website http://www.lgservice.com OWNER'S MANUAL Prior to installation, this air-conditioning unit must be submitted for approval by the utility service which provides electricity (EN 61000-2, 61000-3 Norm). êìëëäàâ üáõä ITALIANO LG Floor Standing-Type Air Conditioner ENGLISH ENGLISH LG ESPAÑOL FRANÇAIS DEUTSCH IMPORTANT • Please read this owner's manual carefully and thoroughly before installing and operating your air conditioner.
Floor Standing- Type Air Conditioner Owner’s Manual TABLE OF CONTENTS FOR YOUR RECORDS Safety Precautions.................3 Write the model and serial numbers here: Model # Serial # Operating Instructions...........8 You can find them on a label on the side of each unit. Dealer's Name Date Purchased Maintenance and Service ....25 ■ Staple your receipt to this page in the event you need it to prove date of purchase or for warranty issues.
Safety Precautions Safety Precautions WARNING This symbol indicates the possibility of death or serious injury. CAUTION This symbol indicates the possibility of injury or damage. ■ Meanings of symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. WARNING ■ Installation Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit. • There is risk of fire or electric shock.
Safety Precautions Do not modify or extend the power cable. • There is risk of fire or electric shock. For installation, always contact the dealer or an Authorized Service Center. • There is risk of fire, electric shock, explosion, or injury. Do not install, remove, or reinstall the unit by yourself (customer). • There is risk of fire, electric shock, explosion, or injury. Do not install the product on a defective installation stand. • It may cause injury, accident, or damage to the product.
Safety Precautions Do not allow water to run into electric parts. • There is risk of fire or failure of product. Do not use the product in a tightly closed space for a long time. • Oxygen deficiency could occur. ENGLISH • It may cause There is risk of fire, failure of the product, or electric shock. Do not store or use flammable gas or combustibles near the product. Gasolin When flammable gas leaks, turn off the gas and open a window for ventilation before turn the product on.
Safety Precautions When the product is not be used for a long time, disconnect the power supply plug or turn off the breaker. • There is risk of product damage or failure, or unintended operation. Take care to ensure that nobody could step on or fall onto the outdoor unit. • This could result in personal injury and product damage. CAUTION ■ Installation Always check for gas (refrigerant) leakage after installation or repair of product. • Low refrigerant levels may cause failure of product.
Safety Precautions Use a soft cloth to clean. Do not use harsh detergents, solvents, etc. • It may cause product failure. • There is risk of fire, electric shock, or damage to the plastic parts of the product. Do not touch the metal parts of the product when removing the air filter. They are very sharp! • There is risk of personal injury. ENGLISH Do not block the inlet or outlet of air flow. x Wa Thinner Do not step on or put anyting on the product. (outdoor units) Always insert the filter securely.
Operating Instructions Operating Instructions Features and Specifications 1. Design for cooling and heating 6. 2 cooling/heating speeds 2. Super energy efficiency 7. Removable air filter 3. Micom control 8. Anti-Bacteria filter 4. Whisper quiet operation 9. 3 minutes delay circuit 5.
Operating Instructions Indoor Unit Controls and Indicators 8 9 7 6 14 5 2 1 A/CL 13 10 (Z, TA* Model) 8 9 7 6 13 10 (H/P, TC* Model) 8 9 7 4 12 14 12 6 5 3 2 4 1 3 2 1 A/CL 13 10 (H/P, TA* Model) 8 9 7 6 13 10 (C/O, TC* Model) 8 11 12 7 4 3 2 12 6 4 1 3 2 1 A/CL 13 (C/O, TA* Model) ❈ NOTE 8 11 7 12 6 13 4 3 2 12 4 1 3 Z : HEAT PUMP +HEATER H/P : HEAT PUMP C/O : COOLING ONLY Owner's Manual 9 ENGLISH (Z, TC* Model)
Operating Instructions Indoor Unit Controls and Indicators 1. START/STOP BUTTON Operation starts when this button is pressed and stops when the button is pressed again. 2. OPERATION MODE SELECTION BUTTON 10. DEFROST OPERATION LAMP 11. AUTO OPERATION LAMP 12. OFF TIMER OPERATION LAMP 13. OUTDOOR UNIT OPERATION LAMP Used to select the operation Mode. 3. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4. INDOOR FAN SPEED SELECTION Used to select fan speed in two steps-low, med. 5.
Operating Instructions Remote-Controller for MODEL 18 2 18 2 4 12 4 13 10 7 14 A/CL 13 10 7 14 11 8 15 17 15 17 3 6 3 6 5 (Z,H/P, TC* Model) (Z,H/P, TA* Model) 1 2 2 4 12 4 9 11 14 13 9 7 14 A/CL 13 7 8 15 17 15 16 3 6 3 6 5 (C/O, TC* Model) (C/O, TA* Model) Owner's Manual 11 ENGLISH 1
Operating Instructions Name and Function-Remote Control 1. Signal Transmitter • Transmits the signals to the floor standing type air conditioner 2. Operation Display of the Remote Control 3. Indoor Fan Speed Selection Button • To select the desired fan speed in two steps [Low, Mid] 4. Cooling ON Button 5. Temperature Setting Buttons 6. Power ON/OFF Button • Operation will start when this button is pressed, and stop when the button is pressed again. 7.
Operating Instructions Remote Control Preparation ENGLISH 1. How to mount onto a wall Use the screws to secure the holder to the wall or attach the holder side of indoor unit. 2. To insert the remote control to the holder. Insert Pull How to insert batteries 1. Remove the cover from the back of the remote controller. • Slide the cover according to the arrow direction. • Do not use rechargeable batteries such batteries as different from standard dry cells in shape, dimensions, and performance. 2.
Operating Instructions How to use the Operation Mode Button • Each time the Operation Mode Selection Button is pressed, the Operation Mode is shifted in the arrow direction. Cooling Operation Soft Dry Operation Heating Operation (Heat pump Model) Cooling Operation Auto Operation Soft Dry Operation (Cooling Model) How to use the Fan speed Button • Each time the Fan speed Button is pressed, the Fan speed is shifted in the arrow direction.
Operating Instructions Cooling Operation Mode 2 ENGLISH 1 Press the Start/Stop Button. Select Cooling Operation. Press the Operation Mode Selection Button. Press the Cooling Operation Button on the remote controller. A/CL 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature 4 Set the Fan Speed.
Operating Instructions Soft Dry Operation 1 2 Press the Start/Stop Button. Select Soft Dry Operation. Press the Operation Mode Selection Button. Press the Soft Dry Operation Button on the remote controller. A/CL 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature During softy Dry Operation • The indoor fan speed is automatically set to low and can be set fan speed.
Operating Instructions Heating Operation Mode(Heat Pump Model) 2 ENGLISH 1 Press the Start/Stop Button. Select heating Operation. Press the Operation Mode Selection Button. Press the heating Operation Button on the remote controller. A/CL 3 Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature 4 Set the Fan Speed. ❑ Each time the Button is pressed, the Fan Speed mode is shifted.
Operating Instructions Auto Operation Mode(Cooling Model Only) 1 2 Press the Start/Stop Button. Select Auto Operation. Press the Operation Mode Selection Button. Press Auto Operation Button on the remote controller. A/CL 3 Set the temperature upper or lower than the standard temperature. The temperature can be set within a range of by 1 level. Cold Cool Proper Warm Hot (This indication will be shifted to the initial Auto Mode Display state after 4 seconds.) To raise the temperature.
Operating Instructions Electric Heater Operation Mode(Heat pump & Electric heater product only) 2 ENGLISH 1 Press the Start/Stop Button. Select heating Operation by pressing the Opertion Mode Selection button. Press the Heater Operation Button on the remote controller. A/CL A/CL HEATER 3 Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature 4 Set the Fan Speed.
Operating Instructions OFF Timer Setting Procedure(OFF TIMER Setting, or CANCEL) 1 Press the Start/Stop Button. 2 Select Function. 3 Press the Timer Button. A/CL • If you press the button, the selected off timer is displayed as follows; • If you select ‘ ’, the Off Timer function will be cancelled. 4 When you finish the Off Timer setting, the Timer indicator lights off. After 4 seconds 5 During off-timer operation if you press the Timer Button, the rest time will be displayed.
Operating Instructions Plasma Air Purifying Operation Procedure(TC* MODEL) Air Purifying Operation only 1 Press the Plasma Air Purifying Operation Start/Stop Button. ENGLISH 1 A/CL (Operation will start when the button is pressed, and stop when the button is pressed again.) 2 Select Fan speed. The display shows low fan speed at the initial condition. Low Mid • You can operate the Plasma Air Purifying under the unit operation of cooling, heating, soft dry or Auto mode.
Operating Instructions Fan Operation Mode(TA* MODEL) 1 Press the Start/Stop Button. 3 Set the Fan Speed. 2 Press Fan Operation Button. MODE ❑ Each time the Button is pressed, the Fan Speed mode is shifted. Airflow Direction Procedure 1 Press the Start/Stop Button. Press the Auto Swing Button and then left and right. 2 louvers will swing Press the Airflow Direction Control Button again to set the Vertical louver at the desired airflow direction.
Operating Instructions Jet Cool Operation ENGLISH 1 Press the Start/Stop Button. On/Off 2 Press the Jet Cool button to operate the speed cooling mode and the unit will operate in high fan speed on cooling mode. (Z,H/P Model) 3 (C/O Model) To cancel the Jet Cool mode, press the Jet Cool button again or the fan speed button or the room temperature setting button and the unit will operate in mid fan speed on cooling mode.
Operating Instructions Child Lock Operation Procedure 1 Press the fan speed button and High temperature setting buttons simultaneously for 3 seconds. The unit will respond with beep. After 3 second, it will shift 2 After 3 seconds, it will shift During Child Lock Operation ➊ Whenever you press any Button on Display Panel, it will immediately display “ ”, which means Display panel is Locked. ❷ All the Button on the indoor unit Display panel will not work.
Maintenance and Service Maintenance and Service CAUTION: Before performing any maintenance, turn off the main power to the system. Cleaning of the air filters. Recommended about once every two weeks Cleaning of the air cleaner. Recommended about once every three months Remove the Air Filter. Take hold of the tab and pull slightly forward to remove the filter. Remove the Air Cleaner. Take hold of the tab and pull slightly forward to remove the air cleaner. Clean.
Maintenance and Service Troubleshooting Check the following points before requesting repairs or service.... If the malfunction persist, please contact your dealer. Case Does not operate. Explanation See page • Have you made a mistake in timer operation? • Has the fuse blown or has the circuit breaker been tripped? • Is the power Switch at Off? • Is the unit at the starting of Heating Operation? If yes, Hot-start is activating. • Is the unit in the Deicing? If yes, wait for finishing the Deicing.
ëÓÍ ÒÎÛÊ·˚ ‰‡ÌÌÓ„Ó ÚÓ‚‡‡-7 ÎÂÚ ÒÓ ‰Ìfl Ô‰‡˜Ë ÚÓ‚‡‡ ÔÓÚ·ËÚÂβ. P/No.
