LCD TV OWNER’S MANUAL LCD TV MODELS 32LG53 37LG53 42LG53 Please read this manual carefully before operating your TV. Retain it for future reference. Record model number and serial number of the TV. Refer to the label on the back cover and quote this information. To your dealer when requiring service.
PREPARATION CHANNEL SETUP Accessories - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Setting Digital Channels - - - - - - - - - - - - - - - - - - - - - 37 Front Panel Controls - - - - - - - - - - - - - - - - - - - - - - - - 4 Setting Analog Channels - - - - - - - - - - - - - - - - - - - - - 43 Back Panel Information - - - - - - - - - - - - - - - - - - - - - - 5 Stand Install
PREPARATION Accessories Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. PREPERATION /WNERgS -ANUAL Owner's manual Owner’s Manual Batteries Remote Control or x4 x4 x1 (only 32LG53**) Power Cord Protection Cover Bolts for stand assembly (Refer to p.6) 1-screw for stand fixing (Refer to p.4) (Only 32/42LG53**) Polishing Cloth Polishing cloth for use on the screen.
Front Panel Controls ■ Image shown may differ from your TV. ■ If your TV has a protection film attached, remove the film and then wipe the TV with a polishing cloth. PREPERATION PROGRAMME VOLUME OK MENU INPUT Power/Standby Indicator • illuminates red in standby mode. • illuminates blue when the TV is switched on. Intelligent sensor Adjusts picture according to the surrounding conditions.
Back Panel Information ■ Image shown may differ from your TV. ➋ ➎ ➏ ➊ ➌ ➐ ➍ ➑ PREPERATION ➓ ➎ ➒ ➊ Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power. ➋ AUDIO IN (RGB/DVI) Connect the audio from a PC or DTV. ➌ OPTICAL DIGITAL AUDIO OUT (In Digital Mode only) Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work.
Stand Installation When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. ➌ Assemble the TV as shown. ➋ Assemble the parts of the Stand Body with the Cover Base of the TV.
Please set it up carefully so the product does not fall over. ■ You should purchase necessary components to fix the TV to the wall on the market. ■ Position the TV close to the wall to avoid the possibility of it falling when pushed. ■ The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage.
Back Cover for Wire Arrangement ➊ Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section of the manual. PREPERATION ➋ Open the CABLE MANAGEMENT CLIP as shown and manage the cables. ➌ Fit the CABLE MANAGEMENT CLIP as shown. CABLE MANAGEMENT CLIP NOTE ► Do not use the CABLE MANAGEMENT CLIP to lift the TV. If the TV is dropped, you may be injured or the TV may be damaged.
Desktop Pedestal Installation For adequate ventilation allow a clearance of 4” (10cm) all around the TV. 4 inches �� �� � 4 inches 4 inches � �� � �� � � � �� PREPERATION 4 inches � � Wall Mount: Horizontal Installation For adequate ventilation allow a clearance of 4” (10cm) all around the TV. We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.
Antenna or Cable Connection To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment. #/-0/.%.4 ). !6 !6 6)$%/ Antenna (Analog TV or Digital TV) !5$)/ ). /04)#!, $)')4!, 2'" $6) !5$)/ /54 ($-) $6) ). Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed.2'" ). 0# !5$)/ 6)$%/ , -/./ !5$)/ 2 PREPERATION 3 6)$%/ $6) 23 # ). #/.42/, 3%26)#% !.4%..
EXTERNAL EQUIPMENT SETUP ■ To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment. HD Receiver Setup Connecting with a component cable TV Connect the video outputs (Y, PB, PR) of the digital set top box to the COMPONENT IN VIDEO jacks on the TV. ➊ Connect the audio outputs of the digital set-top box to the COMPONENT IN AUDIO jacks on the TV. ➌ Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.
RGB OUTPUT Connecting with a HDMI to DVI cable ➊ TV Connect the digital set-top box to HDMI/DVI IN 1(DVI) jack on the TV. ➋ Connect the audio output of the digital set-top box to the AUDIO IN (RGB/ DVI) jack on the TV. ➌ Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) ➍ Select HDMI 1 input source using the INPUT button on the remote control.
DVD Setup Connecting with a component cable Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the TV. ➊ Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the TV. ➌ Turn on the DVD player, insert a DVD. (Refer to the DVD player’s manual for operating instructions.) ➍ Select Component input source using the INPUT button on the remote control. #/-0/.%.4 ).
VIDEO Connecting with a S-Video cable ➌ Turn on the DVD player, insert a DVD. (Refer to the DVD player’s manual for operating instructions.) Select AV3(S-Video) input source using the INPUT button on the remote control. VIDEO L/MONO AUDIO R EXTERNAL EQUIPMENT SETUP IN ➍ Connect the audio outputs of the DVD to the AUDIO input jacks on the TV. TV DVD PCMCIA CARD SLOT ➋ Connect the S-VIDEO output of the DVD to the S-VIDEO input jack on the TV. 9 VIDEO #/-0/.%.4 ).
VCR Setup ■ To avoid picture noise (interference), allow adequate distance between the VCR and TV. ■ If 4:3 picture format is used for an extended period the fixed images on the sides of the screen may remain visible. Connecting with a RF Cable TV VCR 3 6)$%/ !.4 ). /54054 37)4#( 6)$%/ , 2 !.4%..! ). Wall jack !.4%..! ). !.4 /54 3 6)$%/ !.4 ). /54054 37)4#( 6)$%/ , EXTERNAL EQUIPMENT SETUP !.4 /54 2 Antenna Connect the ANT OUT socket of the VCR to the ANTENNA IN socket on the TV.
2 RGB IN (PC) 1(DVI) AUDIO RS-232C IN (CONTROL & SERVICE) Connect the audio/video outputs of the VCR to the AUDIO/VIDEO jacks on the TV. Match the jack colours (Video = yellow, Audio Left = white, and Audio Right = red) S-VIDEO VIDEO L R ANT IN ➋ Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) ➌ OUTPUT ANT OUT Select AV3(CVBS) input source using the INPUT button on the SWITCH remote control.
Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white, and Audio Right = red) ➌ Operate the corresponding external equipment. (Refer to external equipment operating guide.) VIDEO L/MONO AUDIO R Select AV3(CVBS) input source using the INPUT button on the remote control.
RGB OUTPUT Connecting with a HDMI to DVI cable EXTERNAL EQUIPMENT SETUP GB-18 ➊ Connect the DVI output of the PC to the HDMI/DVI IN 1(DVI) jack on the TV. ➋ Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV. ➌ Turn on the PC and the TV. ➍ Select HDMI 1 input source using the INPUT button on the remote control. AUDIO TV HDMI/DVI IN AUDIO IN� (RGB/DVI) NOTE : ► To enjoy vivid picture and sound, connect a PC to the TV.
Supported Display Resolution PC mode HDMI1(DTV+PC) mode Horizontal Frequency(kHz) Vertical Frequency(Hz) Resolution Horizontal Frequency(kHz) Vertical Frequency(Hz) 720 x 400 31.468 70.08 720 x 400 31.468 70.08 640x480 31.469 37.5 59.94 75.00 640x480 31.469 37.5 59.94 75.00 800x600 37.879 46.875 60.317 75.00 800x600 37.879 46.875 60.317 75.00 1024 x 768 48.363 56.476 60.023 60 70.069 75.029 1024 x 768 48.363 56.476 60.023 60 70.069 75.029 1280x768 47.776 59.87 1280x768 47.
Scart Output Main Input AV1(SCART1 Output) Digital TV Digital TV Digital TV Digital TV-C Digital TV-C Digital TV-C Analog TV Analog TV Analog TV AV1(SCART1) AV1(CVBS) AV2(SCART2) AV2(CVBS) AV3(CVBS Side) EXTERNAL EQUIPMENT SETUP GB-20 AV2(SCART2 Output) AV3(S-VIDEO Side) Component PC AV3(CVBS) Last RF (Outputs the broadcast you watched last among Analog TV, Digital TV or Digital TV-C broadcast.
WATCHING TV/BASIC OPERATIONS Remote Control key Functions When using the remote control, aim it at the remote control sensor on the TV. POWER Switches the TV on from standby or off to standby. D/A Selects digital terrestrial, digital cable or analogue mode. INPUT Displays all available input sources. Switches the TV on from standby. TV/RAD Selects Radio or TV channel in digital mode. RATIO Selects your desired aspect ratio. VOL + / FAV MUTE P ∧/∨ WATCHING TV / BASIC OPERATIONS MENU Selects a menu.
Turning on the TV ➊ Firstly, connect the power cord correctly. At this stage, the TV switches to standby mode. ➋ In standby mode to turn TV on, press the , INPUT or PR ▲/▼ button on the TV or press the POWER, INPUT, P∧/∨ or NUMBER button on the remote control and the TV will switch on. Installation Wizard WATCHING TV / BASIC OPERATIONS When you turn on your TV for the first time after purchase or perform the default setting in Feature menu, the Installation wizard will appear automatically.
➍ Analog Channel Search It displays the default language, country and digital channel search result. Press the OK button to search the analog channels. Wizard Channel Search Language Countr y Terrestrial Channel Found Cable Channel Found Analog Channel Found Please wait for finishing the channel search. If you want to stop the operation during search, press the BACK button. English Finland 12 8 73 Scan Progress (AT V ) 87% The found channels are automatically saved in order.
Displaying Information Programme Information (i- plate) (In Digital Mode Only) Programme information (except the detailed programme information) is displayed for a certain period of time whenever you switch channels. You can view the programme information by pressing the INFO button while watching a programme. Press the INFO button again to hide the i-plate. The information is displayed as follows on the screen.
----1 ----34 : 34 ono Simple Information (except for Digital Mode) You can view the information such as the channel number (or input source), current time and sound information (or source resolution) by pressing the INFO or OK button while watching an analog TV channel or external input source. P 11 ----16 : 34 Mono ▲ Analog TV Input AV1 AV1 1616 : 34 : 34 ▲ External Input (Component, PC, HDMI1/2/3) NOTE ► Whenever you switch channels, this information is displayed for 5 seconds.
Displaying Channel List Digital Channel List (In Digital Mode Only) Three types of channel lists are provided for easy and quick channel browsing. TV The list of all Digital TV channels Radio The list of all Digital radio channels FAV-T or FAV-C The list of Digital favourite channels (Terrestrial or Cable) You can display channel list using the LIST button and switch to another channel on the channel list.
I/II Stereo/Dual Reception (In Analog Mode Only) Whenever you switch channels or press the INFO or OK button in analog TV mode, you can see the sound information of the current channel. Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono by pressing the I/II button twice. In mono reception, the clarity of sound is improved. To switch back to stereo, press the I/II button twice.
Setting the Subtitle (In Digital Mode Only) If the programme provides subtitle information you can select the language for the subtitle. ➊ Press the SUBTITLE button. ➋ Select a subtitle language using the ∧/∨ button and press the OK button. Then the subtitle will be displayed in the selected language at the bottom of the screen. Subtitle Norwegian ➌ Select Off from the subtitle language list to hide subtitle from the screen.
Selecting the Menu Language You can select the language for displaying menus and indications. ➊ Press the MENU button. ➋ Select Feature using the ∧/∨ button and press the OK or > button. ➌ Select the language of your choice using the button. The On Screen Display (OSD) menu will be shown in the selected language.
On-Screen Menus Picture Preferences > Picture Mode Brightness Contrast Sharpness Colour Back light Colour Temp.
Setting the Aspect Ratio You can select the modes by simply pressing the RATIO button on the remote control. Original > 4:3 > 14:9 > 16:9 > Zoom1 > Zoom2 4:3 When your TV receives a wide screen signal it will automatically change to the picture format broadcast. The following selection will allow you to view a picture with an original 4:3 aspect ratio, black bars will appear on both the left and right of the screen.
Displaying Teletext Information You can display teletext information at any time on your TV. Most TV broadcasting stations provide text information services via teletext. The index page of the teletext service gives you information on how to use the service. You can also select various options to fit your needs using the remote control buttons. NOTE ► To properly display teletext information, channel reception must be stable. Otherwise, information may be missing or some pages may not be displayed.
EPG (Electronic Programme Guide) (In Digital Mode Only) The EPG displays the programme information about each digital channel, based on the date and time. You can also schedule your watching using the information given. Press the GUIDE button to display the EPG. NOTE ► Press the EXIT or GUIDE button to exit the guide screen. Viewing the Electronic Programme Guide You can view programme information for all digital channels. Move to previous or next programme within the same channel using the button.
Viewing Using Time Bar You can quickly search the time zone using the time bar. ➊ Press the GREEN button to display time bar. ➋ Select the each button using the button and press the OK button to move the time bar. If you press the button repeatedly, the same operation is repeated. ➌ Each button functions as follows. EPG (Electronic Programme Guide) Now ◄ ► ◄◄ ►► ◄Day Day► Select ➍ Moves to the current programme where the cursor is located.
Finding a Programme You can sufficiently find the programme you want by programme name or genre. ➊ Press the BLUE button. ➋ Enter the programme name directly using the keyboard displayed on the screen. ➌ When entering programme name is complete, select Find and press the OK button. Find Programme by Name Keyword NOTE ➍ Select By Genre and press the OK button to search programme by genre. ➎ Select the genre using the ∧/∨/ button and press the OK button.
Viewing the Reserved Programme You can add or edit the reservation using the Schedule screen. Press the YELLOW button to display the schedule list. Adding a Reservation ➊ ➋ Select a blank space and press the OK button to add a new reservation schedule. Schedule Change Channel No. and Time using the NUMBER buttons. Reservation Channel No. ➌ EPG (Electronic Programme Guide) Change Repeat mode using the button. The options are Once, Daily and Weekly.
CHANNEL SETUP Setting Digital Channels (In Digital Mode Only) Digital channels can be searched and edited only in Digital TV or DigitalTV-C input mode. NOTE ► Press the BACK or < button to save the changes and return to the previous menu. Press the DTV SETUP or EXIT button to exit from the menu screen. ► You can easily select all menu items using the assigned number for each menu. ► The default password is 0000. If you have forgotten your password, please contact your local TV distributor.
Linear Search (In Digital TV-C Mode Only) You can search channels by setting the range of frequencies and other parameters. ➊ Press the DTV SETUP button. ➋ Select Installation using the ∧/∨ button and press the OK or > button. ➌ Select Installation (DTV-C) using the ∧/∨ button and press the OK or > button. ➍ Select Linear Search using the ∧/∨ button and press the OK or > button. ➎ Select Start/End Frequency using the ∧/∨ button and press the OK or > button.
Manual Search (In Digital TV Mode Only) You can search channels manually by searching parameters, using the MUX information. ➊ Press the DTV SETUP button. ➋ Select Installation using the ∧/∨ button and press the OK or > button. ➌ Select Installation (DTV-T) using the ∧/∨ button and press the OK or > button. ➍ Select Manual Search using the ∧/∨ button and press the OK or > button. ➎ Select Channel using the ∧/∨ button and press the OK or > button.
Manual Search (In Digital TV-C Mode Only) If your TV is connected to the cable and TV, you can search channels manually by searching parameters, if you know the MUX information. ➊ Press the DTV SETUP button. ➋ Select Installation using the ∧/∨ button and press the OK or > button. ➌ Select Installation (DTV-C) using the ∧/∨ button and press the OK or > button. ➍ Select Manual Search using the ∧/∨ button and press the OK or > button.
Edit Channel Lists ➊ Press the DTV SETUP button. ➋ Select Edit Channels using the ∧/∨ button and press the OK or > button. ➌ Select Edit Channel Lists using the ∧/∨ button and press the OK or > button. ➍ You will be prompted to enter your password. Enter your password using the NUMBER buttons. ➎ To select the channel list group, press the OK or > button in Group and then select a group using the ∧/∨ and OK button.
Edit Favourite Channels ➊ Press the DTV SETUP button. ➋ Select Edit Channels using the ∧/∨ button and press the OK or > button. ➌ Select Edit Favourite Channels using the ∧/∨ button and press the OK or > button. The buttons for editing favourite channel list are described in the following table. Add Adds favourite channel. Remove Removes from favourite channel. TV/Radio Switches between TV and radio channel list. Move Moves the order of channel list within favourite channel list.
Setting Analog Channels (In Analog Mode Only) Analog channels can be searched and edited only in Analog TV input mode. Automatic Search You can automatically search channels for the frequency ranges available (availability depends on your region). Press the MENU button. ➋ Select Installation using the ∧/∨ button and press the OK or > button. ➌ Select Auto Search using the ∧/∨ button and press the OK or > button. Search is highlighted. ➍ Press the OK button to start to search channels.
Manual Search You can save each channel as you identify. ➊ Press the MENU button. ➋ Select Installation using the ∧/∨ button and press the OK or > button. ➌ Select Manual Search using the ∧/∨ button and press the OK or > button. Colour System is highlighted. > Installation Countr y Auto Search Manual Search Edit Channels Finland Move ➍ ➎ ➏ Select the required broadcasting standard (Auto, PAL, or SECAM) using the button. Select Audio System using the ∧/∨ button.
Edit Channels After channel searching completes, you can delete, skip, move or add into favorite channel group the saved analog channels. ➊ Press the MENU button. ➋ Select Installation using the ∧/∨ button and press the OK or > button. ➌ Select Edit Channels using the ∧/∨ button and press the OK or > button. The Edit Channels menu will appear. Skipping Channels Once channels are selected to skip, you can select the skipped channels using number buttons only.
PICTURE SETTINGS Selecting a Picture Mode You can select the picture mode which best fits your viewing requirements. ➊ Press the MENU button. ➋ Select Picture using the ∧/∨ button and press the OK or > button. ➌ Select the required picture mode using the button. The following options are available: Standard > Cinema > Sport > Game > Intelligent sensor > User > Picture Mode Brightness Contrast Sharpness Colour Back light Colour Temp.
Noise Reduction If the signal received by your television is weak, you can activate this feature to help reduce noise that may appear on the screen. ➊ Press the MENU button. ➋ Select Picture using the ∧/∨ button and press the OK or > button. ➌ Select NR using the ∧/∨ button. ➍ Select the required option by pressing the button. The following options are available. > Picture Mode Brightness Contrast Sharpness Colour Back light Colour Temp.
SOUND SETTINGS Setting the Sound Effect You can select the type of special sound effect when watching a broadcast. Sound Effect lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the programme content. ➊ Press the MENU button. ➋ Select Sound using the ∧/∨ button and press the OK or > button. ➌ Select Effect using the ∧/∨ button and press the OK button.
Adjusting the Volume Automatically Each broadcasting station has its own signal conditions, volume may not be adjusted each time you switch channels. This feature lets you automatically adjust the volume of the selected channel by adjusting the sound output depending on the signal modulation. ➊ Press the MENU button. ➋ Select Sound using the ∧/∨ button and press the OK or > button. ➌ Select AVL(Auto Volume Level) using the ∧/∨ button. ➍ Select On/Off using the button.
FEATURE SETTINGS Setting the Time Information You can set the current time. If you want to set time for automatically turning on/off the power, you must set the local time first. Setting the Current Time ➊ Press the MENU button. ➋ Select Feature using the ∧/∨ button and press the OK or > button. ➌ Select Time Setting using the ∧/∨ button and press the OK or > button.
Setting the PC (In PC Mode Only) The PC menu is available only when there is a PC input signal. Press the INPUT button to switch to PC mode. Select PC using the ∧/∨ button and press the OK button. Press the MENU button. Select Feature using the ∧/∨ button and press the OK or > button. Select PC using the ∧/∨ button and press the OK or > button. Auto Configure >> PC Auto Configure H. Position V. Position Clock Phase XGA Mode Automatically optimizes the display.
XGA Mode >> PC Auto Configure H. Position V. Position Clock Phase XGA Mode To view a normal picture, match the resolution of XGA mode and the resolution of PC. Select XGA Mode using the ∧/∨ button. Select the desired resolution. 1024 x 768 > 1280 x 768 > 1360 x 768 > 1366 x 768 0 0 0 53 1024 x 768 Adjust Move Setting the Screen (In Component or HDMI Mode Only) The Screen menu is available only when there is a HDMI (DTV format: 480p/720p/1080i/1080p) input signal.
DTV SETUP (In Digital Mode Only) This chapter describes how to set up the DTV Setup menu for digital channels. You can set the options such as the parental control, channel editing, installation setting and software upgrade. > DT V Setup DT V Setup NOTE ► The DTV Setup menu is available in the Digital TV or Digital TV-C input mode only. To access the DTV Setup menu, select DTV Setup on TV menu and press the OK button while in the Digital mode.
Censorship Classification Censorship Classification allows you to block programmes according to the age level you have set. ➊ Select Censorship Classification using the ∧/∨ button and press the OK or > button. Parental Control View All Censorship Classification ➋ Select the required age level using the ∧/∨ button and press the OK button. View All 7 ~ 18 Lock All 7 Change Password 12 15 All programmes can be watched because there is no age limitation.
Language Setting ➊ Press the DTV SETUP button. ➋ Select Preferences using the ∧/∨ button and press the OK or > button. Language Setting Primary Audio Language Secondary Audio Language Audio Priority Primary Subtitle Language ➌ Select Language Setting using the ∧/∨ button and press the OK or > button.
Subtitle Font You can select the subtitle font. ➊ Select Subtitle Font using the ∧/∨ button. ➋ Select from Variable and Fixed using the OK or ► button. Variable Uses the horizontally variable subtitle font. Fixed Uses the fixed subtitle font. Hard of Hearing Subtitles You can set whether or not to use the hard of hearing subtitles. ➊ Select Hard of Hearing Subtitles using the ∧/∨ button and press the OK or > button. ➋ Select from Enable/Disable using the OK or > button.
Miscellaneous Settings ➊ Press the DTV SETUP button. ➋ Select Preferences using the ∧/∨ button and press the OK or > button. Miscellaneous Settings Display Time Option in CH List ➌ Select Miscellaneous Settings using the ∧/∨ button and press the OK or > button. 5 Sec On i-Plate Display Time You can set the duration of the information box to be displayed when you switch the channel. ➊ Select i-Plate Display Time using the ∧/∨ button and press the OK or > button.
Software Update In order to maintain proper performance of the TV, it is essential to have the most up-to-date software. OTA (Over the Air) OTA, an abbreviation of Over–the-Air, means that the software can be downloaded through your aerial. The manufacturer reserves the right to decide when and where to release software by this process. The software update via your aerial will only occur under the following circumstances. ➊ The equipment should have appropriate loader software.
Automatic Update You can set the TV to find software update site and update software automatically. ➊ Press the DTV SETUP button. ➋ Select Installation using the ∧/∨ button and press the OK or > button. ➌ Select Installation (DTV-C) or Installation (DTV-T) using the ∧/∨ button and press the OK or > button. Installation (DTV-C) Antenna Setting Linear Search ➍ Select Software Update using the ∧/∨ button and press the OK or > button.
Manual Update (In Digital TV-C Mode Only) You can perform manual update using know MUX information. ➊ Press the DTV SETUP button. ➋ Select Installation using the ∧/∨ button and press the OK or > button. ➌ Select Installation (DTV-C) using the ∧/∨ button and press the OK or > button. ➍ Select Software Update using the ∧/∨ button and press the OK or > button. ➎ Select Manual Update using the ∧/∨ button and press the OK or > button.
System Status ➊ Press the DTV SETUP button. ➋ Select System using the ∧/∨ button and press the OK or > button. ➌ Select Status, Signal Detection or Common Interface using the ∧/∨ button and press the OK or > button. System Status You can view system information. Status Signal Detection Common Interface Signal Detection You can view the signal strength and signal quality of the channel that is currently on AV. Common Interface You can view the current status of the CI-Module.
APPENDIX Menu Map Picture Mode Brightness Contrast Sharpness Colour Backlight Colour Temp.
Troubleshooting The TV does not operate properly. The remote control does not work - Check to see if there is any object between the TV and the remote control causing an obstruction. Ensure you are pointing the remote control directly at the TV. - Ensure that the batteries are installed with correct polarity (+ to +, - to -). - Install new batteries. Power is suddenly turned off - Is the sleep timer set? - Check the power control settings. Has the Power supply been interrupted.
Maintenance Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV. Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen ➊ A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it is almost dry, and then use it to wipe the screen.
