Instructions / Assembly

ManualsBrandsLeviton ManualsDimmersDecora Digital 450-Watt LED/CFL, 1000-Watt Incandescent Dimmer and Timer with Bluetooth Technology

Single Pole (One location) or 3-Way (Multi-location)

Universal Incandescent/Magnetic Low Voltage/Fluorescent or LED Dimmer

Cat. No. DDMX1-BL, 1000VA, 1000W, 450W LED/CFL (Lighted)

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

IMPORTANT: For 3-Way applications, note that one of the screw terminals

from the old switch being removed will usually be a different color (Black)

or labeled Common. Tag that wire with electrical tape and identify as the

common (Line or Load) in both the dimmer wall box and remote wall box.

For non-standard wiring applications, refer

to Wire Nut and Connector Size Chart

1 - #12 w/ 1 to 3 #14, #16 or #18

2 - #12 w/ 1 or 2 #16 or #18

1 - #14 w/ 1 to 4 #16 or #18

2 - #14 w/ 1 to 3 #16 or #18

WIRE CONNECTOR / # OF COND.

COMBINATION CHART

DI-000-DDMX1-02A

• Pull off pre-cut insulation from dimmer leads.

• Make sure that the ends of the wires from the wall box are straight

(cut if necessary).

• Remove insulation from each wire in the wall box as shown.

• For Single-Pole Application, go to Step 4a.

• For 3-Way Matching Remote (w/LEDs) Application, go to Step

4b.

Step 4b

TOOLS NEEDED TO INSTALL YOUR DIMMER

Slotted/Phillips Screwdriver Electrical Tape Pliers

Pencil Cutters Ruler

MULTI-DEVICE APPLICATION

In multi-dimmer installations, the reduction of the dimmer’s capacity may

be required. Refer to the chart for maximum load per dimmer.

NOTE: No derating is required for LED or CFL bulb applications.

If installing Dimmer in a single device application, proceed with the

INSTALLING YOUR DIMMER section. If installing Dimmer in a

multi-device application, proceed as follows:

INSTALLING DIMMER BY ITSELF

OR WITH OTHER DEVICES

Changing the color of your Dimmer:

Your device may include color options. To change color of the face

proceed as follows:

Insert top tabs and

press in bottom tabs

to attach

Push in sides at bottom

tabs and pull outward to

release

INSTALLING YOUR DIMMER

NOTE: Use check boxes when Steps are completed.

ONOFF

ONOFFONOFF

ONOFF

WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN

OFF POWER at circuit breaker or fuse and test that power

is off before wiring!

Step 1

Step 2

Identifying your wiring application (most common):

NOTE: If the wiring in your wall box does not resemble any

of these conﬁgurations, consult an electrician.

Single Pole

Line (Hot)

2. Neutral

3. Ground

4. Load

3-Way

Line or Load

(see important

instruction)

2. Neutral

3. Ground

4. First Traveler – note color

5. Second Traveler – note color

Cut

(if necessary)

5/8"

(1.6 cm)

Strip Gage

(measure bare

wire here)

Preparing and connecting wires:

Pull off pre-cut insulation from dimmer leads. Make sure that

the ends of the wires from the wall box are straight (cut if

necessary). Remove insulation from each wire in the wall box

as shown:

Step 3

Dimmer

Insulating

Label

Black

Load

Hot (Black)Black

Line

120 VAC,

60Hz

Neutral (White)

Red

Yellow/Red

White

Green

Ground

White

Red

Green

Black

Insulating label:

This wire is used in 3-way installations only.

For single pole installations, do not remove insulating label.

Yellow/Red

Single Pole Wiring Application:

Step 4a

MAXIMUM BULB WATTAGE

Low-voltage dimmers are rated in Volt-Amps (VA). The maximum bulb wattage

is determined by the efﬁciency of the transformer in the low-voltage lighting

system. Transformer efﬁciencies will vary from different manufacturers;

consider 80% efﬁcient as average. Use the chart to determine maximum bulb

wattage for typical transformer efﬁciency ratings.

MAXIMUM BULB WATTAGE

Mark 10

Powerline dimmers are rated in Volt-Amps (VA). The maximum bulb

wattage is determined by the efﬁciency of the Mark 10

Powerline ballast. The

following table shows the maximum number of ballasts that can be connected

to a single dimmer for different Mark 10

Powerline ballasts. Also note that the

table shows maximum ballasts for multi-gang installations.

Lutron Tu-Wire

To determine total ballast load, add the line current found on the ballast label

for all ballasts in the circuit. This will indicate the total load for the control.

Remove all

inner side

sections

Do not

remove

outer side

sections

Bend back and

forth to remove

side section

MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE

More than 2 Devices

700W

700VA

Two Devices

800W

800VA

Single

1000W

1000VA

Load

Incand

Mag LV

MAXIMUM BULB WATTAGE AT 75% EFFICIENCY

More than 2 Gang

560W

Rating

1000VA

Single

800W

Two Gang

640W

INTRODUCTION

The next generation of lighting control technology is here with the new

Decora

Digital Dimmer with Bluetooth

Technology. This innovative

device works using the Leviton Decora

Digital Dimmer & Timer app

that can be easily downloaded to smartphones or tablets and paired

to the Leviton Dimmer using Bluetooth

technology. Decora

Digital

Devices give users point-to-point local control to automate lighting,

bridging the gap between standard dimmers and whole-house

automation systems.

The Decora

Digital Dimmer is a powerful device – combining the best

of Leviton dimmer and timer functions with today’s mobile technology

for impressive results. The simple touch of a ﬁnger following the

intuitive on-screen guide makes it more convenient than ever to

manage lighting for home activities or to ensure a "lived-in" look while

away. Plus, the Decora

Digital Dimmer is Universal and compatible

with LED, CFL, Incandescent, Halogen or Mark 10

Powerline loads.

Use of the app allows greater ﬂexibility for accurate timer functionality

and makes pushing buttons for timed events a tedious chore of the

past.

The Leviton Decora

Digital Dimmer & Timer app can be easily

downloaded to mobile devices and is compatible with Android and iOS

smartphones or tablets. The app is easy to use with simple, intuitive

on-screen menu options to independently control dimmers and

switches throughout the home.

Decora

Digital Devices are ideal for living rooms, bedrooms, kitchens,

dining rooms, home ofﬁces, outdoor lighting or anywhere full control of

lighting is desired.

• Soft fade ON/OFF

• ON/OFF LED and Brightness level LED

• Three way communication

• Ease of installation – No new wiring

FEATURES

WIRING DIMMER:

Connect wires per WIRING DIAGRAM as follows:

WARNING: CONNECT A MAGNETIC LOW-VOLTAGE DIMMER ONLY

TO THE PRIMARY (HIGH-VOLTAGE) SIDE OF A MAGNETIC

LOW-VOLTAGE TRANSFORMER.

NOTE: The DDMX1 dimmer requires a neutral wire connection.

• Green or bare copper wire in wall box to Green dimmer lead.

• Line Hot wall box wire to Black dimmer lead.

• Load wall box wire to Red dimmer lead.

• Line Neutral wall box wire to White dimmer lead.

• Yellow/Red dimmer lead should have Red insulation label afﬁxed.

NOTE: If insulating label is not afﬁxed to Yellow/Red dimmer lead, use

electrical tape to cover.

• Proceed to Step 5.

Cat. No. DDMX1, 120V, For use with Advance Transformer

120V Mark 10

Powerline Electronic Ballasts

Max. # Ballasts/Dimmer for

Multi-gang

Advance

Mark 10

Powerline

Part No.

Lamp

Single

Gang

Two

Ganged

More than

2 Gang

REZ-2Q18-M2-LD

REZ-1T32

REZ-2Q26

REZ-1T32

REZ-1T42

REZ-1Q18-M2-BS

REZ-1Q18-M2-LD

REZ-2Q18-M2-BS

REZ-1T32

REZ-1T42-M2-BS

REZ-1T42-M2-LD

REZ-2Q26

REZ-2Q26-M2-BS

REZ-2Q26-M2-LD

REZ-1Q18-M2-BS

REZ-1Q18-M2-LD

REZ-2Q18-M2-BS

REZ-2Q18-M2-LD

REZ-1T42-M2-BS

REZ-1T42-M2-LD

REZ-2Q26-M2-BS

REZ-2Q26-M2-LD

REZ-1T42-M2-BS

REZ-1T42-M2-LD

REZ-2T42-M3-BS CFTR32W/GX24Q 13 10 8

CFTR32W/GX24Q 26 20 16

CFTR26W/GX24Q 17 13 11

CFTR26W/GX24Q 32 25 20

CFTR18W/GX24Q 23 18 15

CFTR18W/GX24Q 46 37 30

CFQ26W/G24Q 17 13 11

CFQ26W/G24Q 32 25 20

CFQ18W/G24Q 23 18 15

CFQ18W/G24Q 46 37 30

CFM42W/GX24Q 20 16 13

CFM32W/GX24Q 26 20 16

CFM26W/GX24Q 17 13 11

CFM26W/GX24Q 32 25 20

151823CFM18W/GX24Q

WARNINGS AND CAUTIONS:

• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!

•

TO AVOID FIRE, PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT install to control a receptacle, a motor- or a transformer-operated appliance.

• To be installed and/or used in accordance with electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

• Use ONLY with the appropriate Advance Transformer 120V Mark 10

Powerline or Lutron Tu-Wire

electronic ballasts for controlling the speciﬁc ﬂuorescent lamps in Fluorescent Mode.

• Use with magnetic low voltage transformers, incandescent, or 120V halogen ﬁxtures only. Use a Leviton electronic low voltage dimmer to control electronic (solid state) low voltage transformers.

• When retroﬁtting Mark 10

Powerline dimming ballasts into ﬁxtures that originally had Instant Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer

operation and prevent damage to the dimmer ballast. Refer to the instructions provided with the ballast.

• The Decora

DDMX1 dimmer is not compatible with standard 3-way or 4-way switches. It must be used with the

Decora

Digital DD00R-DL remote for multi-location dimming

WARNINGS AND CAUTIONS:

• Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.

• Dimmer may feel warm to the touch during normal operation.

• When magnetic low voltage circuits are operated at a dim level, with all lamps inoperative, excess current may ﬂow through the transformer. To avoid possible transformer failure due to

overcurrent, use a transformer that incorporates thermal protection or a fuse at the primary windings.

• Recommended minimum wall box depth is 2-3/4".

• Use this device WITH COPPER OR COPPER CLAD WIRE ONLY.

•

Use with compatible dimmable LED, CFL bulbs, incandescent or 120V halogen ﬁxtures only. For a list of compatible LED and CFL bulbs refer to www.leviton.com.

• When multiple bulbs are used with one dimmer DO NOT mix bulb types. All bulbs shall be either LED; CFL or incandescent. Using the same make/model of each bulb will enhance

dimmer performance.

WIRING MATCHING REMOTE (wall box with line hot

connection):

Connect wires per WIRING DIAGRAM as follows:

NOTE: The matching remote must be installed in a wall box with a

Line Hot connection and a Neutral connection. A Neutral wire to the

matching remote needs to be added as shown.

NOTE: Maximum wire length from dimmer to all installed remotes

cannot exceed 300 ft (90 m).

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot (common) wall box wire identiﬁed (tagged) when removing

old switch and First Traveler to Remote terminal marked "BK".

• Second Traveler wall box wire from dimmer to remote terminal screw

marked "YL/RD" (note wire color). This traveler from the remote

must go to Yellow/Red dimmer lead.

• Line Neutral wall box to remote terminal screw marked "WH".

WIRING DIMMER (wall box with load connection):

Connect wires per WIRING DIAGRAM as follows:

NOTE: The DDMX1 dimmer must be installed in a wall box that has a

Load connection and a Neutral connection.

• Green or bare copper wire in wall box to Green dimmer lead.

• Load wall box wire identiﬁed (tagged) when removing old switch to

Red dimmer lead.

• First Traveler Line Hot to Black dimmer lead.

• Remove Red insulating label from Yellow/Red dimmer lead.

• Second Traveler wall box wire (note color as above) to

Yellow/Red dimmer lead. This traveler from the dimmer must go to

the terminal screw on the remote marked "YL/RD".

• Line neutral wall box wire to White dimmer lead.

• Proceed to Step 5.

Hot (Black)

Neutral (White)

Dimmer

Matching Remote (w/LEDs)

YL/RD

Red

Yellow/

Red

WH BK

Black

White

Line

120V

AC, 60Hz

Green

Ground

Green

Ground

White

Load

3-Way Wiring with DD00R Matching Remote

(w/LEDs) Application:

Matching Remote Dimmer

Additional Neutral Wire

White

Red

Green

Black

Yellow/Red

Summary of content (2 pages)

PAGE 1
Single Pole (One location) or 3-Way (Multi-location) Universal Incandescent/Magnetic Low Voltage/Fluorescent or LED Dimmer Cat. No. DDMX1-BL, 1000VA, 1000W, 450W LED/CFL (Lighted) 120VAC, 60Hz INSTALLATION INSTRUCTIONS WARNINGS AND CAUTIONS: • TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring! • T O AVOID FIRE, PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT install to control a receptacle, a motor- or a transformer-operated appliance.
PAGE 2
Step 5 Testing your Dimmer prior to mounting in wall box: NOTE: If using in a dimmable fluorescent application see Advanced Programming Feature A-1 prior to testing the device. • Position all wires to provide room in outlet wall box for device. • Ensure that the word “TOP” is facing up on device strap. • Partially screw in mounting screws in wall box mounting holes. NOTE: Dress wires with a bend as shown in diagram in order to relieve stress when mounting device.