For U.K. Customer CUSTOMER SERVICES P/No.:3828ER3038E : 0870-592-9929(Service Force) Mon.-Fri. 8:30AM - 5:30PM LGEUK SERVICE WEB-SITE : www.lgelectronics.co.
WD(M)-14310(5)FD WD(M)-14311(6)FD WD(M)-12310(5)FD WD(M)-12311(6)FD
P roduct Feature 추가선택, 예약, n Direct Drive System The advanced Brushless DC motor directly drives the drum without belt and pulley. n Water Circulation Spray detergent solution and water onto the load over and over. Clothes are soaked more quickly and thoroughly during wash cycle. The detergent suds can be removed more easily by the water shower during rinse cycle. The water circulation system uses both water and detergent more efficiently.
W arnings READ ALL INSTRUCTIONS BEFORE USE ! WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. IMPORTANT SAFETY INSTRUCTIONS WARNING : To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following: • Do not install or store the washer where it will be exposed to the weather.
S pecification 울 란제리 n Name : Front loading washing machine n Power supply : 220-240V~, 50Hz n Size : 600mm(W)×645mm(D)×850mm(H) n Weight : 64kg n Wash capacity/Max. Watt : 8kg(2100W) n Spin speed : No spin/400/800/1000/1200 [WD(M)-12310(5)FD/WD(M)-12311(6)FD] No spin/400/800/1000/1400 [WD(M)-14310(5)FD/WD(M)-14311(6)FD] n Water consumption : 64ℓ(8ℓ/Kg) ❋ The appearance and specifications may be varied without notice to raise the units quality.
I nstallation Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
I nstallation n Installation place requirement Level floor : Allowable slope under entire washer is 1˚ Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance. Additional Clearance : For wall, door and floor modeling is required. (10cm : rear /2cm:right & left side) Do not place or store laundry products on top of washer at any times. They can damage the finish or controls.
I nstallation n Electrical connection 1. Do not use an extension cord or double adapter. 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard. 3. Always unplug the machine and turn off the water supply after use. 4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible.
nstallation I n Normal Tap without thread & screw type inlet hose 1. Unscrew the fixing screw to attach the tap. 2. Push the connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws. 3. Push the water supply hose vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right. n Normal Tap without thread & one touch type inlet hose 1. Untighten the upper connector screw. 2.
I nstallation This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam) can be dangerous for children.
I nstallation n Level adjustment 1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. NOTE Timber or suspended type flooring may contribute to excessive vibration and unblance errors. 2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces of wood etc.
C are before washing n Before the first washing Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues from the drum that may have been left during manufacturing. n Caring before washing 1. Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. 2. Sorting To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
A dding detergent n Adding detergent and fabric softener 3. Detergent dosage max • If too much detergent is used more than the recommended amount, too many suds can occur and this will decrease the washing result or cause heavy load to the motor. (Causing a malfunction) MAX MAX MAX max • The detergent should be used according to the instruction of the detergent manufacture.
F unction n Recommended courses according to the laundry type Program Fabric Type Proper Temp. (Option) Cotton Color fast garments (shirts, night dresses, pajamas...)and lightly soiled white cotton (underwear...) 60˚C (Cold, 30˚C, 40˚C, 95˚C) Cotton-Eco Laundry type is the same in Cotton. Synthetic Polyamide, Acrylic, Polyester. 60˚C (40˚C) 40˚C (Cold, 30˚C,60˚C) Delicate Delicate laundry easily damaged. 30˚C (Cold, 40˚C) Wool/Silk Machine washable woolens with pure new wool only.
H ow to use washer 1. Cotton automatically selected upon power on. • Press the Power( ) button to start. • Press the Start/Pause( ) button. • Initial condition - Wash : Main wash - Rinse : 3 times - Spin : [WD(M)-14310(5)FD/WD(M)-14311(6)FD] 1400 rpm [WD(M)-12310(5)FD/WD(M)-12311(6)FD] 1200 rpm - Water temperature : 60˚C - Program : Cotton 14 2. Manual Selecting • Press the Power( ) button to start. • Select the conditions which you want to use, by pressing each button.
H ow to use washer (1) (2) (1) Button : Power (2) Dial : Program (3) Button : Start/Pause (4) Button : Option (3) (4) (5) (6) (5) Child lock (6) Button : Rinse (7) Button : Spin (8) Button : Temperature Power (7) (8) (9) (10) (11) (9) Button : Beeper (10) Button : Intensive (11) Button : Time Delay Program 1. Power • Press the Power( and off. (Program) ) button to turn power on • To cancel the Time Delay function, the Power( ) button should be pressed. 2.
H ow to use washer Start/Pause Option • By pressing the option button, only one option function be selected. 1. Start • This Start/Pause button is used to start wash cycle or pause the wash cycle. 2. Pause 1. Bio • If temporary stop of wash cycle is needed, press “Start/Pause” button. • When in Pause, the power is turned off automatically after 4 minutes. • If you want to eliminate protein stains(milk, blood, chocolate...), you may select Bio function by pressing the option button.
H ow to use washer Child lock Rinse • By pressing the Rinse button, the Rinse type can be selected. - Normal - Rinse+ - Rinse++ - Normal+Hold - Rinse++Hold If you choose to lock the buttons on the control assembly to prevent tampering, this function may be selected. 1. Child lock • Child lock can be set by pressing and holding the Option and Rinse button simultaneously. (About three seconds) 1.
H ow to use washer Time Delay Spin • By pressing the Spin button, the spin speed can be chosen. 2 1. Time Delay Preparing washing before starting “Time Delay” - Turn on the water tap. - Load laundry and close the door. - Place the detergent and fabric softener in the drawer. • How to set “Time Delay” - Press Power( ) button. - Turn the Program dial to select the program you require. - Press Time Delay button and set the desired time. - Press the Start/Pause( ) button.
H ow to use washer Water Temp. • By pressing the Temp. button, the water temperature can be selected. - Cold - 30˚C / 40˚C / 60˚C / 95˚C 1. Water Temperature • Water temperature can be selected as below according to the program. - Cotton-Eco 40˚C-60˚C - Cotton Cold-30˚C-40˚C-60˚C-95˚C - Synthetic Cold-30˚C-40˚C-60˚C - Delicate & Wool/Silk & Quick 30 & Hand Wash & Duvet Cold-30˚C-40˚C The required temperature lamp will light up for identification.
H ow to use washer Display 3. Completion of washing • When washing cycle is completed, “ ” is displayed on the “Multi display”. 1. Special function display 4. Time left • When Child lock is selected, the “ ” lamp is on. • During washing cycle, the remaining washing time is displayed. • When time delay is selected, it shows the remaining times to finish the selected program. • Recommended program by manufacturer. - Cotton : around 1 hour and 53 minutes - Cotton-Eco : around 2 hours and 3 minutes 2.
M aintenance ❋ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. ❋ When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. n The water inlet filter -" " error message will blink on the control panel when water does not enter the detergent drawer.
M aintenance n Dispenser drawer ❋ After a while detergents and fabric softeners leave a deposit in the drawer. MAX MAX • It should be cleaned from time to time with a jet of running water. • If necessary it can be removed completely from the machine by pressing the catch downward and by pulling it out. • To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
M aintenance n The water circulation nozzle • Clean the water circulation nozzle, if clogged. n Cleaning your washer 1. Exterior Proper care of your washer can extend its life. The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with sharp objects. ❋ IMPORTANT: Do not use methylated spirits, diluents or similar products. 2.
T roubleshooting guide ❋ This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately. When the machine does not function properly or does not function at all, check the following points before you contact your service provider. Symptom Possible Cause Solution Rattling and clanking noise • Foreign objects such as coins or safety pins maybe in drum or pump. Stop washer and check drum and drain filter.
T roubleshooting guide Symptom Washer does not start Possible Cause • Electrical power cord may not be plugged in or connection may be loose. Make sure plug fits tightly in wall outlet. • House fuse blown, circuit breaker tripped,or a power outage has occurred. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If problem is a circuit overload, have it corrected by a qualified electrician. Turn on water supply tap. • Water supply tap is not turned on.
T roubleshooting guide Symptom Possible Cause Solution • Water supply is not adequate in area • Water supply taps are not completely open. • Water inlet hose(s) are kinked. • The filter of the inlet hose(s) are clogged. • If water leakage occured in the inlet hose, indicator “ ” will be changed red color. [WD(M)-14310(5)FD/WD(M)-12310(5)FD] Check another tap in the house. • Drain hose is kinked or clogged. • The drain filter is clogged. Clean and straighten the drain hose.
T erms of Warranty What Is Not Covered: • Service trips to your home to teach you how to use the product. • If the product is connected to any voltage other than that shown on the rating plate. • If the fault is caused by accident, neglect, misuse or Act of God. • If the fault is caused by factors other than normal domestic use or use in accordance with the owner's manual. • Provide instruction on use of product or change the set-up of the product.
