L2104-DN / L2104-DP
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• Caution: Danger of explosion if battery is incorrectly re placed. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. • Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings. Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.
Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4.
Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accord ance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Cautions for Safe Operation Power Supply • This camera must always be operated at DC 12V Certified/Listed, class 2 power supply only. Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides. They may damage the surface nish and/or impair the oper ation of the camera. Operating and storage location Handling of the unit Be careful not to spill water or other liquids on the unit. Be cautions not to get combustible or metallic material inside the body.
Contents Features .......................................................................................... 8 Part Names and Functions ................................................ 9 Connections ................................................................................ 10 Installation ................................................................................... 11 Installing the camera on a ceiling or wall ......................... 11 Adjustment ..............................................
Featur es This Color Video Camera is designed for installation in an indoor video surveillance system. This manual contains instructions on how to install and manage the Color Video Camera in your video surveillance system. Should you require any technical assistance, please contact authorized service center. • 1/3" SUPER HAD COLOR CCD II • Resolution: 540TV Lines Accessories DOME CAMERA VIDE O OUTPUT TE S T C ABLE • DAY/NIGHT Automatically change • 3.6mm Fixed Focus lens (F2.0) • Min. illumination 0.
Part Names and Functions 12.
Monitor(or 10 )
Installation Installing the camer a on a ceiling or wall 1. To install it, please take off the lens protection tape after opening the dome cover. 2. Secure the camera mounting bracket to the position where the camera should be mounted with the supplied screws. (Please leave a good position of cable not to interrupt the surveillance area with it when installing.) Lens Protection Tape Tapping Type(Supplied) 3.
Installation ③ . Adjust the camera lens to face the area to be monitored and x the main body and the dome cover by aligning the grooves and rotating the body clockwise.
Installation Adjustment Service Video connector Connect a portable monitor to the video jack.
Lens Focus Adjustment • The lens is focused far from 1M when ex-factory. Therefore we recommend the lens focus as is.
Menu Operation This camera utilizes an on-screen user MENU. To set items on the menu, use the following switch. UP Used to move upper direction on the menu screen. Use this button to select an item or adjust the parameters. DOWN Used to move lower direction on the menu screen. Use this button to select an item or adjust the parameters. RIGHT :SET Moves the cursor to the right. Used to increment the value selected in the menu. The parameter changes each time this button is pressed.
Menu Operation OSD Menu Overview Main Menu The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus.
Menu O peration Main M enu DAY&NIGHT Sub M enu COLOR B&W OFF Contents ON Sub M enu OFF MONITOR SET WINDOW ALL SET ALL CLEAR SENSITIVITY TRACE HOLD TIME ON/OFF GAMMA 0~200 OFF ICON TRACE 1~15 SPECIAL ON MASK NUMBER DISPLAY COLOR ON HEIGHT WIDTH MOVE Y MOVE X 1~4 ON/OFF GRAY BLACK WHITE 1~99 1~99 1~99 1~99 MIRROR USER TITLE DPC SET OFF PRIVACY Contents SHARPNESS ALARM MOTION DET Main M enu LANGUAGE RESET 1~49 CRT LCD USER 0.45 0.
Menu Operation OSD MENU OSD(SCREEN CONTROL)-SETTING CAMERA SETTING EXPOSURE WHITE BAL DAY & NIGHT MOTION DET PRIVACY SPECIAL RESET EXIT ELC ATW AUTO OFF OFF 1.Press OSD key down at inside of Dome base. The setup menu screen appears on the monitor. 2.Press OSD key to upside or downside to select an option then Press OSD key down. Submenu appears on the monitor. 3.Press OSD key to upside or downside to select a Submenu option. 4.Use OSD key to left or right to select a value. 5.
Menu Operation OSD MENU-Exposure Settings OSD MENU-Exposure Settings(BLC / LSC) You can set the exposure options using the EXPOSURE menu. Use WIDE BLC option to view the object clearly in strong CAMERA SETTING EXPOSURE WHITE BAL DAY & NIGHT MOTION DET PRIVACY SPECIAL RESET EXIT ELC ATW AUTO OFF OFF backlight conditions. EXPOSURE-ELC BLC/LSC BRIGHTNESS AGC SHUTTER EXIT BLC 45 MIDDLE AUTO RET 1.Select [WIDE BLC]] option. 2.Use OSD key to left or right to select a mode then press[SET].
Menu Operation BLC : Use for adjusting brightness of the subject to view the object clearly in backlight condition. Set to select [on] or [off] HSBLC : Use for masking brightness of the specific area to view the subject more clearly. The HSBLC mode is automatically activated only in low illumination scene. Push OSD key to left or right to select a ON or OFF. Press[SET] to exit the Area setting menu. -ON: It has powerful back light compensation performance.
Menu Operation OSD MENU-White Balance settings You can select one of three modes for white balance adjustment. CAMERA SETTING EXPOSURE WHITE BAL DAY & NIGHT MOTION DET PRIVACY SPECIAL RESET EXIT ELC AWB AUTO OFF OFF WHITE BAL-MANUAL R-Y GAIN B-Y GAIN EXIT 128 128 END WHITE BAL-MANUAL MANUAL R MANUAR B EXIT 1.Select [WHITE BAL] option. 2.Use OSD key to left or right to select a mode thenpress [SET].
Menu Operation OSD MENU-Day/Night Setting CAMERA SETTING EXPOSURE WHITE BAL DAY & NIGHT MOTION DET PRIVACY SPECIAL RESET EXIT ELC ATW AUTO OFF OFF DAY & NIGHT-AUTO BURST DAY>NIGHT NIGHT>DAY DELAY TIME EXIT ON 120 90 5 RET 1.Select [DAY/NIGHT]option. 2.Use OSD key to left or right to select mode for day/night function. -AUTO : You will be able to change the Day/Night mode automatically.
Menu Operation OSD MENU-MOTION DETECTION Setting [MOTION DET] detects the moving objects in the scene by monitoring changes in brightness level. Select the level of sensitivity for motion detection to 4 zone. CAMERA SETTING EXPOSURE WHITE BAL DAY & NIGHT MOTION DET PRIVACY SPECIAL RESET EXIT ELC ATW AUTO OFF OFF MOTION DET ALARM SET WINDOW ALL SET ALL CLEAR SENSITIVITY TRACE HOLD TIME EXIT OFF 200 ICON 5 RET 1. Select[MOTION DET]option. SET WINDOW : Use OSD key to left or right to select some 2.
Menu Operation OSD MENU-MOTION DETECTION Setting CAMERA SETTING EXPOSURE WHITE BAL DAY & NIGHT MOTION DET PRIVACY SPECIAL RESET EXIT ELC ATW AUTO OFF OFF MOTION DET ALARM SET WINDOW ALL SET ALL CLEAR SENSITIVITY TRACE HOLD TIME EXIT OFF 200 ICON 5 RET ALL SET : it's to select all windows. TRACE : [ICON]↔[TRACE]↔[OFF] ALL CLEAR : it's to clear all windows. -ICON : it appears a icon when set some areas and set [ICON]. left or right and push the KEY down one second or more.
Menu Operation OSD MENU-Privacy Setting This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in the screen. Up to 4 zones can be registered. CAMERA SETTING EXPOSURE WHITE BAL DAY & NIGHT MOTION DET PRIVACY SPECIAL RESET EXIT ELC ATW AUTO OFF OFF 1. Select PRIVACY [ON] and the menu appears. 2. Select [MASK NUMBER] one of 1, 2, 3, 4 This number starts from the left top area with clockwise. 3.
Menu Operation OSD MENU-Special Menu Settings This menu lets you adjust and set up SHARPNESS, GAMMA, MIRROR, USER TITLE, DPC SET, LANGUAGE function by yourself in the SPECIAL menu. CAMERA SETTING EXPOSURE WHITE BAL DAY & NIGHT MOTION DET PRIVACY SPECIAL RESET EXIT ELC ATW AUTO OFF OFF SPECIAL SHARPNESS MONITOR GAMMA MIRROR USER TITLE DPC SET LANGUAGE EXIT 1. Select [SPECIAL] option. 2. Press OSD key down and the SPECIAL menu appears. Setting SHARPNESS You can select SHARPNESS level.
Menu Operation OSD MENU-Special Menu Settings (Setting the USER TITLE) SPECIAL SHARPNESS MONITOR GAMMA MIRROR USER TITLE DPC SET LANGUAGE EXIT USER TITLE 15 LCD 0.45 OFF OFF ON ENG RET A B C D E F G H I J K L M N O P Q R S T UVWXYZ : = @ # $ % & ( ) * + - . 0 1 2 3 4 5 6 7 8 9 << >> CLR POS END L G_______________ You can use the camera identification to assign a number << >> : Space and character to the camera (0 - 9, A-Z & special character). CLR: Clear the letters.
Menu Operation OSD MENU-Special Menu Settings DPC SET (DEFECT PIXEL CANCELLATION) 2 Adjust the value on WHITE THR(white defect threshold) SPECIAL SHARPNESS MONITOR GAMMA MIRROR USER TITLE DPC SET LANGUAGE EXIT This menu compensate these defect pixels. 1. Select [DPC SET] option on SPECIAL menu and press [ON]. 15 LCD 0.45 OFF OFF ON ENG RET 3. Adjust the value of LUMA LIMIT (Luminance value limitation) OSD MENU-LANGUAGE This menu lets you select English or Korean. 1.
Menu Operation OSD MENU-RESET SETTING CAMERA SETTING EXPOSURE WHITE BAL DAY & NIGHT MOTION DET PRIVACY SPECIAL RESET EXIT ELC ATW AUTO OFF OFF 1. Select [RESET] option. 2. Press OSD key down and the reset menu appears 3. Push OSD key down for FACTORY SET. 4. And move to [EXIT] and click. NOTE: After [EXIT] setting, [RESET] is setting.
Specification Model Signal System Total Pixels No . / Effective Pixels No . Image De vic e Lens Sync. System Scanning Frequency (H/V) Horizontal Resolution S/N Ratio Minimum Illumination Control Method Video Output Signal Day & Night WDR(BLC) Auto Gain Control 30 L2104-DP PAL L2104-DN NTSC 470K/440K 410K/380K 1/3" CCD(ICX638/639BK) 3.6mm Fixed Lens Internal 15.625 KHz/50Hz 15.734 KHz/60 Hz 540 TVL 48 dB ~ 0.05 Lux (F1.
Specification Electronic Shutter Speed White Balance Motion Detection Privacy Zone Masking Monitor Mirror DPC Set Power Consumption Operation Temp./Humidity Storage Temp./Humidity Weight Dimension( øx H) Accessory AUTO, 1/120FLK, 1/250 ~ 1/100000 ATW/AWB/MANUAL/PUSH Set Window / All Set 4 Masks CRT/LCD ON/OFF ON/OFF DC 12V/1.
P/N :
