Removing the optional finisher Printing To remove the optional finisher, its bins, and its stand, complete the following sections. Paper handling Preparing for disassembly 1 Turn the power off. Maintenance 2 Remove all print media from the bins. Removing the bins Troubleshooting 1 Grasp the top bin (bin 1) and tilt it up. Administration Index www.lexmark.
Removing the optional finisher Printing 2 Pull the bin straight out Paper handling Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher Printing 3 Loosen the two screws under the bottom bin (bin 2). Paper handling Maintenance Troubleshooting Administration Index 4 Lift the bin and pull it straight out. 5 Set the bins aside. www.lexmark.
Removing the optional finisher Printing Disconnecting the finisher from the printer Paper handling 1 Push the finisher release latch. Maintenance Finisher release latch Troubleshooting Administration Index 2 Push the finisher away from the printer. Note: The finisher slides to the right while still on its stand. www.lexmark.
Removing the optional finisher Printing 3 Locate the cable connecting the transport unit to the finisher. Paper handling Maintenance Troubleshooting Administration Index 4 Loosen the two thumbscrews on each side of the connector. 5 Disconnect the plug from the finisher. www.lexmark.
Removing the optional finisher Printing 6 Locate the finisher power cable on the printer. 7 Press down on the tab on the cable plug, and then pull the plug out. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher Printing 8 Locate the other end of this cable in the lower of the three connectors. 9 Pull the plug straight out. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher Printing 10 Disconnect the finisher cable from the back of the printer Paper handling Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher 9 Printing 11 Locate the other end of this cable in the middle connector on the back of the finisher. Paper handling Maintenance Troubleshooting Administration Index 12 Loosen the thumbscrews on each side of the plug, and pull the plug straight out. www.lexmark.
Removing the optional finisher Printing Removing the finisher from the stand Paper handling CAUTION! This procedure should be completed by two people to avoid injury. Ask someone to help you move the finisher. 1 Hold down the left side of the black lever on the bottom rear of the stand. Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher Printing 2 Have someone push the finisher away from the printer until it slides off the stand. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher 12 Printing Removing the divertor cover Paper handling 1 Pull the two tabs on the divertor cover straight out using a flat blade screwdriver or a flat key. Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher Printing 2 Rotate the divertor cover up and over toward the standard bin to release it. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher Printing Removing the transport unit Paper handling 1 While supporting the transport unit, swing the two vertical support levers up. They snap into place in the bottom of the transport unit. Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher Printing 2 Gently lower the transport unit into its vertical position. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher 16 Printing 3 Grasp the transport unit on each side, and then lift it straight up and off the finisher. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher Printing Disassembling the stand Paper handling The finisher stand consists of two metal pieces. The guide rail holding plate is attached directly to the printer. The guide rail is attached to guide rail holding plate. 1 Loosen the two screws on the guide rail. Maintenance 2 Pull the guide rail away from the guide rail holding plate and set it aside. Guide rail holding plate Troubleshooting Administration Index Guide rail www.lexmark.
Removing the optional finisher Printing 3 Loosen the two screws on the guide rail holding plate. 4 Pull the guide rail holding plate off, and set it aside. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher Printing Removing the finisher plate Paper handling 1 Loosen the screws on the finisher plate attached to the right side of the printer. 2 Pull the finisher plate straight off. Maintenance Troubleshooting Administration Index www.lexmark.
Removing the optional finisher 20 Printing 3 Reattach the stacking arm. See Reinstalling the stacking arm for more information. 4 Turn the printer on. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.
