ENGLISH OWNER’S MANUAL LCD TV 32LD4*** 37LD4*** 42LD4*** 47LD4*** 32LD5*** 42LD5*** 52LD5*** Please read this manual carefully before operating your set and retain it for future reference. www.lg.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
CONTENTS ACCESSORIES ................................................ III PREPARATION CONTENTS Front Panel Controls .......................................... IV Back Panel Information ...................................... VI Stand Installation ............................................. VIII Back Cover for Wire Arrangement .................... VIII Attaching the TV to a desk................................. IX Not Using the desk-type stand........................... IX Swivel Stand ..................
CONTENTS PICTURE CONTROL CONTENTS Picture Size (Aspect Ratio) Control ..................80 Picture Wizard ...................................................82 Energy Saving ...................................................83 Preset Picture Settings .....................................84 Manual Picture Adjustment ...............................85 Picture Improvement Technology......................86 Expert Picture Control .......................................87 Picture Reset ........................
PREPARATION LCD TV MODELS ACCESSORIES PREPARATION Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. ■ Image shown may differ from your TV. This item is not included for all models. * Lightly wipe any stains or fingerprints on the surface of the TV with the polishing cloth. Remote Control Owner’s Manual Batteries (AAA) Polishing Cloth Do not use excessive Polishing cloth for force.
PREPARATION FRONT PANEL CONTROLS NOTE ►TV can be placed in standby mode in order to reduce the power consumption. ► The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost. PREPARATION CAUTION ► Do not drag the TV. The floor or the product may be damaged. ■ Image shown may differ from your TV.
FRONT PANEL CONTROLS ■ Image shown may differ from your TV. Only 32/42/52LD5*** PROGRAMME OK MENU SPEAKER PREPARATION VOLUME INPUT POWER Remote Control Sensor Power/Standby Indicator Intelligent Sensor • Illuminates red in standby mode. Adjusts picture according to the surrounding conditions. • Illuminates blue when the TV is switched on.
USB IN PREPARATION USB IN H/P HDMI IN 2 AV IN 2 2 3 4 5 VIDEO L/MONO AUDIO R 1 6 H/P HDMI IN 2 PREPARATION VIDEO L/MONO AUDIO R Only 32/37/42/47LD4*** VIDEO L/MONO AUDIO R ■ Image shown may differ from your TV. USB IN H/P HDMI IN 2 BACK PANEL INFORMATION 11 2 12 13 AV IN 2 AV IN 2 HDMI / DVI IN VIDEO L/MONO AUDIO R VIDEO L/MONO AUDIO R 1 ANTENNA IN CABLE IN AV IN 1 7 AV IN 1 9 10 RGB IN Input Connect the output from a PC.
PREPARATION BACK PANEL INFORMATION ■ Image shown may differ from your TV. 2 H/P HDMI IN 3 3 4 5 VIDEO L/MONO AUDIO R 1 6 11 2 12 13 PREPARATION USB IN Only 32/42/52LD5*** AV IN 2 2 1 WIRELESS CONTROL VIDEO L/MONO AUDIO R HDMI / DVI IN 2 1 ANTENNA IN CABLE IN AV IN 1 7 1 2 3 8 14 Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. (► p.122) Never attempt to operate the TV on DC power.
PREPARATION PREPARATION STAND INSTALLATION BACK COVER FOR WIRE ARRANGEMENT ■ Image shown may differ from your TV When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. ■ Image shown may differ from your TV.
PREPARATION ATTACHING THE TV TO A DESK NOT USING THE DESK-TYPE STAND (Except 47”,52”models) ■ Image shown may differ from your TV. The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw. ■ Image shown may differ from your TV. When installing the wall-mounted unit, use the protection cover.
PREPARATION KENSINGTON SECURITY SYSTEM ■ This feature is not available for all models. ■ Image shown may differ from your TV. PREPARATION The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. For the detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System. For further information, contact http://www.kensington.
PREPARATION ■ The TV can be installed in various ways such as on a wall, or on a desktop etc. ■ The TV is designed to be mounted horizontally. EARTHING Power Supply Circuit breaker ►Should Install wall mount on a solid wall perpendicular to the floor. ►Should use a special wall mount, if you want to install it to ceiling or slanted wall. ►The surface that wall mount is to be mounted on should be of sufficient strength to support the weight of TV set; e.g. concrete, natural rock, brick and hollow block.
PREPARATION REMOTE CONTROL KEY FUNCTIONS (Only 32/37/42/47LD4***) When using the remote control, aim it at the remote control sensor on the TV. POWER Switches the TV on from standby or off to standby. PREPARATION ENERGY Adjust the Energy Saving mode of the TV.(► p.83) SAVING ENERGY AV MODE AV MODE It helps you select and set images and sounds． / INPUT TV/ RAD INPUT External input mode rotate in regular sequence.(► p.34) SAVING 1 2 3 4 5 6 7 8 9 LIST 0 Q.
PREPARATION VOLUME UP Adjusts the volume. /DOWN FAV Displays the selected favourite programme. ENERGY AV MODE / INPUT SAVING 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW RATIO Selects your desired Aspect Ratio of picture. (► p.80) MUTE Switches the sound on or off. PREPARATION MARK Select the input to apply the Picture Wizard settings. Check and un-check programmes in the USB menu. TV/ RAD Programme Selects a programme.
REMOTE CONTROL KEY FUNCTIONS (Only 32/42/52LD5***) When using the remote control, aim it at the remote control sensor on the TV. POWER Switches the TV on from standby or off to standby. ENERGY Adjust the Energy Saving mode of the TV.(► p.83) SAVING PREPARATION ENERGY AV MODE / INPUT AV MODE It helps you select and set images and sounds TV/ RAD SAVING 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW INPUT External input mode rotate in regular sequence.(► p.34) TV/RAD Selects Radio, TV and DTV channel.
PREPARATION VOLUME UP Adjusts the volume. /DOWN FAV Displays the selected favourite programme. AV MODE / INPUT MARK Select the input to apply the Picture Wizard settings. Check and un-check programmes in the USB menu. TV/ RAD SAVING 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW RATIO Selects your desired Aspect Ratio of picture. (► p.80) PREPARATION ENERGY MUTE Switches the sound on or off. Programme Selects a programme.
U H/P HDMI IN 2 EXTERNAL EQUIPMENT SETUP ■ To prevent damage， do not connect to the mains outlet until all connections are made between the devices. CABLE IN RF Coaxial Wire (75 ohm) VIDEO L/MONO AUDIO R H/P HDMI IN 2 Multi-family Dwellings/Apartments (Connect to wall antenna socket) VIDEO L/MONO AUDIO R Wall Antenna Socket AV IN 2 AV IN 2 VIDEO L/MONO AUDIO R AV IN 1 EXTERNAL EQUIPMENT SETUP H/P HDMI IN 2 AV IN 2 USB IN ■ For optimum picture quality, adjust antenna direction.
EXTERNAL EQUIPMENT SETUP ■ To avoid damaging any equipment, you should never plug in any power cord until you have finished connecting all the equipments. ■ Image shown may differ from your TV. CONNECTING WITH A COMPONENT CABLE This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below.
EXTERNAL EQUIPMENT SETUP CONNECTING WITH AN HDMI CABLE 1 HDMI / DVI IN Turn on the external equipment. 3 Select HDMI1, HDMI2 or HDMI IN 3 (Except for 32/37/42/47LD4***) input source using the INPUT button on the remote control. EXTERNAL EQUIPMENT SETUP 2 VIDEO L/MONO AUDIO R Connect the HDMI output of the external equipment (digital settop box, DVD, etc.) to HDMI/DVI IN 1(DVI)， HDMI IN 2 or HDMI IN 3 (Except for 32/37/42/47LD4***) jack on the TV.
EXTERNAL EQUIPMENT SETUP USB SETUP Connect the USB device to the USB IN jack on the TV. 2 After connecting the USB IN jack, you use the USB function. (► p.41) 1 CONNECTING WITH A RF CABLE To avoid picture noise (interference), allow adequate distance between the VCR and TV. Connect the ANT OUT socket of the VCR to the ANTENNA IN/ CABLE IN socket on the TV. 2 Connect the antenna cable to the ANT IN socket of the VCR.
EXTERNAL EQUIPMENT SETUP CONNECTING WITH A RCA CABLE Connect the AUDIO/VIDEO jacks between TV and VCR or external equipment. Match the jack colours (Video = yellow, Audio Left = white, and Audio Right = red) 2 Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) 1 EXTERNAL EQUIPMENT SETUP 1 Or, Operate the corresponding external equipment. (Refer to external equipment operating guide.) 3 Select AV2 input source using the INPUT button on the remote control.
EXTERNAL EQUIPMENT SETUP CONNECTING WITH A D-SUB 15 PIN CABLE This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. Connect the RGB output of the PC to the RGB IN (PC) jack on the TV. 2 Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV. VIDEO L/MONO AUDIO R EXTERNAL EQUIPMENT SETUP 6 1 1 HDMI / DVI IN 3 Turn on the PC and the TV 4 Select RGB input source using the INPUT button on the remote control.
USB IN EXTERNAL EQUIPMENT SETUP HEADPHONE SETUP 2 To adjust the headphone volume, press the + or - button. If you press the MUTE button, the sound from the headphone is switched off. VIDEO L/MONO AUDIO R Plug the headphone into the headphone socket. AV IN 2 NOTE AV IN 1 VIDEO L/MONO AUDIO VIDEO L/MONO AUDIO R ► AUDIO menu items are disabled when connecting a headphone. ► When changing AV MODE with a headphone connected, the change is applied to video but not to audio.
EXTERNAL EQUIPMENT SETUP DIGITAL AUDIO OUT SETUP Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port. If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp). Connect one end of an optical cable to the TV Digital Audio (Optical) Output port. 2 Connect the other end of the optical cable to the digital audio (Optical) input on the audio equipment.
EXTERNAL EQUIPMENT WIRELESS CONNECTION (Only 32/42/52LD5 ***) You can connect between TV and external equipment wirelessly. For further information, refer to the “LG Wireless Media Box” manual for operating instructions. Connect the Wireless Media Box to the WIRELESS CONTROL jack and HDMI/DVI IN 1, HDMI IN 2 or HDMI IN 3 (Except for 32/37/ 42/47LD4***) jack on the TV.
EXTERNAL EQUIPMENT SETUP SUPPORTED DISPLAY RESOLUTION RGB-PC, HDMI/DVI-PC mode EXTERNAL EQUIPMENT SETUP 10 HDMI/DVI-DTV mode Resolution Horizontal Frequency(kHz) Vertical Frequency(Hz) 720x400 31.468 70.08 640x480 31.469 59.94 800x600 37.879 60.31 1024x768 48.363 60.00 1280x768 47.78 59.87 1360x768 47.72 59.80 1280x1024 63.595 60.00 28.125 50 66.587 59.93 26.97/27 23.97/24 33.716/33.75 29.976/30.00 56.25 50 67.43/67.5 59.
EXTERNAL EQUIPMENT SETUP SCREEN SETUP FOR PC MODE Screen Reset Returns Position, Size and Phase to the factory default settings. This function works in the following mode : RGB[PC]. Move • Sh Sharpn arpn p ess 70 • Colour 70 • Tint SCREEN OK Move Resolution 0 R G • Colour Temp. C50 W C Auto Config. Position To Set • Advanced Control Size ► • Picture Reset Screen •• Screen Prev. Yes No Phase Reset 1 2 3 4 5 EXTERNAL EQUIPMENT SETUP PICTURE Select PICTURE. Select Screen.
EXTERNAL EQUIPMENT SETUP Auto Configure (RGB [PC] mode only) Automatically adjusts the picture position and minimizes image instability. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment. SCREEN PICTURE Move • Sh Sharpn arpn p ess 70 • Colour 70 • Tint Resolution Auto Config. 0 R G • Colour Temp. C50 W C • Advanced Control Position Size • Picture Reset Screen •• Screen Prev.
EXTERNAL EQUIPMENT SETUP Selecting Resolution To view a normal picture, match the resolution of RGB mode and selection of PC mode. This function works in the following mode: RGB[PC] Move • Sh Sharpn arpn p ess 70 • Colour 70 • Tint SCREEN OK Resolution Auto Config. 0 R G • Colour Temp. C50 W C • Advanced Control Prev. 1024 x 768 1280 x 768 1360 x 768 Position Size ► • Picture Reset Screen •• Screen Move Phase Reset 1 2 3 4 EXTERNAL EQUIPMENT SETUP PICTURE Select PICTURE.
EXTERNAL EQUIPMENT SETUP Adjustment for screen Position, Size, Phase If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This function works in the following mode : RGB[PC]. EXTERNAL EQUIPMENT SETUP PICTURE Move • Sh Sharpn arpn p ess 70 • Colour 70 • Tint SCREEN OK Resolution 0 R G W C Position ► Phase Reset 3 4 ► Size • Picture Reset 2 ▲ ◄ • Advanced Control 1 Prev. Auto Config.
WATCHING TV / PROGRAMME CONTROL TURNING ON THE TV When your TV is turned on, you will be able to use its features. 1 Firstly, connect the power cord correctly. At this stage, the TV switches to standby mode. 2 In standby mode to turn TV on, press the / I, INPUT or P button on the TV or press the POWER, INPUT, P or NUMBER button on the remote control and the TV will switch on.
WATCHING TV / PROGRAMME CONTROL QUICK MENU Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently. WATCHING TV / PROGRAMME CONTROL Aspect Ratio: Select your desired picture format. For Zoom Setting, select 14:9, Zoom and Cinema Zoom in Ratio Menu. After completing Zoom Setting, the display goes back to Q.Menu.
WATCHING TV / PROGRAMME CONTROL ON SCREEN MENUS SELECTION AND ADJUSTMENT Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
WATCHING TV / PROGRAMME CONTROL AUTO PROGRAMME TUNING Use this to automatically find and store all available programmes. When you start auto programming, all previously stored service information will be deleted. The maximum number of programmes that can be stored is 500. But the number may be different which depends on broadcasting signals.
WATCHING TV / PROGRAMME CONTROL MANUAL PROGRAMME TUNING (IN DIGITAL MODE) Manual Tuning lets you manually add a programme to your programme list. SETUP SETUP OK Tuning ● Auto ► ● Auto Move ● Programme Tuning Edit ● Programme : On Edit ● Booster OK DTV ► UHF CH. 15 Frequency(kHz) 490000 : On ● Signal Strength 50% ● Signal Quality 50% Add Close 1 2 3 4 5 Select SETUP. • Use NUMBER buttons to input a 4-digit password in Lock System ‘On’. Select Manual Tuning. Select DTV .
WATCHING TV / PROGRAMME CONTROL MANUAL PROGRAMME TUNING (IN ANALOGUE MODE) Manual Tuning lets you manually tune and arrange the stations in whatever order you desire. SETUP Move SETUP OK Tuning ● Auto ► ● Auto ● Programme WATCHING TV / PROGRAMME CONTROL ● Booster Edit ● Programme : On OK ◄ ● Manual Tuning ► ● Manual Tuning Move Tuning Edit ● Booster : On ● Storage ● System I ● System V/UHF ● Channel 0 ● Fine ◄► ● Search ◄► ● Name 2 3 4 5 6 Select SETUP.
WATCHING TV / PROGRAMME CONTROL SETUP Move SETUP OK Tuning ● Auto ► ● Auto ● Programme ● Booster ► ● Manual Tuning Edit OK ◄ ● Manual Tuning ● Programme : On Move Tuning ● Booster Edit : On ► TV ● Storage ● System ● Band ● Storage I ● System V/UHF ● Channel 0 ● Fine ◄► ● Search ◄► ● Name ◄ 1 or C 01 Cable TV ► 1 DK ● Band V/UHF ● Channel 1 ● Fine ◄► ● Search ◄► ● Name C 01 Store Store Close Close You can assign a station name with five characters to each
WATCHING TV / PROGRAMME CONTROL PROGRAMME EDIT When a programme number is skipped, it means that you will be unable to select it using P ton during TV viewing. but- If you wish to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the Programme edit menu. This function enables you to skip the stored programmes. You can change the programme number using “Move”function, if “Automatic Numbering” is unchecked when you start Auto Tuning.
WATCHING TV / PROGRAMME CONTROL IN DTV/RADIO MODE ■ Skipping a programme number 1 Select a programme number to be skipped. 2 BLUE Turn the programme number to blue. 3 BLUE Release. • When programmes are to be skipped, the skipped programme shows in blue and these programmes will not be selected by the P buttons during TV viewing. • If you wish to select a skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or EPG.
WATCHING TV / PROGRAMME CONTROL ■ Skipping a programme number 1 Select a programme number to be skipped. 2 BLUE Turn the programme number to blue. 3 BLUE Release. • When a programme number is skipped it means that you will be unable to select it using the P button during normal TV viewing. • If you wish to select a skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or EPG.
WATCHING TV / PROGRAMME CONTROL BOOSTER(IN AIR DIGITAL MODE) If reception is poor select Booster to On. When the signal is strong, select "Off". ● Manual Move Tuning ● Programme On :: On OK Tuning ● Manual Edit ► Booster ●●Booster ●●Booster Booster Edit Off : :On On On Select SETUP. 2 Select Booster. 3 4 ● Auto Tuning ● Programme 1 SETUP OK ► Move Tuning ► ● Auto WATCHING TV / PROGRAMME CONTROL SETUP Select On or Off. Save.
WATCHING TV / PROGRAMME CONTROL SOFTWARE UPDATE Software Update means software can be downloaded through the digital terrestrial broadcasting system. Software Update Software Update ◄ On ► Picture Test SETUP PICTURE AUDIO Sound Test TIME Signal Test ● Current Version 00.00.01 WATCHING TV / PROGRAMME CONTROL Product/Service Info. Close LOCK INPUT OPTION Press OK( ) to set programme settings. Customer Support 1 2 RED Simple Manual Exit Select Customer Support. Select Software Update.
WATCHING TV / PROGRAMME CONTROL ■ When setting “Software Update” Occasionally, a transmission of updated digital software information will result in the following menu on the TV screen. ? Software update is available. Would you like to download now? Yes No Software Update A window as display below appears when download completes. TV is restarted when "Yes" is selected. New software version is ready. If you want to install now, TV will be turned off and restart.
WATCHING TV / PROGRAMME CONTROL PICTURE/SOUND TEST This function is a customer support function that can execute picture and sound tests. Software update SETUP PICTURE AUDIO TIME Picture Test ? Do you have a problem in this test screen? Sound Test WATCHING TV / PROGRAMME CONTROL 28 Signal Test Product/Service Info. LOCK OPTION Press OK( 2 3 MY MEDIA ) to set programme settings. Customer Support 1 INPUT Simple Manual Exit RED Select Customer Support. Select Picture Test or Sound Test.
WATCHING TV / PROGRAMME CONTROL SIGNAL TEST This function enables you to view information on the Manufacturer, Model/Type and Software Version. This displays the information and signal strength of the tuned *MUX. This displays the signal information and service name of the selected MUX. (*MUX: A higher directory of channels in digital broadcasting (a single MUX contains multiple channels.)) Software update Picture Test SETUP PICTURE AUDIO TIME Sound Test Signal Test Test Signal Product/Service Info.
WATCHING TV / PROGRAMME CONTROL PRODUCT/SERVICE INFORMATION This function is a customer support function that can see product/service information and customer service center information. SETUP PICTURE AUDIO TIME Software update Picture Test Sound Test WATCHING TV / PROGRAMME CONTROL 30 Signal Test LOCK OPTION INPUT MY MEDIA Product/Service Info. Product/Service Info. - MODEL/TYPE : - Software version : 00.00.
WATCHING TV / PROGRAMME CONTROL SIMPLE MANUAL You can easily and effectively access the TV information by viewing a simple manual on the TV. During the Simple Manual operation, audio will be muted. ■ Image shown may differ from your TV. PICTURE AUDIO TIME LOCK OPTION INPUT MY MEDIA Press OK( ) to set programme settings. Customer Support 1 2 Simple Manual Exit GREEN Select Simple Manual. Select the part of the manual you want to see.
WATCHING TV / PROGRAMME CONTROL SELECTING THE PROGRAMME LIST You can check which programmes are stored in the memory by displaying the programme list. Programme List 1 BBC ► Displayed when the Programme is Locked . Exit ► Mini Glossary 2 BBC 3 BBC 4 BBC WATCHING TV / PROGRAMME CONTROL Pr.Edit ■ Displaying programme LIST 1 Display the Programme List. • You may find some blue programmes. These have been set up to be skipped in the programme edit mode.
WATCHING TV / PROGRAMME CONTROL ■ Paging through a programme list 1 Turn the pages. 2 Return to normal TV viewing. Exit Favourite List ◄ ►Favourite Pr. Group ◄ Group B ► ► 1 BBC ► 2 BBC 3 BBC Pr.Reg. 1 Pr.Edit BLUE Turn the programme edit. YELLOW Current channel is registered/ cancelled as preferred channel on currently selected Group. Display the Favourite Programme List. WATCHING TV / PROGRAMME CONTROL ■ Displaying the favourite programme list Favourite group is changed.
WATCHING TV / PROGRAMME CONTROL INPUT LIST By using TV/RAD button, you can move from External Input to RF Input and to the last watched programme in DTV/RADIO/TV mode. Input List WATCHING TV / PROGRAMME CONTROL 34 Move Antenna Cable USB AV1 AV2 Component 2 RGB HDMI1 HDMI2 HDMI3 Input Label OK Component 1 Exit (Except for 32/37/42/47LD4***) 1 Select the input source. • Antenna : Select it when watching the DTV/TV. • Cable : Select it when watching the Cable DTV/Cable TV.
WATCHING TV / PROGRAMME CONTROL INPUT LABEL Select a label for each input source.
WATCHING TV / PROGRAMME CONTROL SIMPLINK This function operates only with devices with the SIMPLINK logo. Please check the SIMPLINK logo. This TV might not function properly when using it with other products with HDMI-CEC function. This allows you to control and play other AV devices connected to the display through HDMI cable without additional cables and settings. If you do not want SIMPLINK menu,select “Off”.
WATCHING TV / PROGRAMME CONTROL Connecting to Home Theater with the SIMPLINK logo. Connect the HDMI/DVI IN 1(DVI), HDMI IN 2 or HDMI IN 3 (Except 32/37/42/47LD4 ***), terminal on the back of the TV and the HDMI output terminal of the Home Theater using HDMI cables. 2 Connect the Digital Audio output terminal on the back of the TV and the Digital Audio input terminal of the Home Theater using optical cables. 3 Select Home Theater in the Speaker menu by pushing the SIMPLINK button.
WATCHING TV / PROGRAMME CONTROL SIMPLINK Functions WATCHING TV / PROGRAMME CONTROL Disc playback Control connected AV devices by pressing the , OK, ►, ▀, l l, ◄◄ and ►► buttons. Direct Play After connecting AV devices to the TV, you can directly control the devices and play media without additional settings. Select AV device Enables you to select one of the AV devices connected to the TV and operate it. Power off all devices When you switch off the TV, all connected devices are turned off.
WATCHING TV / PROGRAMME CONTROL AV MODE You can select the optimal images and sounds. Off Cinema Sport Game Off Cinema Game Sport Press the AV MODE button repeatedly to select the desired source. WATCHING TV / PROGRAMME CONTROL 1 AV MODE Disables the AV MODE. Optimizes video and audio for watching movies. Optimizes video and audio for watching sports events. Optimizes video and audio for playing games.
WATCHING TV / PROGRAMME CONTROL INITIALIZING(RESET TO ORIGINAL FACTORY SETTINGS) This function initializes all settings. But the settings of Day and Night of the Picture Mode cannot be initialized. It is useful to initialize the product or when you move to other city or country. When the Factory Reset is completed, you must restart the Initializing setup. When the Lock System menu is "On", the message to enter the password appears.
TO USE A USB DEVICE WHEN CONNECTING A USB DEVICE When you connect a USB device, this pop up menu is displayed, automatically. “POP UP MENU” will not be displayed while the OSD including Menu, EPG or Schedule list is activated. When the Pop Up menu appears, you can select Music List, Photo List or Movie List in the USB menu. In USB device, you can not add a new folder or delete the existing folder.
TO USE A USB DEVICE Precautions when using the USB device TO USE A USB DEVICE 42 ► Only a USB storage device is recognizable. ► If the USB storage device is connected through a USB hub, the device is not recognizable. ► A USB storage device using an automatic recognition programme may not be recognized. ► A USB storage device which uses its own driver may not be recognized. ► The recognition speed of a USB storage device may depend on each device.
TO USE A USB DEVICE MOVIE LIST You can play movie files on a USB storage device. The movie list is activated once USB is detected. It is used when playing movie files on TV. Displays the movies in the USB folder and supports Play. Allows playback of all movies in the folder and user desired files. It is a movie list that displays folder information and movie file. The On Screen Display may be different from your TV. Images are an example to assist with the TV operation. Movie(*.mpg/*.mpeg/*dat/*.ts/*.trp/*.
TO USE A USB DEVICE File Extension name mpg, mpeg TO USE A USB DEVICE 44 Video Decoder Audio Codec MPEG1, MPEG2 MP2,MP3,AC3,LPCM dat MPEG1 MP2 ts,trp,tp MPEG2, H.264, AVS, VC1 MP2,MP3,AC3,AAC,HEAAC vob MPEG1, 2 MP2,MP3,AC3,LPCM mp4, mov MPEG4,Divx 3.11, Divx 4.12, Divx 5.x, Divx 6, Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03, Xvid 1.10-beta1/2H.264 AAC,HEAAC,MP3 mkv H.264, MPEG-1,2,4 divx, avi MPEG2, MPEG4,DivX 3.11, DivX 4. DivX 5, DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.
TO USE A USB DEVICE Screen Components You can also adjust USB in the INPUT menu. 1 Select MY MEDIA. 2 Select Movie List. 2 1 1 2 3 4 5 Page 1/1 Movie List Drive1 1.
TO USE A USB DEVICE Movie Selection Page 1/1 Movie List Drive1 1. EMF 10_1_Top100 MV TS Page 1/1 20090711 Move To Photo List TO USE A USB DEVICE 46 Change Numbers Play FHD P Page Change Mark Mode MARK Mark e Exit ■ When playing movie files 1 2 3 Select the target folder or drive. Select the desired movie title. Movie files are played. • Use the P button to navigation in the movie page.
TO USE A USB DEVICE ■ When selected movie files are played 1 Select the target folder or drive. 2 3 Select the desired movie title. BLUE the marked movies will be played in sequence. Convert to Mark Mode. 4 5 • When one or more movie files are marked, Selected desired movie file. RED Selected movie file is played. NOTE ► In the case of files not supported, a message regarding non-supported file is displayed. TO USE A USB DEVICE • Press the BACK button to return to normal TV viewing.
TO USE A USB DEVICE Using the remote control GREEN Repeatedly, press the GREEN button to converted to Photo List->Music List. YELLOW A method to view in 5 large photos or simple list. BLUE Convert to Mark Mode. Rerurn to normal viewing. EXIT ► TO USE A USB DEVICE 48 Press the PLAY(►) button to return to normal playback.
TO USE A USB DEVICE Using the Movie List function, play Choose options. Set Video Play. Set Video. Set Audio. ■ ► or 2 II 01:02:30 / 02:30:25 ◄◄ ►► Q.MENU Option Hide Exit Show the Popup menu. Select Set Video Play., Set Video. or Set Audio.. TO USE A USB DEVICE 1 Close ◄► ► NOTE ► Option values changed in Movie List does not affect Photo List and Music List. ► Option value changed in Photo List and Music List are changed likewise in Photo List and Music List excluding Movie List.
Using the remote control ■ ► II ◄◄ / ►► Stop the playing movie file. Press the PLAY(►) button to return to normal playback. During playback, press the Pause(II) button. ■ Still screen is displayed. ■ If no buttons are pressed on the remote control for 10 minutes after pausing, the TV returns to the playback state. ■ Press the Pause(II) button and then use the FF(►►) button for slow motion.
TO USE A USB DEVICE ■ When you select the Set Video Play, Set Video Play. Picture Size ◄ Full ► Audio Language ◄ 1 ► Subtitle Language ◄ Off ► ● Language ◄ Off ► ● Code page ◄ ● Sync ◄ 0 ► ● Position ◄ 0 ► ● Size ◄ Normal ► Repeat ◄ Off ► Simplilied Chinese ► Previous 1 Select Picture Size, Audio Language, Subtitle Language or Repeat. Make appropriate adjustments.
TO USE A USB DEVICE ■ When you select the Set video, Set Video. Picture Mode ◄ TO USE A USB DEVICE 52 2 ► ● Backlight 70 ◄ ► ● Contrast 95 ◄ ► ● Brightness 50 ◄ ► ● Colour 70 ◄ ► ● Dynamic Contrast ◄ Medium ► ● Edge Enhancer ◄ High ► ● Noise Reduction ◄ Medium ► TruMotion ◄ Low ► Picture Reset 1 Standard (Only 32/42/52LD5 ***) Previous Select Picture Mode or TruMotion. Make appropriate adjustments.
TO USE A USB DEVICE ■ When you select the Set Audio, Set Audio. Sound Mode ◄ Standard ► Auto Volume ◄ Off ► Clear Voice II ◄ Off ► Balance 0 ◄ L R ► Prev. 2 Select Sound Mode, Auto Volume, Clear Voice II or Balance. Make appropriate adjustments.
TO USE A USB DEVICE PHOTO LIST You can view photo files on USB storage device. The On Screen Display may be different from your TV. Images are an example to assist with the TV operation. When you are watching the photo by the Photo List function, you can not change the picture mode. PHOTO(*.JPEG) supporting file Baseline : 64 x 64 ~ 15360 x 8640 Progressive : 64 x 64 ~ 1920 x 1440 • You can play JPEG files only. • Non-supported files are displayed in the form of predefined icon.
TO USE A USB DEVICE Using the remote control GREEN Repeatedly, press the GREEN button to converted to Music List->Movie List. YELLOW A method to view in 5 large photos or simple list. BLUE Convert to Mark Mode. Rerurn to normal viewing.
TO USE A USB DEVICE Photo Selection Page 1/1 Photo List Drive1 1. EMF Ental 10_1_Top 100 2009_5_3_TOP... FHD 20090711 HD MV Page 1/1 20090810 Photo Move To Music List Change Numbers ■ When playing photo files TO USE A USB DEVICE 56 1 2 3 200942_Top100 2.DVDRip.AC... 20091010 TS View Mark Mode P Page Change MARK Select the desired photos. Photo files are displayed. Mark Exit • Use the P button to navigation in the photo page. Select the target folder or drive.
TO USE A USB DEVICE ■ When selected photo files are displayed 1 Select the target folder or drive. 2 3 Select the desired photos. BLUE 4 5 • When one or more photos are marked, you can view each marked photo or a slide show of the marked photos. If no photos are marked, you can view every individual photo in the folder or a slide show of all photos in the folder. Convert to Mark Mode. Selected desired photo file. RED Selected photo file is played.
TO USE A USB DEVICE How to view photo Detailed operations are available on full-sized photo view screen. Page 1/1 Photo List Drive1 1. EMF 10_1_Top 100 Ental 20090711 2009_5_3_TOP... FHD HD Page 1/1 20090810 MV 200942_Top100 Photo View P Page Change Mark Mode Change Numbers Basic Test Kit TS Move To Music List 2.DVDRip.AC... 20091010 MARK Mark Exit TO USE A USB DEVICE 01_a.
TO USE A USB DEVICE Select the Slideshow, 01_a.jpg 2008/12/10 1920 x 1080 479 KB 4 ◄ ► BGM, (Rotate), (ZOOM IN), Option, Hide or Exit. • Use !button to select the previous ◄ Slideshow ► BGM ■ 2/13 ► Q.MENU Option Hide Exit or next photo. • Use !button to select and control the menu on the full-sized screen. ► Slideshow : When no picture is selected, all photos in the current folder are displayed during slide show. If some photos are selected, those photos are displayed in a slide show.
TO USE A USB DEVICE Using the Photo List function 01_a.jpg 2008/12/10 1920 x 1080 479 KB Choose options. Set photo view. ◄ ► Set video. Set audio. Close ◄ Slideshow 1 TO USE A USB DEVICE 60 ► or 2 BGM ■ 2/13 ► Q.MENU Option Hide Exit Show the Popup menu. Select Set photo view., Set video. or Set audio.. NOTE ► Option values changed in Photo List does not affect Movie List and Music List.
TO USE A USB DEVICE ■ When you select the Set photo view, Set photo view. Slide Speed BGM ◄ Fast ► 2009_5_3_TOP100+(_... ● Repeat ◄ Off ► ● Random ◄ Off ► Prev. 1 2 Select Slide Speed or BGM Make appropriate adjustments.
TO USE A USB DEVICE ■ When you select the Set video, Set Video. Picture Mode ◄ TO USE A USB DEVICE 62 2 ► 70 ◄ ► ● Contrast 95 ◄ ► ● Brightness 50 ◄ ► ● Colour 70 ◄ ► ● Dynamic Contrast ◄ Medium ► ● Edge Enhancer ◄ High ► ● Noise Reduction ◄ Medium ► TruMotion ◄ Low ► Picture Reset 1 Standard ● Backlight (Only 32/42/52LD5 ***) Previous Select Picture Mode or TruMotion. Make appropriate adjustments.
TO USE A USB DEVICE ■ When you select the Set Audio, Set Audio. Sound Mode ◄ Standard ► Auto Volume ◄ Off ► Clear Voice II ◄ Off ► Balance 0 ◄ L R ► Prev. 2 Select Sound Mode, Auto Volume, Clear Voice II or Balance. Make appropriate adjustments.
TO USE A USB DEVICE MUSIC LIST You can play music files on USB storage device. Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files may not be supported by this model. Music file on your USB device can be played by this unit. The On Screen Display may be different from your TV. Images are an example to assist with the TV operation. MUSIC (*.MP3) supporting file Bit rate 32 ~ 320 • Sampling rate MPEG1 Layer3 : 32kHz, 44.1kHz, 48kHz • Sampling rate MPEG2 Layer3 : 16kHz, 22.
TO USE A USB DEVICE Using the remote control GREEN Repeatedly, press the GREEN button to converted to Movie List->Photo List. YELLOW A method to view in 5 large photos or simple list. BLUE Convert to Mark Mode. Rerurn to normal viewing.
TO USE A USB DEVICE Music Selection Page 1/1 Music List Drive1 001. - Diet(feat.).mp3 00:00 Page 1/1 002. -Mad(Feat.).mp3 00:00 003. 2NE1 - Fire.mp3 00:00 004. - Melody.mp3 00:00 005. - Gift.mp3 00:00 Move To Movie List TO USE A USB DEVICE ■ When playing music files 1 2 3 66 Change Numbers Select the target folder or drive. Select the desired music title. Music files are played. Play Mark Mode P Page Change MARK Mark Exit • Use the P button to navigate up/down in the music page.
TO USE A USB DEVICE ■ When selected music files are played 1 Select the target folder or drive. 2 3 Select the desired music title. BLUE 4 5 Convert to Mark Mode. Selected desired music file. RED Selected music file is played. TO USE A USB DEVICE • Press the BACK button to return to normal TV viewing.
TO USE A USB DEVICE Using the Music List function, play Page 1/1 Music List 3 file(s) Marked Drive1 Page 1/1 Set Audio Play. ► 004. - Diet (feat).mp3 00:00 005. - Mad (Feat).mp3 ■ 1 TO USE A USB DEVICE 68 II ► or 2 005. - Mad (Feat).mp3 00:00 ► ◄◄ ►► Choose options. Set audio. 006. - Melody.mp3 00:00 ◄► Play with Photo 007. - Melody.mp3 00:00 008. - Melody.mp3 00:00 Close 02:30 / 03:25 Q.MENU Option Hide Exit Show the Popup menu. Select Set audio play. or Set audio.
TO USE A USB DEVICE Using the remote control ■ ► II ◄◄ / ►► GREEN ENERGY SAVING Start playing the selected music files and then move to the Photo List. Press the ENERGY SAVING button repeatedly to increase the brightness of your screen.(Refer to p. 95) Only Off/Screen Off operates from the Movie List, Photo List, Music List. Show the Option menu. ■ When you press the Back button while the music is playing, the music player currently playing will be hidden and only the music list will be displayed.
TO USE A USB DEVICE ■ When you select the Set audio play, Set Audio Play. Repeat ◄ On ► Random ◄ Off ► Prev. 1 2 TO USE A USB DEVICE 70 Select Set Audio Play. Make appropriate adjustments.
TO USE A USB DEVICE ■ When you select the Set audio, Set audio. Sound Mode ◄ Standard ► Auto Volume ◄ Off ► Clear Voice II ◄ Off ► Balance 0 ◄ L R ► Prev. 2 Select Sound Mode, Auto Volume, Clear Voice II or Balance. Make appropriate adjustments.
TO USE A USB DEVICE ■ If you don't press any button for a while during the playing, the play information box (as shown in the below) will float as a screen saver. ■ The ‘Screen Saver’? Screen saver is to prevent screen pixel damage due to an fixed image remaining on the screen for a extended period of time. Again&Again.mp3 ► 00:31 / 04:04 NOTE TO USE A USB DEVICE 72 ► A damaged or corrupted music does not play but displays 00:00 in playtime.
TO USE A USB DEVICE DIVX REGISTRATION CODE Confirm the DivX registration code number of the TV. Using the registration number, movies can be rented or purchased at www.divx.com/vod. With a DivX registration code from other TV, playback of rented or purchased DivX file is not allowed. (Only DivX files matched with the registration code of the purchased TV are playable.) MY MEDIA DivX Reg.Code Deactivation Movie List Press OK( Photo List ) to see photos from the USB.
TO USE A USB DEVICE DEACTIVATION The purpose of deactivation is to allow deactivation of devices for users who have activated all the available devices through the web_server and are blocked from activating more devices. DivX VOD allowed the consumer to activate up to 6 devices under one account, but to replace or deactivate any of those devices, the consumer had to contact DivX Support and request deletion.
EPG(ELECTRONIC PROGRAMME GUIDE) (IN DIGITAL MODE) This system has an Electronic Programme Guide (EPG) to help your navigation through all the possible viewing options. The EPG supplies information such as programme listings, start and end times for all available services. In addition, detailed information about the programme is often available in the EPG (the availability and amount of these programme details will vary, depending on the particular broadcaster).
EPG (ELECTRONIC PROGRAMME GUIDE) Switch on/off EPG 1 Switch on or off EPG. Select a programme 1 or Select desired programme. 2 The EPG will disappear after moving to a selected program. Button Function in NOW/NEXT Guide Mode You can view a program being broadcasted and one scheduled to follow. EPG (ELECTRONIC PROGRAMME GUIDE)(IN DIGITAL MODE) 76 RED Change EPG mode. Programme Guide ▲ That ’70s show Nov. 25, 2008 10:05 1 YLE TV1 25 Nov. 2008 09:45~10:15 YELLOW BLUE Enter Manual Timer mode.
EPG (ELECTRONIC PROGRAMME GUIDE) Button Function in 8 Day Guide Mode Programme Guide ▲ That ’70s show Change EPG mode. ALL 15:00 ▼ Kungskonsumente Antigues Roadshow The Drum Mint Extra TV2: Farmen The Drum You Call The Hits Fashion Essentials ... ... ... Tänään otsikoissa 2 YLE TV2 Enter Date setting mode. 4 TV.. 5 YLE FST 6 CNN YELLOW 8 YLE24 Enter Manual Timer mode. FAV Favourite Mode BLUE Tue, Nov. 25 14:00 1 YLE TV1 GREEN ◄ RED Nov. 25, 2008 10:05 1 YLE TV1 25 Nov.
EPG (ELECTRONIC PROGRAMME GUIDE) Button Function in Date Change Mode Programme Guide ▲ That ’70s show Nov. 25, 2008 10:05 1 YLE TV1 25 Nov. 2008 09:45~10:15 ◄ Change to the selected date. ALL 4 TV.. 5 YLE FST 6 CNN 8 YLE24 Switch off Date setting mode. 15:00 ▼ 2 YLE TV2 Select a date. Tue. 25 Nov. 14:00 1 YLE TV1 ... ◄ GREEN Switch off Date setting mode. Kungskonsumente Antigues Roadshow The Drum Mint Extra TV2: Farmen The Drum You Call The Hits Fashion Essentials ... ... ...
EPG (ELECTRONIC PROGRAMME GUIDE) Button Function in Remind Setting Mode Sets only a start time for the reminder with the end time grayed out. Manual Timer Switch off Manual Timer mode. Select the date to schedule. Sun. Select Start Time, End time or Programme. Mon. Tue. Wed., Aug. 12 2009 13:46 Wed. Thu. Select 10 the date 11 to remind 12 09 16 17 Time18 Start Fri. 13 End19Time 14 Sat. Wed. 12 Aug. 2009 15 20 21 Programme 22 DTV 27 801 ANTV 28D...
PICTURE CONTROL PICTURE SIZE (ASPECT RATIO) CONTROL You can watch the screen in various picture formats; 16:9, Just Scan, Original, Full Wide, 4:3, 14:9, Zoom and Cinema Zoom. If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible. You can adjust the enlarge proportion using button. This function works in the following signal. 1 2 Select Aspect Ratio. PICTURE menu.
PICTURE CONTROL • 4:3 The following selection will allow you to view a picture with an original 4:3 aspect ratio, black bars will appear on both the left and right of the screen. • 14:9 You can view a picture format of 14:9 or a general TV programme in the 14:9 mode. The 14:9 screen is viewed in the same way as in 4:3, but is moved to the up and down. • Zoom The following selection will allow you to view the picture without any alteration, while filling the entire screen.
PICTURE CONTROL PICTURE WIZARD This feature lets you adjust the picture quality of the original image. Use this to calibrate the screen quality by adjusting the Black and White Level etc. General users can calibrate the screen quality by easily following each stage. When you adjust the image to Low, Recommended or High, you can see the changed result as an example. In RGB-PC/HDMI-PC/DVI-PC mode, the changed Colour, Tint and H/V Sharpness values are not applied.
PICTURE CONTROL ENERGY SAVING It reduces the TV’s power consumption. The default factory setting complies with the Energy Star requirements and is adjusted to the comfortable level to be viewed at home. You can increase the brightness of your screen by adjusting the Energy Saving level or by setting the Picture Mode. When adjusting Energy Saving in MHEG mode, the Energy Saving setting is applied after MHEG is finished.
PICTURE CONTROL PRESET PICTURE SETTINGS Picture Mode-Preset Strengthen the contrast, brightness, colour and sharpness for vivid picture. The most general screen display status. Optimizes video for watching movies. Optimizes video for watching sports events. Optimizes video for playing games.
PICTURE CONTROL MANUAL PICTURE ADJUSTMENT Picture Mode-User option Backlight To control the brightness of the screen, adjust the brightness of LCD panel. Adjusting the backlight when setting the brightness of the set is recommended. Contrast Adjusts the signal level between black and white in the picture. You may use Contrast when the bright part of the picture is saturated. Brightness Adjusts the base level of the signal in the picture.
PICTURE CONTROL PICTURE IMPROVEMENT TECHNOLOGY You can calibrate the screen for each Picture Mode or set the video value according to the special video screen. You can set the video value differently for each input. To reset to the factory default screen after making adjustments to each video mode, execute the “Picture Reset” function for each Picture Mode. Image shown may differ from your TV.
PICTURE CONTROL EXPERT PICTURE CONTROL By segmenting categories, Expert1 and Expert2 provide more categories which users can set as they see fit, offering the optimal picture quality for users. This may also be used to help a professional optimize the TV performance using specific videos. Image shown may differ from your TV.
PICTURE CONTROL *This feature is not available for all models. Dynamic Contrast (Off/Low/Medium/High) Dynamic Colour (Off/Low/High ) ■ Adjusts the contrast to keep it at the best level according to the brightness of the screen. The picture is improved by making bright parts brighter and dark parts darker. ■ Adjusts screen colours so that they look livelier, richer and clearer. This feature enhances hue, saturation and luminance so that red, blue, green and white look more vivid.
PICTURE CONTROL Colour Gamut (Advanced Control: Wide/Standard) Colour Gamut (Expert Control: EBU/ SMPTE/BT709/Wide) Edge Enhancer (Off/Low/High) • Standard : Mode to reproduce original colour according to the standard of input signal independent of the display characteristics. • Wide: Mode to use and set the rich colour area of the display. ■ Maximize the utilization for colour area that can be expressed. ■ Displays color domain of signal in Expert Control.
PICTURE CONTROL PICTURE RESET Settings of the selected picture modes return to the default factory settings. PICTURE Move • Br Bri Bright ightness PICTURE OK 50 • Sharpness 70 • Colour 70 R G 0 W C • Tint PICTURE CONTROL 2 3 4 70 ► • Advanced Control Yes No •• Picture Picture Reset Reset ► 1 • Sharpness OK • Colour Temp. C50 • Advanced Control • Screen 50 • Colour? All picture 70 Rsetting willGbe reset. C • Tint 0 W Continue? • Colour Temp.
PICTURE CONTROL TRUMOTION (Only 32/42/52LD5 ***) It is used for the best picture quality without any motion blur or judder when you enter a quick image or Film Source. High : Provide smoother picture movement. Low : Provide smooth picture movement. Use this setting for standard use. Off : Turn off TruMotion Operation. User : User can adjust Judder and Blur level in TruMotion Operation, separately. - Judder : Adjust noise of the screen. - Blur : Adjust after-image of the screen.
PICTURE CONTROL POWER INDICATOR It helps you adjust the brightness of moving LED when power is turned on. Standby Light Determines whether to set the indicator light on the front of the TV to On or Off in standby mode. Power Light Determines whether to set the indicator light on the front of the TV to On or Off when the power turns on.
PICTURE CONTROL MHEG GUIDE This menu determines whether to show the UI guide or the guide provided by MHEG when a user hits the 'GUIDE' key. If you set the 'MHEG Guide' menu to On, the 'Digital Teletext' sent by broadcasters will be used. Note that 'Digital Teletext' is not always present. ● Country/Area ● Hard Indicator ● MHEG Guide : ● Factory Reset :1 ● Set : Home Use • Mode Setting Select OPTION. 2II Off On :1 : Home Use 3 Select O n or O f f. OK 4 OK Save.
PICTURE CONTROL MODE SETTING We recommend setting the TV to “Home Use ” mode for the best picture in your home environment. “Store Demo ” mode is an optimal setting for displaying at stores. Move OPTION OK Move ● Language(Language) ● Language(Language) ● Country/Area ● Country/Area ● Hard : HongKong of Hearing( ):Off Indicator ● MHEG Guide ● Hard ● Power ● Set : Off Reset ID ● MHEG Guide ::Home HomeUse Use ● Set : Off Reset ID :1 Selecting the environment.
PICTURE CONTROL DEMO MODE Display the slide show to explain the various logo of this TV. It is not possible to use Demo Mode in Home Use mode. In Store Demo, Demo Mode is automatically set to On. Once Demo Mode is set to Off in Store Demo, Demo Mode does not run and only the screen is reset. The screen is reset automatically after 5 minutes in Demo Mode.
SOUND & LANGUAGE CONTROL AUTO VOLUME LEVELER AVL automatically remains on the same level of volume if you change programmes. Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time when the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each program.
SOUND & LANGUAGE CONTROL CLEAR VOICE II By differentiating the human sound range from others, it helps users listen to human voices better. AUDIO Move Volume Off :: Off ● Balance ● Sound Mode ● Auto 33 0 L R 3 Off :: Off ● Clear Voice II L 0 ● Level R 33 ● Balance Mode ◄ 3 Off - • Infinite Sound : Off • Treble 50 • Treble 50 5 + • Bass 50 • Bass 50 Close • Re Resett • If you select “On” for Clear Voice II, Infinite Sound feature will not work.
SOUND & LANGUAGE CONTROL PRESET SOUND SETTINGS-SOUND MODE You can select your preferred sound setting; Standard, Music, Cinema, Sport or Game and you can also adjust the Treble, Bass. Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound options based on the programme content. Standard, Music, Cinema, Sport and Game are preset for optimum sound quality at the factory. Offers standard-quality sound. Optimizes sound for listening to music.
SOUND & LANGUAGE CONTROL SOUND SETTING ADJUSTMENT -USER MODE AUDIO Move Volume ● Clear Voice II : Off ● Auto 3 0 L R Sound Mode Mode ●●Sound ► Standard(User) :: Standard 3 4 5 OK : Off 3 L R Standard(User) 0 Standard Standard(User) :: Standard Music • Treble 50 • Infinite Sound : OffCinema • Treble 50 Sport • Bass 50 • Bass • Re R sett 2 Voice II Move : Off ● Balance • Infinite Sound : Off 1 Volume ● Clear ● Balance Sound Mode Mode ●●Sound AUDIO OK : Off ► ● Auto 5
SOUND & LANGUAGE CONTROL BALANCE You can adjust the sound balance of the speakers to preferred levels.
SOUND & LANGUAGE CONTROL TV SPEAKERS ON/ OFF SETUP You can adjust the TV internal speaker status. In AV, COMPONENT, RGB and HDMI1 with HDMI to DVI cable, the TV speaker can be operational even when there is no video signal. If you wish to use an external Hi-Fi system, turn off the TV’s internal speakers.
SOUND & LANGUAGE CONTROL DTV AUDIO SETTING (IN DIGITAL MODE ONLY) When different audio types exist in an input signal, this function allows you to select the audio type you want.
SOUND & LANGUAGE CONTROL SELECTING DIGITAL AUDIO OUT This function allows you to select your preferred Digital Audio Output. The TV can only output DOLBY Digital if a channel is broadcast with Dolby Digital audio. When Dolby digital is available, selecting Auto in the Digital Audio Out menu will set SPDIF(Sony Philips Digital InterFace) output to Dolby Digital. If Auto is selected in the digital audio out menu when dolby digital is not available, SPDIF output will be PCM(Pulse-code modulation).
SOUND & LANGUAGE CONTROL AUDIO RESET Settings of the selected Sound Mode return to the default factory settings.
SOUND & LANGUAGE CONTROL STEREO/DUAL RECEPTION (IN ANALOGUE MODE ONLY) When a programme is selected, the sound information for the station appears with the programme number and station name. 1 Select Audio Language. 2 Select the sound output. Broadcast On Screen Display Mono MONO Stereo STEREO Dual DUAL I, DUAL II, DUAL I+II ■ Language selection for dual language broadcast If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II.
SOUND & LANGUAGE CONTROL NICAM RECEPTION (IN ANALOGUE MODE ONLY) If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received. Sound output can be selected according to the type of broadcast received. 1 SOUND & LANGUAGE CONTROL 106 When NICAM mono is received, you can select NICAM MONO or FM MONO. 2 When NICAM stereo is received, you can select NICAM STEREO or FM MONO.
SOUND & LANGUAGE CONTROL ON-SCREEN MENU LANGUAGE/COUNTRY/AREA SELECTION The installation guide menu appears on the TV screen when it is switched on for the first time. 1 Select your country. * If you want to change Language/Area or Country selection 1 2 Select Language(Language). 3 4 Select Menu Language. Select your desired language. Select OPTION. 2 Select City/Area. 3 4 Select your country. Save. Save. • Press the MENU/EXIT button to return to normal TV viewing.
SOUND & LANGUAGE CONTROL LANGUAGE SELECTION (IN DIGITAL MODE ONLY) The Audio function allows selection of a preferred language. If audio data in a selected language is not broadcast, the default language audio will be played. Use the Subtitle function when two or more subtitle languages are broadcast. If subtitle data in a selected language is not broadcast, the default language subtitle will be displayed.
SOUND & LANGUAGE CONTROL Audio Language OSD Information < Audio Language Selection > ► When two or more audio languages are broadcast, you can select the audio language. Display N.A Status Not Available MPEG Audio l Dolby Digital Audio Audio for “Visual Impaired” 1 2 Audio for “Hearing Impaired” Dolby Digital Plus Audio Select Audio Language. Select an audio language.
TIME SETTING CLOCK SETUP The clock is set automatically after a digital signal is received.(You can set the clock manually only if the TV has no DTV signal.) You must set the time correctly before using on/off timer function. TIME Move TIME OK Move ● Clock ► ● Clock ◄ OK ► Auto ● Off Time : Off ● Off Time : Off Year 2008 ● On Time : Off ● On Time : Off Month Mar.
TIME SETTING AUTO ON/OFF TIME SETTING The Off time function automatically switches the TV to standby at a preset time. Two hours after the TV is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed. The Off time function overrides the On time function if both are set to the same time. The TV must be in standby mode for the On time to work.
TIME SETTING SLEEP TIMER SETTING You do not have to remember to switch the TV off before you go to sleep. The sleep timer automatically switches the TV to standby after the preset time has elapsed. 1 2 Select Sleep Timer. Select Off, 10, 20, 30, 60, 90, 120, 180 or 240 min.. • When you switch the TV off, the preset sleep timer is cancelled. • You can also adjust Sleep Timer in the TIME menu.
PARENTAL CONTROL / RATINGS SET PASSWORD & LOCK SYSTEM Enter the password, press ‘0’, ‘0’, ‘0’, ‘0’ on the remote control handset. If a channel is locked, enter the password to unlock it temporarily. LOCK OK Lock : :Off Off Move ● Lock System Off Off : :Off Off ● Block Programme ● Block Programme ● Input Block ● Input Block : Off ● Key Select LOCK.
PARENTAL CONTROL / RATINGS BLOCK PROGRAMME Blocks any programme that you do not want to watch or that you do not want your children to watch. It is available to use this function when Lock System ”On”. Enter a password to watch a blocked programme.
PARENTAL CONTROL / RATINGS EXTERNAL INPUT BLOCKING Enables you to block an input. It is available to use this function when Lock System ”On”.
PARENTAL CONTROL / RATINGS KEY LOCK The TV can be set so that the remote control is required. This feature can be used to prevent unauthorized viewing. LOCK Move OK Password ● Lock System ●● Key Key Lock Lock LOCK ● Set : Off Move ● Lock System : Off Programme ● Block Programme ● Input Block ● Input Block : Off : Off OK Password ● Block ► ● Set ● Key Lock : :Off Off Off Off On 1 Select LOCK. 2 Select Key Lock. 3 4 PARENTAL CONTROL / RATINGS 116 Select On or Off.
DIGITAL TELETEXT The TV gives you access to digital teletext which is greatly improved in various aspects such as text, graphics etc. This digital teletext can access special digital teletext services and specific services which broadcast digital teletext. You should select off in the subtitle language menu to display teletext by pressing the SUBTITLE button. ■ Image shown may differ from your TV.
DIGITAL TELETEXT TELETEXT IN DIGITAL SERVICE 1 Press the numeric or P 2 Press the GUIDE, TEXT or coloured button to switch on teletext. 3 Follow the indications on digital teletext and move onto the next step by pressing OK, GREEN, YELLOW, BLUE or NUMBER buttons and so on. 4 Press the GUIDE, TEXT or colour button to switch off digital teletext and return to TV viewing. button to select a certain service which broadcasts digital teletext.
APPENDIX TROUBLESHOOTING The TV does not operate properly. Check to see if there is any object between the TV and the remote control causing an obstruction. Ensure you are pointing the remote control directly at the TV. A Ensure that the batteries are installed with correct polarity (+ to +, - to -). A Install new batteries. A The remote control does not work Power is suddenly turned off Is the sleep timer set? A Check the power control settings. Has the Power supply been interrupted.
APPENDIX The audio function does not work. A + or - button. Press the Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly? A Adjust Balance in menu option. Unusual sound from inside the TV A A change in ambient humidity or temperature may result in an unusual noise when the TV is switched on or off and does not indicate a fault with the TV. No sound when connecting HDMI or USB A Check HDMI cable over version 1.3.
APPENDIX MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV. Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.
APPENDIX PRODUCT SPECIFICATIO NS MODELS Dimensions 47LD4** 32LD450-CA 37LD450-CA 42LD450-CA 47LD450-CA without stand 799.0 x 506.0 x 73.5 mm 31.4 x 19.9 x 2.9 inches 916.0 x 575.0 x 77.4 mm 36.0 x 22.6 x 3.0 inches with stand without stand 9.3 kg / 20.7 lbs 8.2 kg / 18.2 lbs 12.9 kg / 28.7 lbs 11.3 kg / 25.1 lbs 14.9 kg / 33.1 lbs 13.3 kg / 29.5 lbs 19.2 kg / 42.6 lbs 17.2 kg / 38.2 lbs AC100-240V~ 50/60Hz AC100-240V~ 50/60Hz AC100-240V~ 50/60Hz AC100-240V~ 50/60Hz 1023.0 x 635.0 x 76.
APPENDIX IR CODES *This feature is not available for all models. Code (Hexa) Function Note 95 Energy Saving R/C BUTTON 08 POWER R/C BUTTON(POWER ON/OFF) 0B INPUT R/C BUTTON 79 RATIO R/C BUTTON F0 TV/RAD R/C BUTTON 45 Q.
APPENDIX EXTERNAL CONTROL DEVICE SETUP RS-232C Setup OPTICAL DIGITAL AUDIO OUT N VIDEO /MONO AUDIO VI) Y PB PR R L AUDIO VIDEO AV IN 1 Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Note: RS-232C connection cables are not supplied with the product.
APPENDIX Set ID Use this function to specify a set ID number. Refer to ‘Real Data Mapping’. ► p.
APPENDIX Communication Parameters ■ ■ ■ ■ ■ Baud rate : 9600 bps (UART) Data length : 8 bits Parity : None Stop bit : 1 bit Communication code : ASCII code ■ Use a crossed (reverse) cable. Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] Command Reference List COMMAND COMMAND 1 2 APPENDIX 126 01. Power k 02. Aspect Ratio 03. Screen Mute DATA (Hexadecimal) a 00 ~ 01 k c Refer to p. 127 k d 00 ~ 01 04. Volume Mute k e 00 ~ 01 05.
APPENDIX 01. Power (Command: k a) ► To control Power On/Off of the set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off Ack 01 : Power On [a][ ][Set ID][ ][OK/NG][Data][x] ► To show Power On/Off. Transmission ► To control volume mute on/off. You can also adjust mute using the MUTE button on remote control.
APPENDIX 09. Tint (Command: k j) ► To adjust the screen tint. You can also adjust tint in the PICTURE menu. Transmission 13. Treble (Command: k r) ► To adjust treble. You can also adjust treble in the AUDIO menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] [k][r][ ][Set ID][ ][Data][Cr] Data Red : 00 ~ Green : 64 * Refer to ‘Real data mapping 1’. See page 129. Ack Data Min : 00 ~ Max : 64 * Refer to ‘Real data mapping 1’. See page 129.
APPENDIX 17. Energy Saving (Command: j q) 19.Tune Command (Command: m a) ► To reduce the power consumption of the TV. You can also adjust Energy Saving in OPTION menu. Transmission ► Select channel to following physical number. Transmission [j][q][ ][Set ID][ ][Data][Cr] Data00 : High channel data Data01 : Low channel data ex. No. 47 -> 00 2F (2FH) No. 394 -> 01 8A (18AH), DTV No.
APPENDIX 21. Key(Command: m c) ► To send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code - Refer to page 123. Ack [c][ ][Set ID][ ][OK/NG][Data][x] 23. Input select (Command: x b) (Main Picture Input) ► To select input source for main picture. Transmission [x][b][ ][Set ID][ ][Data][Cr] Data Structure MSB 0 LSB 0 0 0 External Input External Input 22.
APPENDIX Open source software notice The following GPL executables and LGPL/MPL libraries used in this product are subject to the GPL2.0/LGPL2.1/MPL1.1 License Agreements: GPL EXECUTABLES: • Linux kernel 2.6 • busybox • lzo LGPL LIBRARIES: • uClibc MPL LIBRARIES: • Nanox LG Electronics offers to provide source code to you on CD-ROM for a charge covering the cost of performing such distribution, such as the cost of media, shipping and handling upon e-mail request to LG Electronics at: opensource@lge.
APPENDIX OPEN SOURCE LICENSE GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
APPENDIX 1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
APPENDIX If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License.
APPENDIX NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
APPENDIX GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
APPENDIX Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library".
APPENDIX Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
APPENDIX c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.
APPENDIX 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
APPENDIX MOZILLA PUBLIC LICENSE Version 1.1 --------------1. Definitions. 1.0.1. "Commercial Use" means distribution or otherwise making the Covered Code available to a third party. 1.1. "Contributor" means each entity that creates or contributes to the creation of Modifications. 1.2. "Contributor Version" means the combination of the Original Code, prior Modifications used by a Contributor, and the Modifications made by that particular Contributor. 1.3.
APPENDIX (b) under Patents Claims infringed by the making, using or selling of Original Code, to make, have made, use, practice, sell, and offer for sale, and/or otherwise dispose of the Original Code (or portions thereof). (c) the licenses granted in this Section 2.1(a) and (b) are effective on the date Initial Developer first distributes Original Code under the terms of this License. (d) Notwithstanding Section 2.
APPENDIX (b) Contributor APIs. If Contributor's Modifications include an application programming interface and Contributor has knowledge of patent licenses which are reasonably necessary to implement that API, Contributor must also include this information in the LEGAL file. (c) Representations. Contributor represents that, except as disclosed pursuant to Section 3.
APPENDIX 6.3. Derivative Works.
APPENDIX 10. U.S. GOVERNMENT END USERS. The Covered Code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of "commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June 1995), all U.S. Government End Users acquire Covered Code with only those rights set forth herein. 11. MISCELLANEOUS.
Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service. Model : Serial No.
