LAM-N760,N760SP_ENG 7inch Wide TFT color TV System/Mobile Monitor OWNER’S MANUAL LAM-N760SP/N760 Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely. Internet address ; http://ua.lge.
Table of contents Safety note 3-6 Main features 7-8 Installation 9-14 Parts supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Before installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Installation order for the stand . . . . . . . . . . . . . . . . . .10 Treatment of monitor cable . . . . . . . . . . . . . . . . . . . .11 Installation of monitor unit . . . . . . . . . . . . . . . . . . .11-12 Installation order for the stand (Rear seat monitor) . . .
Safety notes CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT SPLIT COVER(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user about the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
Safety notes Before you use the products, please read these instructions. When you use the products you must read all warnings and follow all the instructions. Keep this manual for future use. Warning Prohibition 1. Do not operate the unit while driving. Operating while driving may cause a fatal or serious accident. Always operate after the vehicle is parked at a safe place. 2. While driving, do not watch the monitor Watching TV or video while driving may cause a serious accident. 3.
Safety notes Notice Prohibition 1. Do not drop it and avoid heavy impact at anytime. This may be the cause of a trouble or a fire. 2. Do not watch TV or video for a long time with engine turned off. A vehicle may not start due to the discharge of battery. 3. Do not grab the lower part of the antenna to adjust an angle. 4. Do not charge, disassemble or heat the battery and keep it away from fire. This may be the cause of an explosion or a leakage. 5. Keep a glass washer out of children's reach.
Safety notes Notice 1 Compulsion Do not touch an antenna line or the monitor when lightning. This may be the cause of an electric shock. 2. In case that cable passes through a hole or touches a metal part, protect it appropriately. 3. Keep the battery out of children's reach. If a child swallows it, consult with a doctor right away. 4. While driving, keep the sound volume at a proper level. A loud sound may distract driving and it may be the cause of an accident. 5.
Main features This unit is designed to fit the environment of vehicles. Unlike general units for home Use, the unit for the Vehicles is equipped with a special circuit inside the product to provide good quality picture and sound. 1. Video Low reflection and high definition LCD Our LCD provides HD quality screen using 7 inch wide TFT LCD with 336,960 pixels. In addition, it has the pixel disposition structure suitable to watch screen during Navigation.
Main features 4. Convenient Functions Dimmer Function According to the brightness of surrounding, that of the screen can be adjusted. Up to 93 channel memory Our TV is capable of transmitting regular broadcasting TV (public) and automatically memorizes up to 93 channels for regular broadcasting TV stations. Remote Controller A user-friendly remote controller is provided. Auto Search Function Auto search function is designed to find next available TV station and to memorize the station automatically.
Installation Parts supplied AV Cable Earphone Section-mount cradle (Front) Cigar light adapter Section-mount cradle (Rear) Before installing At low temperature (20°C… or less) Turn on the heater for a proper temperature. (to enhance adhesive power). At high humidity (fog, rain and so on) After making adhesive side dried with a dryer, install the unit.
Installation Installation order for the Stand 1. Decide a place for installation and make a forming by bending the adhesive side of the Stand according to the shape of the place. 2. Wash the adhesive side cleanly with a neutral detergent or alcohol. 3. After uncovering a double-sided tape out of the Stand, install it. Double-sided tape Notice If the temperature of the adhesive side is low (20°C… or less), the adhesive power of the tape may be weaken. To prevent this, stick the Stand after heated. 4.
Installation Treatment of monitor cable Importance • If the Monitor is installed and the Cable connected, put the cable in a good order not to disturb a safe driving. • Pay attention to the cable not being caught in the rail of a door or a seat. The cable may be cut by its getting caught in. • Because it is very dangerous for the cable to be rolled up by a shift lever, arrange it well with a cable clamp.
Installation Adhere it on a place not to disturb the operation of air bags. Importance • Do not install on the place where disturbs front sight and the operating of steering, transmission shift lever, brake pedal and makes other passengers risky. This may be the cause of an accident or an injury. • As shown on the above, attach it on a safe place where it does not disturb front sight or you don't have to avert your eyes extremely.
Installation Installation order for the stand (Rear seat monitor) 1. First, separate the head rest A. Note Refer to your car’s user guide. 2. Insert the head rest A into the a hole placed on the up side of the section-mount cradle. 3. Install the head rest A into the a hole placed on the up side of the seat. 4. Drive the enclosed screws into the unit. 5. While putting the Stand screw into a hole placed on the bottom side of the unit, adjust installation height and angle.
Installation Connection of exterior units Rear View Camera, DVD, Video Camera, LDP, Player and etc. Connect it with a Cigar Jack. Can use to DC 9-12 V by Free Voltage employment. Note TV functions only for LAM-N760SP. When the AV Cable is insert and pulled out of the AV jack, the picture will flicker for a short moment, which is normal.
Parts name Front view 1 1. 2 3 4 5 6 7 8 9 : Power ON/OFF 2. • TV/AV : Mode conversion (TV t AV 1IN t AV 2 IN) : LAM-N760SP • AV1/AV2 : Mode conversion (AV 1IN t AV 2 IN) : LAM-N760 3. V : • Channel down select : LAM-N760SP • Down button / Menu item select 4. v : • Channel up select : LAM-N760SP • Up button / Menu item select 5. STBY (R) : Standby lamp (Red color) PWR (G ) : Power Lamp (Green color) 6. b : Volume up / Menu item adjust 7. B : Volume down / Menu item adjust 8. MENU : Enter menu 9.
Parts name Rear view 1 3 2 1. Left/ Right Speakers 2. TV Antenna (This functions only for LAM-N760SP.) 3. Docking connector Note Actual player may vary slightly from images shown.
Parts name Remote control 1. POWER 2. • TV/AV : Mode conversion (TV t AV1 IN t AV2 IN) : LAM-N760SP • AV1/1V2 : Mode conversion (AV1 IN t AV2 IN) : LAM-N760 1 2 4 5 3. A.MUTE (AUDIO MUTE) 4. • VOLUME UP U / DOWN u • Menu item adjust 5. • CHANNEL UP U / DOWN u : LAM-N760SP • Menu item select 6. MENU Battery installation 1. Remove the battery holder with a pencil or ball point pen. 2. Install the battery on the battery holder. 3. Install the battery holder back into its original position.
Operation Power ON/OFF STBY : RED PWR : GREEN • When connecting the power to the main system, red LED of STBY lights on. • Press the Power button, the ON/OFF can be repeatedly executed. • At the power ON, green LED of PWR lights on. Note When power of the main system is turned on or off, the picture sometimes flicker, which is normal. Mode conversion • Press the TV/AV (or AV) button repeatedly. Mode is changed. TV (LAM-N760SP) t AV1 IN t AV2 IN... • In " TV " display mode, a channel number displays.
Operation To enter the PICTURE menu 1. Press the TV/AV (or AV) button. Please select the AV1 IN or AV2 IN first. 2. Press the MENU button. Note When you press the AV1/AV2 switch, the picture will flicker for seconds, which is normal. PICTURE BRIGHTNESS CONTRAST SHARPNESS COLOR HUE A MODE DISPLAY ALL RESET 16:9 22 Adjusting PICTURE menu 1. Press the v or V buttons to select a item. 2. Press the b or B buttons to adjust.
Operation TUNING AUTO MEMORY 17.25 CHANNEL ADD/ERASE SOUND SYSTEM FINE TUNE AUTO MEMORY ALL RESET 01 ADD DK Press the b or B buttons to start auto search. All active channels will be preset and stored into the memory automatically. After presetting, the TV will go to the channel before the auto search starts. SOUND SYSTEM If the sound is abnormal, maybe the sound system setting is wrong. You can select a proper sound system as follow.
Operation FINE TUNE TUNING Fine tuning is unnecessary under normal conditions. However in areas of inferior broadcast conditions where adjustment is necessary for a better picture and sound, use FINE TUNE. 1. Press the v or V buttons to select the CHANNEL item. 2. Press the b or B buttons to select a channel number you want to fine tune. (For example, channel 10) 3. Press the v or V buttons to select the FINE TUNE item. 4.
Troubleshooting Check following points first before judging as trouble. Although you have checked following points, if a problem still remains, call the service center in this manual and we will take a proper action. (As this product is assembled in delicate parts, only a skilled technician is recommended for the disassembly of product.) Small red, blue and green points display on the screen. • LCD screen is made in a high technology. So, this may happen due to lack of pixels by 0.
Troubleshooting These cases are not the trouble. Under following cases, it is difficult to watch TV because TV receiving signal is bad. Screen Sound It noises. Environment Environment It noises. Between Buildings A power cable nearby At an airplane or a train passing nearby Deep in the mountains Field gets bad gradually. Color appears or disappears. Screen Sound Faded in double or triple Shaking It noises. Screen is spotted. Stripes appear. It noises.
Specifications Type.....................................................................................LCD color monitor Power supply ...................................................................................DC 9-12 V Consumption power .................................................................................15 W Receiving channel.........................................................................93 channels Operating temperature.........................................................
