Install Manual

8
Standing bracket_1
Standing bracket 1
3. Remove the Drill template. Then pre-
tighten the fasteners on the Standing
Bracket 1.
* The fasteners will be fully tightened
in a later step.
Battery Module B
Label
Wall
Rear
Front
Front
Rear
Battery Module Direction
4. Place Battery Module B on the rear
side of Module Connect plate.
* The side without bolts is the front
of the Battery Module.
* &KHFNWKHODEHOWRFRQ¿UPWKH
battery pack is of B. Label is
attached on the left side of Battery
Module.
Battery Module A
Label
Front
Front
Battery Module B
Battery Module A
TOP VIEW
Rear
Front
Wall
5. Place Battery Module A on the front
side of Module Connect plate. The
Rear side of each Battery Module
should face each other. After that,
remove the Spacer between the wall
and Battery Module.
* &KHFNWKHODEHOWRFRQ¿UPWKH
Battery pack is of A. Label is
attached on the left side of Battery
Module.
Module Support BRKT
6. Assemble Module Support BRKTs
using 6 bolts each.
* Tighten the M6 Flange Bolts (x12)
with a torque of 5N·m.
P
l
ace the spac
er
I
n the line HERE
Place t
h
e s
pacer
In the line HERE
Place t
h
e s
pacer
In
t
he
line HERE
Place th
e spacer
In the line H
ER
E
Place th
e spacer
In the line H
ER
E
P
l
ace the s
pac
er
In the
line HERE
P
l
ace the s
pac
er
In the
line HERE
Place t
h
e spacer
In the line HERE
Place t
h
e spacer
In the line HERE
Battery Control Unit
Battery Modules
7. Remove bubble wrap from
connectors of Battery Control Unit
and the warning label of Battery
Modules.
P
lace
t
h
e
spacer
In the line HERE
P
lace
t
h
e
spacer
In the line HERE
P
l
a
ce
th
e
spa
cer
I
n
the line H
E
R
E
P
l
a
ce
th
e
spa
cer
I
n
the line H
E
R
E
Place
the s
p
a
c
e
r
In the line HERE
Place
the s
p
a
c
e
r
In the line HERE
Plac
e t
he sp
a
c
er
I
n
th
e
li
ne
HE
R
E
Plac
e t
he sp
a
c
er
I
n
the
l
ine
HE
R
E
Spacer
(used for assmbly ang disassembly)
TOP
Place the spacer In the line HERE
Place the spacer In the line HERE
Pl
ace t
h
e spacer
I
n
t
h
e
lin
e
HER
E
Place the spacer In the line HERE
Place the spacer In the line HERE
Spacer
Spacer
TOP VIEW
8. Place the spacers on the position
marked with label on Battery
Modules.
Place the spacer
In the l
i
ne
HERE
Place the spacer
In the l
i
ne
HERE
Place the spacer
In
th
e li
ne HE
RE
Place the spacer
In
th
e li
ne HERE
Place
the
spa
cer
In
t
he
l
ine
HE
RE
Place
the
spa
cer
In
t
he line
HE
RE
Place the spacer
In th
e line H
E
RE
Place the spacer
In th
e line H
E
RE
Battery Control Unit
Battery Control Unit
Place the spacer
In the line H
ERE
Place the spacer
In the line HERE
Plac
e t
h
e space
r
In the li
ne HERE
Plac
e t
h
e space
r
In the li
ne HERE
Place the spacer
In the line HERE
Place the spacer
In t
h
e line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
9. Place the Battery Control Unit on
top of the spacers, and align with the
Battery Module.
* Be careful not to break the
connector between the spacers and
the Battery Control Unit.
Plac
e the spacer
In the line
HERE
Plac
e the spacer
In the line
HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In
the line HE
R
E
Place the spacer
In
the line HE
R
E
TPA
Sensing connector Power connector
Front
Front
Front
Front
Sensing connector Power connector
“Click!”
TPA
10. Connect the power and sensor
connectors on the right and left sides
(2 each). Assemble the connectors
until you hear a “Click”. After that,
lock the power connector by pressing
TPA (Terminal Position Assurance).