Installation Manual for RESU16H Prime LG Energy Solution strongly advises users to exercise due care in following LG Energy Solution’s product installation manual. Warranty claims are invalid if damage is caused by human error in a manner inconsistent with the installation manual’s instructions. Version 1.
The information included in this manual is accurate at the time of publication. However, this manual is subject to change without prior notice. In addition, the illustrations LQ WKLV PDQXDO DUH PHDQW RQO\ WR KHOS H[SODLQ V\VWHP FRQ¿JXUDWLRQ FRQFHSWV DQG LQVWDOODWLRQ instructions. Please note the images shown are for illustration purposes only. Contents 1 Safety 1.1 Symbols 1.2 Safety Instructions 1.2.1 General Safety Precautions 1.2.2 Battery Handling Guide 1.2.3 Response to Emergency Situations 1.
1 Safety 'R QRW VWHS RQ WKH SURGXFW RU WKH SURGXFWཚV SDFNDJLQJ VLQFH WKH SURGXFW PD\ EH damaged. 1.1 Symbols Do not put the battery pack upside down on the ground. Do not connect the power cables at terminal the block in the opposite direction.
1.3 2 Product Introduction Warning Label Product/warning label and Battery Control Unit’s traceability label are behind the front cover. The front cover opens by turning the front cover handle counterclockwise. Battery Modules’ traceability labels are attached to the side of the Battery Modules. 2.1 Technical Data 2.1.1 Dimensions and Weight RESU16H Prime Part Number 1 2-1 2-2 2-2 EH257064P8S1 Width 504 mm (19.8”) Height 1,086 mm (42.8”) Depth 295 mm (11.
2.3 Maintenance 1. Short Circuit Current/Duration 1.616 kA 0.44 ms RESU16H Prime does not require maintenance during normal operation if properly installed per the installation manual. In the event of fault, contact the regional service center. 3DFNDJLQJ 6SHFL¿FDWLRQV 2. Arc Flash Protection Calculations ,Q RUGHU WR SURWHFW SHUVRQQHO IURP WKH SRVVLELOLW\ RI JHWWLQJ LQMXUHG E\ DQ DUF ÀDVK KD]DUG $UF ÀDVK FDOFXODWLRQ RI WKH EDWWHU\ V\VWHP LV HVWLPDWHG ZLWK WKH ,QFLGHQW (QHUJ\ Calculations refer to
Basic lifting guide )ࢿۍ Prime 6H ߷ࡶ RESU1 ଗࡁ(ଗࡁ l for ࢉ Manua ࢉ؟ਫ਼ی tion Inverter: e Installa 4. Pull out the bundled items, including the Module Connecting Plate. ˁࡉ Refer to below guide for lifting and carrying the Battery Control Unit and Battery Modules during installation. Compatibl 3.1.2 Handling position Installer A 5. Pull out Battery Module B. Installer B B B 6. Pull out Battery Module A. Battery Control Unit 3.1.
Clearance 3.1.8 Recommended clearances for the left, right and top of the product are shown in WKH ¿ JXUH IRU WKH SURSHU YHQWLODWLRQ DQG installer convenience. Ceiling 500 mm (20") System Clearance 7KH EDWWHU\ UHTXLUHV DGHTXDWH FOHDUDQFH IRU LQVWDOODWLRQ FDEOLQJ DQG DLUÀ RZ 7KH PLQLPXP FOHDUDQFH IRU V\VWHP FRQ¿ JXUDWLRQ LV SURYLGHG EHORZ 7KH FDEOH FRQQHFWLQJ EHWZHHQ EDWWHU\ pack and inverter should be in accordance with the installation guide manual of the inverter. ENGLISH 3.1.
r Label Battery Modules Pl In ace th th e e lin sp e ac H er ER E Pl In ace th th e e lin sp e ac H er ER E nt Fro Rea 7. Remove bubble wrap from connectors of Battery Control Unit and the warning label of Battery Modules. Pl In ace th th e e lin sp e ac H er ER E 4. Place Battery Module B on the rear side of Module Connect plate. * The side without bolts is the front of the Battery Module. Battery Module B Battery Control Unit * &KHFN WKH ODEHO WR FRQ¿ UP WKH battery pack is of B.
11. Check the operation of the battery pack by following the steps below. 1) Hold and turn the handle counterclockwise. 15. Loosen 4 bolts and remove the Top Cover.
20. Open the front cover. * Hold the handle and turn it counterclockwise. 24. Connect the cables according to their application. * Refer to Section 3.3 Cable Connections. Pl In ace th th e e lin sp e ac HE er RE Pl In ace th th e e lin sp e ac HE er RE Pl In ace th th e e lin sp e ac HE er RE Pl In ace th th e e lin sp e ac HE er RE Handle Front Cover 25. Arrange the power cables and communication cables separately using cable ties. 21. Loosen 6 bolts and remove the Front Protection Cover.
,QVWDOODWLRQ SURFHVV IRU 5HPRWH 0RQLWRULQJ 'HYLFH 50' 3.2.1 3.2.1.3.1 Visit https://resumonitor.lgensol.com ENGLISH Remote monitoring device (RMD) is a remote device that can install and monitor a battery pack through App. and web. 3.2.1.3 User Registration Prepare for installation using RMD 3.2.1.1 Installer Sign In 3.2.1.1.1 Visit https://resumonitor.lgensol.com 1. Select the “Installer”option. 2. Enter your ID and Password. 3. Click the “Sign In” button. 1 2 3.2.1.3.
9. Select the “Owner” option. 3.2.2.3 User Agreement 10. Enter your ID and Password. 1. Search the product which you will install. 11. Click the “Sign In” button. 2. Get the agreement of privacy policy for the customer. 0 3. If the customer agrees the privacy policy, have customer’s personal information. ! 1 1 2 3 @ ,QVWDOODWLRQ YLD 50' &OLFN WKH OLQN RQ WKH 5(68 0RQLWRU ZHEVLWH WR GRZQORDG WKH $3. ¿ OH RI WKH µ5(68 ,QVWDOOHU¶ App.
3.2.2.6.2 Wi-Fi Connection The QR code scanning method is as follows. If you are using an ethernet connection and do not wish to use Wi-Fi, simply click the “Next” button. ENGLISH 3.2.2.5 QR Code Scan Select Prime: Fixed at 2 FLEX: Select from 2 to 4 S/N of consecutive QR codes are automatically displayed(Maximun 5) When the QR code registration is complete, click the “Next” button. If the scanned serial number matches the actual serial number, it will proceed to the next section.
6HUYHU &RQQHFWLRQ DQG %DWWHU\ 6WDWXV &KHFN 3.3 Cable Connections 3 1 2 IoT Hub Connection String: Enter the unique string provided to you in order to access the Azure IoT Hub (cloud server). The string format is as follows: HostName=emashub.azure-devices.net;DeviceId=XXXX;SharedAccessKey=OOOO= &DEOH &RQ¿ JXUDWLRQ * For more information on how to obtain strings, refer to Section 3.2.1.2 Obtaining IoT Hub String.
b) Connect the negative line of the power cable to Terminal 3. 1 2 3 4 Commissioning 4.1 LED Indicators The LED indicators on the front of the battery pack show its operational state as follows: c) Connect the positive line of the power cable to Terminal 1. ဵ 5HIHU WR 3.3.3 Spring Terminal Blocks when choosing the battery power cable and cable sheath for peeling. LED 1 3RZHU LED 2 &KDUJH LED 3 'LVFKDUJH LED 4 )DXOW Status Power on (lnit) ဵ :KHQ \RX LQVWDOO WZR SDFNV UHIHU WR WKH DSSHQGL[ DERXW S
5 Troubleshooting 5.1.2 Troubleshooting Guidelines If the battery LED power indicator is OFF 7URXEOHVKRRWLQJ 2YHUYLHZ 1. 7XUQ R൵ WKH FLUFXLW EUHDNHU Check the LED indicators on the front to determine the state of the battery pack. A fault state is triggered when certain conditions like voltage or temperature are beyond design limitations. The battery pack’s BMS periodically reports its operating state to the inverter.
6 Uninstallation & Return 6.1 Return/Replacement Instructions 6.1.1 ENGLISH 7. Loosen six (6) M6 bolts and disassemble Standing Bracket #2 À DW 7KHQ PRYH WKH EDWWHU\ SDFN R൵ WKH ZDOO DQG UHPRYH 6WDQGLQJ Bracket #1 from the wall. Uninstallation Uninstall the battery pack in the following order: 1. Switch the inverter OFF before beginning uninstallation of the battery pack. 8. Loosen six (6) long bolts. M5xL200 Flange long Bolt 2. Switch circuit breaker OFF and make sure it is in the OFF position.
13. Disassemble Module Support BRKTs with six (6) bolts each. * Loosen the M6 Flange Bolts (x12) 14. Repack in the box. 7. Appendix 7.1 Connection in RESU16H Prime parallel battery system CAUTION Parallel battery system can only be applied between products of the same energy. 6HWWLQJ IRU FRPPXQLFDWLRQ WHUPLQDWLRQ UHVLVWRU $ERXW 6HFWLRQ % 6.1.
7.2 RMD Applications %DWWHU\ 6WDWXV FKHFN YLD 50' How to check the battery status is as follows. Inverter Inverter ENABLE12V 12V ENABLE ENABLE GND ENABLE GND RS485A+ A+ RS485 RS485 RS485BBCANHi Hi CAN CANLo Lo CAN ENGLISH ENABLE 12V ENABLE 12V ENABLE GND ENABLE GND RS485 A+ RS485 A+ RS485 RS485BBCANHi Hi CAN CANLo Lo CAN 50' :L )L GLUHFW FRQQHFWLRQ First, proceed with RMD Wi-Fi direct connection as shown below.
Fault Name error code Over Voltage Fault2 DiagResultFault2 0x0001 Under Voltage Fault2 DiagResultFault2 0x0002 Over Temperature Fault2 Under Temperature Fault2 Over Charge Current Fault2 Over Discharge Current Fault2 Over Charge Power Limit Fault2 Over Discharge Power Limit Fault2 DiagResultFault2 0x0400 DiagResultFault2 0x0800 DiagResultFault2 0x0020 DiagResultFault2 0x0040 DiagResultFault2 0x0080 DiagResultFault2 0x0100 External Communication Failed (BMS-DC/DC LOC) DiagResultFault2 0x4000 In
,QVWDOODWLRQ YLD 50' IRU ZHE XVHU %06 '& '& DQG 50' 8SGDWH Can upgrade F/W. Upgrade is performed on the following three targets. - RMD 7.2.3.1 User Agreement ENGLISH Visit https://resumonitor.lgensol.com and Sign in. - BMS - DC/DC 1. &OLFN WKH µ&RQ¿ J¶ EXWWRQ 2. Click the ‘Update’ button 3. According to the target you want to update, click the 'Choose File' button. 1 2 4. 6HOHFW D XSGDWH ¿ OH 7 3 4 5 5. $IWHU FKHFNLQJ LI WKH ¿ OH LV VHOHFWHG correctly, click the 'Send' button.
%DWWHU\ ,QVWDOODWLRQ 50' 6HWXS 50' :HE /RJ LQ 1 2 4 Enter the password and click ‘Register’ to go to the home screen. The default password is set to 123456 and can be changed in the Web UI. 3 &RQ¿ J VHWWLQJ &OLFN ,QVWDOODWLRQ ĺ %DWWHU\ ,QVWDOODWLRQ DQG VHOHFW WKH GHYLFH WKH SUHSDUHG GHYLFH OLVW Search and access the SSID of the RMD AP from a device (hereinafter referred to as a device) supporting WLAN Station functions such as a smartphone. 1.
6HUYHU &RQQHFWLRQ :L )L VHWWLQJ ,I \RX KDYH DQ (WKHUQHW FRQQHFWLRQ DQG GRQ¶W ZDQW WR XVH :L¿ VNLS WKLV SDUW ENGLISH (QWHU WKH 1HWZRUN ĺ :L )L WDE 1. Click the Scan AP button on the top right of the Web UI. 2. The number of APs available is displayed in a pop-up window. 3. Select the AP to access from the SSID combo box, enter the password and click the Connect button(Manual input is possible). 4.
Keep this manual for later use. © 2021 LG Energy Solution ESS Battery Division PARC1, 108, Yeoui-daero, Yeongdeungpo-gu, Seoul, Republic of Korea, 07335 https://www.lghomebattery.com http://www.lgensol.
