| ® Page 11 Friday, February 7, 2020 11:44 AM wy] INSTALLATION 11 —¢e INSTALLATION Before Installing Installation Overview Please read the following installation instructions first after purchasing this product or transporting it to another location. HST19NE @ Unpacking the Refrigerator @ Choosing the Proper Location @ Disassembling/Assembling @ Connecting the Water Line @ Leveling and Door Alignment 4) WARNING + Connect to potable water supply only.
| ® sustain. book. book Page 12 Friday, February 7, 2020 11:44 AM 12 INSTALLATION Unpacking the Refrigerator 4 WARNING + Use two or more people to move and install the refrigerator. Failure to do so can result in back injury or other injury. The refrigerator is heavy. Protect the floor when moving the refrigerator for cleaning or service, Always pull the refrigerator straight out when moving It.
| ® sustain book. book Page 13 Friday, February 7, 2020 11:44 AM ol INSTALLATION 13 Dimensions and Clearances move the refrigerator through doors or narrow openings. Assembling the Doors and Drawers in this manual. and airflow and space in front to open the doors and drawers. Check the dimensions of the appliance and the installation path to ensure there is sufficient room to If an opening is too narrow to fit the refrigerator through, remove the refrigerator doors.
®[o | ® Page 14 Friday, February 7, 2020 11:44 AM 14 INSTALLATION oe ® Removing/Assembling Handles ‘When moving the refrigerator through a narrow opening, removing the doors Is preferred. The appearance of the handles may vary from what is shown. £b CAUTION When assembling or disassembling the refrigerator handles, grasp the handle firmly to avoid dropping it. Do not swing the handle into nearby people or animals. Make sure that the bracket hole of the handle fits properly into the stopper bolt of the door.
| ® Page 15 Friday, February 7, 2020 11:44 AM oe ® INSTALLATION 15 Removing/Assembling Doors and Drawers If the entrance door is too narrow for the refrigerator to pass through, remove the refrigerator doors and move the refrigerator sideways through the doorway. 4) WARNING + Use two or more people to remove and install the refrigerator doors and freezer drawer. Disconnect the electrical supply to the refrigerator before installing.
| ® Page 16 Friday, February 7, 2020 11:44 AM 16 INSTALLATION 4 Lift the door from the middle hinge pin and remove the door. £) CAUTION + Place the door, inside facing up, on a non scratching surface, Removing the Right Refrigerator Door 1 Detach all the wire harnesses @. Unscrew the ground wire @. NOTE + The number of wire harnesses may vary depending on the model. * Ground wire is only available on some models. 2 Rotate the hinge lever @ clockwise. Lift the top hinge @ free of the hinge lever latch @.
Page 17 Friday, February 7, 2020 11:44 AM + ® INSTALLATION 17 3 Connect all the wire harnesses @ and the ground screw @ HST19NE | ground wire. 4 push the water supply lines into the hole on NOTE the top case and pull them through the + The number of wire harnesses may vary back plate. depending on the model. + Ground wire is only available on some models.
| ® Page 18 Friday, February 7, 2020 11:44 AM 18 INSTALLATION * ¢ © NOTE * Gently press the collect and insert the tube until only one line shows on the tube. Removing the Full Convert Drawer 1 Pull the drawer open to full extension. Remove the basket from the rails. 2 Hold both sides of the door and remove it from the rails. Assembling the Full Convert Drawer 1 Grasp the door on each side and lower It into place on the rails. 2 pull the drawer open to full extension. Lower the basket onto the rails.
| ® book Page 18 Friday, February 7, 2020 11:44 AM wy] ® INSTALLATION 19 HST19NE | Assembling the Freezer Drawer 4 Remove the Durable basket from the rails. Remove the screws from the rails at both 1 pullout both rails simultaneously, until they ends. are fully extended. Grasp the drawer on each side and hook the drawer supports into the rail tabs located on both sides. 5 Grip both sides of the drawer and pull it up to remove it from the rails.
20 INSTALLATION | ® sustain. book. book Page 20 Friday, February 7, 2020 11:44 AM oe ® 4 Insert the drawer into the frame, and push the drawer back until It clicks into place. 5 Replace the ice bin in the drawer. Insert the Durable basket In the rail assembly. SAE An Ce NJ Assembling the Hinge Cover Position the hinge cover in its place. Insert and tighten the cover screws, Connecting the Water Line Before Beginning This water line Installation Is not covered by the refrigerator warranty.
ole ha | ® sustain. book. book Page 21 Friday, February 7, 2020 11:44 AM oe ® INSTALLATION 21 + If the water pressure remains low, call a licensed, qualified plumber. * All installations must be in accordance with local plumbing code requirements. Supplies Leaded + Copper or PEX Tubing, % in. outer diameter, to connect the refrigerator to the water supply. Be sure both ends of the tubing are cut square.
| ® sustain. book. book Page 22 Friday, February 7, 2020 11:44 AM 22 INSTALLATION NOTE The hookup line cannot be white, plastic tubing. Licensed plumbers must use only copper tubing (NDA tubing #49595 or #49599) or Cross Link Polyethylene (PEX) tubing. 4 Fasten the shutoff valve. + Fasten the shutoff valve to the cold water pipe with the pipe clamp. NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts.
sustain. book. book Page 23 Friday, February 7, 2020 11:44 AM oe ® INSTALLATION 23 @ Outlet Valve @ Ferrule {sleeve} 8 Flush out the tubing. = Turn the main water supply on and flush out the tubing until the water is clear. Shut the water off at the water valve after about one quart of water has been flushed through the tubing. Connect the tubing to the refrigerator. NOTE Before making the connection to the refrigerator, be sure that the refrigerator power cord is not plugged into the wall outlet.
| ® sustain book. book Page 24 Friday, February 7, 2020 11:44 AM 24 INSTALLATION Door Alignment (Door-in-Door Model) Left Refrigerator Door The left refrigerator door has an adjustable nut, located on the bottom hinge, to raise and lower the door for proper alignment. If the space between the doors is uneven, follow the instructions below to align the left door: Use the wrench (included with the owner's manual) to turn the nut in the door hinge to adjust the height.
