Install Instructions

ManualsBrandsLeviton ManualsElectrical Enclosures & BoxesPop-Up Floor Box w/ Tamper-Resistant Self-Test GFCI Outlet, 20A

POP-UP RECEPTACLE

Cat. Nos. PFUS1, PFUS2, PFTR1, PFTR2, PFGF1, PFGF2

INSTALLATION INSTRUCTIONS ENGLISH

DI-000-PFXXX-05B

WARNINGS

• TO AVOID FIRE, SHOCK OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER

OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!

• TO AVOID RISK OF ELECTRIC SHOCK, ALL NON-GFCI RECEPTACLES MUST BE

GFCI PROTECTED.

• IF WATER ENTERS THE ASSEMBLY, TURN POWER OFF AT THE CIRCUIT

BREAKER and replace the unit immediately.

CAUTIONS

• Install and/or use in accordance with appropriate electrical codes and regulations.

• Use only the electrical mounting box provided.

• Use indoors only. Not for use in wet locations, such as kitchen or bathroom countertops.

• For surfaces greater than 2 1/4" thick. (5.72 cm), use the overmount installation.

• If you are unsure about any part of these instructions, consult an electrician.

• Use this device with copper or copper clad wire only.

Includes:

mounting brackets (2)

and screws (4)

protective cover and

screws (2)

Box 26mm screws (2)

Also includes one of the following assembly lids

RESET

TEST

Before you install the pop-up receptacle

• Check under ﬂooring to make sure there is enough clearance to accommodate the

box assembly.

• Choose a mounting site where the top of the surface is smooth and free of dirt and

surface irregularities.

• If there are surface irregularities, consider using a ﬂexible sealant between

mounting surface and pop-up assembly.

Installation

1. Choose template and installation method

• For ﬂoors with access underneath, use undermount installation (See Template A), included.

• For surfaces greater than 2 1/4" thick. (5.72 cm), use the overmount installation (See Template B), included.

• For concrete installation, cut ﬁnished ﬂooring to the size of the box.

2a. Undermount Installation of Box

• Use Template A to cut opening.

• Remove the knockouts furthest from the front of the

box. Pull the conductors through, leaving 6" (15.2 cm)

inside of the box.

• Secure mounting brackets to underside of ﬂooring

using appropriate screws (not provided).

NOTE: 1/8" to 1/4"

below nished

ooring.

2b. Overmount Installation of Box

• Use Template B. Rout the hatched areas 3/16" deep

in the subﬂooring.

• Remove the knockouts furthest from the front of the

box. Pull the conductors through, leaving 6" (15.2 cm)

inside of the box.

• Secure mounting brackets to routed area using

appropriate screws (not provided).

• Install ﬁnished ﬂooring. NOTE: When ﬁnished

ﬂooring is installed, the box should be 1/8" to 1/4"

below the surface of the ﬁnished ﬂooring.

Suboor

NOTE: 1/8" to 1/4"

below nished ooring.

Suboor

Finished Flooring

Pop-Up Assembly with

Tamper Resistant

Self-Test GFCI

Cat. No.

PFGF1

Cat. No.

PFGF2

15A-125V 20A-125V

Pop-Up Assembly

with Tamper Resistant

Receptacle

Cat. No.

PFTR1

Cat. No.

PFTR2

15A-125V 20A-125V

Pop-Up Assembly with

Duplex USB Charger/

Tamper Resistant

Receptacle

Cat. No.

PFUS1

Cat. No.

PFUS2

15A-125V 20A-125V

Summary of content (2 pages)

PAGE 1
POP-UP RECEPTACLE Cat. Nos. PFUS1, PFUS2, PFTR1, PFTR2, PFGF1, PFGF2 WARNINGS • TO AVOID FIRE, SHOCK OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING! • TO AVOID RISK OF ELECTRIC SHOCK, ALL NON-GFCI RECEPTACLES MUST BE GFCI PROTECTED. • IF WATER ENTERS THE ASSEMBLY, TURN POWER OFF AT THE CIRCUIT BREAKER and replace the unit immediately. DI-000-PFXXX-05B CAUTIONS • Install and/or use in accordance with appropriate electrical codes and regulations.
PAGE 2
c. Concrete Installation of Box • Attach conduit and position box. NOTE: The top of the floor box should extend above the poured concrete if additional flooring will be used. When finished flooring is installed, the floor box should be 1/8" to 1/4" below it. NOTE: After conduit is connected, make sure 6" (15.2 cm) of cable or wire is available inside box for wiring. • Attach protective plastic cover and block any open holes. • Pour concrete and let it cure. • Remove the protective cover.