Room Air Conditioner OWNER’S MANUAL Please read this manual carefully and thoroughly before operating this unit.
Room Air Conditioner Owner’s Manual TABLE OF CONTENTS Safety Precautions.........................3 FOR YOUR RECORDS Write the model and serial numbers here: Model # Serial # Prior to Operation ..........................9 You can find them on a label on the side of each unit. Dealer's Name Date Purchased Introduction ..................................10 Electrical Safety ...........................11 Operating Instructions.................12 Maintenance and Service ............
Safety Precautions Safety Precautions To prevent the injury of the user or other people and property damage, the following instructions must be followed. n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage to properties only. n The meanings of the symbols used in this manual are as shown below.
Safety Precautions Be cautious when unpacking and installing the product. • Sharp edges could cause injury. Be especially careful of the case edges and the fins on the condenser and evaporator. Be sure the installation area does not deteriorate with age. • If the base collapses, the air conditioner could fall with it, causing property damage, product failure, and personal injury. For installation, always contact the dealer or an Authorized Service Center.
Safety Precautions Use a dedicated outlet for this appliance. Grasp the plug to remove the cord from the outlet. Do not touch it with wet hands. Do not place a heater or other appliances near the power cable. • There is risk of fire or electrical shock. • There is risk of fire or electrical shock. • There is risk of fire and electric shock. Do not allow water to run into electric parts. Do not store or use flammable gas or combustibles near the air conditioner.
Safety Precautions Do not open the inlet grill of the product during operation. (Do not touch the electrostatic filter, if the unit is so equipped.) • There is risk of physical injury, electric shock, or product failure. When the product is soaked (flooded or submerged), contact an Authorized Service Center. • There is risk of fire or eletric shock. Unplug the appliance before performing cleaning or maintenance.
Safety Precautions Do not install the product where the noise or hot air from the outdoor unit could damage the neighborhoods. • It may cause a problem for your neighbors. Use two or more people to lift and transport the air conditioner. • Avoid personal injury. Do not install the product where it will be exposed to sea wind (salt spray) directly. • It may cause corrosion on the product.
Safety Precautions Always insert the filter securely. Clean the filter every two weeks or more often if necessary. • A dirty filter reduces the efficiency of the air conditioner and could cause product malfunction or damage. Do not insert hands or other objects through the air inlet or outlet while the air conditioner is plugged in. • There are sharp and moving parts that could cause personal injury. Use a firm stool or ladder when cleaning or maintaining the air conditioner.
Prior to Operation Prior to Operation Preparing for Operation 1. Contact an installation specialist for installation. 2. Plug in the power plug properly. 3. Use a dedicated circuit. 4. Do not use an extension cord. 5. Do not start/stop operation by plugging/unplugging the power cord. 6. If the cord/plug is damaged, replace it with only an authorized replacement part. Usage 1. Being exposed to direct airflow for a long time may be hazardous to your health.
Introduction Introduction Symbols used in this Manual This symbol alerts you to the risk of electric shock. This symbol alerts you to hazards that may cause harm to the air conditioner. NOTICE This symbol indicates special notes. Features This appliance should be installed in accordance with national wiring regulations. This guide acts as a guide to help to explain product features.
Electrical Safety Electrical Safety • This appliance must be properly grounded. To minimize the risk of electric shock, you must always plug into a grounded outlet. • Do not cut or remove the grounding. • Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal and not insulated, and the wall receptacle is grounded through the house wiring.
Operating Instructions Operating Instructions How to insert the Batteries 1. Remove the battery cover by pulling it according to the arrow direction. 2. Insert new batteries making sure that the (+) and (-) of battery are installed correctly. 3. Reattach the cover by sliding it back into position. NOTICE Use 2 AAA(1.5volt) batteries. Do not use rechargeable batteries. Storage and Tips for using the Remote Controller • The remote controller may be stored by mounting it on a wall.
Operating Instructions Remote Control Operations The remote control transmits the signals to the system. Features of the Remote Control- Door Closed Signal transmitter 5 6 1 5 6 Signal transmitter OL A/SWING JET CO POWER 1 TEMP 3 3 FAN SPEED 4 2 4 2 ON MODE ON Flip-up door (closed) TYPE A START/STOP BUTTON 1 Operation starts when this button is Flip-up door (closed) TYPE B INDOOR FAN SPEED 4 SELECTOR Used to select fan speed in four steps low, medium, high, or CHAOS.
Operating Instructions Features of the Remote Control- Door Opened Signal transmitter ON/OFF TIMER BUTTONS 1 Used to set the time of starting and stopping operation. TIME SETTING BUTTONS 2 Used to adjust the time, (See page 22) TIMER SET/CANCEL BUTTONS 3 Used to set the timer when the desired time is obtained and to cancel the Timer operation. (See page 22) SLEEP MODE AUTO BUTTON 4 Used to set Sleep Mode Auto operation.
Operating Instructions Cooling operation 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Cooling Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. ON Cooling 3 OL A/SWING JET CO Auto Healthy Dehumidification Heating (Heat pump model only) Close the door of the remote controller.
Operating Instructions Auto operation (Optional) ON 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Auto Operation, press the operation mode selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow.
Operating Instructions Healthy dehumidification operation 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Healthy Dehumidification Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow.
Operating Instructions Heating operation (Heat pump model only) 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Heating Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. ON Cooling 3 Auto Healthy Heating Dehumidification (Heat pump model only) Close the door of the remote controller.
Operating Instructions Jet cool operation OL A/SWING JET CO 1 Press the Start/Stop button. The unit will respond with a beep. 2 Press the Jet Cool button to operate the speed cooling mode and the unit will operate at super high fan speed on cooling mode for 30 minutes. 3 To cancel the Jet Cool mode, press the Jet Cool button, the fan speed button or the room temperature setting button again and the unit will operate at high fan speed on cooling mode.
Operating Instructions NEO PLASMA purification operation(Optional) OL A/SWING JET CO POWER TEMP 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. Press the PLASMA button. Operation will start when the button is pressed and stop when the button is pressed again. 3 Set the fan speed again with the door of the remote controller closed. You can select the fan speed in four steps-low, medium, high or CHAOS.
Operating Instructions 2nd F operation CANCEL ON OFF SET AUTO CLEAN A/SWING L O JET CO 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller and press the 2nd Function button to operate functions printed blue color under buttons. (Check the indication of 2nd function on the display of the remote controller.) 3 2nd function disappears in a short time automatically or when the button is pressed again.
Operating Instructions Additional Features SLEEP Sleep mode 1. Press the Sleep Mode Auto button to set the time you want the unit to stop automatically. 2. The Timer is programmed in one-hour increments by pressing the Sleep Mode Auto button 1 to 7 times. The sleep mode is available for 1 to 7 times. To alter the time period in steps of 1 hour, press the Sleep Mode Button while aiming at air conditioner. 3. Make sure the Sleep Mode Auto LED lights up.
Operating Instructions Vertical Airflow Direction Control The up/down airflow (Vertical Airflow) can be adjusted by using the remote control. 1. Press the Start/Stop button to start the unit. 2. Press Chaos Swing button and the louvers will swing up and down. Press the Chaos Swing button again to set the vertical louver at the desired airflow direction.
Operating Instructions Auto clean (Optional) AUTO CLEAN 1. Whenever you press the AUTO CLEAN button, Auto Clean Function will be reserved and cancelled. 2. Auto Clean function works before and after cooling or dehumidification mode. For details, refer to the below points. 3. When the unit is started after the reservation of Auto Clean ,the Cool Start function operates and indoor Fan is started after 20 seconds. 4.
Operating Instructions Forced operation Please follow the step 1 to step 5 for forced operation. 1. 2. 3. 4. 5. Turn ON the unit using power button. Turn OFF the unit using power button. Switch OFF the mains supply to the unit. Switch ON the mains supply to the unit. Turn ON the unit using the power button. Open the front panel upward After turning ON the unit will operate according to the table below : Power button Note : Forced operation button location varies with model.
Maintenance and Service Maintenance and Service CAUTION : Before performing any maintenance, turn off the main power to the system. Indoor Unit Grille, Case, and Remote Control Never use any of the followings: • Water hotter than 40°C Could cause deformation and/or discoloration. • Volatile substances Could damage the surfaces of the air conditioner. Turn the system off before cleaning. To clean, wipe with a soft, dry cloth. Do not use bleach or abrasives.
Maintenance and Service Replacement of Purifying Filter(Option) • Recomended use period : About 2 years 1 Open front panel and remove air 2 Remove air purifying filters. filters. 3 Insert new air purifying filters. 4 Reinsert air filters and close front panel. Air purifying filter Outdoor Unit The heat exchanger coils and panel vents of the outdoor unit should be checked regularly.
Maintenance and Service Common Problems and Solutions Before calling for service If you have problems with your air conditioner, read the following information and try to solve the problem. If you cannot find a solution, turn off the air conditioner and contact your dealer. Air conditioner does not operate 1. Ensure that the air conditioner is plugged into a proper outlet. 2. Check the fuse or circuit breaker. 3. Check whether the voltage is unusually high or low.
Maintenance and Service When the air conditioner is not going to be used for a long time. When air conditioner is not going to be used for a long time. When the air conditioner is to be used again. Operate the air conditioner on Air circulation mode (Refer to page 23) for 2 to 3 hours. Clean the air filter and install it in the indoor unit. (Refer to page 26 for cleaning filters.) • This will dry out the internal mechanisms. Turn off the circuit breaker, and disconnect the plug.
Before you call for service... ? Troubleshooting Tips! Save time and money! Check the following points before requesting repairs or service.... If the fault persists, please contact your dealer or service center. Case Explanation See page The air conditioner does not operate. • Have you made a mistake in timer operation? • Has the fuse blown or has the circuit breaker been tripped? 22 The room has a peculiar odor.
