ENGLISH OWNER’S MANUAL Dome Camera Please read this manual carefully before operating your set and retain it for future reference. MODEL LCP2840-DN/DP LCP2840I-DN/DP 1504 (V7.
CAUTION Warning RISK OF ELECTRIC SHOCK DO NOT OPEN • Do not install this equipment in a confined space such as a bookcase or similar unit. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. • Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70. • This is a class A product.
Contents Introduction.....................................................................5 About Dome Camera...............................................................5 Features.........................................................................................5 Safety Precautions.....................................................................6 Identification of Camera..........................................................7 Installation......................................................
About Dome Camera The dome cameras are designed for installation in an indoor or outdoor video surveillance system. The camera incorporates the digital signal processor, pan/tilt mechanism, x28 zoom lens and RS-485 communication interface in a compact outdoor enclosure. Features mm High Sensitivity Support The camera provides the high quality picture with 4.5 mm (1/4 Type) Super HAD II CCD. mm Preset Position Preset position is the function to register camera monitoring positions (preset positions).
mm Day & Night Function This camera can be selected Color or Black & White. You can set Color in the daytime and Black & White at night due to the low illumination. (Filter Conversion type) mm DSS (Digital Slow Shutter) function It is possible to highly sensitive surveillance because of DSS(Digital Slow Shutter) function. mm WDR (Wide Dynamic Range) function The camera can be best condition to watch easily inside or outside in the strong back light.
Identification of Camera Introduction LCP2840-DN/LCP2840-DP d e f “A” g a Camera mounting bracket b Dome camera body c Dome cover assembly d Video output cable with BNC connector Connects with the video connector of the monitor. e Power cable (DC 12 V) f Data Communication Terminal - RS-485 g Data Communication Terminal - Alarm Input h Fall Prevention Wire Be sure to hook the fall prevention wire into a bracket.
LCP2840I-DN/LCP2840I-DP d e f “A” g a Camera mounting bracket (Optional) b Dome camera body c Dome cover assembly d Video output cable with BNC connector Connects with the video connector of the monitor. e Power cable (DC 12 V) f Data Communication Terminal - RS-485 g Data Communication Terminal - Alarm Input h Fall Prevention Wire Be sure to hook the fall prevention wire into a bracket. Caution: When you fix the dome cover to the dome camera body, you must insert the wire in the dome camera body.
Installation Installation Precautions The following steps of installation and connection work should be done by qualified service personnel or system installers and should conform to all local codes. Before you connect the camera, turn off all devices to be connected, such as this camera and DVR. Note: Do not touch the dome cover’s window. Camera Installation Location Discuss the installation location for the camera with your retailer, and select a place that is strong enough for the installation.
Mounting the Camera Surface mount The figures show an example of the camera mounted on a ceiling or wall with a locally procured bracket. LCP2840-DN/LCP2840-DP Note: The camera have not been evaluated for wall or ceiling mounting.
Note: When you install the camera to the ceiling mount, you must drill a hole in the camera body as shown right. (ø 5.0) Pendant mount (Optional) Install pipe and camera as shown below.
(A) Wall mount (Optional) How to install Install the camera in the following order. 1. Drill holes on the wall where you want to install the pipe. 2. Install the pipe and camera as shown below. “A” Pipe threads should be clean and rust free. Use a sealer (such as Teflon™ tape and silicone sealer) on the threads. Add thread sealing tape Note: The pipes and brackets for mounting are not supplied. Reference: Specifications of LG Standard pipe.
Dipswitch Setting The camera has one 4 bit switches that determine the protocol and baud rate of the data communication. Settings are loaded when the camera boots up. Be sure to turn the camera off, change the dipswitch settings, then power back up to load the changes. 1. Turn off the camera. 2. Remove the dome cover from the housing. 3. Set the dipswitches inside the housing as per the table below.
Switch position (SW104) Baud Rate (OFF OFF OFF OFF) 9 600 BPS (OFF OFF OFF ON) 1 200 BPS (OFF OFF ON OFF) 2 400 BPS (OFF OFF ON ON) 4 800 BPS (OFF ON OFF OFF) 19 200 BPS (OFF ON OFF ON) 38 400 BPS (OFF ON ON OFF) 57 600 BPS (OFF ON ON ON) 115 200 BPS Camera ID Setting If you want to use multiple cameras, you should set camera IDs differently by using the 8-bit Dip switch for each camera. Set the camera ID setting referring to the pictures and the table on the below.
ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF O
195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 16 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF
Connections Model LCP2840-DN/DP is used for the description, operation and details provided in this operating guide. Precautions • • The connections should be made by qualified service personnel or system installers in accordance with all local codes. DC 12 V can be used. RS-485 connection Use the cable that is described below for RS-485 site communication. • Shielded, twisted pair cable • Low impedance • Wire gauge size is thicker than AWG #22 (0.33 mm²).
ALARM IN connections Connection of the data terminal and adaptor for alarm input Connect external sensors to the 8-pin haness connector. Each alarm sensor should be connected with G (GND). Input specifications are low-active, non-voltage contact (ON when active) or open collector (Low when active). No 1 2 3 4 5 Cautions • Alarm input connection must be connected to only one port of two communication ports. • Do not connect one alarm sensor to the several camera’s alarm input connector.
Before inputting the alarm signal Before inputting the alarm signal Alarm signal input Alarm signal input Alarm 4 Preset 1 Alarm 4 Preset 3 Preset 1 Preset 2 Alarm 3 Alarm 3 Manual mode Function status Auto mode While observe a specific position. Change the observe position to the alarmed position then keep observe the alarmed position and you cannot control the camera.
Connecting LKD1000 controller System Connection Connecting the LKD1000 controller to control the camera. (Refer to the manuals of the LKD1000 controller for more details.). Note: Data Port When any peripheral is turned off and turned on again, the camera is also turned off and turned back on. Caution: Adaptor Do not connect the alarm connectors to the another camera’s alarm connectors.
Operation Setup Menu Overview Main Menu DAY / NIGHT FOCUS Sub Menu Contents FOCUS MODE FOCUS DIST ZOOM START ZOOM END ZOOM SPEED ZTRK MODE AUTO / ONE PUSH / ZOOM TRIG / MANUAL 50 cm,1 m, 3 m, 5 m x1 to x27 x2 to x336 SLOW / MIDDLE / QUICK AUTO / MANUAL / AUTO ONLY INITIAL SET RET / TOP / END AUTO / MANUAL 0 to 10 OFF / WDR / BLC / HSBLC 0 to 100 X512, ... , x2, AUTO, OFF, A.FLK, 1/160, ...
Main Menu Sub Menu Contents CAMERA ID D-EFFECT 0 to 255 Not supported. OFF COLOR LEVEL ON EXIT RET / TOP / END OFF / ON 0 to 68 OFF / ON OFF USER TITLE OFF / ON ZOOM MAG OFF / ON ON FUNCTION OFF / ON CAMERA ID OFF / ON EXIT RET / TOP / END ENG (The supported language can be different depending on the model.
General Operation Accessing setup menus To access the setup menus using the keys on a LKD1000 controller, do the following: 1. Select CAM (Camera) icon in the main menu and then press ENTER. The camera ID input menu will be displayed. CAM CAM Please Enter Camera ID Please Camera Target Enter CAM ID : _ ID Target CAM ID : _ 2. Enter the connected camera ID to control the camera connected to the LKD1000 controller directly and then press ENTER. The camera control menu will be displayed.
Focus Distance setting Zoom Speed setting Selects the minimum shooting distance for the focus. Selects a zoom speed. Select [FOCUS DIST] option on the [FOCUS] menu, then select a focus distance value. Select [ZOOM SPEED] option on the [FOCUS] menu, then select a zoom speed. Zoom Start setting Zoom Tracking Mode setting You can set the zoom start position of the camera. When the zoom function is operated, the zoom always will start at the selected zoom start position. Selects a zoom tracking mode.
Exposure settings area of picture. The HSBLC mode is automatically activated only in low illuminance scene. Iris setting Select the desired lens iris value for camera exposure. Select [IRIS] option on the [EXPOSURE] menu, then select a value. • AUTO: The lens iris is set automatically. • MANUAL: Use [Near] or [Far] button to select the DC Iris level. AGC (Automatic Gain Control) setting If the images are too dark, change the maximum [AGC] value to make the images lighter. 1.
SHUTTER (Shutter Speed) setting White Balance setting Select the desired shutter speed for camera exposure. You can change the shutter speed to higher speed to capture fast-moving subjects, though the image becomes darker. Select the method by which the camera shifts its output colors to compensate for the color of a light source. 1. Select [SHUTTER] option on the [EXPOSURE] menu. 2. Use [Near] or [Far] button to set shutter speed. SENS-UP setting 1.
>> INDOOR: The color temperature range for the proper white balance is approximately 3 200 K. >> OUTDOOR: The color temperature range for the proper white balance is approximately 5 100 K. -- RED: Set the desired red value. -- BLUE: Set the desired blue value. Day/Night setting Motion Detection setting The motion detection detects the moving objects in the scene by monitoring changes in brightness level. You can select the level of sensitivity for motion detection to 4 zone. 1.
Privacy Mask setting 3D-DNR setting This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in the screen. Up to 8 zones can be registered. 1. Select [PRIVACY MASK] option on the [CAMERA SET] menu. 2. Use [Near] or [Far] button to select a [ON] and press [Open] or [Close]. The PRIVACY MASK menu appears. 1. Select [3D-DNR] option. If pictures are not clear due to brightness, use for reduce the noise of picture. 2.
D-EFFECT (Digital effect) setting value, the image outline becomes dim. This model support D-EFFECT function by Auto Flip. Stabilizer setting Color setting You can switch the displayed picture to grayscale or color. 1. Select [COLOR] option on the [SPECIAL] menu. The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration. This function is useful for outdoor surveillance. 2. Use [Near] or [Far] button to change a color effect.
User title setting Language setting You can use the camera identification to assign a number and character to the camera. The USER TITLE is displayed on the upper left of the screen. To disappear the user title, select [OFF]. Select a language for setup menu and information display. 1. Select [USER TITLE] option on the [OSD] menu. 2. Use [Near] or [Far] button to select a [ON] then press [Open] or [Close]. The USER TITLE menu appears. A 3.
Reference Specifications LCP2840-DN MODEL LCP2840I-DN LCP2840-DP NTSC Signal System LCP2840I-DP PAL 4.5 mm (1/4 Type) Super HAD II CCD Image Sensor XDI-II ISP Total Pixels Number 520 000 Pixels 610 000 Pixels Effective Pixels Number 480 000 Pixels 570 000 Pixels Sync System Internal Lens x 28 Zoom, F1.5 (Wide End) , F3.7 (Tele End), f=3.5 mm to 98 mm Horizontal Resolution 600 TV Lines S/N Ratio 50 dB (AGC Off ) Minimum Illumination (30IRE) Color 0.01 lx (Sens-up OFF), 0.
MODEL LCP2840-DN LCP2840-DP Digital Effect Auto Filp Preset/ID 128 Position / 256 Auto Panning 2 to 8 points Pattern 1 Pattern Recording & Play 1 Group Tour Maximum 9 Groups Operation Temperature -20 °C to 50 °C -10 °C to 50 °C -20 °C to 50 °C Safekeeping Temperature -30 °C to 60 °C Operation Humidity 0 % RH to 80 % RH Safekeeping Humidity 0 % RH to 90 % RH Power Supply DC 12 V Power Consumption 12 W Weight 10 W 12 W LCP2840I-DP -10 °C to 50 °C 10 W 174 mm x 167.
