Installation Guide

ManualsBrandsLeviton ManualsSmart Home15 Amp 120-Volt Decora Digital Switch and Timer with Bluetooth Technology

Testing your Switch prior to mounting in wall box:

Switch Mounting:

TURN OFF POWER AT

CIRCUIT BREAKER OR FUSE.

3-Way Wiring with DD0SR-DL Matching Remote

(with LED) Application:

DI-000-DDS15-02A

• Restore power at circuit breaker or fuse.

• Press pad until locator light is OFF. Lights

should turn ON.

If lights do not turn ON, refer to the

TROUBLESHOOTING section.

Step 5

For additional information, contact Leviton’s

Techline at 1-800-824-3005 or visit Leviton’s

website at www.leviton.com

• Position all wires to provide room in outlet

wall box for device.

• Ensure that the word “TOP” is facing up on

device strap.

• Partially screw in mounting screws in wall

box mounting holes.

NOTE: Dress wires with a bend as shown

in diagram in order to relieve stress when

mounting device.

Step 6

Installation may now be completed by tightening

mounting screws into wall box. Attach wallplate.

Restore Power:

Restore power at circuit breaker or fuse.

Installation is complete.

Step 7

Step 4c

SwitchMatching Remote (with LED)

Terminal

Screw

marked

Black

(BK)

Terminal

Screw marked

Red (RD)

Terminal

Screw marked

White (WH)

Terminal

Screw

marked

Yellow/

Red

(YL/RD)

Terminal

Screw marked

Red (RD)

Neutral to Terminal

Screw marked

White (WH)

YL/RD

erminal

Screw

marked

Black

(BK)

erminal

Screw

marked

Yellow/

Red

(YL/RD)

Hot (Black)

Neutral (White)

Load

YL/RD

YL/RDRD

Black

White

Line

120/277 VAC

60Hz

WH BK

Matching Remote (with LED)

Switch

Green

Ground

Green

Ground

(unused)

NOTE: The switch must be installed in a wall box that has a Load

connection. The matching remote must be installed in a wall box with

a Line Hot connection and a Neutral connection. A Neutral wire to the

matching remote needs to be connected as shown.

If you are unsure about any part of these instructions, consult an

electrician.

NOTE: Maximum wire length from switch to all installed remotes cannot

exceed 300 ft (90 m).

WIRING MATCHING REMOTE (wall box with line hot

connection):

Connect wires per WIRING DIAGRAM as follows:

NOTE: "RD" terminal on matching remote is unused. Tighten screw.

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot (common) wall box wire identiﬁed (tagged) when removing

old switch and First Traveler to Remote terminal marked BK.

• Second Traveler wall box wire from switch to remote terminal screw

marked "YL/RD" (note wire color). This traveler from the remote must

go to Yellow/Red switch terminal screw.

• Line Neutral wall box to remote terminal screw marked "WH".

WIRING SWITCH (wall box with load connection):

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Load wall box wire identiﬁed (tagged) when removing old switch to

Red terminal screw.

• First Traveler Line Hot to Black terminal screw.

• Remove Red insulating label from Yellow/Red terminal screw.

• Second Traveler wall box wire (note color as above) to Yellow/Red

terminal screw. This traveler from the switch must go to the terminal

screw on the remote marked "YL/RD".

• Line neutral wall box wire to White terminal screw.

• Proceed to Step 5.

NOTE: The locator light will illuminate when the load is in the OFF position

to facilitate access in the dark.

Push Pad (Default settings)

Turn ON from OFF position:

Tap top of rocker – Lights turn ON.

Turn OFF from ON position:

Tap bottom of rocker – Lights turn OFF.

If there is a power outage, when the power is restored, the lights will return

to the last setting before the power interruption.

Cleaning: Clean with a damp cloth. DO NOT use chemical cleaners.

OPERATION

TROUBLESHOOTING

• Lights Flickering

- Lamp has a bad connection.

- Wires not secured ﬁrmly under terminal screws of switch and/or

remote.

• Light does not turn ON and Locator LED does not turn ON

- Circuit breaker or fuse has tripped.

- Lamp is burned out.

- Neutral not wired to switch (white wire).

- Lamp Neutral connection is not wired.

• Remote does not operate lights

- Ensure that total wire length does not exceed 300 ft (90 m).

- Ensure wiring is correct.

Push Pad

Locator

Light

FOR CANADA ONLY

For warranty information and/or product returns, residents

of Canada should contact Leviton in writing at Leviton

Manufacturing of Canada Ltd to the attention of the Quality

Assurance Department, 165 Hymus Blvd, Pointe-Claire

(Quebec), Canada H9R 1E9 or by telephone at 1-800-405-5320.

NOTE: To pair your switch with your mobile device, download the

Leviton Decora® Digital Switch and Timer app from the Google

Play Store or your iTunes account. Contact Leviton’s Techline at

1-800-824-3005 or visit Leviton’s website at www.leviton.com for

additional information.

This device complies with Part 15 of the FCC Rules. Operation is subject

to following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation of the device.

This equipment has been tested and found to comply with the limits for

a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment OFF and ON, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving Antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/tv technician for help.

FCC CAUTION

Any changes or modiﬁcations not expressly approved by Leviton

Manufacturing Co., Inc., could void the user's authority to operate the

equipment.

FCC COMPLIANCE STATEMENT

Download the Leviton Decora

Digital Switch & Timer App for your

device.

Android: Tap the Google Play Store icon on your phone or go to

http://play.google.com on your computer and follow the

instructions to obtain the app.

iPhone: Tap the App Store icon on your phone or access the app

through your iTunes account on your computer.

Once you have downloaded the app, follow the instructions on the screen

to pair your mobile device with your switch. Once your mobile device is

paired, use the following options to control your switch:

• On - Off: Turns the switch ON and OFF.

• Schedule: Creates distinct ON/OFF events based on time and day.

• Sleep Timer: Sets countdown to turn switch OFF.

Advanced Settings

Device Options

• Randomized Scheduled Events: Cycles lights ON and OFF to

ensure a "lived-in" look while away.

• Hide Status LED: Turns Status LED OFF.

• DST Offset Hours: Adjusts the Sunrise/Sunset time in hours.

• DST Offset Minutes: Adjusts the Sunrise/Sunset time in minutes.

CONTROLLING YOUR DIMMER WITH BLUETOOTH

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the beneﬁt of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for ﬁve years from the purchase date. Leviton’s only obligation

is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in

an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and ﬁtness for a

particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and ﬁtness for a particular purpose, is limited to ﬁve years. Leviton is not liable for incidental, indirect, special, or consequential

damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

This product is covered by U.S. Patent No. 8,664,886 and corresponding

foreign patents.

The Bluetooth

word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc., used under license by Leviton.

Use herein of third party trademarks, service marks, trade names, brand

names and/or product names are for informational purposes only, are/may

be the trademarks of their respective owners; such use is not meant to

imply afﬁliation, sponsorship, or endorsement.

No part of this document may be reproduced, transmitted or transcribed

without the express written permission of Leviton Manufacturing Co., Inc.

IC COMPLIANCE STATEMENT

This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of

the device.