Installation Guide

ManualsBrandsLeviton ManualsDimmersDecora Digital 0-10-Volt Dimmer and Timer with Bluetooth Technology, White/Ivory/Light Almond

Single Pole (One location) or 3-Way (Multi-location)

0-10V LED/Fluorescent Digital Dimmer

Cat. No. DD710-BD, 120/277V, 950VA (120V), 1350VA (277V)

For use with ﬁxtures using 0-10V dimmable power supply/drivers, Advance Transformer Mark 7

OSRAM Sylvania QUICKTRONIC

, Helios

or equivalent dimmable ballasts

INSTALLATION INSTRUCTIONS

For non-standard wiring applications, refer

to Wire Connector and Conductor Size Chart

1 - #12 w/ 1 to 3 #14, #16 or #18

2 - #12 w/ 1 or 2 #16 or #18

1 - #14 w/ 1 to 4 #16 or #18

2 - #14 w/ 1 to 3 #16 or #18

WIRE CONNECTOR / # OF COND.

COMBINATION CHART

DI-000-DD710-02A

Step 4b

TOOLS NEEDED TO INSTALL YOUR DIMMER

Slotted/Phillips Screwdriver Electrical Tape Pliers

Pencil Cutters Ruler

NOTE: No derating is required in multi-device applications.

INSTALLING DIMMER BY ITSELF

OR WITH OTHER DEVICES

Changing the color of your Dimmer:

Your device may include color options. To change color of the face

proceed as follows:

Insert top tabs and

press in bottom tabs

to attach

Push in sides at bottom

tabs and pull outward to

release

• Pull off pre-cut insulation from dimmer leads.

• Make sure that the ends of the wires from the wall box are straight (cut

if necessary).

• Remove insulation from each wire in the wall box as shown.

• For Single-Pole Application, go to Step 4a.

• For 3-Way Matching Remote (w/LEDs) Application, go to Step 4b.

INSTALLING YOUR DIMMER

NOTE: Use check boxes when Steps are completed.

ONOFF

ONOFFONOFF

ONOFF

WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN

OFF POWER at circuit breaker or fuse and test that power

is off before wiring!

Step 1

Step 2

Identifying your wiring application (most common):

NOTE: If the wiring in your wall box does not resemble any

of these conﬁgurations, consult an electrician.

Single Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

5. Violet (

)

6. Gray (-)

3-Way

1. Line (Hot)

2. Neutral

3. Ground

4. Load

5. Violet (+)

6. Gray (-)

7. Yellow/Red

Cut

(if necessary)

5/8"

(1.6 cm)

Strip Gage

(measure bare

wire here)

Preparing and connecting wires:

Pull off pre-cut insulation from dimmer leads. Make sure that

the ends of the wires from the wall box are straight (cut if

necessary). Remove insulation from each wire in the wall box

as shown:

Step 3

Single Pole Wiring Application:

Step 4a

MAXIMUM BULB WATTAGE

0-10VDC ballasts are rated in Volt-Amps (VA). The maximum number of

ballast per dimmer is based on the load VA rating. The maximum bulb wattage

is determined by the efﬁciency of the ballast. Ballast efﬁciencies will vary from

different manufacturers; consider 80% efﬁcient as average. Use the chart to

determine maximum bulb wattage for typical ballast efﬁciency ratings.

INTRODUCTION

The next generation of lighting control technology is here with the new

Decora Digital dimmer with Bluetooth

technology. This innovative

device works using the Leviton Decora Digital Dimmer & Timer app that

can be easily downloaded to smartphones or tablets and paired to the

Leviton dimmer using Bluetooth

technology. Decora Digital devices

give users point-to-point local control to automate lighting, bridging the

gap between standard dimmers and whole-house automation systems.

The Decora Digital dimmer is a powerful device – combining the best of

Leviton dimmer and timer functions with today’s mobile technology for

impressive results. The simple touch of a ﬁnger following the intuitive

on-screen guide makes it more convenient than ever to manage

lighting for home activities or to ensure a "lived-in" look

while away.

Use of the app allows greater ﬂexibility for accurate timer functionality

and makes pushing buttons for timed events a tedious chore of

the past.

The Leviton Decora Digital Dimmer & Timer app can be easily

downloaded to mobile devices and is compatible with Android and iOS

smartphones or tablets. The app is easy to use with simple, intuitive

on-screen menu options to independently control dimmers and

switches throughout the home.

Decora Digital devices are ideal for living rooms, bedrooms, kitchens,

dining rooms, home ofﬁces, outdoor lighting or anywhere full control of

lighting is desired.

Compatibility:

Requires device with Bluetooth

4.0 (BT LE) or later and iOS 6.0 and

later. Compatible with iPhone, iPad, and iPod touch or Android 4.0 and

later.

• Soft fade ON/OFF

• ON/OFF LED and Brightness level LED

• Three way communication

• Ease of installation – No new wiring

FEATURES

WARNINGS AND CAUTIONS:

• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!

•

TO AVOID FIRE, PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT install to control a receptacle, a motor- or a transformer-operated appliance.

• To be installed and/or used in accordance with electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

• TO AVOID FIRE, SHOCK, OR DEATH; USE ONLY WITH appropriate LED 0-10V dimmable power supplies/drivers, Advance Transformer 120/277V Mark 7

0-10V ballasts or OSRAM

Sylvania QUICKTRONIC

or Helios

electronic ballasts.

• The Decora

DD710 dimmer is not compatible with standard 3-way or 4-way switches. It must be used with a Decora Digital remote for multi-location control, such as the DD00R-DL

WARNINGS AND CAUTIONS:

• Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.

• Dimmer may feel warm to the touch during normal operation.

• When retroﬁtting dimming ballasts into ﬁxtures that originally had Instant Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer operation and to

prevent damage to the dimming ballast. Refer to the instructions provided with the ballast.

• Recommended minimum wall box depth is 2-3/4".

• Use this device WITH COPPER OR COPPER CLAD WIRE ONLY.

3-Way Wiring with DD00R Matching Remote

(w/LEDs) Application:

Dimmer

Red

Violet

White

ellow/

Red

Gray

Black

Green

Connect wires per WIRING DIAGRAM as follows:

NOTE: The DD710 dimmer requires a neutral wire connection.

• Green or bare copper wall box wire to GREEN dimmer lead.

• Line Hot wall box wire to BLACK dimmer lead.

• Load wall box wire to RED dimmer lead.

• Remaining RED Dimmer lead should have a label afﬁxed.

• Line Neutral wall box wire to WHITE dimmer lead.

DO NOT REMOVE this label in a single pole application.

NOTE: If the insulating label is not afﬁxed to the second RED lead use

electrical tape or a wire connector to cover.

• Violet dimmer lead to (+) Violet connection on ballast.

• Gray dimmer lead to (-) Gray connection on ballast.

Proceed to Step 5.

Wiring Diagram 1

Insulating

Label

Green

Ground

Black White

Red

Hot (Black)

Neutral (white)

Line

120/277VAC

60Hz

Dimmer

Violet (+)

Gray (-)

ellow

To Lamps

Red

Blue

0-10 VDC

Ballast

Yellow/

Red

Matching Remote

Additional Neutral Wire

Dimmer

Red

Violet

White

Yellow/Red

Gray

Black

Green

Wiring Diagram 2

Green

Ground

Green

Ground

Black

White

Red

Hot (Black)

Neutral (White)

Line

120/277VAC

60Hz

DimmerMatching Remote

Violet (+)

Gray (-)

ellow

To Lamps

Red

Blue

0-10 VDC

Ballast

Yellow/Red

White

Black

MAXIMUM BULB WATTAGE AT 80% EFFICIENCY

Volts Rating Single Two Devices More than 2 Devices

120V 950VA 760VA 760VA 760VA

277V 1350VA 1080VA 1080VA 1080VA

WIRING MATCHING REMOTE (wall box with line hot

connection):

Connect wires per WIRING DIAGRAM as follows:

NOTE: The matching remote must be installed in a wall box with a Line

Hot connection and a Neutral connection. A Neutral wire to the matching

remote needs to be added as shown.

NOTE: Maximum wire length from dimmer to all installed remotes cannot

exceed 300 ft (90 m).

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot (common) wall box wire identiﬁed (tagged) when removing old

switch and First Traveler to Remote terminal marked "BK".

• Second Traveler wall box wire from dimmer to remote terminal screw

marked "YL/RD" (note wire color). This traveler from the remote must

go to Yellow/Red dimmer lead.

• Line Neutral wall box to remote terminal screw marked "WH".

WIRING DIMMER (wall box with load connection):

Connect wires per WIRING DIAGRAM as follows:

NOTE: The DD710 dimmer must be installed in a wall box that has a

Load connection and a Neutral connection.

• Green or bare copper wire in wall box to Green dimmer lead.

• Load wall box wire identiﬁed (tagged) when removing old switch to Red

dimmer lead.

• First Traveler Line Hot to Black dimmer lead.

• Remove Red insulating label from Yellow/Red dimmer lead.

• Second Traveler wall box wire (note color as above) to

Yellow/Red dimmer lead. This traveler from the dimmer must go to the

terminal screw on the remote marked "YL/RD".

• Line neutral wall box wire to White dimmer lead.

• Proceed to Step 5.

Summary of content (2 pages)

PAGE 1
Single Pole (One location) or 3-Way (Multi-location) 0-10V LED/Fluorescent Digital Dimmer Cat. No.
PAGE 2
Step 5 Testing your Dimmer prior to mounting in wall box: • Position all wires to provide room in outlet wall box for device. • Ensure that the word “TOP” is facing up on device strap. • Partially screw in mounting screws in wall box mounting holes. NOTE: Dress wires with a bend as shown in diagram in order to relieve stress when mounting device. ADVANCED PROGRAMMING FEATURES Definition of A Modes A-1) Maximum Brightness Level: Sets the maximum brightness level for energy savings.