Install Manual

ENGLISH
17
6 Uninstallation & Return
6.1 Return/Replacement Instructions
6.1.1 Uninstallation
Uninstall the battery pack in the following order:
M5 PH Bolt 6ea
Front Protection Cover
1. Switch the inverter OFF before
beginning uninstallation of the battery
pack.
2. Switch circuit breaker OFF and make
sure it is in the OFF position.
3. Open the front cover, loosen 6 bolts
and remove the Front Protection
Cover.
4. Disconnect the cables.
Place the spacer
In the line HERE
Place the spacer
c
ce
c
ce
Pla
In the line HERE
HE
e
HE
ne
n
HE
he line HERE
he
t
he
5. Re-attach the Front Protection Cover
with M5 PH bolt 6ea.
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
M5xL65 Flange Bolt
Top Cover
6. Loosen 4 bolts and remove the Top
Cover.
7. Loosen six (6) M6 bolts and
disassemble Standing Bracket #2
ÀDW7KHQPRYHWKHEDWWHU\SDFN
R൵WKHZDOODQGUHPRYH6WDQGLQJ
Bracket #1 from the wall.
M5xL200 Flange
long Bolt
8. Loosen six (6) long bolts.
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place t
he
s
pacer
In the line
HERE
Place t
he
s
pacer
In the line
HERE
c
er
E
cer
E
9. Re-attach the top cover.
* Tighten the M5xL65 Flange Bolt
(4ea) with a torque of 5N·m.
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Battery Control Unit
Spacer
10. 3ODFHWKH¿UVWVSDFHURQWRSRIWKH
Battery Modules.
* Be careful not to pull the cables
tight by lifting the Battery Control
Unit excessively. It may damage the
cables or disassembly of connector.
P
l
ace the space
r
In the line HERE
P
l
ace the space
r
In the line H
ERE
Place the space
r
In the line HERE
Place the space
r
In the line HERE
Place the spacer
In the line HERE
Place the spacer
In the line HERE
Battery Control Unit
Spacer
11. After that, place the second spacer on
top of the Battery Modules.
P
lace the spacer
In the line HERE
P
lace the spacer
In the line HERE
P
lace the spacer
In the line HER
E
P
lace the spacer
In the line HER
E
Place the spacer
In the line HERE
Place the spacer
In the
line HERE
P
lace the spacer
In the line HERE
P
lace the spacer
In the line
HERE
1
2
3
1
2
3
Power connector
TPA
Sensing connector
Front
Front
12. Disconnect the power and sensor
connectors on the right and left sides
(2 each). This step should undergo
a deliberate visual inspection by the
installer before proceeding.
1) Power connector: 1 Pull the TPA
and 2 press the button at the
center of the connector. Then 3
pull out the connector vertically.
2) Sensor connector: 1 Push in the
sides of the connector and 2 pull
out the connector vertically. Then
3 pull the connector out to the
side of the Battery Module.
* Be careful of damage to the sensor
connector’s guide pins during
disassembly.
* At this stage, DO NOT lift the
Battery Control Unit until all
connectors are disassembled.