LevelOne KVM-0115/KVM-0117 15 / 17-inch LCD KVM Rack Console User Manual Version 1.
SAFETY INSTRUCTIONS 1. Please read these safety instructions carefully. 2. Please keep this User Manual for later reference. 3. Please disconnect this equipment from AC outlet before cleaning. Don’t use liquid or sprayed detergent for cleaning. Use moisture sheet or clothe for cleaning. 4. For pluggable equipment, the socked-outlet shall be installed near the equipment and shall be easily accessible. 5. Please keep this equipment from humidity. 6. Lay this equipment on a reliable surface when install.
INDEX OF CONTENTS CHAPTER 1 INTRODUCTION .......................................................................................... 1 1.1 OVERVIEW ..................................................................................................................................... 1 1.2 PACKING LIST .......................................................................................................................... 1 CHAPTER 2 INSTALLATION ............................................................
CHAPTER 1 Introduction 1.1 Overview Congratulations on your purchase of LevelOne KVM-0115 / KVM-0117 15/17-inch rack mount console. The 15/17-inch large size TFT LCD color display and ultra-low-profile compact industrial keyboard / touchpad provide the user-friendliest and most reliable environment for server and network administrators.
CHAPTER 2 INSTALLATION 2.1 Install Console to Cabinet 2.1.1 Before Installation 1. Before installation, please check all peripherals according to the list. Make sure the whole unit was not damaged and lost during shipping process. If you encounter any problem, please contact your local dealer. 2. Before installation, make sure all peripherals and computer have been turned off. 3.
2.1.3 Installation Step 1. Loose (not release) four rear screws then adjust rear bracket to fit your cabinet. 2. Install front and rear bracket on cabinet. 3. Tight-up four rear screws. 4. Repeat step 1~3 for the other side. 5. Push console into left and right rails. (Be careful when take out console.) 6. Unlock and pull rail–lock switch (left and right at the same time) then push console to the end.
. Install three screws in rear of the console. (Both sides) 8. Finish installation as below. 2.1.4 Replace longer bracket Step (For rack depth 828~1000mm) 1. Release six screws. 2. Take rear bracket out. Original bracket 3. Input rear long bracket to rear of the rail then adjust rear bracket to fit your cabinet. Tight-up 2~3 screws upon the length you need. Rear long bracket 4. Repeat step 1~3 for the other side. 5. Repeat 2.1.3 step to install console to cabinet.
2.1.5 Unload Step 1. Make sure the console is lock. 2. Release three screws in rear of the console. (Both sides) 3. Unlock. 4. Pull console out until console lock. 5. Pull rail-release switch and pull console out.(Both sides. Be careful when pull out console.) rail-release switch 4. Push rail-lock switch on the rail and push rail back.
2.2 Connecting the console and Configuring the Display Settings Before connecting the rack mount console, make sure your computer has a video card. After you connect the console, please install the video card driver. The video driver is supplied by the video card manufacturer and may be found on the CDROM that came with your computer. If you need information on installing a video card or video driver, refer to the manual that came with your video card. 2.2.
change. This behavior is normal. You can readjust the image using the monitor on-screen controls. For more information on the monitor on-screen controls, refer to Chapter 3. For more information on configuring the display settings, refer to the manual that came with your video card. 2.3 Turning on the Console Make sure all cables and the power cord are connected properly. Be sure to tighten all connector screws. Using two hands, grasp the rear of the drawer, lift the tab and pull the panel up and forward.
CHAPTER 3 PANEL CONTROLS AND OSD FUNCTIONS Controls Description Soft power on/off button. Adjacent LED is lit when on. Auto ▲ Auto-synchronize and scale down display to any valid factory preset timings. Press to scroll the function you want to adjust. Press to scroll the function you want to adjust. When you’re not ▼ in OSD menu, it can be a hot key to switch between DVI and VGA video resource. Menu To access the main menu. This button also acts as the “Enter” button. 3.
3.4 Contrast 1. Press the “menu” button. 2. Use the “Down” and “Up” button to scroll, select “Contrast”. 3. Press the “menu” button to enter. 4. Use the “Down” and “Up” button to adjust the contrast of the display. 5. Press the “menu” button to enter. 3.5 Color 1. Press the “menu” button. 2. Use the “Down” and “Up” button to scroll, select “Color”. 3. Press the “menu” button to enter.
3.7 Language 1. Press the “menu” button. 2. Use the “Down” and “Up” button to scroll, select “Language”. 3. Press the “menu” button to enter. And you will see: English German French Italian Spanish 4. Use the “Down” and “Up” button to scroll. 5. Press the “menu” button to enter. 3.8 Recall 1. Press the “menu” button. 2. Use the “Down” and “Up” button to scroll, select “Recall”. 3. Press the “menu” button to enter, and you will see: Yes/ No 4.
Technical Specifications KVM-0115 Specifications Display Size 15" Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1024X768 (XGA) Pixel Pitch Supports 0.297mm x0.
USB Scroll Lock VGA Caps Lock DVI 12 Num Lock AC INPUT MOUSE 100~240 VAC 50~60 Hz KEYBOARD
KVM-0117 Specifications Display Size 17" Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1280X1024 (SXGA) Pixel Pitch Supports 0.264mm x0.264mm Viewing Angle (CR>10) Right-Left view 60~70 (Typ) Up-Down View 45~ 60(Typ) Contrast Ratio 450:1 Brightness White 250cd/m2 (Center 1 point Typ) Back Light Four Lamps for Back Light Supported Colors 16.2M Colors (6-bit with FRC) Response Time Rising Time 2ms, Decay Time 14ms Operating System Dos, Windows (3.
USB Scroll Lock VGA Caps Lock DVI 14 Num Lock AC INPUT MOUSE 100~240 VAC 50~60 Hz KEYBOARD
