Specification

27 3/8”
(69.5 cm)
29 5/16”
(74.5 cm
)
w/o handle
24 1/2”
w handle
27”
29 3/4”
(75.5 cm)
23 3/8”
(59.3 cm)
28 7/8”
(73.3 cm)
27 3/8”
(69.5 cm)
29 5/16”
(74.5 cm)
w/o handle
24 1/2”
w handle
27”
29 3/4”
(75.5 cm)
23 3/8”
(59.3 cm)
28 7/8”
(73.3 cm)
© 2018 LG Electronics USA, Inc. All rights reserved. "LG Life’s Good" is a registered trademark of LG Corp. All other product and brand names are trademarks or registered trademarks of their respective owners. Design, features and specifications are subject to
change without notice. Non-metric weights and measurements are approximate. Some features may require Internet access. Content and services may vary by product and are subject to change without notice. 8/7/18
QUICK INSTALL & CLEARANCES
For full installation directions/clearances please refer to
the corresponding User Manual and Installation Guide.
IMPORTANT
LSWS307ST / LSWS300BD
4.7 cu. ft. Single Wall Oven
HOME APPLIANCES
LG STUDIO
DIMENSIONS/CLEARANCES
Product (W x H x D) 29-3/4" x 29-5/16" x 24-3/8"
Cut-out (W x H x D) 28-1/2" x 29" x 23-1/2"
Shipping Carton (W x H x D) 33" x 30" x 34"
POWER/RATINGS
Amp at 240V 4.1 KW
kW at 240V 120/240 VAC,120/208 VAC
Requirements 17.3A
IMPORTANT NOTES
PRODUCT DIMENSIONS
CUTOUT DIMENSIONS
The rst step of the installation is measure the
current cutout dimensions and compare them to the
cutout dimensions shown below. Little or no cabinet
work may be necessary.
(75.5 cm)
(59.3 cm)
Junction Box
Location
47”
8”
30”
23”
5”
28 1/2” Min.
28 5/8” Max.
51 13/16” Min.
51 15/16” Max.
Allow 1”
minimum for
overlap of oven
Allow 1”
minimum for
overlap of oven
23 1/2”
Minimum cutout location from or 12”
Conduit
66 15/16”
29-3/4”
23-1/2”
51-15/16”
•
Cabinet Width 29-3/4”
•
Recommended
Minimum Cutout 12”
Location from Floor
•
Cutout Depth 23-1/2”
•
Cutout Width 28- 1/2”
•
Cutout Height 51-15/16”
29-3/4”
29-5/16”
29-3/4”
29-5/16”
24-3/8”
•
The cabinet base platform must be able to support 190lbs (86kg). If the cabinet
does not have a solid bottom, two braces or runners must be installed level with
the bottom of the cutout to support the weight of the oven. Make sure the base
is level and the front of the cabinet is square. If the cabinet base is not level, the
oven glides will tend to slide out when opening the door.
•
If marks, blemishes or the cutout opening are visible above the installed oven, it
may be necessary to add wood shims under the runners and front trim until the
marks or opening are covered.
•
If the cabinet does not have a front frame and the sides are less than 3/4” (1.9
cm) thick, shim both sides equally to establish the cutout width.
•
The junction box must be ush with the rear wall of the cabinet as shown below.
•
Allow at least a 23” clearance for the door depth when it is open.
•
Kitchen cabinets in contact with the oven must be heat resistant up to 194°F
(90°C), and fronts of nearby units up to at least 158°F (70°C).