Visit us at : http://www.lgservice.com LG Deluxe Wired Remote Controller For Split Duct Owner's & Installation Manual Models: PDRCUDB0 PDRCUDB0B PDRCUDB0S IMPORTANT • Please read this manual completely before installing the product. • Installation work must be performed in accordance with the national wiring standards by authorized personnel only. • Please retain this installation manual for future reference after reading it thoroughly.
Deluxe wired remote controller Owner’s & Installation Manual TABLE OF CONTENTS ■ Safety precautions ............................................................3~4 ■ Part description .................................................................5~6 • Deluxe wired remote controller.............................................................6 ■ Deluxe wired remote controller switch information ...........7 ■ Installation method ...............................................................
Safety Precautions Safety Precautions WARNING This symbol indicates the possibility of death or serious injury. CAUTION This symbol indicates the possibility of injury or damage. ■ Meanings of symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. WARNING ■ Installation Be sure to request to the service center or installation specialty store when installing products. • It will cause fire or electric shock or explosion or injury.
Safety Precautions Request to the service center or installation specialty store when the product becomes wet. • It will cause fire or electric shock. Do not give the shock using sharp and pointed objects. • It will cause breakdown by damaging parts. CAUTION ■ In-use Do not clean using the powerful detergent like solvent but use soft cloths. • It will cause fire or product deformation. Do not press the screen using powerful pressure or select two buttons.
Part Description Part Description 2. LCD screen 3. Connecting cable and connector AUTO INDOOR ZONE 1 ZONE 2 REMO ZONE 3 AUTO INDOOR ZONE 1 ZONE 2 REMO ZONE 3 ZONE 4 2TH ZONE 4 Accessory Connecting cable (1EA) Fixing screw (2EA) Owner / Installation Manual Installation paper Owner’s & Installation Manual 5 ENGLISH 1.
Part Description Deluxe wired remote controller 1. Operation display panel 12. On/Off button 2. Room temperature button 13. Special function button 3. Fan speed button 14. Dehumidification/ Heater/ Child lock button 4. Fan/ Plasma/ Zone1 button 5. Auto/ Indoor/ Zone2 button 6. Timer mode button 7. Date selection button 8. Hour/Minute button 9. Mode selection button 10. On/Off button for reservation 15. Sub function button 16. Easy reservation button 17. Cancel button 18.
Deluxe wired remote controller switch information Deluxe wired remote controller switch information S/W 1. C/O Product 2. H/P Product • On installing, don't impact to the PCB and LCD display 1 2 • Don't remove the caution label. Zone type selection • Use the specified screw 1 1. Zone New 2 2. Zone Old • On installing, turn off the main power S/W 1 Ceiling height / E.S.P Group control S/W GR S/W 2 1 2 3 1. Low / Low 2. Standard / High 3. High / High 1 2 1. Master 2. Slave *E.S.
Installation Method Installation Method 1 Put the installation paper on the place and determine the position and height of the fixing screws of the deluxe wired remote controller. • Refer to the printed side of the installation paper. The position of the fixing screws Side of remote Controller 3 CN-DISP IC01A LO1K J14 C01K LO1D C07D CN-M C CN-ZONE Main frame J15 • The product is being shipped with the cable connected only to the remote controller.
Installation Method Group Control • If it is not event communication indoor unit, set the unit as slave. • Check for event communication through the product manual. • Refer to regarding page on how to set the slave. ENGLISH 1. When installing more than 2 units of air conditioner to one deluxe wired remote controller, please connect as the right figure. GND Signal wire 12V 2. When installing more than 2 deluxe wired remote controllers to one air conditioner, please connect as the right picture.
Installation Instruction Installation Instruction Installer Setting - Test Run Mode The Test Run Mode is to check the installation status of the product. The temperature will not be controlled during trial operation. Instead the product will operate in several modes such as cooling, strong wind, comp-on. AUTO INDOOR ZONE 1 ZONE 3 AUTO INDOOR ZONE 2 The test run mode is to check the installation status of the product. The temperature will not be controlled.
Installation Instruction Installer Setting - Setting the Cental Control Address Group No. Indoor No. ZONE 1 ZONE 2 AUTO INDOOR ZONE 1 ZONE 2 REMO ZONE 3 REMO ZONE 3 Press the 2 Press the button. Press the button to change the group number. Press the button to change the indoor unit number. In the figure on the left, the number of the central control address group is "2." and the number of the indoor unit is "5." 3 If you press the value will be set. ZONE 4 button.
Installation Instruction Installer Setting - ESP Function E.S.P function is setting the volume of each air flow. It is for the convenience of installation. It is recommended that you should not use this function while using the wireless remote controller. CAUTION If you set ESP incorrectly, the air conditioner may malfunction. This setting must be carried out by a certificated-technician.
Owner's Instruction Owner's Instruction Cooling Mode ZONE 2 ZONE 2 2 Press the button and set the expected temperature lower than the current room temperature. (18~30°C) button. REMO ZONE 3 REMO ZONE 1 Cooling mode will begin if you press the ZONE 3 ZONE 4 2TH ZONE 4 A click of the button will increase the expected temperature by 1°C A click of the button will decrease the expected temperature by 1°C.
Owner's Instruction Heating Mode AUTO INDOOR ZONE 1 ZONE 2 ZONE 2 Press the 2 Set the expected room temperature higher than the current room temperature. (16~30°C) button and then press the button. REMO ZONE 3 REMO ZONE 1 1 ZONE 3 ZONE 4 2TH ZONE 4 A click of the button will increase the expected temperature by 1°C A click of the button will decrease the expected temperature by 1°C.
Owner's Instruction Auto Changeover Mode Press the button and then press the AUTO button. AUTO AUTO INDOOR ZONE 1 ZONE 2 REMO ZONE 3 REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 2 When the expected temperature is lower than the room temperature : Cooling Mode. When the expected temperature is higher than the room temperature : Heating Mode 3 Press the 2TH ZONE 4 among button and choose one of the functions , , , and if you want anotheroperation mode during the operation.
Owner's Instruction Dehumidification Mode Dehumidification operation: Dehumidification by lowering temperature slightly AUTO INDOOR ZONE 1 ZONE 2 ZONE 2 Press the 2 Select the dehumidification function by pressing the button and the button. 3 When the dehumidification is being done, ”dh” will be shown on the display panel 4 Press the button on the remote controller.
Owner's Instruction Fan Mode ZONE 2 ZONE 2 2 Select the fan function by pressing the and button. 3 When the fan is being done, "Fn" will be displayed on the display panel. 4 Press the button on the remote controller. REMO ZONE 3 REMO ZONE 1 Press the ZONE 3 ZONE 4 button 2TH ZONE 4 among AUTO button and choose one of the functions , , , and if you want another operation mode during the operation. AUTO • When fan mode is operated, the outdoor compressor doesn't work.
Owner's Instruction Fan Speed Selection You can easily control the fan speed. 1 AUTO INDOOR ZONE 1 ZONE 2 REMO ZONE 3 REMO ZONE 1 ZONE 2 Select the proper fan speed which you want by pressing the button on the remote controller. ZONE 3 ZONE 4 2TH ZONE 4 • If you press the button, the strength of the fan speed will change in the order of Low → Med →Hi . • If the product is not compatible with the fan speed control, it will not function as your selection.
Sub Function Sub Function Thermistor Press the 2 Set thermistor mode by pressing button. Selected button INDOOR REMO 2TH ENGLISH 1 button on the remote controller. INDOOR , REMO , 2TH Function Operation in indoor unti temperature sensor. Operation in remote controller temperature sensor. Operation in lower temperature after comparing the temperature between the indoor unit and remote controller. * System will use value that sensed indoor unit or remote controller.
Sub Function Plasma You can use the plasma function. AUTO INDOOR ZONE 1 ZONE 2 ZONE 2 Press the 2 Press button. REMO ZONE 3 REMO ZONE 1 1 ZONE 3 ZONE 4 button. 2TH ZONE 4 • A click of the button will turn on/off the indicator. • If the product is not compatible with the plasma function, it will not do the plasma function even though the indicator is turned on. • Plasma function is possible when only product is installed.
Special Function Special Function This is a function to prevent tampering of settings by children or others. AUTO INDOOR ZONE 1 ZONE 2 ZONE 2 Press the 2 Press button of the remote controller. REMO ZONE 3 REMO ZONE 1 1 ZONE 3 ZONE 4 button. 2TH ZONE 4 • A click of the child lock button will turn on/off the indicator.
Special Function Zone control function You can control zones when you've installed the zone controller new type. 1 Press ZONE 1 , ZONE 2 , ZONE 1 AUTO INDOOR ZONE 1 ZONE 2 ZONE 2 . ZONE 4 ZONE 2 button. ZONE 3 ZONE 4 REMO ZONE 3 REMO ZONE 1 ZONE 3 ZONE 3 ZONE 4 2TH • A click of the desired zone will turn on/off it's indicator.
Special Function Simple Reservation ZONE 2 REMO ZONE 3 REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 2TH ZONE 4 Press button on the remote controller. 2 Press easy 3 You can change the values by pressing the control buttons. Choose a desired reservation time. button.
Special Function Setting the current time AUTO INDOOR ZONE 1 ZONE 2 ZONE 2 You can set the current time by pressing the time display. When the time display is selected, a window for date and time setting shows up. 2 Press the 3 If you press the REMO ZONE 3 REMO ZONE 1 1 ZONE 3 ZONE 4 2TH ZONE 4 If you press the button, the day of the week will flash. Then you can choose the proper day in the order of Monday, Tuesday, Wednesday, Thursday, Friday, Saturday and Sunday.
Special Function Weekday reservation AUTO INDOOR ZONE 1 ZONE 2 REMO ZONE 3 REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 1 Press the controller. 2 Select the day of week to set using the 3 After pressing the button on the control panel of the remote button. 2TH ZONE 4 button decide the time to turn off the air conditioner using the button. If the off icon blinks for a while and then stops on the time display panel, it is successfully set.
Special Function Different Mode Operation When one outdoor unit have several indoor units, different mode operation is which each indoor unit operate different mode.
P/No.: 3828A20561Y Printed in Korea After reading this manual, keep it in a place easily accessible to the user for future reference.
