Installation Guide

ManualsBrandsLeviton ManualsSmart Home15 Amp 120-Volt Decora Digital Switch and Timer with Bluetooth Technology

WARNINGS AND CAUTIONS

• Use only (1) Decora Digital DDS15 Switch in a multi-location circuit with up to 9 coordinating remote switches (DD0SR-10)

or up to 4 matching remote switches (DD0SR-DL)

• Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft (90m).

• Recommended minimum wall box depth is 2-3/4".

• Use this device with copper or copper clad wire only.

3-Way Wiring with DD0SR-10 Coordinating Remote

(no LED) Application:

Preparing and connecting wires:

This switch can be wired using side wire terminal screws or

through backwire openings. Choose appropriate wire stripping

speciﬁcations accordingly.

WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN

OFF POWER at circuit breaker or fuse and test that power is off

before wiring!

Identifying your wiring application (most common):

NOTE: If the wiring in your wall box does not resemble any of

these conﬁgurations, consult an electrician.

Single Pole (One location) or 3-Way (Multi-location)

Universal Electronic Switch and Program Timer

Cat. No. DDS15-BD, (Lighted) - 120/277VAC, 60Hz

1800W Incandescent (120V) – 15A Fluorescent (120V) – 6A Fluorescent (277V)

5A, 600W LED/CFL (120V) – 15A Resistive (120V) – 1/2 HP Motor (120V)

INSTALLATION INSTRUCTIONS

DI-000-DDS15-02A

TOOLS NEEDED TO INSTALL YOUR SWITCH

Slotted/Phillips Screwdriver Electrical Tape Pliers

Pencil Cutters Ruler

Changing the color of your Switch:

Your switch includes three color options. The switch ships with the White

frame attached. To change color of frame, proceed as follows:

INSTALLING YOUR SWITCH

NOTE: Use check boxes when Steps are completed.

ONOFF

ONOFFONOFF

ONOFF

Step 1

Single Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

3-Way

1. Line or Load

(see

important instruction)

2. Neutral

3. Ground

4. First Traveler – note color

5. Second Traveler – note

color

Step 2

IMPORTANT : For 3-Way applications, note that one of the screw terminals

from the old switch being removed will usually be a different color (Black)

or labeled Common. Tag that wire with electrical tape and identify as the

common (Line or Load) in both the switch wall box and remote wall box.

Terminal

Screw marked

Black (BK)

Terminal

Screw marked

Red (RD)

Terminal Label:

Use terminal for 3-way or more applications only.

For single-pole applications, DO NOT remove label.

Terminal

Screw marked

White (WH)

Terminal

Screw marked

Yellow/Red

(YL/RD)

YL/RD

Single Pole Wiring Application:

Step 4a

Step 3

• Make sure that the ends of the wires from the wall box are

straight (cut if necessary).

• Remove insulation from each wire in the wall box as shown.

• For Single-Pole Application, go to Step 4a.

• For 3-Way Coordinating Remote (no LED) Application, go to Step 4b.

• For 3-Way Matching Remote (with LED) Application, go to Step 4c.

5/8"

(1.6 cm)

Strip Gage

(measure bare

wire here)

Cut

(if necessary)

Side Wire Connection

Side wire terminals accept #14-12

AWG solid copper wire only.

Back Wire Connection

Back wire openings accept #14-12

AWG solid copper wire only.

Hot (Black)

Neutral (White)

Load

Switch

Black

White

Green

Ground

YL/RD

Line

120/277VAC,

60Hz

Use terminal for

3-way or more

applications only.

For single-pole

applications,

DO NOT remove label.

WIRING SWITCH:

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot wall box wire to terminal screw marked "BK".

• Load wall box wire to terminal screw marked "RD".

• Line Neutral wall box wire to terminal screw marked "WH".

•

Switch terminal screw marked "YL/RD" should have Red insulation label afﬁxed.

NOTE: If insulating label is not afﬁxed to terminal screw marked "YL/RD", use

electrical tape to cover.

• Proceed to Step 5.

• Switch ON/OFF

• ON/OFF LED Indicator

• Three way communication

• Ease of installation – No new wiring

The next generation of lighting control technology is here with

the new Decora

Digital Switch with Bluetooth

Technology. This

innovative device works using the Leviton Decora

Digital Dimmer &

Timer app that can be easily downloaded to smartphones or tablets

and paired to the Leviton Switch using Bluetooth

technology.

Decora

Digital Devices give users point-to-point local control to

automate lighting, bridging the gap between standard switches and

whole-house automation systems.

Enjoy the combined functions of a standard wall switch and

a countdown or programmable timer switch in one attractive

device. Use of the app allows greater ﬂexibility for accurate timer

functionality and makes pushing buttons for timed events a tedious

chore of the past.

The Leviton Decora

Digital Dimmer & Timer app can be easily

downloaded to mobile devices and is compatible with Android and

iOS smartphones or tablets. The app is easy to use with simple,

intuitive on-screen menu options to independently control Decora

Digital dimmers and switches throughout the home.

Decora

Digital Devices are ideal for living rooms, bedrooms,

kitchens, dining rooms, home ofﬁces, outdoor lighting or anywhere

full control of lighting is desired.

FEATURES

INTRODUCTION

SwitchCoordinating Remote (no LED)

Terminal

Screw

marked

Black (BK)

Terminal

Screw marked

Red (RD)

Terminal

Screw marked

White (WH)

Terminal

Screw

marked

Yellow/Red

(YL/RD)

Terminal

Screw marked

Yellow/Red (YL/RD)

YL/RD

Neutral to Terminal

Screw marked

White (WH)

3 3

5 5

Terminal

Screw

marked

Black (BK)

Terminal

Screw

marked

ellow/Red

(YL/RD)

Green

Ground

Green

Ground

Hot (Black)

Neutral (White)

Coordinating Remote (no LED)

YL/RD

Black

White

Line

120/277V

60Hz

(unused)

Load

Switch

Step 4b

Step 4b cont’d

NOTE: The switch must be installed in a wall box that has a Line

Hot connection. The coordinating remote must be installed in a wall

box with a Load connection and a Neutral connection. A Neutral

wire to the coordinating remote needs to be added as shown. If

you are unsure about any part of these instructions, consult an

electrician.

NOTE: Maximum wire length from switch to all installed remotes

cannot exceed 300 ft (90 m).

WIRING SWITCH (wall box with line hot connection):

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot (common) wall box wire identiﬁed (tagged) when

removing old switch to terminal screw marked "BK".

• First Traveler wall box wire to terminal screw marked "RD"

(note wire color).

• Remove Red insulating label from terminal screw marked

"YL/RD".

• Second Traveler wall box wire to terminal screw marked

"YL/RD" (note wire color). This traveler from the switch must go

to the terminal screw on the remote marked "YL/RD".

• Line Neutral wall box wire to terminal screw marked "WH".

WIRING COORDINATING REMOTE (wall box with load

connection):

Connect wires per WIRING DIAGRAM as follows:

NOTE: "BK" and "RD" terminals on coordinating remote are

unused. Tighten both screws.

• Green or bare copper wire in wall box to Green terminal screw.

• Load wall box wire identiﬁed (tagged) when removing old switch

to First Traveler (note color as above).

• Second Traveler wall box wire (note color as above) to terminal

screw marked "YL/RD". This traveler from the remote must go to

the terminal screw on the switch marked "YL/RD".

• Remove White insulating label from terminal screw marked

"WH".

• Line Neutral wall box wire to terminal screw marked "WH".

• Proceed to Step 5.

WARNINGS AND CAUTIONS

• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!

•

TO AVOID FIRE, PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT install to control a receptacle.

• To be installed and/or used in accordance with electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

• The Decora

DDS15 is not compatible with standard 3-way or 4-way switches. It must be used with the Decora

Digital DD0SR-DL or DD0SR-10 remote for

multi-location dimming.

Insert top

tabs and

press in

bottom

tabs to

attach

Push in

sides at

bottom tabs

and pull

outward to

release

Summary of content (2 pages)

PAGE 1
Single Pole (One location) or 3-Way (Multi-location) Universal Electronic Switch and Program Timer Cat. No.
PAGE 2
Step 4c 3-Way Wiring with DD0SR-DL Matching Remote (with LED) Application: Matching Remote (with LED) BK Terminal Screw marked White (WH) YL/RD Terminal Screw marked Yellow/ Red (YL/RD) Terminal Screw marked Black (BK) 2 WH 1 4 RD Terminal Screw marked Yellow/ Red (YL/RD) 3 5 Terminal Screw marked Red (RD) BK WH 2 4 YL/RD RD 1 3 5 Terminal Screw marked Red (RD) Switch Matching Remote (with LED) Hot (Black) WH BK WH BK RD YL/RD RD YL/RD Black Line 120/277 VAC 60Hz (unused) Gree