Install Manual

ENGLISH
7
3.1.5 Clearance
Ceiling
Floor
500 mm
(20")
300 mm
(12")
300 mm
(12")
 Recommended clearances for the left,
right and top of the product are shown in
WKH¿JXUHIRUWKHSURSHUYHQWLODWLRQDQG
installer convenience.
3.1.6 Tools & Safety Gear Required
 Tools
The following tools are required to install the battery pack :
Precision screwdriver M5 torque wrench Inclinometer
Drill
(min. diameter 10 mm, 0.4")
Pencil or marker Tape measure
7KHIDVWHQHUVDUHQHHGHGIRU¿[LQJWKHEUDFNHWRQWKHZDOO
 Safety Gear for Personal Protection
It is required to wear the following safety gears when handling the battery pack.
Insulated gloves Safety goggles Safety shoes
3.1.7 Appearance and Dimensions
 Appearance
Proper handling and care are recommended as disassembly, change of color,
VFUDWFKHVOHDNDJHRIOLTXLGDQGVWDLQVPD\LQÀXHQFHWKHHFRQRPLFYDOXHRIWKH
battery pack.
 Pack appearance and dimensions
1,086 mm
(42.8")
295 mm
(11.6")
504 mm
(19.8")
 Color and materials
- Battery Module front/rear case:
metallic gray, steel
- Battery Control Unit cover &
Module Connect Plate: metallic gray,
aluminum
- LED cover: black, plastic
3.1.8 System Clearance
7KHEDWWHU\UHTXLUHVDGHTXDWHFOHDUDQFHIRULQVWDOODWLRQFDEOLQJDQGDLUÀRZ7KHPLQLPXP
FOHDUDQFHIRUV\VWHPFRQ¿JXUDWLRQLVSURYLGHGEHORZ7KHFDEOHFRQQHFWLQJEHWZHHQEDWWHU\
pack and inverter should be in accordance with the installation guide manual of the inverter.
NOTE
An external DC isolator may be installed within the clearance zone. Minimum clearances
may be greater according to local regulations.
Inverter
Floor
500mm
(20”)
300mm
(12”)
300mm
(12”)
500mm
(20")
300mm
(12")
300mm
(12")
Inverter
Ceiling
Floor
3.1.9 Installing the Battery Pack
CAUTION
0DNHVXUHWKDWWKHLQYHUWHU$&DQG'&GLVFRQQHFWVDUHWXUQHGR൵EHIRUHFRQQHFWLQJWKH
power cable to the battery pack.
Install the battery pack through the following steps:
Wall
Area1
OK
OK
Ex) If min. clearance is 200mm,
305mm
203mm
Area2
Area2Area1
Ex) If min. clearance is 200 mm,
Wall
Ok
Ok
203 mm
305 mm
1. Place the Drill template to the wall
where the battery pack will be
installed. After that, drill holes on the
position marked on the Drill template.
* Recommended fastener count:
1(Area1)/1(Area2)
* Recommended fastener diameter/
length: 10mm/40mm Min.
* Fastener separation should observe
the regional building code.
Front
MODULE CONNECT
LATE 1
ୋ
Rear
Front
Wall direction
Front
Wall
direction
2. Place a spacer to the position marked
on the Drill template. After that, place
the Module connect plate in contact
with the Spacer and align center lines.
* Pay attention to the direction of
the Spacer. Refer to left image for
correct orientation.
* 'RQRWXVHDQFKRUEROWVWR¿[WKH
0RGXOHFRQQHFWSODWHWRWKHÀRRU
* Be careful not to damage the
aluminum foil attached on the
bottom of Module connect plate
during handling.