ENGLISH LCD TV LED LCD TV OWNER’S MANUAL DVB is a registered trademark of the DVB Project ID Number(s): 6548 : 22LU50FD 6550 : 26LU50FD 6530 : 22LH20D 6531 : 26LH20D 6532 : 32LH20D 6533 : 37LH20D 6534 : 42LH20D 6535 : 32LH35FD 6536 : 37LH35FD 6537 : 42LH35FD 6538 : 32LH50YD 6539 : 37LH50YD 6540 : 42LH50YD 6541 : 47LH50YD 6542 : 55LH50YD 6545 : 42LH90QD 6546 : 47LH90QD 6680 : 37SL80YD 6679 : 42SL80YD 6678 : 47SL80YD 6677 : 55SL80YD 6947 : 42SL90QD 6948 : 47SL90QD LCD TV MODELS 22LU5*** 32LH5*** 26LU5*** 3
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Only 42/47SL9*** PO W ER ON/ EN ER GY 1 SAVIN 2 4 x4 0 NU MU RA TIO TE 20mm 16mm Bolts for stand assembly (Refer to p.15) Cable management clip (Refer to p.19) EN AD 9 P E Q.M /R T Q.V IEW MA FA RK/ V ME TV PU 6 8 LIS T OFF IN 3 5 7 x3 MOAV DE G G A x2 TV /IN PU T P U OK Cable Holder (Refer to p.
ACCESSORIES ■ Here shown may differ from your TV. POWER POWER ON/OFF POWER TV/RAD TV/RAD AV V MODE ENERGY SA SAVING VING LIST MARK MARK or FAV Owner’s Manual Batteries (Except 42/47SL9***) or FAV Q.VIEW or MUTE MENU ACCESSORIES Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. RETURN / EXIT Power Cord Q.MENU INFO This item is not included for all models.
CONTENTS ACCESSORIES ............................................ 1 PREPARATION CONTENTS Front Panel Controls..................................................... 4 Back Panel Information ................................................ 8 Stand Installation......................................................... 14 Not Using the Desk-type Stand ...............................16 Attaching the TV to a Desk .....................................17 Detaching Stand ...........................................
EPG (ELECTRONIC PROGRAMME GUIDE) (IN DIGITAL MODE) MHEG (MULTIMEDIA AND HYPERMEDIA INFORMATION CODING EXPERT GROUP) (IN DIGITAL MODE) Switch on MHEG......................................................... 95 Select a Programme.................................................... 95 Button Function in Listing Mode..............................96 Button Function in NOW/NEXT Guide Mode....... 96 PICTURE CONTROL Picture Size (Aspect Ratio) Control....................... 97 Picture Wizard .....................
PREPARATION FRONT PANEL CONTROLS CAUTION When the TV cannot be turned on with the remote control, press the main power button on the TV. (When the power is turned off with the main power button on the TV, it will not be turned on with the remote control). G Do not step on the glass stand or subject it to any impact. It may break, causing possible injury from fragments of glass, or the TV may fall. G Do not drag the TV. The floor or the product may be damaged.
■ Here shown may be somewhat different from your TV. Only 32/37/42LH4***, 32/37/42/47/55LH5*** PROGRAMME P VOLUME MENU MENU PREPARATION OK OK INPUT INPUT POWER Remote Control Sensor Intelligent Sensor Adjusts picture according to the surrounding conditions. OFF Power/Standby Indicator • Illuminates red in standby mode. • Illuminates blue when the TV is switched on.
PREPARATION ■ P Here shown may be somewhat different from your TV. Only 22/26LU5*** Only 26LU5*** Only 22LU5*** POWER INPUT MENU VOLUME OK PROGRAMME PROGRAMME P P INPUT MENU OK P VOLUME P PREPARATION OK OK MENU MENU INPUT INPUT POWER Main Power Switch ON Remote Control Sensor OFF Power/Standby Indicator Illuminates red in standby mode. Illuminates white when the TV is switched on.
■ Here shown may be somewhat different from your TV. Only 42/47SL9*** PROGRAMME PREPARATION P VOLUME OK OK MENU MENU INPUT INPUT POWER Remote Control Sensor Intelligent Sensor Adjusts picture according to the surrounding conditions. OFF ON Main Power Switch Power/Standby Indicator • Illuminates red in standby mode. • Illuminates white when the TV is switched on.
PREPARATION BACK PANEL INFORMATION ■ Here shown may be somewhat different from your TV.
■ Here shown may be somewhat different from your TV. Only 32/37/42/47/55LH5***, 42/47LH9*** ANTENNA IN 2 IN 4 1 1 4 3 2 5 RGB IN (PC) /DVI IN AUDIO IN 6 7 RS-232C IN (CONTROL&SERVICE) ANTENNA IN OPTICAL DIGITAL VIDEO L(MONO) AUDIO R (RGB/DVI) AUDIO OUT 7 AV IN1 VIDEO L/ L/MONO MONO AUDIO R VARIABLE AUDIO OUT 3 PREPARATION 10 2 2 1(DVI) AV IN2 1 VIDEO COMPONENT IN 2 HDMI/DVI IN Input Connect a HDMI signal to HDMI IN.
PREPARATION VIDEO Only 26LU5*** R Here shown may be somewhat different from your TV. VIDEO Only 22/26LU5*** 2 IN 3 ■ L(MONO) AUDIO L(MONO) AUDIO R ANTENNA IN ANTENNA IN PREPARATION ON 1 OFF 7 AV IN2 Only 26LU5*** 2 3 4 5 RGB IN (PC) 2 3 R 2 AUDIO VIDEO USB IN SERVICE ONLY L(MONO) L( MONO) AUDIO VIDEO ANTENNA IN 9 1 Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
Here shown may be somewhat different from your TV. Only 37/42/47/55SL8*** AV IN 2 4 3 2 5 DIGITAL AUDIO OUT AUDIO IN VIDEO L/ L/MONO MONO AUDIO R 1 VIDEO AUDIO ANTENNA IN COMPONENT IN 2 VIDEO L/MONO AUDIO R 1(DVI) VIDEO L/MONO AUDIO R ANTENNA IN ANTENNA IN 1 Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power. 2 HDMI/DVI IN Input Connect a HDMI signal to HDMI IN.
PREPARATION ■ Here shown may be somewhat different from your TV. Only 42/47SL9*** CAUTION PREPARATION IN 4 10 2 G Use a product with the following thickness for optimal connection to HDMI cable (only HDMI IN 4) / USB device.
■ Here shown may be somewhat different from your TV.
PREPARATION STAND INSTALLATION ■ Image shown may differ from your TV When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. PREPARATION Only 22LH2*** 1 2 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
■ Image shown may differ from your TV. Only 37/42/47SL8*** Only 42/47SL9*** Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Assemble the parts of the S t a n d B o d y with the S t a n d B a s e of the TV. 2 Assemble the parts of the S t a n d B o d y with the S t a n d B a s e of the TV.
PREPARATION NOT USING THE DESK-TYPE STAND ■ Here shown may be somewhat different from your TV. When installing the wall-mounted unit, use the protection cover. PREPARATION Only 22LH2*** 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. Only 26/32/37/42LH2***, 32/37/42LH3***, 32/37/42LH4***, 32/37/42/47/55LH5*** Insert the P R O T E C T I O N C O V E R into the TV until clicking sound. 2 Loose the bolts from TV.
ATTACHING THE TV TO A DESK (Only 26/32/37/42LH2***, 32/37/42LH3***, 32/37/42LH4***, 26LU5***, 32/37/42LH5***, 42LH9***) ■ Here shown may be somewhat different from your TV. Only 22/26LU5*** 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Loose the bolts and then detach the stand from TV. 1-Screw (provided as parts of the product) PREPARATION ■ Here shown may differ from your TV.
PREPARATION BACK COVER FOR WIRE ARRANGEMENT ■ Here shown may be somewhat different from your TV. Only 22LH2*** PREPARATION 1 2 Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Only 26/32/37/42LH2***, 32/37/42LH3***, 32/37/42LH4***, 32/37/42/47/55LH5***, 42/47LH9*** 1 Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section of the manual.
Only 22/26LU5*** After Connecting the cables as necessary, install CABLE HOLDER as shown and bundle the cables. Only 37/42/47/55SL8***, 42/47SL9*** FOR DESK-TYPE STAND Install the CABLE MANAGEMENT CLIP as shown. KENSINGTON SECURITY SYSTEM ■ ■ CABLE MANAGEMENT CLIP 2 Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. This feature is not available for all models. Image shown may differ from your TV.
PREPARATION POSITIONING YOUR DISPLAY CAREFUL INSTALLATION ADVICE (Only 22LH2***) Here shown may be somewhat different from your TV. ■ Adjust the position of the panel in various ways for maximum comfort. PREPARATION You should purchase necessary components to fix the TV safety and secure to the wall on the market. A Position the TV close to the wall to avoid the possibility of it falling when pushed.
! NOTE Should Install wall mount on a solid wall perpendicular to the floor. G Should use a special wall mount, if you want to install it to ceiling or slanted wall. G The surface that wall mount is to be mounted on should be of sufficient strength to support the weight of TV set; e.g. concrete, natural rock, brick and hollow block. G Installing screw type and length depends on the wall mount used. Further information, refer to the instructions included with the mount.
PREPARATION ■ To prevent damage do not connect to the mains outlet until all connections are made between the devices. ANTENNA CONNECTION ■ ■ For optimum picture quality, adjust antenna direction. An antenna cable and converter are not supplied.
EXTERNAL EQUIPMENT SETUP To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment. This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 32/37/42/47/55LH5*** models. ■ ■ Here shown may differ from your TV. ■ HD RECEIVER SETUP ■ This TV can receive Digital RF/Cable signals without an external digital set-top box.
EXTERNAL EQUIPMENT SETUP Connecting a set-top box with an HDMI cable OPTICA AUDIO IN /DVI IN Connect the digital set-top box to H D M I / D V I I N 1, H D M I I N 2 , H D M I I N 3 (Except for 22/26/32/37/42LH2***, 22LU5***) or H D M I I N 4 (Only 32/37/42/47/55LH5***, 42/47LH9***, 37/42/47/55SL8***, 42/47SL9***) jack on the TV. 1 3 (RGB/DVI) AUDIO 2 2 1(DVI) Y PB PR 1 EXTERNAL EQUIPMENT SETUP 2 Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.
DVD SETUP Connecting with a component cable 1 Connect the video outputs (Y, PB, PR) of the DVD to the C O M P O N E N T I N V I D E O jacks on the TV. 2 Connect the audio outputs of the DVD to the C O M P O N E N T I N A U D I O jacks on the TV. 3 Turn on the DVD player, insert a DVD. 4 Select C o m p o n e n t 1 input source using the I N P U T button on the remote control. If connected to C O M P O N E N T I N 2, select C o m p o n e n t 2 input source.
EXTERNAL EQUIPMENT SETUP Connecting the HDMI cable 1 EXTERNAL EQUIPMENT SETUP Connect the HDMI output of the DVD to the H D M I / D V I I N 1, H D M I I N 2 , H D M I I N 3 (Except for 22/26/32/37/42LH2***, 22LU5***) or H D M I I N 4 (Only 32/37/42/47/55LH5***, 42/47LH9***, 37/42/47/55SL8***, 42/47SL9***) jack on the TV.
VCR SETUP ■ To avoid picture noise (interference), allow adequate distance between the VCR and TV. Connecting with a RF Cable R L ANT OUT S-VIDEO ANT IN OUTPUT SWITCH VIDEO L R 1 EO MPONENT IN AUDIO ANTENNA IN 2 Wall Jack EXTERNAL EQUIPMENT SETUP PR Antenna VIDEO 1 Connect the A N T O U T socket of the VCR to the A N T E N N A I N socket on the TV. 2 Connect the antenna cable to the A N T I N socket of the VCR.
EXTERNAL EQUIPMENT SETUP Connecting with a RCA cable EXTERNAL EQUIPMENT SETUP 1 V I D E O jacks between TV and Connect the A U D I O/V VCR. Match the jack colours (Video = yellow, Audio Left = white, and Audio Right = red) 2 Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) 3 Select A V 1 input source using the I N P U T button on the remote control. If connected to A V 2 input, select A V 2 input source.
DIGITAL AUDIO OUT SETUP Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port. If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp). Connect one end of an optical cable to the TV Digital Audio (Optical) Output port.
EXTERNAL EQUIPMENT SETUP OTHER A/V SOURCE SETUP Camcorder Video Game Set RS-232C IN (CONTROL & SERVICE) AUDIO IN OPTICAL DIGITAL L/MONO AUDIO R AV IN1 VIDEO (RGB/DVI) AUDIO OUT VIDEO L R EXTERNAL EQUIPMENT SETUP 2 Y PB PR L R 1 VIDEO AUDIO ANTENNA IN COMPONENT IN 1 or Camcorder Video Game Set L R IN 4 VIDEO 1 AV IN2 1 V I D E O jacks between TV and external equipment. Match the jack colours .
USB SETUP (Except for 22/26/32/37/42LH2***, 32/37/42LH3***, 22/26LU5***, 32/37/42LH4***) IN 4 1 Connect the USB device to the U S B I N jacks on the TV. 2 After connecting the U S B I N jacks, you use the U S B function. (G p .
EXTERNAL EQUIPMENT SETUP PC SETUP This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. Connecting with a D-sub 15 pin cable AUDIO IN OPTICAL DIGITAL 2 Connect the PC audio output to the A U D I O I N ( R G B / D V I ) jack on the TV. DVI IN (RGB/DVI) AUDIO OUT VIDEO /MONO AUDIO 2 Y 3 Turn on the PC and the TV. PR PB VIDEO COMPONENT IN 4 Select R G B input source using the INPUT button on the remote control.
Connecting with a HDMI to DVI cable Connect the DVI output of the PC to the H D M I / D V I I N 1 jack on the TV. AUDIO IN /DVI IN (RGB/DVI) OPTICAL DIGITAL VID AUDIO OUT 3 2 Connect the PC audio output to the A U D I O I N ( R G B / D V I ) jack on the TV. 2 2 Y 1(DVI) PB PR 1 VIDEO COMPONEN 3 Turn on the PC and the TV. 4 Select H D M I 1 input source using the INPUT button on the remote control.
EXTERNAL EQUIPMENT SETUP Supported Display Resolution HDMI/DVI-DTV mode RGB-PC, HDMI/DVI-PC mode EXTERNAL EQUIPMENT SETUP Resolution Horizontal Frequency(kHz) Vertical Frequency(Hz) Resolution Horizontal Frequency(kHz) Vertical Frequency(Hz) 720x400 31.468 70.08 720x480 31.469/31.5 59.94/60 640x480 31.469 59.94 720x576 31.25 50 1280x720 50 59.94/60 33.72/33.75 59.94/60 28.125 50 37.879 60.31 48.363 60.00 1280x768 47.78 59.87 1360x768 47.72 59.80 1280x1024 63.595 60.
! NOTE G Avoid G If the graphic card on the PC does not output analogue and digital RGB simultaneously, connect only one of either RGB or HDMI IN (or HDMI/DVI IN) to display the PC output on the TV. G If graphic card on the PC does output analogue and digital RGB simultaneously, set the TV to either RGB or HDMI; (the other mode is set to Plug and Play automatically by the TV.) G DOS mode may not work depending on the video card if you use a HDMI to DVI cable.
EXTERNAL EQUIPMENT SETUP Screen Setup for PC mode Screen Reset Returns Position, Size and Phase to the factory default settings. This function works in the following mode : RGB[PC]. EXTERNAL EQUIPMENT SETUP PICTURE Move SCREEN OK E • Contrast 90 • Brightness 50 • Sharpness 70 • Colour 60 • Tint 0 Prev. Resolution Auto Config. Position R G Size • Advanced Control • Picture Reset Move To Set Yes No Phase Screen Screen Reset 1 MENU 2 Select P I C T U R E. OK Select S c r e e n.
Adjustment for screen Position, Size, Phase If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This function works in the following mode : RGB[PC]. Move SCREEN OK Move Prev. E • Contrast 90 • Brightness 50 • Sharpness 70 • Colour 60 • Tint 0 Resolution Auto Config.
EXTERNAL EQUIPMENT SETUP Selecting Resolution To view a normal picture, match the resolution of RGB mode and selection of PC mode. This function works in the following mode: RGB[PC] EXTERNAL EQUIPMENT SETUP SCREEN PICTURE Move Resolution E • Contrast 90 • Brightness 50 • Sharpness 70 • Colour 60 • Tint 0 Move Prev. OK Auto Config. 1024 x 768 1280 x 768 1360 x 768 Position R G Size • Advanced Control • Picture Reset Screen Screen 1 MENU 2 Phase Reset Select P I C T U R E.
Auto Configure (RGB [PC] mode only) Automatically adjusts the picture position and minimizes image instability. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment. PICTURE Move SCREEN OK E • Contrast 90 • Brightness 50 • Sharpness 70 • Colour 60 • Tint 0 Move Prev. Resolution Auto Config.
WATCHING TV / PROGRAMME CONTROL REMOTE CONTROL KEY FUNCTIONS (Only 32/37/42/47/55LH5***) When using the remote control, aim it at the remote control sensor on the TV. ENERGY SAVING Adjust the Energy Saving mode of the TV. RATIO Selects your desired Aspect Ratio of picture.(G p . 9 7) POWER Switches the TV on from standby or off to standby. INPUT External input mode rotate in regular sequence.(G p . 6 3) WATCHING TV / PROGRAMME CONTROL TV/RAD Selects Radio, TV and DTV channel. Q.
VOLUME UP Adjusts the volume. /DOWN MARK Select the input to apply the Picture Wizard settings. Check and un-check programmes in the USB menu. FAV Displays the selected favourite programme.(G p . 6 2) MUTE Switches the sound on or off. PAGE Move from one full set of screen information to the next UP/DOWN one. 0~9 number Selects a programme. button Selects numbered items in a menu. LIST Displays the programme List.(G p . 6 1) Q.VIEW Returns to the previously viewed programme.
WATCHING TV / PROGRAMME CONTROL REMOTE CONTROL KEY FUNCTIONS (Only 22/26/32/37/42LH2***, 32/37/42LH3***, 22/26LU5***, 32/37/42LH4***) When using the remote control, aim it at the remote control sensor on the TV. TV/RAD Selects Radio, TV and DTV channel. AV MODE It helps you select and set images and sounds when connecting AV devices.(G p . 6 8) POWER Switches the TV on from standby or off to standby.
VOLUME UP Adjusts the volume. /DOWN MUTE Switches the sound on or off. POWER AV V MODE ENERGY SAVING Programme Selects a programme. UP/DOWN SIMPLINK Controls SIMPLINK. control buttons LIST Q.VIEW MUTE Q. MENU Select the desired quick menu source. (Aspect Ratio, Clear Voice II , Picture Mode, Sound Mode, Audio, Sleep Timer, Favourite, Energy Saving.)(G p . 5 1) INFO i Shows the present screen information. GUIDE Shows programme schedule.(G p .
WATCHING TV / PROGRAMME CONTROL REMOTE CONTROL KEY FUNCTIONS (Only 42/47LH9***, 37/42/47/55SL8***) When using the remote control, aim it at the remote control sensor on the TV. POWER TV/RAD POWER Switches the TV on from standby or off to standby. POWER ON/OFF ON/OFF Key lighting on or off.(Only 42/47LH9***) WATCHING TV / PROGRAMME CONTROL TV/RAD TV/RAD Selects Radio, TV and DTV channel. ENERGY SAVING Adjust the Energy Saving mode of the TV. INFO i Shows the present screen information.
POWER VOLUME UP Adjusts the volume. /DOWN ON/OFF TV/RAD FAV Displays the selected favourite programme.(G p . 6 2) MARK Select the input to apply the Picture Wizard settings. Check and un-check programmes in the USB menu. Programme Selects a programme. UP/DOWN PAGE Move from one full set of screen information to the next UP/DOWN one. SIMPLINK / Controls SIMPLINK or USB menu(Photo List and Music USB Menu List or Movie List. control buttons MARK FAV See a list of AV devices connected to TV.
WATCHING TV / PROGRAMME CONTROL REMOTE CONTROL KEY FUNCTIONS (Only 42/47SL9***) When using the remote control, aim it at the remote control sensor on the TV. POWER Switches the TV on from standby or off to standby. ON/OFF Key lighting on or off. POWER ON/OFF TV/RAD Selects Radio, TV and DTV channel. TV/RAD AV MODE INPUT 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW ENERGY SAVING Adjust the Energy Saving mode of the TV. AV MODE It helps you select and set images and sounds when connecting AV devices.
POWER VOLUME UP Adjusts the volume. /DOWN ON/OFF MARK Select the input to apply the Picture Wizard settings. Check and un-check programmes in the USB menu. TV/RAD AV MODE INPUT 1 2 3 4 5 6 Programme Selects a programme. UP/DOWN 7 8 9 PAGE Move from one full set of screen information to the next UP/DOWN one. LIST 0 Q.VIEW FAV Displays the selected favourite programme.(G p . 6 2) ENERGY SAVING MUTE Switches the sound on or off. TELETEXT These buttons are used for teletext.
WATCHING TV / PROGRAMME CONTROL Simple Remote Control (Only 42/47SL9***) POWER Switches the TV on from standby or off to standby. TV/INPUT External input mode rotate in regular sequence.(G p . 6 3) TV/INPUT VOLUME UP Adjusts the volume. /DOWN WATCHING TV / PROGRAMME CONTROL MUTE Switches the sound on or off. Programme Selects a programme. UP/DOWN 0~9 number Selects a programme. button Selects numbered items in a menu. OK Accepts your selection or displays the current mode. OK Q.
TURNING ON THE TV - When your TV is turned on, you will be able to use its features. 1 Firstly, connect the power cord correctly and check the main power on the TV. At this stage, the TV switches to standby mode. 2 In standby mode to turn TV on, press the r / I, INPUT or P D E (or P ) button on the TV or press the POWER, INPUT, P or NUMBER button on the remote control and the TV will switch on.
WATCHING TV / PROGRAMME CONTROL PROGRAMME SELECTION 1 WATCHING TV / PROGRAMME CONTROL 50 Press the P number. or NUMBER buttons to select a programme VOLUME ADJUSTMENT 1 Press the + or - button to adjust the volume. If you wish to switch the sound off, press the MUTE button. You can cancel this function by pressing the MUTE, + , - or AV Mode button.
QUICK MENU Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently. F Aspect Ratio G 16:9 Except for 22/26/32/37/42LH2***, 32/37/42LH3***, 22/26LU5***, A u d i o : Selects the sound output. S l e e p T i m e r : Sets the sleep timer. F a v o u r i t e : Selects the favourite programme. U S B D e v i c e : Selects “Eject” in order to eject USB device.
WATCHING TV / PROGRAMME CONTROL ON SCREEN MENUS SELECTION AND ADJUSTMENT Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. A Here shown may differ from your TV.
AUTO PROGRAMME TUNING Use this to automatically find and store all available programmes. When you start auto programming, all previously stored service information will be deleted. The maximum number of programmes that can be stored is 500. But the number may differ slightly depending on broadcasting signals.
WATCHING TV / PROGRAMME CONTROL MANUAL PROGRAMME TUNING (IN DIGITAL MODE) Manual Tuning lets you manually add a programme to your programme list. SETUP Move SETUP OK Move F Auto Tuning Auto Tuning Manual Tuning Tuning Manual Manual Tuning Programme Edit Software Update : On Diagnostics OK DTV G Your receiver will add this channel to your channel list. Programme Edit UHF CH.
MANUAL PROGRAMME TUNING (IN ANALOGUE MODE) Manual Tuning lets you manually tune and arrange the stations in whatever order you desire. SETUP Move SETUP OK Auto Tuning Auto Tuning Manual Tuning Manual Tuning Programme Edit Move System : On Band Software Update Diagnostics G 3 Diagnostics BG V/UHF Channel 0 Search F G Name C 02 Store Close 1 MENU 6 Select S E T U P. Select V / U H F or C a b l e. 7 2 OK or Select M a n u a l T u n i n g.
WATCHING TV / PROGRAMME CONTROL SETUP Move OK SETUP Auto Tuning Auto Tuning Manual Tuning Manual Tuning Programme Edit Programme Edit Software Update : On Diagnostics Move OK F TV Storage Software Update G 3 : OnSystem BG Band V/UHF Diagnostics Channel 0 Search F G Name C 02 Store Close WATCHING TV / PROGRAMME CONTROL 56 A Assigning a station name You can assign a station name with five characters to each programme number. 1 MENU Select S E T U P.
PROGRAMME EDIT When a programme number is skipped, it means that you will be unable to select it using P viewing. button during TV If you wish to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the Programme edit menu. This function enables you to skip the stored programmes. You can change the programme number using “Move”function, if “Automatic Numbering” is unchecked when you start Auto Tuning.
WATCHING TV / PROGRAMME CONTROL IN DTV/RADIO MODE A Skipping a programme number 1 • When programmes are to be skipped, the skipped programme shows in blue and these programmes will not be selected by the P buttons during TV viewing. Select a programme number to be skipped. 2 BLUE Turn the programme number to blue. 3 • If you wish to select a skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or EPG. BLUE Release.
SOFTWARE UPDATE Software Update means software can be downloaded through the digital terrestrial broadcasting system. SETUP Move SETUP OK Auto Tuning Manual Tuning Manual Tuning Software Update On :: On Software Update Diagnostics Diagnostics 4 OK Save. * When setting “Software Update” Occasionally, a transmission of updated digital software information will result in the following menu on the TV screen. Software update is available.
WATCHING TV / PROGRAMME CONTROL DIAGNOSTICS This function enables you to view information on the Manufacturer, Model/Type and Software Version. This displays the information and signal strength of the tuned *MUX. This displays the signal information and service name of the selected MUX. (*MUX: A higher directory of channels in digital broadcasting (a single MUX contains multiple channels.)) Engineering Diagnostics SETUP Move Manufacturer : LG Electronics Inc. Model/Type : 42LH50YD Software Version : V3.
SELECTING THE PROGRAMME LIST You can check which programmes are stored in the memory by displaying the programme list. Mini Glossary Programme List Displayed when the Locked Programme. 1 TEN Digital 2 ABC TV Sydney 7 7 Digital Displaying programme LIST A 1 Display the Programme List. LIST A have been set up to be skipped in the programme edit mode. • Some programmes with the channel number shown in the programme LIST indicate there is no station name assigned.
WATCHING TV / PROGRAMME CONTROL FAVOURITE PROGRAMME SETUP A Selecting favourite programme Favorite programmes is a convenient feature that lets you quickly scan up to programmes of your choice without having to wait for the TV to scan through all the in-between programmes.
INPUT LIST HDMI and AV can be recognized by a detect pin and thus enabled only when an external device approves voltage. By using T V / R A D button, you can move from External Input to RF Input and to the last watched programme in DTV/RADIO/TV mode. 1 INPUT OK Select the input source.
WATCHING TV / PROGRAMME CONTROL INPUT LABEL Selects a label for each input source.
SIMPLE MANUAL You can easily and effectively access the TV information by viewing a simple manual on the TV. During the Simple Manual operation, audio will be muted. ■ OPTION Move Audio Language Subtitle Language Country OK : English : English WATCHING TV / PROGRAMME CONTROL Hard of Hearing( Image shown may differ from your TV. ) : Off : Austalia Input Label SIMPLINK : On Key Lock Simple Simple Manual Manual : Off E 1 MENU Select OPTION. 2 OK Select Simple Manual.
WATCHING TV / PROGRAMME CONTROL This function operates only with devices with the SIMPLINK logo. Please check the SIMPLINK logo. This TV might not function properly when using it with other products with HDMI-CEC function. This allows you to control and play other AV devices connected to the display through HDMI cable without additional cables and settings. O f f”.
Connecting to Home Theater with the SIMPLINK logo. 1 Connect the H D M I / D V I I N 1, H D M I I N 2 , H D M I I N 3 (Except for 22/26/32/37/42LH2***, 22LU5***) or H D M I I N 4 (Only 32/37/42/47/55LH5***, 42/47LH9***, 37/42/47/55SL8***, 42/47SL9***) terminal on the TV and the HDMI output terminal of the Home Theater using HDMI cables.
WATCHING TV / PROGRAMME CONTROL AV MODE You can select the optimal images and sounds when connecting AV devices to external input. Off Cinema Sport Game WATCHING TV / PROGRAMME CONTROL 1AV MODE Disables the AV MODE. Optimizes video and audio for watching movies. Optimizes video and audio for watching sports events. Optimizes video and audio for playing games. Off Cinema Game Sport Press the AV MODE button repeatedly to select the desired source.
INITIALIZING (RESET TO ORIGINAL FACTORY SETTINGS) This function initializes all settings. D a y and N i g h t of the P i c t u r e M o d e cannot be initialized. But the settings of It is useful to initialize the product or when you move to other city or country. When the Factory Reset is completed, you must restart the Initializing setup. O n", the message to enter the password appears.
TO USE THE BLUETOOTH (Only 42/47LH9***, 37/42/47/55SL8***, 42/47SL9***) Bluetooth? Bluetooth is a short distance networking technology using 2.4 GHz frequency to connect various types of information devices such as computers, cell phones and PDAs, as well as digital appliances through wireless connection, without having to connect any cable, to enable data exchange.
SETTING THE BLUETOOTH If you want to listen to the broadcasted sound using the Bluetooth headset or receive the jpeg images from an external device and view them on the TV, listen to music from cell phone(Bluetooth device), you can use the wireless communication without having to connect any cables. O n”. You can use the BLUETOOTH menu by selecting “O O f f”.
TO USE THE BLUETOOTH SET TV PIN To accept connection from an external Bluetooth device or to connect to an external Bluetooth device, the PIN needs to be entered. For details on how to set the PIN of the external Bluetooth device, refer to the user manual of the applicable device. The TV PIN is composed of numbers of up to 10 digits. The TV PIN must have more than 1 digit.
BLUETOOTH HEADSET When you select the Bluetooth headset, you can listen to the TV sound in the Bluetooth headset through wireless communication. You must pair it with any new Bluetooth device before the first use. For details, refer to the user manual of the applicable device. A maximum of 12 devices can be paired. When the unit is searching for the Bluetooth headset, other buttons except for the “Stop” (OK button) do not work.
TO USE THE BLUETOOTH Disconnecting the Bluetooth headset during use 1 MENU 3 Select B L U E T O O T H. OK Disconnect the Bluetooth headset. 2 OK OK Select B l u e t o o t h H e a d s e t. When requesting to connect to TV from the Bluetooth headset TO USE THE BLUETOOTH 74 When the Bluetooth menu is "On" and there is a connection request from the headset, this message is dispalyed. Not all headsets support the this feature.(Refer to the user manual of the applicable Bluetooth headset.
MANAGING REGISTERED BLUETOOTH DEVICE If there are no devices registered, Registered Bluetooth Device menu will be deactivated and cannot be used. When 12 devices are registered, you cannot register any more devices, and the external device will no longer be able to pair up with the TV. In this case, you should delete one (disconnect first if a device is connected to the TV) and then you can register another device.
TO USE THE BLUETOOTH MY BLUETOOTH INFORMATION This function provides the My Bluetooth Information to the user. "Edit" will be available when TV is not connected with any device. You can edit the My Device Name. You can check the My Device Address.
RECEIVING PHOTOS FROM EXTERNAL BLUETOOTH DEVICE For details on how to send photos(only JPEG) from the external Bluetooth device to TV, refer to the user manual of the applicable device. Receiving file(s) F 1/3 G E Close • When you select C l o s e with the button, the OSD will disappear. And when you press the OK button again, it will appear again. ■ (Rotate) : Rotate photos. Rotates the photo 90° clockwise upon O K button on (Rotate).
TO USE A USB DEVICE It is not possible to use USB function in 2 2 / 2 6 / 3 2 / 3 7 / 4 2 L H 2 * * *, 3 2 / 3 7 / 4 2 L H 3 * * *, 2 2 / 2 6 L U 5 * * * , 3 2 / 3 7 / 4 2 L H 4 * * * models. G When connecting a USB device When you connect a USB device, this pop up menu is displayed, automatically. “POP UP MENU” will not be displayed while the OSD including Menu, EPG or Schedule list is activated or while the Bluetooth Headset is connected.
PHOTO LIST You can view photo files on USB storage device. The On Screen Display may be different from your TV. Images are an example to assist with the TV operation. When you are watching the photo by the Photo List function, you can not change the picture mode. PHOTO(*.JPEG) supporting file Baseline : 64 x 64 ~ 15360 x 8640 Progressive : 64 x 64 ~ 1920 x 1440 • You can play JPEG files only. • Non-supported files are displayed in the form of predefined icon. Screen Components 2 OK Select U S B.
TO USE A USB DEVICE Photo Selection and PopUp Menu Photo List Page 2/3 Drive1 No Marked Up Folder KR103 09/10/2008 KR101 09/10/2008 KR104 09/10/2008 KR102 09/10/2008 KR105 09/10/2008 JMJ001 09/10/2008 JMJ005 09/10/2008 JMJ002 09/10/2008 JMJ006 09/10/2008 JMJ003 09/10/2008 JMJ007 09/10/2008 JMJ004 09/10/2008 JMJ008 09/10/2008 JMJ001 1366x768, 125KB Up Folder Navigation Popup Menu TO USE A USB DEVICE Photo List Page 2/3 Drive1 Page Change MARK KR101 Up Folder Navigatio
How to view photo Detailed operations are available on full-sized photo view screen.
TO USE A USB DEVICE 6 OK Select the Slideshow , B G M, D e l e t e , Option or H i d e. • Use (Rotate), button to select the previous or next photo. 1/17 Slideshow BGM Delete Option Hide • Use button to select and control the menu on the full-sized screen. TO USE A USB DEVICE G S l i d e s h o w : When no picture is selected, all photos in the current folder are displayed during slide show. If some photos are selected, those photos are displayed in a slide show.
MUSIC LIST You can play music files on USB storage device. Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files may not be supported by this model. Music file on your USB device can be played by this unit. The On Screen Display may be different from your TV. Images are an example to assist with the TV operation. MUSIC (*.MP3) supporting file Bit rate 32 ~ 320 • Sampling rate MPEG1 Layer3 : 32kHz, 44.1kHz, 48kHz • Sampling rate MPEG2 Layer3 : 16kHz, 22.
TO USE A USB DEVICE Music Selection and PopUp Menu As shown, up to 6 music titles are listed per page. P l a y (During stop) : Play the selected music titles. One playback of a piece of music finishes, the next selected one will be played. When there are no selected music titles to play, the next one in the current folder will be played. If you go to a different folder and press the O K button, the current music in playback will stop. G P l a y M a r k e d : Play the selected music titles.
■ If you don't press any button for a while during the playing, the play information box (as shown in the below) will float as a screen saver. ■ The ‘Screen Saver’? Screen saver is to prevent screen pixel damage due to an fixed image remaining on the screen for a extended period of time. ! NOTE TO USE A USB DEVICE When a music file is played, is displayed behind the title. G A damaged or corrupted music does not play but displays 00:00 in playtime.
TO USE A USB DEVICE MOVIE LIST You can play movie files on a USB storage device. The movie list is activated once USB is detected. It is used when playing movie files on TV. Displays the movies in the USB folder and supports Play. Allows playback of all movies in the folder and user desired files. It is a movie list that displays folder information and movie file. The On Screen Display may be different from your TV. Images are an example to assist with the TV operation. TO USE A USB DEVICE 86 Movie(*.
File Extension name mpg, mpeg, vob Video Decoder Audio Codec MPEG1, MPEG2 Dolby Digital, MPEG, MP3, LPCM MPEG1 Dolby Digital, MPEG, MP3, LPCM dat ts,trp,tp MPEG2, H.264/AVC Dolby Digital, AAC, MPEG mp4 MPEG4 SP, MPEG4 ASP, Divx 3.11, Dvix 4.12, Dvix 5.x Dolby Digital, HEAAC, AAC, Dvix 6, Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03 MPEG, MP3, LPCM Resolution (Max) Xvid 1.10 –beta1, Xvid 1.10-beta 2, H.264/AVC avi MPEG 2, MPEG 4 SP, MPEG4 ASP, Divx 3.
TO USE A USB DEVICE Movie Selection and PopUp Menu Movie List No Marked Page 2/3 movie Duration Title Up Folder 1:340, 120KB Up Folder Navigation Popup Menu Movie List Page Change MARK Mark Exit No Marked Page 2/3 movie 1366x768, 125KB Play Mark All Delete TO USE A USB DEVICE 1:340, 120KB Close Up Folder Navigation 1 2 Popup Menu Page Change MARK Mark Select the target folder or drive. Select the desired movie title OK 3 OK Play : Play the selected movie.
Using the Movie List function, play Picture Size F Full G 1 Audio Language Subtitle Language Off . Sync 0 . Position 0 Close P i c t u r e S i z e : Selects your desired picture format during movie play. G Audio Language & Subtitle Language : Changes the Language Group of the audio/subtitle during movie play. G S y n c : Adjusts the time synchronisation of the subtitle from -10 secs ~ +10 secs by steps of 0.5 secs during movie play.
TO USE A USB DEVICE DIVX REGISTRATION CODE Confirm the DivX registration code number of the TV. Using the registration number, movies can be rented or purchased at www.divx.com/vod. With a DivX registration code from other TV, playback of rented or purchased DivX file is not allowed. (Only DivX files matched with the registration code of the purchased TV are playable.) USB Move OK USB Photo List Photo List Music List Music List Movie List Movie List DivX DivXReg. Reg.Code Code DivX DivX Reg.
DEACTIVATION The purpose of deactivation is to allow deactivation of devices for users who have activated all the available devices through the web_server and are blocked from activating more devices. DivX VOD allowed the consumer to activate up to 6 devices under one account, but to replace or deactivate any of those devices, the consumer had to contact DivX Support and request deletion.
EPG (ELECTRONIC PROGRAMME GUIDE)(IN DIGITAL MODE) (Only Australia, Singapore and Indonesia) This system has an Electronic Programme Guide (EPG) to help your navigation through all the possible viewing options. The EPG supplies information such as programme listings, start for all available services. In addition, detailed information about the programme is often available in the EPG (the availability and amount of these programme details will vary, depending on the particular broadcaster).
Button Function in 8 Day Guide Mode Programme Guide 1 YLE TV1 ❉❚ ALL ❉❚ ❉❚ ❉❚ GREEN Enter Date setting mode. 14:00 15:00 Kungskonsumente Antigues Roadshow Mint Extra TV2: Farmen The Drum The Drum You Call The Hits Fashion Essentials ... ... ... Tänään otsikoissa 2 YLE TV2 ❉❚ ❉❚ 4 TV.. ❉❚ ❉❚ ❉❚ 5 YLE FST 6 CNN ❉❚ ❉❚ ❉❚ YELLOW Enter Timer Remind setting mode. Fri. 6. Apr. 1 YLE TV1 ❉❚ ❉❚ ❉❚ ❉❚ 8 YLE24 ❉❚ ❉❚ 6 Apr. 2007 15:09 E RED Change EPG mode. ...
EPG (ELECTRONIC PROGRAMME GUIDE)(IN DIGITAL MODE) Button Function in Extended Description Box ❉❚ Information Text Up/Down. ❉❚ 6 Apr. 2007 15:09 ❉❚ 6 Apr. 2007 YELLOW Enter Timer Remind setting mode. The detail information on or off. or GUIDE E Switch off EPG. INFO i Info. Exit Schedule Button Function in Remind Setting Mode Change to Guide or Schedule mode. Select the date to remind Select Remain. Function setting. Date Start Time Programme 15:09 That ’70s sh E 6 Mar.
MHEG (MULTIMEDIA AND HYPERMEDIA INFORMATION CODING EXPERT GROUP)(IN DIGITAL MODE) (Only New Zealand) This feature is enabled only in New Zealand. - In New Zealand, pressing the Guide key will display MHEG EPG provided by New Zealand on the screen. This system has an MHEG(Multimedia and hypermedia information coding expert group) to help your navigation through all the possible viewing options. Shows the present screen information. Displayed with a Teletext Programme. Displayed with a DTV Programme.
MHEG (MULTIMEDIA AND HYPERMEDIA INFORMATION CODING EXPERT GROUP)(IN DIGITAL MODE) Button Function in Listing Mode Select the Broadcast Programme Information. Select Channel. YELLOW Change to Next Week or Prev Day. BLUE Change to Next Day or Today. Next Week EPG/Guide OK GUIDE The MHEG will disappear after moving to a selected channel. 19 Change to Now/Next mode. Switch off MHEG. MHEG (MULTIMEDIA AND HYPERMEDIA INFORMATION CODING EXPERT GROUP) 96 Detail information on or off.
PICTURE CONTROL PICTURE SIZE (ASPECT RATIO) CONTROL You can watch the screen in various picture formats; 16:9, Just Scan, Original, 4:3, 14:9, Zoom and Cinema Zoom. If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible. You can adjust the enlarge proportion using button. This function works in the following signal. 1Q. MENU Select A s p e c t R a t i o. 2 • You can also adjust Aspect Ratio in the P I C- T U R E menu.
PICTURE CONTROL • 4:3 The following selection will allow you to view a picture with an original 4:3 aspect ratio, black bars will appear on both the left and right of the screen. • Zoom The following selection will allow you to view the picture without any alteration, while filling the entire screen. However, the top and bottom of the picture will be cropped. • 14:9 You can view a picture format of 14:9 or a general TV programme in the 14:9 mode.
PICTURE WIZARD This feature lets you adjust the picture quality of the original image. Use this to calibrate the screen quality by adjusting the Black and White Level etc. General users can calibrate the screen quality by easily following each stage. When you adjust the image to Low, Recommended or High, you can see the changed result as an example. In RGB-PC/HDMI-PC/DVI-PC mode, the changed Colour, Tint, Horizontal Sharpness and Vertical Sharpness values are not applied.
PICTURE CONTROL ENERGY SAVING It reduces the TV’s power consumption. The default factory setting complies with the E n e r g y S t a r requirements and is adjusted to the comfortable level to be viewed at home. You can increase the brightness of your screen by adjusting the E n e r g y S a v i n g l e v e l or by setting the P i c t u r e M o d e.
PRESET PICTURE SETTINGS Picture Mode-Preset Vivid Standard Natural Cinema Sport Game Strengthen the contrast, brightness, colour and sharpness for vivid picture. The most general screen display status. The most natural screen display status. Optimizes video for watching movies. Optimizes video for watching sports events. Optimizes video for playing games.
PICTURE CONTROL MANUAL PICTURE ADJUSTMENT Picture Mode-User option Backlight To control the brightness of the screen, adjust the brightness of LCD panel. Adjusting the backlight when setting the brightness of the set is recommended. Contrast Adjusts the signal level between black and white in the picture. You may use Contrast when the bright part of the picture is saturated. Brightness Adjusts the base level of the signal in the picture.
PICTURE IMPROVEMENT TECHNOLOGY You can calibrate the screen for each Picture Mode or set the video value according to the special video screen. You can set the video value differently for each input. To reset to the factory default screen after making adjustments to each video mode, execute the “Picture Reset” function for each Picture Mode. ■ Image shown may differ from your TV.
PICTURE CONTROL EXPERT PICTURE CONTROL By segmenting categories, E x p e r t 1 and E x p e r t 2 provide more categories which users can set as they see fit, offering the optimal picture quality for users. This may also be used to help a professional optimize the TV performance using specific videos. ■ Image shown may differ from your TV.
*This feature is not available for all models. Colour Temperature [Advanced Control] (Warm/Medium/Cool) ■ Choose one of three automatic colour adjustments. Set to warm to enhance hotter colours such as red, or set to cool to make picture bluish. ■ Adjusts the contrast to keep it at the best level according to the brightness of the screen. The picture is improved by making bright parts brighter and dark parts darker. ■ Adjusts screen colours so that they look livelier, richer and clearer.
PICTURE CONTROL • S t a n d a r d : Mode to reproduce original colour according to the standard of Colour Gamut (Wide/Standard) input signal independent of the display characteristics. • W i d e : Mode to use and set the rich colour area of the display. ■ Maximize the utilization for colour area that can be expressed. *This feature is not available for all models. Shows clearer and distinctive yet natural corners of the video. ■ This function is enabled in “Picture Mode - Cinema, Expert”.
PICTURE RESET Settings of the selected picture modes return to the default factory settings. PICTURE Move PICTURE OK Move E E 90 • Contrast 90 • Brightness 50 • Brightness 50 • Sharpness 70 • Colour 60 • Sharpness 60 ? All picture setting will be resetted. • Colour 60 continue? G • Tint 0 R • Tint 0 R G • Advanced Control • Advanced Control Yes PictureReset Reset ••Picture PictureReset Reset ••Picture Screen 1 MENU OK • Contrast No Screen 3 Select P I C T U R E.
PICTURE CONTROL POWER INDICATOR (Except 22/26LU5***, 22/26LH2***) It helps you adjust the brightness of moving LED and sound when power is turned on. Standby Light Determines whether to set the indicator light on the front of the TV to O n or O f f in standby mode. Power Light Determines whether to set the indicator light on the front of the TV to O n or O f f when the power turns on.
DEMO MODE Display the slide show to explain the various logo of this TV. It is not possible to use D e m o M o d e in H o m e U s e mode. In S t o r e D e m o, D e m o M o d e is automatically set to O n. Once D e m o M o d e is set to O f f in S t o r e D e m o, D e m o M o d e does not run and only the screen is reset. The screen is reset automatically after 5 minutes in D e m o M o d e.
PICTURE CONTROL MODE SETTING H o m e U s e ” mode for the best picture in your home environment. We recommend setting the TV to “H S t o r e D e m o ” mode is an optimal setting for displaying at stores.. “S ■ Image shown may differ from your TV.
SOUND & LANGUAGE CONTROL AUTO VOLUME LEVELER AVL automatically remains on the same level of volume if you change programmes. Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each programme.
SOUND & LANGUAGE CONTROL CLEAR VOICE II By differentiating the human sound range from others, it helps users listen to human voices better. AUDIO Auto Volume ClearVoice VoiceIIII Clear Move Auto Volume : Off Clear Voice II Off : :Off • Level Balance Sound Mode AUDIO OK 3 - + 0 L R Sound Mode : Standard : Off Off Off On 3 - + 0 L R : Standard • SRS TruSurround XT : Off • SRS TruSurround XT : Off • Treble 50 • Treble 50 • Bass 50 • Bass 50 Select A U D I O.
PRESET SOUND SETTINGS-SOUND MODE You can select your preferred sound setting; Standard, Music, Cinema, Sport or Game and you can also adjust the Treble, Bass. Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound options based on the programme content. Standard, Music, Cinema, Sport and Game are preset for optimum sound quality at the factory. Standard Music Cinema Sport Game Offers standard-quality sound. Optimizes sound for listening to music.
SOUND & LANGUAGE CONTROL SOUND SETTING ADJUSTMENT -USER MODE AUDIO Move Auto Volume Clear Voice II Auto Volume Clear Voice II : Off • Level Balance Sound Sound Mode Mode AUDIO OK : Off 3 - + 0 L R : :Standard Standard (User) Balance Sound Mode 2 OK : Off • Level 3 - 0 L + R Standard Standard (User) ::Standard Standard (User) • SRS TruSurround XT : Off Music • SRS TruSurround XT :Cinema Off • Treble 50 • Treble 50 Sport • Bass 50 • Bass 50 Game E E 1 MENU Move : Off
BALANCE You can adjust the sound balance of the speakers to preferred levels. AUDIO Move AUDIO OK Auto Volume : Off Auto Volume Clear Voice II : Off Clear Voice II • Level Balance Balance Sound Mode 3 - + 0 LL RR : Standard : Off • Level 3 L- Balance 00L L Balance Sound Mode OK : Off : Standard • SRS TruSurround XT : Off • SRS TruSurround XT : Off • Treble 50 • Treble 50 • Bass 50 • Bass 50 E 1 MENU Move R+ 0 R F R L R G Close E Select A U D I O.
SOUND & LANGUAGE CONTROL TV SPEAKERS ON/ OFF SETUP You can adjust the TV internal speaker status. In A V, C O M P O N E N T, R G B and H D M I 1 with HDMI to DVI cable, the TV speaker can be operational even when there is no video signal. If you wish to use an external Hi-Fi system, turn off the TV’s internal speakers.
SELECTING DIGITAL AUDIO OUT This function allows you to select your preferred Digital Audio Output. The TV can only output Dolby Digital if a channel is broadcast with Dolby Digital audio. When Dolby Digital is available, selecting Auto in the Digital Audio Out menu will set SPDIF(Sony Philips Digital InterFace) output to Dolby Digital. When Dolby Digital is not available, although Auto is selected in the Digital Audio Out menu, SPDIF output will be PCM(Pulse-code modulation).
SOUND & LANGUAGE CONTROL AUDIO RESET Settings of the selected Sound Mode return to the default factory settings. AUDIO Move AUDIO OK Move E 0 Sound Mode 1 MENU 2 OK E Balance OK L : Standard R Balance Sound Mode 0 L R : Standard • SRS TruSurround XT : Off • SRS TruSurround XT : Off • Treble 50 • Treble • Bass •• Reset Reset 50 50 Digital Audio Out : PCM • Bass 50 •• Reset Reset i Resetting sound mode configuration...
STEREO RECEPTION (IN ANALOGUE MODE ONLY) When a programme is selected, the sound information for the station appears with the programme number and station name. 1Q. MENU Select A u d i o. 2 Select the sound output. OK A Broadcast On Screen Display Mono MONO Stereo STEREO NICAM (Only Singapore, New Zealand and Indonesia) NICAM (Only Singapore, New Zealand and Indonesia) Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono.
SOUND & LANGUAGE CONTROL ON-SCREEN MENU LANGUAGE/COUNTRY SELECTION The installation guide menu appears on the TV screen when it is switched on for the first time. 1 OK Select your country. (Only Australia & New zealand) * If you want to change Country or Menu Language selection 1 MENU Select O P T I O N. 2 OK Select C o u n t r y(Only Australia & New zealand) or M e n u L a n g u a g e(Only Indonesia). OK Select your desired country or menu language.
LANGUAGE SELECTION (IN DIGITAL MODE ONLY) The Audio function allows selection of a preferred language. If audio data in a selected language is not broadcast, the default language audio will be played. Use the Subtitle function when two or more subtitle languages are broadcast. If subtitle data in a selected language is not broadcast, the default language subtitle will be displayed.
TIME SETTING CLOCK SETUP The clock is set automatically when receiving a digital signal. (You can set the clock manually only if the TV has no DTV signal.) You must set the time correctly before using on/off timer function. < Only Australia > When you select a Time Zone city, the TV time is set by the time offset information based on Time Zone and GMT (Greenwich Mean Time) which is received with the broadcast signal and the time is set automatically by a digital signal.
AUTO ON/OFF TIME SETTING The Off time function automatically switches the TV to standby at a preset time. Two hours after the TV is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed. The Off time function overrides the On time function if both are set to the same time. The TV must be in standby mode for the On time to work. TIME Move TIME OK Clock Move Clock Off Time : Off On Time Sleep Timer OK 1 Mar.
TIME SETTING SLEEP TIMER SETTING You do not have to remember to switch the TV off before you go to sleep. The sleep timer automatically switches the TV to standby after the preset time has elapsed. 1Q. MENU 2 Select S l e e p T i m e r. Select O f f, 1 0, 2 0, 3 0, 6 0, 9 0, 1 2 0, 1 8 0 or 2 4 0 m i n.. • When you switch the TV off, the preset sleep timer is cancelled. • You can also adjust S l e e p T i m e r in the T I M E menu.
PARENTAL CONTROL / RATINGS SET PASSWORD & LOCK SYSTEM Enter the password, press ‘0’, ‘0’, ‘0’, ‘0’ on the remote control handset. If a channel is locked, enter the password to unlock it temporarily. LOCK Move Lock LockSystem System OK :: Off Off Move Lock System Off ::Off Off Off Set Password Set Password On Block Programme Block Programme Parental Guidance : Blocking Off Input Block 1 MENU LOCK Select L O C K.
PARENTAL CONTROL / RATINGS BLOCK PROGRAMME Blocks any programme that you do not want to watch or that you do not want your children to watch. O n”. It is available to use this function in L o c k S y s t e m “O Enter a password to watch a blocked programme.
PARENTAL CONTROL (IN DIGITAL MODE ONLY) This function operates according to information from the broadcasting station. Therefore if the signal has incorrect information, this function does not operate. A password is required to gain access to this menu. This set is programmed to remember which option it was last set to even if you switch the set off. Prevents children from watching certain adult’s TV programmes, according to the ratings limit set. Enter a password to watch a blocked programme.
PARENTAL CONTROL / RATINGS EXTERNAL INPUT BLOCKING Enables you to block an input. O n”.
KEY LOCK The TV can be set so that the remote control is required to control it. This feature can be used to prevent unauthorized viewing.
TELETEXT This feature is not available in all countries. POWER ON/OFF TV/RAD POWER TV/RAD ENERGY SAVING SAVING AV V MODE Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programmes, share prices and many other topics. AV MODE INPUT ENERGY SAVING 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW LIST The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems.
FASTEXT The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button. A Page selection 1 2 3 4 Press the T . O P T button and then use button to select i menu. Display the index page. You can select the pages which are colour coded along the bottom line with corresponding coloured buttons. AS with SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER buttons in FASTEXT mode.
APPENDIX TROUBLESHOOTING The TV does not operate properly. Check to see if there is any object between the TV and the remote control causing an obstruction. Ensure you are pointing the remote control directly at the TV. A Ensure that the batteries are installed with correct polarity (+ to +, - to -). A Install new batteries. A The remote control does not work Power is suddenly turned off Is the sleep timer set? A Check the power control settings. Has the Power supply been interrupted.
The audio function does not work. A Picture OK & No sound A A A No output from one of the speakers + or - button. Press the Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly? A Adjust B a l a n c e in menu option. Unusual sound from inside the TV A A change in ambient humidity or temperature may result in an unusual noise when the TV is switched on or off and does not indicate a fault with the TV.
APPENDIX MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV. Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.
PRODUCT SPECIFICATIONS 22LH2*** 26LH2*** 32LH2*** 37LH2*** 22LH20D-AA 26LH20D-AA 32LH20D-AA 37LH20D-AA MODELS Dimensions (Width x Height x Depth) with stand 533.4 x 397.0 x 171.0 mm 21.0 x 15.7 x 6.8 inches 667.0 x 504.0 x 224.0 mm 26.3 x 19.9 x 8.8 inches 805.0 x 583.0 x 224.0 mm 31.7 x 23.0 x 8.8 inches 922.0 x 659.0x 297.0mm 36.3x 26.0 x 11.7 inches without stand 533.4 x 351.7 x 65.0 mm 21.0 x 13.9 x 2.6 inches 667.0 x 446.2 x 80.0 mm 26.3 x 17.6 x 3.2 inches 805.0 x 528.0 x 79.9mm 31.
APPENDIX 32LH5*** 37LH5*** 42LH5*** 47LH5*** 32LH50YD-AA 37LH50YD-AA 42LH50YD-AA 47LH50YD-AA MODELS Dimensions (Width x Height x Depth) with stand 815x 583.8x 223.8mm 32.1 x 23.0 x 8.8 inches 940.8 x 665.2x 296.2mm 1052.2 x 719.1 x 296.2mm 37.1x 26.2 x 11.7 inches 41.5x 28.3 x 11.7 inches 1173.4 x 789.7x 337.4mm 46.2x 31.1 x 13.3 inches without stand 815.0 x 529.6 x 82.0 mm 32.1 x 20.9 x 3.2 inches 940.8 x 603.5x 90.6mm 37.1x 23.8 x 3.6 inches 1052.2 x 657.3 x 90.8mm 41.5 x 25.9 x 3.
42LH9*** 47LH9*** 42SL9*** 47SL9*** 42LH90QD-AA 47LH90QD-AA 42SL90QD-AA 47SL90QD-AA with stand 1065.9 x 776 x 361.7 mm 42 x 30.5 x 14.2 inches 1179 x 851.4 x 398.8 mm 46.4x 33.5 x 15.7 inches 1009.2 x 694.5x 286.5mm 1119.6 x 757.1 x 286.5 mm 39.7 x 27.3 x 11.3 inches 44.1 x 29.8 x 11.3 inches without stand 1065.9 x 716.4 x 94.4 mm 1179 x 780.6 x 105.9 mm 46.4 x 30.7 x 4.2 inches 42 x 28.2 x 3.7 inches 1009.2 x 629.7x 29.3 mm 1119.6 x 691.3x 29.3 mm 44.1x 27.2 x 1.2 inches 39.7 x 24.8 x 1.
APPENDIX MODELS Dimensions with stand (Width x Height x Depth) without stand Weight with stand without stand Power requirement 32LH4*** 37LH4*** 42LH4*** 32LH40FD-AA 37LH40FD-AA 42LH40FD-AA 804.4 x 586.3 x 223.8 mm 31.7 x 23.1 x 8.8 inches 924.7 x 666.7x 296.2mm 36.4x 26.3 x 11.7 inches 1036.0 x 721.3 x 296.2 mm 40.8 x 28.4 x 11.7 inches 804.4 x 529.2 x 81.0mm 31.7 x 20.9 x 3.2 inches 924.7 x 599.9x 89.6mm 36.4x 23.6 x 3.5 inches 1036.0 x 655.4 x 89.8mm 40.8x 25.8 x 3.6 inches 12.
IR CODES ■ Image shown may differ from your TV. Code (Hexa) 95 08 0B 79 F0 45 43 AB 40 41 07 06 44 28 AA 30 02 03 1E 09 00 01 10~19 53 1A 72 71 63 61 20 21 39 7E Function Energy Saving POWER INPUT RATIO TV/RAD Q.MENU MENU GUIDE Up ( ) Down ( ) Left ( ) Right ( ) OK( ) RETURN/EXIT INFO i AV MODE + FAV ( MARK ) MUTE P P Number Key 0~9 LIST Q.VIEW RED Key GREEN Key YELLOW Key BLUE Key TEXT T.OPT(T.
APPENDIX EXTERNAL CONTROL DEVICE SETUP RS-232C Setup RS-232C IN (CONTROL & SERVICE) RGB IN (PC) AUDIO IN OPTICAL DIGITAL (RGB/DVI) AUDIO OUT VIDEO /MONO AUDIO AV IN 1 Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Note: RS-232C connection cables are not supplied with the product.
APPENDIX Set ID Use this function to specify a set ID number. Refer to ‘Real Data Mapping’. G p .145 OPTION Move OK OPTION E SIMPLINK : On Key Lock : Off Key Lock : Off ::11 Simple Manual Set ID ID Set ::11 Set ID ID Set OK E : On Simple Manual F 1 G Power Indicator Power Indicator Demo Mode : On Demo Mode : On Mode Setting : Store Demo Mode Setting : Store Demo Close Factory Reset Factory Reset 1 MENU Move SIMPLINK Select O P T I O N. 2 OK 3 OK Select S e t I D.
APPENDIX Communication Parameters Baud rate : 9600 bps (UART) A Data length : 8 bits A Parity : None Stop bit : 1 bit A Communication code : ASCII code A Use a crossed (reverse) cable. A A Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] Command Reference List COMMAND COMMAND DATA 1 2 (Hexadecimal) 01. Power 02. Aspect Ratio 03. Screen Mute 04. Volume Mute 05. Volume Control 06. Contrast 07. Brightness 08. Colour 09. Tint 10. Sharpness 11. OSD Select 12.
01. Power (Command: k a) 0 4 . V o l u m e M u t e (C o m m a n d : k e ) G To control Power On/Off of the set. G To control volume mute on/off. Transmission [k][a][ ][Set ID][ ][Data][Cr] You can also adjust mute using the MUTE button on remote control. Transmission Data 00 : Power Off Ack [k][e][ ][Set ID][ ][Data][Cr] 01 : Power On G To show Power On/Off.
APPENDIX 0 9 . T i n t (C o m m a n d : k j ) G To adjust the screen tint. You can also adjust tint in the PICTURE menu. 13. Treble (Command: k r) G To adjust treble. Transmission You can also adjust treble in the AUDIO menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] [k][r][ ][Set ID][ ][Data][Cr] Data Red : 00 ~ Green : 64 * Refer to ‘Real data mapping 1’. See page 145. Ack Data Min : 00 ~ Max : 64 * Refer to ‘Real data mapping 1’ See page 145.
17. Energy Saving (Command: j q) 19.Tune Command (Command: m a) G To reduce the power consumption of the TV. You can also G Select channel to following physical number. adjust Energy Saving in OPTION menu.
APPENDIX 21. Key(Command: m c) G To send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code - Refer to page 139. Ack [c][ ][Set ID][ ][OK/NG][Data][x] 2 3 . I n p u t s e l e c t (C o m m a n d : x b ) (Main Picture Input) G To select input source for main picture. Transmission [x][b][ ][Set ID][ ][Data][Cr] Data Structure MSB 0 22. Control Back Light (Command: m g) G To Control the back light.
Open source software notice The following GPL executables and LGPL/MPL libraries used in this product are subject to the GPL2.0/LGPL2.1/MPL1.1 License Agreements: GPL EXECUTABLES: • Linux kernel 2.6 • busybox • lzo LGPL LIBRARIES: • uClibc MPL LIBRARIES: • Nanox LG Electronics offers to provide source code to you on CD-ROM for a charge covering the cost of performing such distribution, such as the cost of media, shipping and handling upon e-mail request to LG Electronics at: opensource@lge.
APPENDIX OPEN SOURCE LICENSE GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
APPENDIX If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License.
NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
APPENDIX GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library".
APPENDIX Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
APPENDIX 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
MOZILLA PUBLIC LICENSE Version 1.1 --------------1. Definitions. 1.0.1. "Commercial Use" means distribution or otherwise making the Covered Code available to a third party. 1.1. "Contributor" means each entity that creates or contributes to the creation of Modifications. 1.2. "Contributor Version" means the combination of the Original Code, prior Modifications used by a Contributor, and the Modifications made by that particular Contributor. 1.3.
APPENDIX (b) under Patents Claims infringed by the making, using or selling of Original Code, to make, have made, use, practice, sell, and offer for sale, and/or otherwise dispose of the Original Code (or portions thereof). (c) the licenses granted in this Section 2.1(a) and (b) are effective on the date Initial Developer first distributes Original Code under the terms of this License. (d) Notwithstanding Section 2.
(b) Contributor APIs. If Contributor's Modifications include an application programming interface and Contributor has knowledge of patent licenses which are reasonably necessary to implement that API, Contributor must also include this information in the LEGAL file. (c) Representations. Contributor represents that, except as disclosed pursuant to Section 3.
APPENDIX 6.3. Derivative Works.
10. U.S. GOVERNMENT END USERS. The Covered Code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of "commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June 1995), all U.S. Government End Users acquire Covered Code with only those rights set forth herein. 11. MISCELLANEOUS.
