Install Manual

ENGLISH
9
Power on LED
FAULT LED
Place the spacer
In the line HERE
Place the spacer
In the line HERE
P
lace
the
spacer
In the line H
ER
E
P
lace
the
spacer
In the line
HERE
Place the
s
pac
er
In
t
he line
H
ER
E
Place the
s
pac
er
In
t
he line
H
ER
E
Place the spacer
In the line
HERE
Place the spacer
In the line
HERE
Handle
11. Check the operation of the battery
pack by following the steps below.
1) Hold and turn the handle
counterclockwise.
2) Open the front cover and turn on
the circuit breaker switch.
3) If there are no problems with the
assembly process or the product
itself, the LED power indicator will
turn on. Sixty (60) seconds later,
the LED fault indicator will blink
(due to a lack of communication
with the inverter, not due to a
product defect).
7XUQR൵WKH&LUFXLW%UHDNHUVZLWFK
Then, close the front cover and turn
the handle counterclockwise.
* If you experience any problems
at this stage, go to Section 5
Troubleshooting.
P
lac
e t
he spac
e
r
In the line HERE
P
lac
e t
he spac
e
r
In the line HERE
P
lac
e
the
spa
c
e
r
In the line HERE
P
lac
e
the
spa
c
e
r
In the line HERE
Place the spacer
In the li
ne HE
RE
Place the spacer
In the li
ne HE
RE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
12. Double-check the alignment of the
Battery Control Unit.
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
3 Remove a spacer
1 Grab
here
5 Remove another one in
the same way
4 Settle slowly
2 Lift (just few mm)
13. Remove one spacer by lifting one
side of the Battery Control Unit. After
that, remove the other spacer in the
same way.
* Be careful not to pull on the cables
by lifting the Battery Control Unit
too high. Doing so may cause
damage to the cables or cause the
unit to disconnect.
* Before setting down the Battery
Control Unit, the cable connection
should be checked once more.
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
14. Realign the Battery Control Unit.
Place
t
h
e
space
r
In
the
line HERE
Place
t
h
e
space
r
In
the
line HERE
Place
th
In
the l
i
ne
Place th
In
the l
ine
M5xL65 Flange Bolt
Top Cover
15. Loosen 4 bolts and remove the Top
Cover.
M5xL200 Flange long Bolt
16. 7LJKWHQVL[ORQJÀDQJHEROWVZLWK
a torque of 5N·m.
* While assembling, open the front
cover and check that all M5 Flange
long bolts are placed accordingly.
17. Move the Battery pack to set the right
position for assembly of the Standing
bracket.
Standing bracket_2
Standing bracket 2
18. Pre-tighten six (6) M6 bolts to
assemble the Standing Bracket 2 on
Battery Control Unit and the Standing
Bracket 1. After that, fully tighten all
bolts and fasteners on the Standing
Bracket 1 and the Standing Bracket 2.
* Tightening torque for the M6 bolts
is 5N·m.
Place the
spacer
In the line HERE
Place the
spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
pa
cer
RE
pacer
RE
19. Re-attach the top cover.
* Tighten the M5xL65 Flange Bolt
(4ea) with a torque of 5N·m.