ENGLISH ITALIANO ESPAÑOL FRANÇAIS DEUTSCH OWNER’S MANUAL AIR CONDITIONER Please read this manual carefully before operating your set and retain it for future reference. TYPE : FLOOR STANDING The equipment complies with requirements of the Technical Regulation, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment. P/NO : 3828A30069N www.lg.
Floor Standing- Type Air Conditioner Ownerʼs Manual TABLE OF CONTENTS FOR YOUR RECORDS Safety Precautions.................3 Write the model and serial numbers here: Model # Serial # Operating Instructions...........6 You can find them on a label on the side of each unit. Dealer's Name Date Purchased Maintenance and Service ....19 n Staple your receipt to this page in the event you need it to prove date of purchase or for warranty issues.
Safety Precautions To prevent injury to the user or other people and property damage, the following instructions must be followed. n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. WARNING This symbol indicates the possibility of death or serious injury. CAUTION This symbol indicates the possibility of injury or damage. n Meanings of symbols used in this manual are as shown below. Be sure not to do.
Safety Precautions For installation, always contact the dealer or an Authorized Service Center. • There is risk of fire, electric shock, explosion, or injury. Do not install the product on a defective installation stand. • It may cause injury, accident, or damage to the product. Be sure the installation area does not deteriorate with age. • If the base collapses, the air conditioner could fall with it, causing property damage, product failure, and personal injury.
Safety Precautions n Installation Always check for gas (refrigerant) leakage after installation or repair of product. • Low refrigerant levels may cause failure of product. Do not install the product where the noise or hot air from the outdoor unit could damage the neighborhoods. • It may cause a problem for your neighbors. Install the drain hose to ensure that water is drained away properly. • A bad connection may cause water leakage. Use two or more people to lift and transport the product.
Operating Instructions Operating Instructions Features and Specifications 1. Design for cooling and heating 6. 2 cooling/heating speeds 2. Super energy efficiency 7. Removable air filter 3. Micom control 8. Anti-Bacteria filter 4. Whisper quiet operation 9. 3 minutes delay circuit 5.
Operating Instructions ENGLISH Indoor Unit Controls and Indicators 7 8 6 5 15 2 1 A/CL 14 9 (Heat Pump Model) 7 10 6 5 11 12 4 3 2 1 A/CL 14 13 11 4 3 (Cooling Model) 1. START/STOP BUTTON Operation starts when this button is pressed and stops when the button is pressed again. 2. OPERATION MODE SELECTION BUTTON Used to select the operation Mode. 3. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4.
Operating Instructions Name and Function-Remote Control 1 16 2 1. Signal Transmitter • Transmits the signals to the floor standing type air conditioner 2. Operation Display of the Remote Control 4 11 A/CL 3. Indoor Fan Speed Selection Button • To select the desired fan speed in two steps [Low, Mid] 12 10 7 13 5. Temperature Setting Buttons 8 6. Power ON/OFF Button • Operation will start when this button is pressed, and stop when the button is pressed again. 14 17 3 6 7.
Operating Instructions ENGLISH Remote Control Preparation 1. How to mount onto a wall Use the screws to secure the holder to the wall or attach the holder side of indoor unit. 2. To insert the remote control to the holder. Insert Pull How to insert batteries 1. Remove the cover from the back of the remote controller. • Slide the cover according to the arrow direction. • Do not use rechargeable batteries such batteries as different from standard dry cells in shape, dimensions, and performance. 2.
Operating Instructions How to use the Operation Mode Button • Each time the Operation Mode Selection Button is pressed, the Operation Mode is shifted in the arrow direction. Cooling Operation Soft Dry Operation Heating Operation (Heat pump Model) Cooling Operation Auto Operation Soft Dry Operation (Cooling Model) How to use the Fan speed Button • Each time the Fan speed Button is pressed, the Fan speed is shifted in the arrow direction.
Operating Instructions ENGLISH Cooling Operation Mode 1 2 Press the Start/Stop Button. Select Cooling Operation. Press the Operation Mode Selection Button. Press the Cooling Operation Button on the remote controller. A/CL 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature 4 Set the Fan Speed.
Operating Instructions Soft Dry Operation 1 2 Press the Start/Stop Button. Select Soft Dry Operation. Press the Operation Mode Selection Button. Press the Soft Dry Operation Button on the remote controller. A/CL 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature During softy Dry Operation • The indoor fan speed is automatically set to low and can be set fan speed.
Operating Instructions ENGLISH Heating Operation Mode(Heat Pump Model) 1 2 Press the Start/Stop Button. Select heating Operation. Press the Operation Mode Selection Button. Press the heating Operation Button on the remote controller. A/CL 3 Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature 4 Set the Fan Speed. q Each time the Button is pressed, the Fan Speed mode is shifted.
Operating Instructions Auto Operation Mode(Cooling Model Only) 1 2 Press the Start/Stop Button. Select Auto Operation. Press the Operation Mode Selection Button. Press Auto Operation Button. A/CL 3 Set the temperature upper or lower than the standard temperature. The temperature can be set within a range of by 1 level. Cold Cool Proper Warm Hot (This indication will be shifted to the initial Auto Mode Display state after 4 seconds.) To raise the temperature.
Operating Instructions ENGLISH Electric Heater Operation Mode(Heat pump & Electric heater product only) 1 2 Press the Start/Stop Button. Select heating Operation by pressing the Opertion Mode Selection button. Press the Heater Operation Button on the remote controller. A/CL 3 Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature 4 Set the Fan Speed.
Operating Instructions OFF Timer Setting Procedure(OFF TIMER Setting, or CANCEL) 1 2 3 Press the Start/Stop Button. Select Function. Press the Timer Button. A/CL • If you press the button, the selected off timer is displayed as follows; • If you select ‘ ’, the Off Timer function will be cancelled. 4 When you finish the Off Timer setting, the Timer indicator lights off. After 4 seconds 5 During off-timer operation if you press the Timer Button, the rest time will be displayed.
Operating Instructions ENGLISH Plasma Air Purifying Operation Procedure 1 Air Purifying Operation only 1 Press the Plasma Air Purifying Operation Start/Stop Button. A/CL (Operation will start when the button is pressed, and stop when the button is pressed again.) 2 Select Fan speed. The display shows low fan speed at the initial condition. Low Mid • You can operate the Plasma Air Purifying under the unit operation of cooling, heating, soft dry or Auto mode.
Operating Instructions Child Lock Operation Procedure 1 Press the fan speed button and High temperature setting buttons simultaneously for 3 conds. The unit will respond with beep. After 3 second, it will shift 2 3 After 3 seconds, it will shift During Child Lock Operation Whenever you press any Button on Display Panel, it will immediately display “ ”, which means Display panel is Locked. ∑ All the Button on the indoor unit Display panel will not work.
Maintenance and Service ENGLISH Maintenance and Service CAUTION: Before performing any maintenance, turn off the main power to the system. During the season Cleaning of the air filters. Recommended about once every two weeks Cleaning of the air cleaner. Recommended about once every three months Remove the Air Filter. Take hold of the tab and pull slightly forward to remove the filter. Remove the Air Cleaner. Take hold of the tab and pull slightly forward to remove the air cleaner. Clean.
Maintenance and Service Troubleshooting Check the following points before requesting repairs or service.... If the malfunction persist, please contact your dealer. Case Does not operate. Explanation See page • Have you made a mistake in timer operation? • Has the fuse blown or has the circuit breaker been tripped? • Is the power Switch at Off? • Is the unit at the starting of Heating Operation? If yes, Hot-start is activating. • Is the unit in the Deicing? If yes, wait for finishing the Deicing.
