Instructions / Assembly

ManualsBrandsLeviton ManualsCircuit Breaker LockoutsCircuit Breaker Manual Transfer Interlock Accessory Kit

PK-A3218-10-00-0B

For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only)

1 800 405-5320 (Canada Only) www.leviton.com

PK-A3218-10-00-0B

INSTALLATION INSTRUCTIONS

Nos. LP3xx-MC, LP4xx-MC

Outdoor Meter - Load Center Combination Enclosure

INSTALLATION

WARNING: TO AVOID FIRE, SHOCK OR

DEATH: TURN OFF POWER SUPPLYING

THIS EQUIPMENT, AND CONFIRM POWER

IS OFF, before installing, removing or

servicing this equipment.

Step 1: Remove meter and wiring

compartment covers

(ﬁg. 1)

a. Remove Meter cover (B) by loosening

the securing screw (J) and sliding cover

down and out.

b. Remove wiring compartment cover (C)

by loosening the securing screw (K) and

sliding security latch (A) upward and

sliding cover out and down.

c. Slide wiring compartment cover (C)

up and out.

Step 2: Remove Load Center Door (Optional)

NOTE: The load center door can be removed for

easier installation.

a. Lift door (D) upward to remove from

hinge (E) (ﬁg. 2).

b. When installation is complete, align the

door hinge (E) with the hinge pin and insert

downward until door is seated.

Step 3: Bottom Feed Wiring

NOTE: Before removing any knockouts from the

enclosure, consult the local electrical code to

determine the knockout requirements.

a. To remove knockouts (F), ﬁrst strike the center

of the knockout.

b. Pry each ring (G) up, one at a time, and grip

both ends with a pair of pliers.

c. Use the pliers to bend the rings (G) until they

disconnect from the enclosure (ﬁg. 3).

Step 4: Enclosure Mounting

Surface Mounting

Remove deadfront (S) by loosening the securing

screw (T) and lifting the deadfront (S) off the

enclsoure.

b. Remove

mounting knockouts (H) from the back

of the enclosure (ﬁg. 4).

c. Use outdoor approved screws or nails (not

provided) in the mounting

knockouts

(H) to

secure the enclosure to the wall.

Fig. 1

Fig. 3

Fig. 2

Fig. 4

IMPORTANT SAFETY INSTRUCTIONS - READ ALL INSTRUCTIONS BEFORE USING.

PATENTS PENDING

LIMITED PRODUCT WARRANTY

For Leviton’s limited product warranty, go to www.leviton.com. For a printed copy of the warranty you may call 1-800-323-8920.

WARNING

• TO AVOID FIRE, SHOCK OR DEATH: TURN OFF POWER SUPPLYING THIS EQUIPMENT, AND CONFIRM POWER IS OFF,

before installing, removing or servicing this equipment.

• This equipment MUST BE installed and serviced by an electrician.

• Replace all doors and covers before connecting power to this equipment.

• To be installed and/or used in accordance with electrical codes and regulations.

Knockout

(F)

Ring

(G)

Ring

(E)

Mounting

Knockouts

(H)

Down

Meter

cover

(B)

Wiring

compartment

cover

(C)

Down

Out

Hinge pin

Hinge (E)

Door (D)

Securing

latch (A)

Screw

(K)

Screw

(J)

Meter cover (B)

Wiring

compartment

cover (C)

WEB VERSION

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Outdoor Meter - Load Center Combination Enclosure PK-A3218-10-00-0B Nos. LP3xx-MC, LP4xx-MC IMPORTANT SAFETY INSTRUCTIONS - READ ALL INSTRUCTIONS BEFORE USING. WARNING • TO AVOID FIRE, SHOCK OR DEATH: TURN OFF POWER SUPPLYING THIS EQUIPMENT, AND CONFIRM POWER IS OFF, before installing, removing or servicing this equipment. • This equipment MUST BE installed and serviced by an electrician. • Replace all doors and covers before connecting power to this equipment.
PAGE 2
Step 5: Phase, Neutral and Ground Conductors WARNING: Use ONLY approved ﬁttings and clamps to avoid damage to wires. Fig. 5 Fig. 6 a. Bring the phase, neutral and ground conductors into the enclosure through the bottom feed knockout. b. Connect the phase, neutral and ground conductors to the appropriate terminals and torque to spec in the terminations table (ﬁg. 5). Ground Terminal Step 6: Branch Circuit Breakers WARNING: Leviton® circuit breakers MUST BE used with a Leviton circuit breaker enclosure.