OWNER’S MANUAL M228WD Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
SAFETY PRECAUTIONS Please read these safety precautions carefully before using the product. Warning If you ignore the warning message, you may be seriously injured or there is a possibility of ccident or death. Caution If you ignore the caution message, you may be slightly injured or the product may be damaged Precautions in installing the Product Warning Keep away from heat sources like electrical heaters. - Electrical shock, fire, malfunction or deformation may occur.
SAFETY PRECAUTIONS Electrical Power Related Precautions Warning Make sure to connect the power cable to the grounded current. - You may be electrocuted or injured. Use the rated voltage only. - The product can be damaged, or you may be electrocuted. In the presence of thunder and lightning, never touch the power cord and signal cable because it can be very dangerous. - It can cause electric shock. Do not connect several extension cords, electrical appliances or electrical heaters to a single outlet.
SAFETY PRECAUTIONS Caution Do not shock the product when moving it. - You may be electrocuted or the product can be damaged. Do not dispose the product-packing box. Use it when you move. Make the panel face forward and hold it with both hands to move. - If you drop the product, the damaged product can cause electric shock or fire. Contact with the service center for repair. Precautions in Using the Product Warning Do not disassemble, repair or modify the product at your own discretion.
PREPARATION FRONT PANEL CONTROLS ■ This is a simplified representation of the front panel. Here shown may be somewhat different from your set.
PREPARATION BACK PANEL INFORMATION A This is a simplified representation of the back panel. Here shown may be somewhat different from your set. 1 PCMCIA CARD SLOT 3 4 HDMI/DVI IN RS-232C IN (CONTROL & SERVICE) 2 EJECT AC IN AV V1 AV V2 COMPONENT IN VIDEO AUDIO Y PB PR L RGB (PC) IN AUDIO IN (RGB/DVI) ANTENNA IN 5 1 2 3 4 6 6 PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.
PREPARATION STAND INSTALLATION ■ Here shown may be somewhat different from your set. 1 Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. 2 Hold the h i n g e b o d y and bend it upward. 3 Insert the s t a n d b o d y into the product until clicking sound. Hinge Body Stand Body 4 Assemble the parts of the s t a n d b o d y with c o v e r b a s e of the product.
PREPARATION DETACHING STAND ■ 8 Here shown may be somewhat different from your set. 1 Place the set with its front facing downward on a cushion or soft cloth. 2 Pull cover base backward during pressing botton on stand body. 3 Hold cover base and pull with shake it backward to separate from stand body. 4 Hold the stand and bend it upward. 5 Pull stand body to separate from set during pressing 2 latches.
PREPARATION BACK COVER FOR WIRE ARRANGEMENT ■ Here shown may be somewhat different from your set. 1 Connect the cables as necessary. To connect an additional equipment, see the E x t e r n a l E q u i p m e n t S e t u p section. 2 Install the C A B L E M A N A G E M E N T as shown. How to remove the cable management First, press the cable management. Hold the C A B L E M A N A G E M E N T with both hands and pull it upward.
PREPARATION WALL MOUNT: HORIZONTAL INSTALLATION For proper ventilation, allow a clearance of 4" on each side and from the wall. Detailed installation instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. 4 inches 4 inches 4 inches 4 inches 4 inches DESKTOP PEDESTAL INSTALLATION For proper ventilation, allow a clearance of 4inches on each side from the wall.
PREPARATION POSITIONING YOUR DISPLAY ■ Here shown may be somewhat different from your set. Adjust the position of the panel in various ways for maximum comfort. • Tilt range 0° ~ 3° 12°~8° LOCATION Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air.
PREPARATION KENSINGTON SECURITY SYSTEM - The product is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. - For the detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System. For further information, contact h t t p : / / w w w . k e n s i n g t o n . c o m, the internet homepage of the Kensington company.
PREPARATION ■ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. ANTENNA CONNECTION For optimum picture quality, adjust antenna direction. ■ An antenna cable and converter are not supplied.
EXTERNAL EQUIPMENT SETUP ■ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. ■ Here shown may be somewhat different from your set. HD RECEIVER SETUP When connecting with a component cable 1 Connect the SET TOP outputs to the C O M P O N E N T I N V I D E O sockets (Y PB PR) on the set. 2 Connect the audio cable from the SET TOP to C O M P ON E N T I N A U D I O sockets of the set.
EXTERNAL EQUIPMENT SETUP When connecting with a HDMI HDMI/DVI IN 1 Connect the HDMI output of the digital set-top box to the H D M I / D V I I N jack on the set. 2 Select HDMI/DVI (DTV) input source with using the I N P U T button on the remote control. 1 Input MENU EXIT DTV TV AV1 OK AV2 INFO i GUIDE Component RGB HDMI G DTV ! NOTE G G G When the output device is HDMI / DVI Settop box or DVD.
EXTERNAL EQUIPMENT SETUP DVD SETUP When connecting with a component cable 1 2 Connect the video output sockets (Y PB PR) of the DVD to the C O M P O N E N T I N V I D E O sockets (Y PB PR) of the set. COMPONENT IN VIDEO AUDIO Y PB PR L R Connect the audio cable from the DVD to C O M P O N E N T I N A U D I O sockets of the set. 3 Press the I N P U T button to select Component. 4 Press the P L A Y button on the DVD. The DVD playback picture appears on the screen.
EXTERNAL EQUIPMENT SETUP When connecting with a Euro Scart AV 1 1 Connect the Euro scart socket of the DVD to the Euro scart socket of the set. 2 Press the I N P U T button to select AV1. AV 2 1 3 Press the P L A Y button on the DVD. The DVD playback picture appears on the screen. ! NOTE G Please use the shield scart cable. AUDIO/ VIDEO (R) AUDIO (L) When connecting HDMI cable HDMI/DVI IN 1 2 Connect the HDMI output of the DVD to the H D M I / D V I I N jack on the set.
EXTERNAL EQUIPMENT SETUP VCR SETUP To avoid picture noise (interference), leave an adequate distance between the VCR and set. ■ Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. ■ When connecting with an antenna ANTENNA IN ANT OUT S-VIDEO ANT IN OUTPUT SWITCH VIDEO L 1 Wall Jack 2 Antenna 1 Connect the RF out socket of the VCR to the aerial socket of the set.
EXTERNAL EQUIPMENT SETUP When connecting with a Euro Scart AV V1 1 2 AV V2 Connect the Euro scart socket of the VCR to the Euro scart socket of the set. Press the P L A Y button on the VCR. If your VCR outputs an AV switching signal via the Scart lead the set will auto switch to AV 1 mode on start of playback, but if you want to keep on watching in TV mode, press the D / E or NUMBER buttons. 1 Otherwise press the I N P U T button on the remote control handset to select AV 1.
EXTERNAL EQUIPMENT SETUP PC SETUP This product provides Plug and Play capability, meaning that the PC adjusts automatically to the set's settings. When connecting with a D-sub 15 pin cable 1 Connect the signal cable from the monitor output socket of the PERSONAL COMPUTER to the PC input socket of the set. 2 Connect the audio cable from the PC to the A U D I O I N ( R G B / D V I ) sock-ets of the set. 3 Press the INPUT button to select RGB. 4 Switch on the PC, and the PC screen appears on the set.
EXTERNAL EQUIPMENT SETUP When connecting with a HDMI to DVI cable 1 Connect the DVI output of the PC to the H D M I / D V I I N jack on the set. HDMI/DVI IN 2 Connect the audio cable from the PC to the A U D I O I N ( R G B / D V I ) sockets of the set. 3 Select HDMI/DVI (PC) input source with using the I N P U T button on the remote control.
EXTERNAL EQUIPMENT SETUP When connecting with a HDMI to HDMI cable 1 Connect the HDMI output of the PC to the H D M I / D V I I N jack on the set. 2 Select HDMI (PC) input source with using the I N P U T button on the remote control. HDMI/DVI IN 1 Input DTV MENU EXIT TV AV1 OK INFO i AV2 GUIDE Component RGB HDMI G PC ! NOTE If the set is cold, there may be a small “flicker” when the set is switched on. This is normal, there is nothing wrong with the set.
EXTERNAL EQUIPMENT SETUP RGB, HDMI/DVI-PC Preset mode Resolution Horizontal Frequency(kHz) Vertical Frequency(Hz) 720x400 31.468 31.469 37.500 37.879 46.875 48.363 60.123 67.500 63.981 79.976 64.674 65.290 70 60 75 60 75 60 75 75 60 75 60 60 640x480 800x600 1024x768 1152x864 1280x1024 1680x1050 HDMI/DVI-DTV supported mode Resolution 720x480 640x480 720x480 720x576 1280x720 1920x1080 Horizontal Frequency(kHz) Vertical Frequency(Hz) 31.47 31.50 31.50 31.50 31.47 31.47 31.25 45.00 44.96 44.96 28.
EXTERNAL EQUIPMENT SETUP Screen Setup for PC mode Auto Configure (RGB mode only) Automatically adjusts picture position and minimizes image shaking.After adjustment, if the image is still not correct, your set is functioning properly but needs further adjustment. Auto configure This function is for the automatic adjustment of the screen position, clock, and phase. The displayed image will unstable for a few seconds while the auto configuration is in progress.
EXTERNAL EQUIPMENT SETUP Adjustment for screen Phase, Clock, Position If the picture isn’t clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. To correct the screen size, adjust C l o c k. This function works in the following mode : RGB. C l o c k This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. SETUPO Auto Config. PICTUREO Manual Config.
EXTERNAL EQUIPMENT SETUP Selecting Wide SXGA mode To see a normal picture, match the resolution of RGB mode and selection of SXGA mode. This function works in the following mode: RGB mode 1 Press the MENU button and then use D or E button to select the SCREEN menu. 2 Press the G button and then use D or E button to select SXGA Mode. 3 Press the G button and then use D or E button to select the desired SXGA resolution. 4 SETUPO Auto Config. PICTUREO Manual Config.
EXTERNAL EQUIPMENT SETUP Initializing (Reset to original factory settings) This function operates in current mode. To initialize the adjusted value. 1 Press the MENU button and then select the OPTION menu. 2 Press the G button and then Factory Mode. D or E button to select 3 Press the G button and then Factory Reset. D or E button to select 4 D or E button to Move MENU Prev. 1 Press the G button. The message “If you enter a password, all user setting will be reset” will appear.
WATCHING TV /PROGRAMME CONTROL REMOTE CONTROL KEY FUNCTIONS When using the remote control, aim it at the remote control sensor on the set. POWER Switches the set on from off or off to on. TV D/A POWER TV/RADIO TEXT I/II INPUT D/A INPUT Selects digital or analogue mode. Switches the set on from off. MUTE INPUT External input mode rotate in regular sequence. Switches the set on from off. 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW MENU TV/RADIO Selects Radio or TV channel in digital mode.
WATCHING TV /PROGRAMME CONTROL TV D/A POWER TV/RADIO TEXT I/II INPUT 1 TELETEXT These buttons are used for teletext. BUTTONS For further details, see the ‘Teletext’ section. MUTE 1 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW MENU Coloured These buttons are used for teletext (only T E L E T E X T buttons models) or P r o g r a m m e e d i t. RATIO Selects your desired picture format. SLEEP Sets the sleep timer. SUBTITLE Recalls your preferred subtitle in digital mode.
WATCHING TV /PROGRAMME CONTROL TURNING ON THE TV - If your TV will be turned on, you will be able to use its features. TV D/A 1 First, connect power cord correctly. 2 Turn on power by pressing the power button on the product. 3 Press the TV button on the remote control. 4 Set the channel by using the PR+ / - buttons or number buttons on the remote control. . POWER TV/RADIO TEXT I/II MUTE 1 2 3 4 5 6 7 8 9 LIST 0 Q.
WATCHING TV /PROGRAMME CONTROL PROGRAMME SELECTION 1 Press the P R + or - or NUMBER buttons to select a programme number. TV D/A POWER TV/RADIO TEXT I/II INPUT MUTE 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW MENU EXIT VOLUME ADJUSTMENT OK GUIDE INFO i 1 Press the VOL + or - button to adjust the volume. BACK If you want to switch the sound off, press the MUTE button. * VOL PR FAV You can cancel this function by pressing the MUTE, VOL + or - , or I/II button.
WATCHING TV /PROGRAMME CONTROL ON SCREEN MENUS SELECTION AND ADJUSTMENT Your set's OSD (On Screen Display) may differ slightly from what is shown in this manual. 1 Press the M E N U button and then D or E button to display each menu. 2 Press the G button and then D or E button to select a menu item. 3 Change the setting of an item in the sub or pull-down menu with F or G button. You can move to the higher level menu by pressing the O K or M E N U button.
WATCHING TV /PROGRAMME CONTROL AUTO PROGRAMME TUNING (IN DIGITAL MODE) Use it to automatically find and store all of the programmes. When you start auto programming in digital mode, all the stored service information will be deleted. 1 Press the MENU button and then D or E button to select the SETUP menu. 2 Press the G button and then D or E button to select Auto Tuning.
WATCHING TV /PROGRAMME CONTROL MANUAL PROGRAMME TUNING (IN DIGITAL MODE) Manual Tuning lets you manually add a programme to your programme list. 1 Press the MENU button and then D or E button to select the SETUP menu. 2 Press the G button and then D or E button to select Manual Tuning.
WATCHING TV /PROGRAMME CONTROL PROGRAMME EDIT (IN DIGITAL MODE) When a programme number is skipped, it means that you will be unable to select it using PR + or - button during TV viewing. If you want to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the Programme edit menu. This function enables you to skip the stored programmes. It’s available in some countries only to move a programme number by YELLOW button.
WATCHING TV /PROGRAMME CONTROL Mini Glossary Displayed when the DTV Programme. TEXT Displayed when the Teletext Programme. Displayed when the Favourite Programme. Displayed when the Subtitle Programme. Displayed when the Locked Programme. Displayed when the Scramble Programme. Displayed when the Radio Programme. Displayed when the Dolby Programme. Displayed when the MHEG Programme. A Skipping a programme number 1 Select a programme number to be skipped with the D or E or F or G button.
WATCHING TV /PROGRAMME CONTROL 5V ANTENNA POWER (IN DIGITAL MODE ONLY) Even if there isn’t a special 5V adapter power in the external antenna, this function can output 5V in the set. 1 Press the MENU button and then D or E button to select the SETUP menu. 2 Press the G button and then use D or E button to select 5V Antenna Power. SETUPO Auto Tuning PICTUREO Manual Tuning AUDIOO Programme Edit 5V Antenna Power TIMEO Software Update OPTIONO Diagnostics SCREENO CI Information Move 3 MENU Prev.
WATCHING TV /PROGRAMME CONTROL SOFTWARE UPDATE (IN DIGITAL MODE ONLY) Software Update means software can be downloaded through the digital terrestrial broadcasting system. 1 Press the MENU button and then select the SETUP menu. 2 Press the G button and then D or E button to select Software update.
WATCHING TV /PROGRAMME CONTROL DIAGNOSTICS (IN DIGITAL MODE ONLY) This function enables you to watch Manufacturer, Model/Type, Serial Number and Software Version. It’s displayed the information and signal strength of the tuned MUX. It’s displayed the signal information and service name of the selected MUX. 1 Press the M E N U button and then D or E button to select the SETUP menu. 2 Press the G button and then use D or E button to select Diagnostics.
WATCHING TV /PROGRAMME CONTROL CI [COMMON INTERFACE] INFORMATION (IN DIGITAL MODE ONLY) This function enables you to watch some scrambled services (pay services). If you remove the CI Module, you can’t watch the pay services. When the module is inserted to CI slot, you can access the module menu. To purchase a module and smart card, contact your supplying dealer. Do not often insert or remove a CAM module from the set. It may cause a trouble.
WATCHING TV /PROGRAMME CONTROL AUTO PROGRAMME TUNING (IN ANALOGUE MODE) All stations that can be received are stored by this method. It is recommended that you use Auto tuning during installation of this set. 1 Press the M E N U button and then D or E button to select the SETUP menu. 2 Press the G button and then D or E button to select Auto Tuning. 3 Press the G button to select System.
WATCHING TV /PROGRAMME CONTROL MANUAL PROGRAMME TUNING (IN ANALOGUE MODE) Manual Tuning lets you manually tune and arrange the stations in whatever order you desire. 1 Press the MENU button and then D or E button to select the SETUP menu. 2 Press the G button and then D or E button to select Manual Tuning. 3 Press the G button to select Storage.
WATCHING TV /PROGRAMME CONTROL FINE TUNING (IN ANALOGUE MODE) Normally fine tuning is only necessary if reception is poor. 1 Press the MENU button and then D or E button to select the SETUP menu. 2 Press the G button and then D or E button to select Manual Tuning. 3 Press the G button and then D or E button to select Fine. SETUPO Auto Tuning PICTUREO Manual Tuning AUDIOO Programme Edit 4 Press the G button and then F or G button to fine tune for the best picture and sound.
WATCHING TV /PROGRAMME CONTROL PROGRAMME EDIT (IN ANALOGUE MODE) This function enables you to delete or skip the stored programmes. Also you can move some stations to other programme numbers or copy a blank station data into the selected programme number. 1 SETUPO Auto Tuning PICTUREO Manual Tuning AUDIOO Programme Edit Press the MENU button and then D or E button to select the SETUP menu. TIMEO OPTIONO 2 Press the G button and then D or E button to select Programme Edit.
WATCHING TV /PROGRAMME CONTROL A Moving a programme a Select a programme to be moved with D or E or F or G button. b Press the YELLOW button. c Move the programme to the desired programme number with the D or E or F or G button. d Press the YELLOW button again to release this function. A Skipping a programme number a Select a programme number to be skipped with D or E or F or G button. b Press the BLUE button. The skipped programme number turns to blue.
WATCHING TV /PROGRAMME CONTROL CALLING THE PROGRAMME TABLE You can check the programmes stored in the memory by displaying the programme table. A Displaying programme LIST 1 Press the LIST button to display the PROGRAMME LIST menu. DTV List D 801 YLE TV1 The programme list appears on the screen. 802 YLE TV2 803 YLE FST • You may find some blue programmes. They have been set up to be skipped by auto programming or in the programme edit mode.
WATCHING TV /PROGRAMME CONTROL INPUT SOURCE SELECTION Sets a label to each input source which is not in use. 1 Press the M E N U button and then use D or E button to select the OPTION menu. 2 Press the G button and then use D or E button to select Input Label. SETUPO Language PICTUREO Country AUDIOO Lock System Parental Control TIMEO Input Label OPTIONO Factory Mode SCREENO Move 3 4 5 MENU Prev. Press the G button and then use D or E button to select the source: AV1, AV2, Comp., RGB or HDMI.
EPG (ELECTRONIC PROGRAMME GUIDE) (IN DIGITAL MODE) This system has an Electronic Programme Guide (EPG) to help your navigation through all the possible viewing options. The EPG supplies information such as programme listings, start and end times for all available services. In addition, detailed information about the programme is often available in the EPG (the availability and amount of these programme details will vary, depending on the particular broadcaster).
EPG (ELECTRONIC PROGRAMME GUIDE) (IN DIGITAL MODE) Button Function in NOW/NEXT Guide Mode Remote Control Buttons RED YELLOW BLUE F or G or E PR + or GUIDE/EXIT TV/RADIO INFO i D Function Change EPG mode Enter Timer Record/Remind setting mode Enter Timer Record/Remind list mode Change to the selected channel Select NOW or NEXT Programme Select the Broadcasting Programme Page Up/Down Switch off EPG Select TV or RADIO Programme The detail information on or off Button Function in 8 Days Guide Mode Remote Con
EPG (ELECTRONIC PROGRAMME GUIDE) (IN DIGITAL MODE) Button Function in Extended Description Box Remote Control Buttons D or E YELLOW INFO i GUIDE/EXIT Function Text Up/Down Enter Timer Record/Remind setting mode The detail information on or off Switch off EPG Button Function in Record/Remind Setting Mode - This function is available only when recording equipment that use pin8 recording signalling has been connected to the DTV-OUT terminal, using a SCART cable.
PICTURE CONTROL PICTURE SIZE (ASPECT RATIO) CONTROL You can watch the screen in various picture formats; 1 6 : 9, O r i g i n a l, 4 : 3, 1 4 : 9 and Z o o m 1 / 2. If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible. There might be uncomfortable in full mode. Then change into other mode. You can adjust the enlarge proportion using D or E button. This function works in the following signal.
PICTURE CONTROL • Zoom1 Following selection will lead you to view the picture without any alternation, while filling the entire screen. However, the top and bottom portions of the picture will be cropped. Zoom1 • Zoom2 Choose Zoom2 when you want the picture to be altered, both horizontally extended and vertically cropped. The picture taking a halfway trade off between alteration and screen coverage.
PICTURE CONTROL PRESET PICTURE SETTINGS Picture Mode-Preset Dynamic Standard Mild User 1/2 1 Select this option to display with a sharp image. The most general and natural screen display status. Select this option to display with a mild image. Select this option to use the user-defined setting. SETUPO Picture Mode PICTUREO Colour Temperature Press the MENU button and then D or E button to select the PICTURE menu. 2 Press the G button and then D or E button to select Picture Mode.
PICTURE CONTROL Auto Colour Tone Control (Warm/Medium/Cool) To initialize values (reset to default settings), select the Cool option. It’s available DTV, TV, AV1, AV2, Component, HDMI-DTV mode. Choose one of three automatic colour adjustments. Set to warm to enhance hotter colours such as red, or set to cool to see less intense colours with more blue. It’s available to use this function in User mode.
PICTURE CONTROL Auto Colour Tone Control (9300K/6500K/sRGB) To initialize values (reset to default settings), select the 9300K option. It’s available RGB, HDMI-PC mode. Choose one of three automatic colour adjustments. Set to 6500K to enhance hotter colours such as red, or set to 9300K to see less intense colours with more blue. It’s available to use this function in User mode.
PICTURE CONTROL MANUAL PICTURE ADJUSTMENT Picture Mode-User option Contrast Brightness Colour Sharpness Tint Adjusts the difference between the light and dark levels in the picture. Increases or decreases amount of white in the your picture. Adjusts intensity of all colours. Adjusts the level of crispness in the edges between the light and dark areas of the picture. The lower the level, the softer the image. Adjusts the balance between red and green levels.
PICTURE CONTROL Colour Tone - User option To adjust red, green, blue to any colour temperature you prefer. SETUPO Picture Mode PICTUREO Colour Temperature AUDIOO Advanced Picture Reset OPTIONO Demo SCREENO TIMEO 1 Press the M E N U button and then D or E button to select the PICTURE menu. Move Prev. MENU 1 2 Press the G button and then D or E button to select Colour Temperature.
PICTURE CONTROL XD - PICTURE IMPROVEMENT TECHNOLOGY XD is LG electronic's unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm. It’s not available to use this function in RGB, HDMI-PC mode. 1 Press the MENU button and then D or E button to select the PICTURE menu. 2 Press the G button and then D or E button to select XD. 3 Press the G button and then D or E button to select Auto or Manual.
PICTURE CONTROL DEMO Use it to see the difference between XD Demo on and XD Demo off. It’s not available to use this function in RGB, HDMI[PC] mode. 1 SETUPO Picture Mode PICTUREO Colour Temperature Press the MENU button and then D or E button to select the PICTURE menu. AUDIOO TIMEO OPTIONO Advanced Picture Reset Demo SCREENO 2 Press the MENU button and then D or E button to select XD Demo. Move MENU Prev. 1 3 Press the G button to begin XD Demo.
PICTURE CONTROL ADVANCED - CINEMA Set up the product for the best picture appearance for viewing movies. This feature operates only in TV, AV and Component 480i/576i mode. SETUPO Picture Mode PICTUREO Colour Temperature 1 Press the M E N U button and then D or E button to select AUDIOO Advanced Picture Reset OPTIONO Demo SCREENO TIMEO the PICTURE menu. 2 Press the G button and then D or E button to select Advanced. Move MENU Prev. 1 3 Press the G button and then D or E button to select Cinema.
PICTURE CONTROL ADVANCED - BLACK(DARKNESS) LEVEL When you watch the movie, this function adjusts the set to the best picture appearance. Adjusting the contrast and the brightness of the screen using the black level of the screen. This function works in the following mode: AV (NTSC-M) or HDMI. 1 2 SETUPO Picture Mode PICTUREO Colour Temperature Press the M E N U button and then D or E button to select the PICTURE menu.
PICTURE CONTROL PICTURE RESET Returns to the default settings Picture Mode, Colour Temperature, XD, Advanced at the factory. 1 SETUPO Picture Mode PICTUREO Colour Temperature Press the M E N U button and then D or E button to select the PICTURE menu. AUDIOO TIMEO OPTIONO Advanced Picture Reset Demo SCREENO 2 Press the G button and then D or E button to select Picture Reset. Move MENU Prev. 1 3 Press the G button to initialize the adjusted value.
SOUND & LANGUAGE CONTROL AUTO VOLUME LEVELER AVL automatically keeps on an equal volume level even if you change programmes. 1 Press the MENU button and then select the AUDIO menu. D or E SETUPO Sound Mode PICTUREO Auto Volume AUDIOO Balance button to 0 TIMEO OPTIONO 2 Press the G button and then D or E button to select Auto Volume. 3 Press the G button and then D or E button to select Off or On. 4 SCREENO Move MENU Prev. 1 Press the EXIT button to disappear the menu window.
SOUND &LANGUAGE CONTROL PRESET SOUND SETTINGS-SOUND MODE You can select your preferred sound setting; Surround MAX, Standard, Music, Movie or Sports and you can also adjust the sound frequency of the equalizer. Sound Mode lets you enjoy the best sound without any Special adjustment because the TV sets the appropriate sound options based on the programme content.
SOUND &LANGUAGE CONTROL SOUND SETTING ADJUSTMENT -USER MODE Adjust the sound equalizer. 1 Press the M E N U button and then D or the AUDIO menu. E button to select SETUPO Sound Mode PICTUREO Auto Volume AUDIOO Balance 0 TIMEO 2 Press the G button and then D or Sound Mode. E button to select 3 Press the G button and then D or E button to select User. 4 Press the G button. OPTIONO SCREENO Move 5 6 MENU Prev.
SOUND &LANGUAGE CONTROL BALANCE You can adjust the sound balance of speaker to the levels you prefer. 1 Press the MENU button and then select the AUDIO menu. D or E SETUPO Sound Mode PICTUREO Auto Volume AUDIOO Balance button to 0 TIMEO OPTIONO 2 Press the G button and then D or E button to select Balance. 3 Press the G button and then desired adjustment. 4 F or G button to make SCREENO Move MENU Prev. 1 Press the EXIT button to disappear the menu window.
SOUND &LANGUAGE CONTROL I/II Stereo/Dual Reception (In Analogue Mode Only) When a programme is selected, the sound information for the station appears after the programme number and station name disappear. Broadcast On Screen Display Mono MONO Stereo STEREO Dual DUAL I A Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono by pressing the I / I I button twice. In mono reception, the depth of sound is improved.
SOUND &LANGUAGE CONTROL NICAM Reception (In Analogue Mode Only) If the set is equipped with the receiver for NICAM reception, the high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received. Sound output can be selected according to the type of received broadcast as follows by pressing the I/II button repeatedly. 1 When N I C A M m o n o is received, you can select N I C A M M O N O or F M M O N O.
SOUND &LANGUAGE CONTROL ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION Installation guide menu appears on TV screen when it is turned on for the first time. Press the D or E or F or G button and then, O K button to select your desired language. 1 2 Press the D or E button and then, O K button to select your country. TV D/A POWER TV/RADIO TEXT I/II INPUT MUTE 1 2 3 4 5 6 7 8 9 LIST 0 Q.
SOUND &LANGUAGE CONTROL LANGUAGE SELECTION (IN DIGITAL MODE ONLY) TV/RADIO TEXT A u d i o function lets you select your preferred language for audio. If the audio data in selected language is not broadcasted, default language audio will be played. Use S u b t i t l e function when two or more subtitle languages are broadcasted. If the subtitle data in selected language is not broadcasted, default language subtitle will be displayed. I/II 1 2 3 4 5 6 7 8 9 LIST 0 Q.
TIME SETTING CLOCK SETUP The clock is set automatically when receiving the digital signal. (You can set the clock if the set has no DTV signal.) You must set to the time correctly before using on/off time function. 1 Press the MENU button and then select the TIME menu. 2 Press the Clock. 3 Press the G button and then F or G button to select either the year, date, or time option.
TIME SETTING AUTO ON/OFF TIMER SETTING The Off time automatically switches the set to standby at the preset time. Two hours after the set is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed. Once the on time/off time is set, these functions operate daily at the preset time. Off time function overrides On timer function if they are set both to the same time. The set must be in standby mode for the On timer to work.
TIME SETTING AUTO SHUT-OFF SETTING If set to on and there is no input signal, the set turns off automatically after 10 minutes. 1 Press the MENU button and then select the TIME menu. 2 Press the G button and then Auto Sleep. D or E button to select 3 Press the G button and then Off or On. D or E button to select 4 D or E SETUPO Clock PICTUREO Off time AUDIOO On time Auto Sleep TIMEO Time Zone OPTIONO button to SCREENO Move MENU Prev.
TIME SETTING TIME ZONE SETUP When you select a Time Zone city, TV time is set by the time offset information based on Time Zone and GMT (Greenwich Mean Time) information which is received to broadcasting signal when time is set automatically by a digital signal. 1 Press the MENU button and then select the TIME menu. 2 Press the G button and then D or E button to select Time Zone. 3 Press the G button and then F or G button to select your viewing area time zone.
PARENTAL CONTROL / RATINGS SET PASSWORD & LOCK SYSTEM If you first enter the password, press ‘0’, ‘0’, ‘0’, ‘0’ on the remote control handset. 1 Press the MENU button and then select the OPTION menu. 2 Press the G button and then Lock System. D or E button to select 3 Press the On. F or G button to select G button and then D or E SETUPO Language PICTUREO Country AUDIOO Lock System Parental Control TIMEO Input Label OPTIONO Factory Mode SCREENO button to Move MENU Prev.
PARENTAL CONTROL / RATINGS PARENTAL CONTROL This function operates according to information from the broadcasting station. Therefore if the signal has wrong information, this function dose not operates. Lets you set up blocking schemes to block specific channels, ratings, and external viewing sources. A password is required to gain access to this menu. This set is programmed to remember which option it was last set to even if you turn the set off.
TELETEXT This feature is not available in all countries. Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programmes, share prices and many other topics. The teletext decoder of this set can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number.
TELETEXT FASTEXT The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button. A Page selection 1 2 3 4 Press the i button to select the index page. You can select the pages which are colour coded along the bottom line with the same coloured buttons. Corresponding to the SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER buttons in FASTEXT mode.
DIGITAL TELETEXT *This function works in UK only. The set gives you access to a digital teletext which is greatly improved in various aspects such as text, graphics and so on. This digital teletext can be accessed by special digital teletext services and specific services which broadcast digital teletext. You should select off from the subtitle language to display teletext by pressing SUBTITLE button.
APPENDIX TROUBLESHOOTING The operation does not work normally. Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the set. A Ensure that the batteries are installed with correct polarity (+ to +, - to -). A Ensure that the correct remote operating mode is set: TV, VCR etc. A Install new batteries.
APPENDIX The audio function does not work. A Picture OK & No sound A A A No output from one of the speakers Unusual sound from inside the product Press the VOL + or - button. Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly? A Adjust Balance in menu option. A A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product.
APPENDIX Only RGB mode applied ‘Unknown Product’ message appears when the product is connected. A Install the product driver, which is provided with the product, or download it from the web sige. (http://www.lge.com) A See if the plug&play function is supported by referring to the video card user’s guide. Did you install the driver? The screen image looks abnormal. A Is the screen position wrong? Do thin lines appear on the background screen? Horizontal noise appear or the characters look blurred.
APPENDIX MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new set. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1 Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
APPENDIX PRODUCT SPECIFICATIONS LCD Panel Video Signal Screen Type 22 inches Wide (55.868 cm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size : 55.868 cm Pixel Pich 0.282 mm Max.
APPENDIX PROGRAMMING THE REMOTE CONTROL The remote is a multi-brand or a universal remote. It can be programmed to operate most remotecontrollable devices of other manufacturers. Note that the remote may not control all models of other brands. Programming a code into a remote mode 1 Test your remote control.
APPENDIX VCR Brand AIWA AKAI Codes 034 016 125 AMPRO 072 ANAM 031 AUDIO DYNAMICS 012 BROKSONIC 035 CANON 028 CAPEHART 108 CRAIG 003 CURTIS MATHES 031 DAEWOO 005 065 112 DAYTRON 108 DBX 012 DYNATECH 034 ELECTROHOME 059 EMERSON 006 029 036 129 FISHER 003 FUNAI 034 GE 031 107 GO VIDEO 132 HARMAN KARDON HITACHI 004 043 INSTANTREPLAY 031 JCL 031 JCPENNY 012 040 JENSEN 043 JVC 012 048 130 KENWOOD 014 047 LG (GOLDSTAR) 001 101 LLOYD 034 LXI 003 017 MAGIN 040 86 Brand Codes Brand MAGNAVOX 031 067 012 069 1
APPENDIX IR CODES 1. How to Connect A Connect your wired remote control to the Remote Control port on the set. 2. Remote Control IR Codes A Output waveform Single pulse, modulated with 37.
APPENDIX Code (Hexa) 00 01 02 03 40 41 06 07 08 09 10 11 12 13 14 15 16 17 18 19 0B AA AB 56 5B 1E 1A 50 F0 0A 0E 43 44 53 20 2A 26 28 62 70 65 61 63 71 72 79 88 Function PR + PR VOL + VOL Up (D) Down (E) Right (G) Left (F) POWER MUTE Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 INPUT INFO i GUIDE SUBTITLE EXIT FAV Q.
APPENDIX EXTERNAL CONTROL DEVICE SETUP RS-232C Setup Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Note: RS-232C connection cables are not supplied with the product. RS-232C IN (CONTROL & SERVICE) Type of Connector; D-Sub 9-Pin Male No.
APPENDIX Set ID Use this function to specify a set ID number. Refer to ‘Real Data Mapping’. G p .92 1 Press the M E N U button and then use D or E button to select the OPTION menu. 2 Press the G button and then use D or E button to select Factory Mode. SETUPO Language PICTUREO Country AUDIOO Lock System Parental Control TIMEO Input Label OPTIONO Factory Mode SCREENO Move MENU Prev. 1 3 Press the G button and then use D or E button to select Set ID.
APPENDIX Communication Parameters Baud rate : 9600 bps (UART) A Data length : 8 bits A Parity : None Stop bit : 1 bit A Communication code : ASCII code A Use a crossed (reverse) cable. A A Command Reference List Transmission / Receiving Protocol COMMAND COMMAND DATA 1 2 (Hexadecimal) 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Colour 10. Tint 11. Sharpness 12. OSD Select 13. Remote control lock mode 14. Balance 15.
APPENDIX 01. Power (Command 2 : a) 04. Screen Mute (Command 2 : d) G To control Power On/Off of the set. G To select screen mute on/off. Transmission Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off Ack [k][d][ ][Set ID][ ][Data][Cr] 1 : Power On Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) [a][ ][Set ID][ ][OK][Data][x] Ack G To show Power On/Off. [d][ ][Set ID][ ][OK][Data][x] Transmission 05.
APPENDIX 09. Colour (Command 2 : i) 14. Balance (Command 2 : t) G To adjust the screen colour. G To adjust balance. You can also adjust colour in the PICTURE menu. Transmission You can also adjust balance in the AUDIO menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] [k][t][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping 1’. See page 91. Ack Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping 1’. See page 91.
APPENDIX 19. Abnormal State (Command 2 : z) G To recognize an abnormal state. Transmission [k][z][ ][Set ID][ ][FF][ ][Cr] 22. Send IR Code (Command 1 : m, Command 2 : c) G To send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr] Data FF : Read Ack Data Key code - Refer to page 85.
APPENDIX 23. Input select (Command 1 : x, Command 2 : b) (Main Picture Input) G To select input source for main picture.
