. • Before you install and connect the camera, check and prepare the required peripheral devices and cables. • Before you connect the camera, turn off all devices to be connected, such as this camera and DVR. • Do not touch the dome cover’s window.
Installation Connecting Display device The video signal connection between the camera and the monitor. Display device connection 13 >>Caution Do not connect one alarm sensor to the several camera’s alarm input connector.
Installation PORT A Alarm input connection Description Color RS-485 + Red/White RS-485 - Black/White NC 3 ALARM IN COM Red ALARM IN 1 White ALARM IN 2 Light Green ALARM IN 3 Yellow Installation ALARM IN 4 A Alarm device B Alarm device C Alarm device D Pink E For LCP2850-AN/AP Alarm device 1. Connect the Adaptor cable to the Alarm In Data Terminal of the camera. 2. Connect the alarm device to the Adaptor cable.
Installation ALARM IN 3 White ALARM IN 4 Violet 15 ALARM output connections Connect the alarm device to the alarm output data port. Alarm signal output at an event occurrence. You can set the Alarm Output to the normal open or normal close mode. Alarm Input function This speed dome camera has a terminal that can sense the alarm signals. If the alarm sensor that has installed in a door, window, safe etc.
Installation E ALARM OUT [NO2] Green F ALARM OUT [COM2] Yellow G ALARM OUT [NC2] Blue H NC Brown For LCP2850-AN/AP 1. Connect the Adaptor cable to the Alarm Out Data Terminal of the camera. 2. Connect the alarm device to the Adaptor cable. When connecting lines, check and connect the color lines of the each device correctly. Refer to the below tables for color line information.
Installation RJ-45 Adaptor cable Alarm Out Data Terminal No Description Color A RS-485 + White B RS-485 - Orange Description Color ALARM OUT [NO1] White Blue ALARM OUT [COM1] Beige ALARM OUT [NC1] Black For LCP2850-AN/AP ALARM OUT [NO2] Brown 1. Connect the Adaptor cable to the RS-485 Data Communication of the camera. ALARM OUT [COM2] Red ALARM OUT [NC2] Orange 2. Connect the LKD1000 controller to the Adaptor cable.
A F G 18 Installation B H RJ-45 Adapter cable For LCP2850I-AN/AP PORT A RS-485 connection A For LCP2850-AN/AP RS-485 connection RS-485 RS-485 device A B RS-485device device RS-485 B C D E F G 3 TX- Installation H Adaptor cable RJ-45Adapter Adapter cable cable RJ-45 PORT PORT AA 1. Connect the RJ-45 adaptor cable to the PORT A (RJ-45) cable of the camera. 2. Connect the RS-485 device to the RJ-45 Adaptor cable.
Installation Connecting power source Connect a AC 24 V power source to the power input jack. (Recommended power adaptor is AC 24 V/2 A or above.) 19 Baud Rate setting ON ON OFF Protocol and baud rate settings The camera has one 8-bit DIP switch blocks that determine the protocol and baud rate of the data communication. Settings are loaded when the camera boots up. Be sure to turn the camera off, change the DIP switch settings, and then power the camera back up to load the changes.
Installation Camera ID Setting 28 The camera’s ID is set to “0” as factory default. If you use two or more cameras simultaneously, change the ID of the cameras. Set the camera ID setting referring to the pictures and the table on the below.
Installation 67 ON 68 69 ON ON OFF 106 OFF ON OFF ON OFF ON ON OFF OFF OFF ON OFF OFF OFF ON OFF ON OFF ON OFF OFF OFF ON OFF 107 ON ON OFF ON OFF ON ON OFF 108 OFF OFF ON ON OFF ON ON OFF 70 OFF ON ON OFF OFF OFF ON OFF 71 ON ON ON OFF OFF OFF ON OFF 109 ON OFF ON ON OFF ON ON OFF 110 OFF ON ON ON OFF ON ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 111 ON ON ON ON OFF ON ON OFF 112
3 Installation Installation 145 ON OFF OFF OFF ON OFF OFF ON 184 OFF OFF OFF ON ON ON OFF ON 146 OFF ON OFF OFF ON OFF OFF ON 147 ON ON OFF OFF ON OFF OFF ON 185 ON OFF OFF ON ON ON OFF ON 186 OFF ON OFF ON ON ON OFF ON 148 OFF OFF ON OFF ON OFF OFF ON 149 ON OFF ON OFF ON OFF OFF ON 187 ON ON OFF ON ON ON OFF ON 188 OFF OFF ON ON ON ON OFF ON 150 OFF ON ON OFF ON OFF OFF ON 151 ON ON ON OFF ON OFF OFF ON 189
Installation 223 ON ON OFF ON ON Removing the Protection Tape 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON You should remove the protection tape before installing the camera. Remove the protection tape carefully. 227 ON ON OFF OFF OFF ON ON ON For LCP2850-AN/AP models. 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 1. Loosen the screws using the wrench and remove the dome cover.
Installation Mounting the camera 2. Install the surface mounting bracket on the ceiling. You can mount the camera on the ceiling or wall. Surface mount (optional) Follow the instructions below to surface mount the camera. >>Caution The building structure must be able to support 8 kg. 3 Installation 1. Use the installation guide template to check the mounting location. Face the front of the label toward the area of interest. 3.
Installation 25 Ceiling mount (optional) 4. Tighten the locking screw. Follow the instructions below to mount the camera on the ceiling. >>Caution The building structure must be able to support 8 kg. 1. Make a hole through the ceiling as shown below. Ø 166 mm 3 Ø 166 mm 2. Fasten the safety cable to the building superstructure. The building superstructure can vary depending on your installation environment. Installation 5. Connect the cables to the cable jacks of the camera body.
Installation 3. Install the ceiling mounting bracket on the ceiling. Face the front of the ceiling mounting bracket toward the area of interest. 5. Pass the connection cable through the inner side of the ceiling. Connect the cables to the cable jacks of the camera body. Ø 166 mm 3 Installation 4. Tighten the screws until the ceiling mounting bracket holds the ceiling firmly. 6. Assemble the camera and ceiling mounting bracket by following step a and b.
Installation 7. Tighten the locking screw. 27 Wall mount (optional) Install the camera by the following order. 1. Disassemble the PIPE Installation Bracket to remove the [A] part. [A] >>Caution Do not expose the connected part of the camera cable jacks in the rain or moisture. Check the red stripe on one side of the safety cable. 2. Install the PIPE Installation Bracket to the Wall Mount assembly. 3 Installation 8. Connect the cables to the cable jacks of the cam era body.
Installation 3. Drill a hole on the wall where you want to install the pipe. Pass the connection cable through the wall mount assembly so that they hang down. 3 6. Attach the camera to the camera assembly bracket by following step a and b. Align the locking point of the wall mount assembly and the camera. 4. Install the wall mount assembly. Installation 7. Tighten the locking screw. 5. Connect the connection cable and the safety cable to the camera body.
Installation 8. Assemble the camera cover as shown below. 29 Pendant mount (Optional) Install the camera by the following order. 1. Disassemble the PIPE Installation Bracket to remove the [A] part. [A] ,,Note You can install the PIPE Installation Bracket direct to the other type LG Wall Mount assembly. This LG Wall Mount assembly make to easy to install your camera. 3 Installation 2. Install the PIPE Installation Bracket to the Pendant Mount assembly.
Installation 3. Drill a hole on the wall where you want to install the pipe. Pass the connection cable through the pendant mount assembly so that they hang down. 4. Install the pendant mount assembly. 3 Installation 5. Connect the connection cable and the safety cable to the camera body.
Installation 6. Attach the camera to the camera assembly bracket by following step a and b. Align the locking point of the wall mount assembly and the camera. 31 7. Tighten the locking screw.
Installation 8. Assemble the camera cover as shown below. ,,Note You can install the PIPE Installation Bracket direct to the other type LG Wall Mount assembly. This LG Wall Mount assembly make to easy to install your camera.
Operation 33 4 Operation Setup Menu Overview The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus. 1st level 2nd level 3rd level Contents CAMERA SET FOCUS FOCUS MODE AUTO/MANUAL/ONE PUSH/ZOOM TRIG FOCUS DIST 1 M, 3 M, 6 M ZOOM START x1 to x27 ZOOM END x2 to x336 RETURN - IRIS AUTO/MANUAL AGC OFF, 1 to 10 WDR/BLC OFF/WDR/BLC/HSBLC BRIGHTNESS 0 to 100 SHUTTER OFF, A.
Operation CAMERA SET DAY/NIGHT 3D-DNR COLOR 4 AUTO D/N LEVEL LOW/MIDDLE/HIGH DWELL TIME 5,10,15,30,60 SEC RETURN - DAY - NIGHT - OFF - LOW - MIDDLE - HIGH - ON COLOR OFF - SHARPNESS 0 to 68 - STABILIZER ON - OFF - Operation RETURN PAN/TILT SET -50 to 50 PRESET SET PRESET NAME OFF/ON SPEED 1 to 127 DWELL TIME 1 to 255 IRIS AUTO, 20, 40, 60, 80, 100 % WDR/BLC/HSBLC OFF/ LOW WDR/ MID. WDR HIGH WDR/ LOW BLC/ MID. BLC / HIGH BLC/ LOW HSBLC / MID.
Operation PAN/TILT SET GROUP TOUR PATTERN AUTO PAN PRIVACY MASK 1 to 10 RUN 1 to 10 CLEAR 1 to 10 RETURN - RECORD 1 to 4 RUN 1 to 4 RETURN - SET AUTO PAN 1 to 8 RUN - CLEAR - RETURN - MASK NUMBER 1 to 8 SET MASK - MASK STATE ON/OFF MASK COLOR GRAY, WHITE, BLACK WIDTH 0 to 320 HEIGHT 0 to 240 RETURN - PROPORTIONAL PT ON/OFF COMPASS ON/OFF HOME POSITION ON 4 Operation SPECIAL SET GROUP SET GO DWELL TIME (INFINITE to 100 MIN) RETURN AUTO RETURN OFF - ON RE
Operation PAN/TILT SET SPECIAL COMMUNICATION PROTOCOL LG MULTIX/ PELCO C/ PELCO D/ PELCO P BAUDRATE 2 400/ 4 800/ 19 200/ 38 400/ 9 600 BPS SAVE & EXIT - RETURN OSD SET - USER TITLE ON/OFF - ZOOM MAG ON/OFF - FUNCTION ON/OFF - DOME ID ON/OFF - RETURN - LANGUAGE NORMAL OPEN/CLOSE ALARM IN1 to ALARM IN4 PRESET 0 to 255 4 DWELL TIME 3 to 255 Operation ALARM SET The option depends on the model.
Operation Please Enter Camera ID Target CAM ID : _ Menu navigation 2. Enter the connected camera ID to control the camera connected to the LKD1000 controller directly and then press ENTER. The camera control menu will be displayed. We use the LKD1000 controller in this manual to explain the features of the LG Dome camera because of the LKD1000’s ability to control all of the LG Dome camera’s advanced features. (For detailed controller instructions, refer to the LKD1000 Controller Manual.
Operation Camera menu settings Focus setting The camera adjusts the focus automatically by sensing the center of the picture. Focus Distance setting Selects the minimum shooting distance for the focus. Select [FOCUS DIST] option on the [FOCUS] menu, then select a focus distance value. Zoom Start setting You can set the zoom start position of the camera. When the zoom function is operated, the zoom always will start at the selected zoom start position.
Operation • AUTO: The lens iris is set automatically. • MANUAL: Use [Near] or [Far] button to select the DC Iris level. DC Iris level are set by one parameter unit. SHUTTER (Shutter Speed) setting Select the desired shutter speed for camera exposure. You can change the shutter speed to higher speed to capture fast-moving subjects, though the image becomes darker. AGC (Automatic Gain Control) setting 1. Select [SHUTTER] option on the [EXPOSURE] menu.
Operation • • -- When the scene mostly contains high color temperature objects, such as a blue sky or sunset. -- When the scene is dim. When the color temperature is out of the 3 500 K to 6 500 K range. -- When the scene mostly contains high color temperature objects, such as a blue sky or sun set. -- When the scene is dim. MANUAL: You can set the white balance options manually. -- 4 Operation • -- DWELL TIME: Use [Near] or [Far] button to select a dwell time.
Operation Color setting Stabilizer setting You can switch the displayed picture to grayscale or color. The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration. This function is useful for outdoor surveillance. 1. Select [COLOR] option on the [CAMERA SET] menu. 2. Use [Near] or [Far] button to change a color effect. • ON: To display the picture with color. Select ON and press [Open] or [Close] to display the submenu.
Operation To register preset positions 1. Select the [SET PRESET] option on the [PRESET] menu. 2. Use the [Near] or [Far] button to select the preset number you wish to register and press the [Open] or [Close] button. 3. Set the preset name. How to set the preset name. 1. Set the NAME option to [ON] and press [Open] or [Close] button. 2. Use [In], [Out], [Near] or [Far] button to select a character, number, symbol mark or option item. 4 • : Moves cursor to left or right.
Operation Group tour setting To delete a group You can create a group using preset positions that are registered already. A maximum of 10 groups is available. 1. Select [CLEAR] option on the [GROUP TOUR] menu. 43 You can delete a memorized group. 2. Select the group number and press [Open] or [Close] button. The group will be deleted. Pattern setting You can activate the camera in a repeating pattern. The pattern is programmed by recording your manual pan, tilt, and zoom operations.
Operation To play the pattern 8. Repeat steps 1 to 7 to add additional positions. 1. Select [RUN] option on the [PATTERN] menu. 9. Select [RETURN] option and press [Open] or [Close] button to exit the setting menu. 2. Select the recording number and then press [Open] or [Close] button to play the programmed pattern. The tour will play indefinitely until you stop it by moving the joystick or pressing any button. Auto Pan setting By selecting the Auto Pan number, the camera pans automatically.
Operation 1. Select [PRIVACY MASK] option on the [PAN/TILT MENU]. 2. Press [Open] or [Close] button to display the PRIVACY MASK MENU. 45 Special setting 3. Use [Near] or [Far] button to select a zone number on the [MASK NUMBER] option. 4. Select the [SET MASK] option and press [Open] or [Close] button. 5. Select the mask zone using the joystick and then press [Open] or [Close] button to save it. 6. Use [Near] or [Far] button to set up the [ON] or [OFF] on the [MASK STATE] option.
Operation Home position The home position is the camera’s basic position. The camera returns to this position whenever you want. Use the following procedure to make the home position. 1. Select [HOME POSITION] option on the [SPECIAL] menu. 2. Use [Near] or [Far] button to set it ON. 3. Press [Open] or [Close] button. 4. Select [SET] option and then press [Open] or [Close] button. ,,Note The top side of screen may be hidden by tilting range.
Operation OSD Settings • CLR: If you enter the wrong code, select [CLR] then press [Open] or [Close]. All letters will be erased at once. • POS: Move the USER TITLE position on the screen using the [Near] or [Far] buttons. • END: Select this option to exit the settings. 47 ZOOM MAG setting Displays or removes the zoom OSD on the screen. . 1. Select [ZOOM MAG] option on the [OSD] menu. 3. Select [RETURN] option and press [Open] or [Close] button to exit the setting menu.
Operation DOME ID setting Displays or removes the Camera ID OSD on the screen. ALARM Setting This camera has a terminal that can sense the alarm signals. The camera can be programmed to go to a preset with a signal from any connected alarm device. 1. Select [DOME ID] option on the [OSD] menu. 2. Use [Near] or [Far] button to set it [ON] or [OFF] 3. Select [RETURN] option and press [Open] or [Close] button to exit the setting menu.
Operation Alarm Out setting Initialization 1. Select one of the alarm out options on the [ALARM SET] menu. You can initialize the camera settings. 2. Use [Near] or [Far] button to set it [ON]. 2. Press [Open] or [Close] button then confirmation window is displayed. 3. Press [Open] or [Close] button. 4. Select alarm input number or motion detection. When the selected alarm input is triggered or motion is detected, the alarm signal is outputted. 5.
Appendix 5 Appendix Specifications Model LCP2850-AN LCP2850-AP LCP2850I-AN LCP2850I-AP Signal System NTSC PAL NTSC PAL Image Sensor 4.5 mm(1/4 Type) Super HAD II CCD Total Pixels Number 520 000 Pixels 610 000 Pixels 520 000 Pixels 610 000 Pixels Effective Pixels Number 490 000 Pixels 570 000 Pixels 490 000 Pixels 570 000 Pixels Horizontal Resolution 600 TV Lines Lens x28 Zoom, F1.5 (Wide End), F3.7(Tele End), f= 3.
Appendix Model LCP2850-AN LCP2850-AP LCP2850I-AN Video Output 1 Vp-p Composite ( 75 Ω) Backlight Compensation WDR / BLC / HSBLC / OFF Electric Shutter 1/60 to 1/120 000 1/50 to 1/120 000 LCP2850I-AP 1/60 to 1/120 000 OFF / LOW / MIDDLE / HIGH Auto Gain Control ON / OFF Digital Effect Auto Flip Pattern Recording & Play 1 to 4 / 1 to 4 Protection Vandal Proof / IP66 Sens-Up OFF / AUTO / MANUAL Iris Control AUTO/MANUAL Stabilizer (EIS) ON / OFF Motion Detection Support Panning Ra
