IES-1081 8 FE + 2 GE SFP Managed Switch -40 to 75C, DIN-rail User Manual v1.
Preface This manual describes how to install and use the Hardened Managed Ethernet Switch. This switch introduced here is designed to deliver full scalability with SNMP/RMON web-based management functions by providing: To get the most out of this manual, you should have an understanding of Ethernet networking concepts.
Table of Contents PREFACE .................................................................................................................................................. 2 QUICK START GUIDE ..................................................................................................................................... 5 PHYSICAL DESCRIPTION ............................................................................................................................................
SWITCHING .......................................................................................................................................................... 91 TRUNKING ........................................................................................................................................................... 96 STP / RING ......................................................................................................................................................... 97 VLAN ...
Quick Start Guide This quick start guide describes how to install and use the Hardened Managed Ethernet Switch. This is the switch of choice for harsh environments constrained by space. Physical Description The Port Status LEDs and Power Inputs Front Panel Terminal Block PW1 PW2 Rear Panel + 12 48VDC Power Ground + 12 48VDC Power Ground Earth Ground Relay Output 1A @ 24VDC Relay Alarm warning signal disable for following: 1.
The relay output is normal open position when there is no power to the switch. Please do not connect any power source to this terminal to prevent shorting your power supply. There are three power inputs can be used.
Functional Description Complies with EN50121-4 environmental requirements for railway applications. Meets NEMA TS1/TS2 Environmental requirements such as temperature, shock, and vibration for traffic control equipment. Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment. Manageable via SNMP, Web-based, Telnet, and RS-232 console port. Supports IEEE802.3/802.3u/802.3ab/802.3z/802.3x.
Logon to Privileged Exec Mode (Enable Mode): screen. Logon to Configure Mode (Configure Terminal Mode): will show on the screen.
Web Configuration Login the switch: Specify the default IP address (192.168.1.10) of the switch in the web browser. A login window will be shown as below: Enter the factory default login ID: root. Enter the factory default password (no password). Then click on the Login button to log on to the switch.
Overview Hardened Managed Ethernet Switch Front View Package Contents When you unpack the product package, you shall find the items listed below. Please inspect the contents, and report any apparent damage or missing items immediately to your authorized reseller.
Product Highlights Basic Features Complies with EN50121-4 environmental requirements for railway applications. Meets NEMA TS1/TS2 Environmental requirements such as temperature, shock, and vibration for traffic control equipment. Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment. Manageable via SNMP, Web-based, Telnet, and RS-232 console port. Supports IEEE802.3/802.3u/802.3ab/802.3z/802.3x.
PORT-MIRRORING Port-mirroring QOS (IEEE802.1p Quality of Service) 4 priority queues INTERNETWORKING PROTOCOLS Bridging: IEEE802.1s Multiple Spanning Tree IEEE802.1w Rapid Spanning Tree IEEE802.1D Spanning Tree compatible IEEE802.
Front Panel Display POWER This LED comes on when the switch is properly connected to power and turned on. Port Status LEDs The LEDs are located on the front panel, displaying status for each respective port. Please refer to the following table for more details.
Physical Ports The Hardened Managed Ethernet Switch provides: Number of ports 10/100Base-TX 100Base-FX/BX Gigabit: 100Base SFP 10/100/1000Base-TX 1000Base-SX/LX/BX 1000Base SFP 8 0 0, 1, 2 6 2 0, 1, 2 4 2 0, 1, 2 4 4 0 CONNECTIVITY RJ-45 connectors on TX ports ST or SC connector on 100Base-FX fiber port SC connector on 100Base-BX fiber port Duplex LC connector on SFP 100Base-FX/BX fiber transceiver SC connector on 1000Base-SX/LX/BX fiber port Duplex LC connector on SFP 1000Base-SX/LX/BX fiber
Switch Management Web-based browser interface The switch also boasts a point-and-click browser-based interface that lets user access full switch configuration and functionality from a Netscape or Internet Explorer browser. Administration console via RS-232 serial port (CLI) The switch provides an onboard serial port, which allows the switch to be configured via a directly connected terminal. External SNMP-based application network management The switch can also be configured via SNMP.
Installation This chapter gives step-by-step instructions about how to install the switch: Selecting a Site for the Switch As with any electric device, you should place the switch where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements: -The ambient temperature should be between -40°C to 75℃ (-40℉ to 167℉). -The relative humidity should be less than 95 percent, non-condensing.
Connecting to Power Redundant DC Terminal Block Power Inputs or 12VDC DC Jack: 12VDC DC Jack Step 1: Connect the supplied AC to DC power adapter to the receptacle on the topside of the switch. Step 2: Connect the power cord to the AC to DC power adapter and attach the plug into a standard AC outlet with the appropriate AC voltage. Redundant DC Terminal Block Power Inputs There are two pairs of power inputs for use with redundant power sources.
Alarms for Power Failure Step 1: There are two pins on the terminal block used for power failure detection. It provides the normally closed output when the power source is active. Use this as a dry contact application to send a signal for power failure detection. Terminal Block PW1 PW2 + 12 48VDC Power Ground + 12 48VDC Power Ground Earth Ground Relay Output 1A @ 24VDC DC Jack Relay Alarm warning signal disable for following: 3.
Connecting to Your Network Cable Type & Length It is necessary to follow the cable specifications below when connecting the switch to your network. Use appropriate cables that meet your speed and cabling requirements. Cable Specifications Speed Connector Port Speed Half/Full Duplex Cable Max. Distance 10Base-T RJ-45 10/20 Mbps 2-pair UTP/STP Cat. 3, 4, 5 100 m 100Base-TX RJ-45 100/200 Mbps 2-pair UTP/STP Cat. 5 100 m 1000Base-T RJ-45 2000 Mbps 4-pair UTP/STP Cat.
Switch Management This chapter explains the methods that you can use to configure management access to the switch. It describes the types of management applications and the communication and management protocols that deliver data between your management device (workstation or personal computer) and the system. It also contains information about port connection options.
Administration Console (CLI) The administration console is an internal, character-oriented, Command Line Interface (CLI) for performing system administration such as displaying statistics or changing option settings. Using this method, you can view the administration console from a terminal, personal computer, Apple Macintosh, or workstation There are two ways to use this management method: direct access or modem access. The following sections describe these methods.
Web Management The switch provides a browser interface that lets you configure and manage the switch remotely. applications directly in your web browser by entering the IP address of the switch. You can then use your web browser to list and manage switch configuration parameters from one SNMP-Based Network Management You can use an external SNMP-based application to configure and manage the switch.
Management Architecture All of the management application modules use the same Messaging Application Programming Interface (MAPI). By unifying management methods with a single MAPI, configuration parameters set using one method (e.g. console port) are immediately displayed the other management methods (e.g. SNMP agent of web browser). The management architecture of the switch adheres to the IEEE open standard.
SNMP & RMON Management Thi Remote Monitoring (RMON) capabilities. Overview RMON is an abbreviation for the Remote Monitoring MIB (Management Information Base). RMON is a system defined by the Internet Engineering Task Force (IETF) document RFC 2819, which defines how networks can be monitored remotely.
WARM START COLD START LINK UP LINK DOWN AUTHENTICATION FAILURE RISING ALARM FALLING ALARM TOPOLOGY ALARM MIB-II defines a set of manageable objects in various layers of the TCP/IP protocol suites. MIB-II covers all manageable objects from layer 1 to layer 4, and, as a result, is the major SNMP MIB supported by all vendors in the networking industry. The switch supports a complete implementation of SNMP Agent and MIB-II.
Bridge Groups Supported The switch supports the following four groups of Bridge MIB (RFC 1493): - The dot1dBase Group a mandatory group that contains the objects applicable to all types of bridges. - The dot1dStp Group contains objects respect to the Spanning Tree Protocol. If a node does not implement the Spanning Tree Protocol, this group will not be implemented. This group is applicable to any transparent only, source route, or SRT bridge that implements the Spanning Tree Protocol.
Web-Based Browser Management The switch provides a web-based browser interface for configuring and managing the switch. This interface allows you to access the switch using a preferred web browser. This chapter describes how to configure the switch using its web-based browser interface. Logging on to the switch SWITCH IP ADDRESS In your web browser, specify the IP address of the switch. Default IP address is 192.168.1.10. LOGIN Enter the factory default login ID: root.
Understanding the Browser Interface The web browser interface provides groups of point-and-click buttons at the left field of the screen for configuring and managing the switch.
QOS Global Configuration, 802.1p Priority, DSCP SNMP SNMP General Setting, SNMP v1/v2c, SNMP v3 802.
System System Information View System information, VLAN ID, IP Address, and IP Subnet Mask of the Switch.
System Name/Password 1. System Name: System Name . Type a system name if it is blank, or replace the current system name with a new one. 2. Updating setting: C Updating setting button to update your settings. 3. Password: Password . Type a password. 4. Retype Password: Retype Password . Type the same password in Password again to verify it. 5. Updating setting: Click Updating setting button to update your settings. IP Address 1.
8. Submit: C Submit button when you finished DNS Server. Save Configuration 1. Load config from TFTP server: C TFTP Server text box and type the TFTP server IP address from where the file will be obtained. C FILE text box and type the name of the file that will be obtained. Load button to load the file from the TFTP server. 2. Backup config to TFTP server: C TFTP Server text box and type the TFTP server IP address to where the file will be back upped.
Firmware Upgrade 1. Filename: C Filename text box and type the name of the file that you intend to upgrade it to the switch. 2. TFTP server IP: C TFTP server IP text box and type the TFTP server IP address from where the file will be obtained. 3. Upgrade: C upgrade button to upgrade firmware to the switch. Please follow the message on the screen during the firmware upgrade process. Do not turn off the power or perform other functions during this period of time.
Please follow the message on the screen during the firmware upgrade process. Do not turn off the power or perform other functions during this period of time. Firmware has been upgraded successfully to the switch. Reboot the switch after completing the upgrade process.
Alarm Setting 1. Name: C Name drop-down menu to choose fe1~fe8 , ge1~ge2 , or Power1~Power3 Name drop-down list. 2. Trigger Enabled: C Trigger Enabled drop-down menu to choose YES or NO Trigger Enabled drop-down list to enable or disable Trigger. 3. Update Setting: C Update Setting button to update settings to the switch.
Reboot Reboot: Reboot button to restart the switch. Logout Logout: Logout button to logout of the switch.
Port Configuration 1. Admin Setting: C Admin Setting drop-down menu to choose Link down or Link up Admin Setting drop-down list to disable or enable Admin Setting for the port. 2. Speed: C Speed drop-down menu to change the line speed and duplex settings Speed drop-down list for the port. 3. Flow control: C Flow control drop-down menu to choose Disable or Enable Flow control drop-down list to disable or enable Flow control for the port. 4. Submit: C Submit button when you finished configurations.
Port Status View the Link Status, Speed, Duplex, and Flow control status for all ports. Rate Control 1. Ingress: C Ingress text box and type a new Rate to change the Ingress Rate Control for the port. Rate Values: 64kbps, 128kbps, 192kbps, , 1792kbps. 2Mbps, 3Mbps, 4Mbps, , 100Mbps. 104Mbps, 112Mbps, 120Mbps, , 1000Mbps. : M = 1024k. 2. Egress: C Egress text box and type a new Rate to change the Egress Rate Control for the port. Rate Values: 64kbps, 128kbps, 192kbps, , 1792kbps.
RMON Statistics Click Port 1 ~ Port 10 to view corresponding RMON Statistics. Per port vlan activities Click Port 1 ~ Port 10 to view corresponding vlan activities.
Switching Bridging 1. Aging Time (seconds): Click the text box and type a decimal number as Bridging Aging Time in seconds. 2. Update setting: C update setting button when you finished Aging Time settings. 3. Threshold level (0-100): Click Level for the port. Need to choose Broadcast and/or DFL-Multicast from Storm-control enabled type for the port. DLF (Destination Lookup Failure). 4. Storm-control enabled type: Choose Broadcast and/or DLF-Multicast from Storm-control enabled type for the port. 5.
Static MAC Entry Static-MAC-Entry Forward: 1. Add MAC address: Click in Add MAC address locked forwarding MAC address for the port. 2. VLAN ID: C VLAN ID drop-down menu and choose a VLAN ID VLAN ID drop-down list. 3. Delete MAC address: C Delete MAC address drop-down menu and choose a locked forwarding MAC address Delete MAC address drop-down list to be deleted from the port. 4. Submit: C Submit button when you finished Static-MAC-Entry Forward settings. Static-MAC-Entry Discard: 1.
Port Mirroring 1. Mirror From: Choose Mirror From port from Port 1 ~ Port 10. 2. Mirror To: Click Mirror To drop-down menu to Choose Mirror To port (Port 1 ~ Port 10) from Mirror To drop-down list. 3. Mirror Mode: C Mirror Mode drop-down menu to Choose Tx/Rx , Tx , or Rx from Mirror Mode drop-down list. 4. Submit: C Submit button when you finished Port Mirroring settings.
Trunking Port Trunking Static Channel Group: 1. Trunk 1: Click Port 1 ~ Port 8 to assign ports to Trunk 1. (Maximum 4 ports in Trunk 1.) GE Trunking: 1. Trunk 3: Click Static or Disable for Trunk 3. 2. Submit: C Submit button when you finished Port Trunking settings.
STP / Ring Global Configuration 1. Spanning Tree Protocol: C Spanning Tree Protocol drop-down menu to Choose Enable or Disable from Spanning Tree Protocol drop-down list to enable or disable Spanning Tree Protocol. 2. Bridge Priority (0..61440): C Bridge Priority between 0 and 61440. 3. Hello Time (sec) (1..9): C Hello Time between 1 and 9. 4. Max Age (sec) (6..28): C Max Age 6 and 28. 5. Forward Delay (sec) (4..30): C Forward Delay number between 4 and 30. 6.
RSTP Port Setting 1. STP Version: C STP Version drop-down menu to choose RSTP from STP Version drop-down list. 2. Port: C Port drop-down menu to Choose Port 1 ~ Port 10 from Port drop-down list. 3. Priority(Granularity 16): C Priority enter a value between 0 and 240 to set the priority for the port. A higher priority will designate the port to forward packets first. A lower number denotes a higher priority. This entry must be divisible by 16. The default priority setting is 128. 4. Admin.
MSTP Properties 1. STP Version: C STP Version drop-down menu to choose MSTP from STP Version drop-down list. 2. Region Name: C Region Name to create an MST region and specify a name to it. MST bridges of a region form different spanning trees for different VLANs. By default, each MST bridge starts with the region name as its bridge address. This means each MST bridge is a region by itself, unless specifically added to one. 3.
max hops for a BPDU prevents the messages from looping indefinitely in the network. When a bridge receives a MST BPDU that has exceeded the allowed max-hops, it discards the BPDU. 5. Update setting: C Update setting button when you finished MSTP Properties setting. MSTP Instance Setting VLAN Instance Configuration 1. VLAN Instance Configuration: C VLAN Instance Configuration button. The VLAN Instance Configuration window appears. 2.
Configuration. Included VLANs 1. Instance ID: C Instance ID drop-down menu to choose instance ID from Instance ID drop-down list. 2. Included VLAN: C Included VLAN drop-down menu to choose VLAN from Included VLAN drop-down list. Instance Setting 1. Bridge Priority (0..61440): C Bridge Priority to set the bridge priority for an MST instance to the value specified. The lower the priority of the bridge, the better the chances are the bridge becoming a root bridge or a designated bridge for the LAN. 2.
MSTP Port Setting Port Instance Configuration 1. Instance ID: C Instance ID drop-down menu to choose instance ID from Instance ID drop-down list. 2. Click Port 1 ~ Port 10 to assign ports to the corresponding instance ID. 3. Update setting: C Update setting button when you finished Port Instance Configuration. Instance ID 1. Instance ID: C Instance ID drop-down menu to choose instance ID from Instance ID drop-down list. MSTP Port Configuration 1.
Ring Setting Ring state 1. C Ring state drop-down menu from Ring state drop-down list to choose Enable or Disable to enable or disable Ring state. 2. Update setting: C Update setting button when you finished Ring state setting. Set ring port 1. Ring port 1: C Ring port 1 drop-down menu to choose Ring port 1 from Ring port 1 drop-down list. 2. Ring port 2: C Ring port 2 drop-down menu to choose Ring port 2 from Ring port 2 drop-down list. 3.
VLAN VLAN Mode Setting 1. VLAN Mode Setting: C VLAN Mode Setting drop-down menu to choose Tag-based VLAN or Port-based VLAN from VLAN Mode Setting drop-down list. 2. Update Setting: C Update Setting button when you finished VLAN Mode Setting.
802.1Q VLAN setting Add VLAN: 1. VLAN setting: Click VLAN setting . The VLAN Setting window appears. 2. Add VLAN: C Add VLAN button to create a new VLAN from VLAN Setting window. 3. VLAN ID(2-4094): VLAN ID textbox and specify a new VLAN ID number from 2 ~ 4094. 4. VLAN Name: VLAN Name textbox and type a name for this newly created VLAN. Add port to or delete port from VLAN: 1. VLAN Member: Choose the port to be added to or deleted from the VLAN. 2.
Delete VLAN: 1. VLAN setting: Click VLAN setting . The VLAN Setting window appears. 2. Delete VLAN: C Delete VLAN button. 3. Select a VLAN ID: C Select a VLAN ID drop-down menu from Select a VLAN ID drop-down list to choose the VLAN to be deleted. 4. Submit: C Submit button when you finished VLAN setting. 802.1Q Port Setting 1. VLAN Port Setting: Click VLAN Port Setting . The VLAN Port Setting window appears. 2.
Port Based VLAN 1. VLAN: Choose the port to be added to or deleted from the VLAN. 2. Select all: C select all button to choose Port 1 ~ Port 10 all to be added to the VLAN. 3. Delete all: C delete all button to choose Port 1 ~ Port 10 all to be deleted from the VLAN. 4. Submit: C Submit button when you finished Port Based VLAN setting.
QoS Global Configuration 1. QoS: C QoS drop-down menu from QoS drop-down list to choose Enable or Disable to enable or disable QoS. 2. Trust: Enable or disable the switch port to trust the CoS (Class of Service) labels of all traffic received on that port. Enable or disable a routed port to trust the DSCP (Differentiated Service Code Point) labels of all traffic received on that port. 3. Policy: Choose Strict Priority(Queue3) + WRR(Queue0-2) or WRR(Queue0-3) .
802.1p Priority 1. Priority: C Priority drop-down menu from Priority drop-down list to choose 0 ~ 3 for VLAN Priority 0 ~ 7. 2. Submit: C Submit button when you finished 802.1p priority. DSCP 1. Priority: C Priority drop-down menu from Priority drop-down list to choose 0 ~ 3 for DSCP Priority 0 ~ 63. 2. Submit: C Submit button when you finished DSCP.
SNMP SNMP General Setting 1. SNMP Status: C SNMP Status drop-down menu from SNMP Status drop-down list to choose Enable or Disable to enable or disable SNMP. 2. Description: Click in Description textbox and specify a new description for SNMP. 3. Location: Location textbox and specify a new location for SNMP. 4. Contact: Contact textbox and specify a new contact for SNMP. 5. Trap Community Name: For each Trap Community Name , Trap Community Name textbox and specify a trap community name. 6.
SNMP v1/v2c 1. Get Community Name: Get Community Name textbox and specify a get community name. 2. Set Community Name: Cl Set Community Name textbox and specify a set community name. 3. Update Setting: C Update Setting button when you finished SNMP V1/V2c Setting.
SNMP v3 Add User: 1. Add User: C Add User button. The SNMP V3 Setting window appears. 2. SNMP Version: C SNMP Version drop-down menu from SNMP Version drop-down list to choose SNMPv3 No-Auth , SNMPv3 Auth-MD5 , SNMPv3 Auth-SHA , SNMPv3 Priv Auth-MD5 , or SNMPv3 Priv Auth-SHA . SNMPv3 No-Auth: Add a user using SNMP v3 without authentication. SNMPv3 Auth-MD5: Add a user using SNMP v3 with authentication. Auth. Password textbox and specify an authentication password.
Delete User: 1. Delete User: C Delete User button. The Select User Name window appears. 2. Select User Name: C Select User Name drop-down menu from Select User Name drop-down list to choose the user to be deleted from using SNMP v3. 3. Submit: C Submit button when you finished user deletion.
802.1x Radius Configuration 1. Radius Status: C Radius Status drop-down menu from Radius Status drop-down list to choose Enable or Disable to globally enable or disable authentication. 2. Update Setting: C Update Setting button when you finished Radius Status Setting. Add Radius: 1. Add Radius: C Add Radius button. The Radius Server Setting window appears. 2. Radius Server IP: Radius Server IP textbox and specify the IP address of the remote radius server host. 3.
This key must match the encryption used on the radius daemon. All leading spaces are ignored, but spaces within and at the end of the key are used. If spaces are used in the key, do not enclose the key in quotation marks unless the quotation marks themselves are part of the key. 5. Timeout <1-1000>: Timeout textbox and specify the time interval (in seconds) that the Switch waits for the radius server to reply before retransmitting. Enter a value in the range 1 to 1000. 6.
Port Authentication 1. Interface: C Interface drop-down menu from Interface drop-down list to choose the port to be set port-based authentication. 2. Authentication State: C Authentication State drop-down menu from Authentication State drop-down list to choose Enable or Disable to enable or disable authentication state. 3. Port Control: C Port Control drop-down menu from Port Control drop-down list to choose Auto , Force Authorized , or Force Unauthorized to force a port state.
Other Protocols GVRP GVRP Global Setting: 1. GVRP: C GVRP drop-down menu from GVRP drop-down list to choose Enable or Disable to enable or disable GVRP (GARP VLAN Registration Protocol). 2. Dynamic VLAN creation: C Dynamic VLAN creation drop-down menu from Dynamic VLAN creation drop-down list to choose Enable or Disable to enable or disable Dynamic VLAN creation. GARP (Generic Attribute Registration Protocol) provides IEEE802.1Q compliant VLAN pruning and dynamic VLAN creation on IEEE802.1Q trunk ports. 3.
3. GVRP registration: C GVRP registration drop-down menu from GVRP registration drop-down list to choose Enable or Disable to enable or disable GVRP registration to the port. Configuring an IEEE802.1Q trunk port in registration mode allows dynamic creation (if dynamic VLAN creation is enabled), registration, and deregistration of VLANs on the trunk port. 4. Update Setting: C Update Setting button when you finished Per port setting. IGMP Snooping 1. 2. 3. 4. 5. - -down list to for the switch.
an entry between 1 and 124 (seconds). Default = 10. IGMP passive snooping: 1. Report suppression: report suppression report suppression Enable Disable for the switch. Use this command to enable report suppression for IGMP version 1 and version 2. Report suppression does not apply to IGMP version 3, and is turned off by default for IGMP version 1 and IGMP version 2 reports. The switch uses IGMP report suppression to forward only one IGMP report per multicast router query to multicast devices.
Daylight Saving Setting: 1. Daylight Saving Mode: Click "Daylight Saving Mode" drop-down menu from "Daylight Saving Mode" drop-down list to choose "Disable", "Weekday", or "Date" to choose disable, weekday, or date daylight saving for the Switch. 2. Time Set Offset (1-1440 min): Click in the "Time Set Offset" textbox and specify the offset time of daylight saving. For example enter 60 for one hour offset. 3.
Command Line Console Management The switch provides a command line console interface for configuration purposes. The switch can be configured either locally through its RS-232 port or remotely via a Telnet session. For the later, you must specify an IP address for the switch first. This chapter describes how to configure the switch using its console by Commend Line.
(or View Mode). switch_a login: root Basic commands Exec Mode (or View Mode) is the base mode from where users can perform basic commands like: clear, debug, disable, enable, exit, help, logout, no, quit, show, terminal The CLI contains a text-based help facility. Access this help by typing in the full or partial command string then or parameters along with a short description. At the switch_a> prompt just press to list the above basic commands.
Login timed out The login session to Exec Mode (or View Mode) has timed out due to an extended period of inactivity (60 seconds) to indicate authentication attempt timed out. And the switch_a login: prompt will show on the screen. Logon back to Exec Mode (View Mode) At the switch_a login: Mode (or View Mode).
Exit from Exec Mode (View Mode) At the switch_a> View Mode). switch_a>exit Privileged Exec Mode (Enable Mode) Logon to Privileged Exec Mode (Enable Mode) At the switch_a> Exec Mode (or Enable Mode). And the switch_a# prompt will show on the screen.
Commands Privileged Exec Mode (or Enable Mode) allows users to run commands as following. At the switch_a# prompt just press to list the commands.
question to display the command keywords or parameters along with a short description. switch_a#show ? Login timed out The login session to Privileged Exec Mode (or Enable Mode) has timed out due to an extended period of inactivity (60 seconds) to indicate authentication attempt timed out. And the switch_a login: prompt will show on the screen. Logon back to Exec Mode (View Mode) At the switch_a login: Mode (or View Mode).
Exit from Privileged Exec Mode (or Enable Mode) At the switch_a# Mode (or Enable Mode). switch_a#exit Configure Mode (Configure Terminal Mode) Logon to Configure Mode (Configure Terminal Mode) At the switch_a# Configure Mode (or Configure Terminal Mode). And the switch_a(config)# prompt will show on the screen.
Commands Configure Mode (or Configure Terminal Mode) serves as a gateway into the modes as following. At the switch_a(config)# prompt just press to list the commands.
At the switch_a(config)# prompt just type in the full or partial command string then to display the command keywords or parameters along with a short description. switch_a(config)#show ? Login timed out The login session to Configure Mode (or Configure Terminal Mode) has timed out due to an extended period of inactivity (60 seconds) to indicate authentication attempt timed out. And the switch_a login: prompt will show on the screen.
System System Information, System Name/Password, IP Address, Save Configuration, Firmware Upgrade, Alarm Setting, Reboot, Logout System Name/Password System Name: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use hostname command to set or change the network server name. Use the no hostname command to disable this function. 3.
switch_a(config)# 2. Usage: Use enable password command to modify or create a password to be used when entering the Enable mode. 3. Command Syntax: enable password PASSWORD PASSWORD specifies the new password of the system. 4.
IP Address IP Address/IP Subnet Mask: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. vlan1.1 means vlan 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface vlan1.1 switch_a(config-if )# 2. Usage: Use ip address command to set the IP address of an interface. Use the no ip address command to remove the IP address from an interface. 3.
The following example sets the default gateway 192.168.1.254 to switch: switch_a(config)#ip default-gateway 192.168.1.254 switch_a(config)# DNS Server: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use ip dns command to set the IP address of the DNS server. Use the no ip dns command to remove the IP address of the DNS server. 3. Command Syntax: ip dns IP-ADDRESS no ip dns IP-ADDRESS A.B.C.
switch_a# Load config to TFTP server: 1. Command Mode: Privileged Exec mode Logon to Privileged Exec Mode (Enable Mode). The switch_a# prompt will show on the screen. switch_a# 2. Usage: Use write config-file command to backup configuration file to tftp server. 3. Command Syntax: write config-file IP-ADDRESS IP-ADDRESS specifies the IP address of tftp server. 4. Example: The following example backups configuration file to tftp server (IP address: 192.168.1.100): switch_a#write config-file 192.168.1.
1. Command Mode: Privileged Exec mode Logon to Privileged Exec Mode (Enable Mode). The switch_a# prompt will show on the screen. switch_a# 2. Usage: Use restore default command to restore default setting of the switch. 3. Command Syntax: restore default 4. Example: The following example restores default setting of the switch: switch_a#restore default switch_a# Auto Save: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen.
2. Usage: Use this command to set the interval when the configuration would be automatically saved. The range of interval value is from 5 to 65535. And the default value is 30 seconds. 3. Command Syntax: service auto-config interval WORD WORD specifies the interval value. 4. Example: The following example sets the interval WORD (10) when the configuration would be automatically saved to switch: switch_a(config)#service auto-config interval 10 switch_a(config)# Firmware Upgrade 1.
# after completing the upgrade process. eload reboot the switch Alarm Setting Alarm-trigger if: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to enable or disable alarm trigger on interface. 3. Command Syntax: (no) alarm-trigger if INTERFACE INTERFACE specifies the interface.
4. Example: The following example enables alarm trigger on interface fe1 to switch: switch_a(config)#alarm-trigger if fe1 switch_a(config)# Alarm-trigger power: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to enable or disable alarm trigger of power source. 3. Command Syntax: (no) alarm-trigger power POWER POWER specifies the power source. 4.
Logout 1. Command Mode: Exec mode or Privileged Exec mode Logon to Exec Mode (View Mode) or Privileged Exec Mode (Enable Mode). The switch_a> or switch_a# prompt will show on the screen. switch_a> switch_a# 2. Usage: Use logout command to exit from the Exec mode or Privileged Exec mode. 3. Command Syntax: logout 4. Example: The following example specifies to exit from the Exec mode or Privileged Exec mode.
switch_a(config)#interface fe1 switch_a(config-if )#shutdown switch_a(config-if )# Duplex: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if )# 2. Usage: Use duplex command to specify the duplex mode to be used for each interface. Use the no duplex to disable this function. 3.
no flowcontrol 4. Example: The following example shows the use of flowcontrol on to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if )#flowcontrol on switch_a(config-if )# Port Status 1. Command Mode: Exec mode or Privileged Exec mode Logon to Exec Mode (View Mode) or Privileged Exec Mode (Enable Mode). The switch_a> or switch_a# prompt will show on the screen. switch_a> switch_a# 2. Usage: Use the show interface command to display interface configuration and status. 3.
3. Command Syntax: (no) rate-control ingress/egress VALUE VALUE <1-10000000000 bits> (usable units: k, m, g) <1-999>k|m for 1 to 999 kilo bits or mega bits. 1g for 1 giga bits. 4. Example: The following example shows the use of rate-control ingress VALUE (10 mega bits) to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if )#rate-control ingress 10m switch_a(config-if )# RMON Statistics 1.
2. Usage: Use show vlan command to display information about a particular VLAN by specifying the VLAN ID. 3. Command Syntax: show vlan <2-4094> <2-4094> VLAN ID. 4.
Switching Bridging, Static MAC Entry, Port Mirroring Bridging Aging Time (seconds): 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to specify an ageing-out time for a learned MAC address. The learned MAC address will persist till this specified time. 3.
4. Example: The following example shows setting storm-control level LEVEL (30) to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if )#storm-control level 30 switch_a(config-if )# Broadcast: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if )# 2.
Use no storm-control multicast command to disable multicast traffic. 3. Command Syntax: storm-control multicast enable no storm-control multicast 4. Example: The following example shows setting storm-control multicast enable to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if )#storm-control multicast enable switch_a(config-if )# DLF: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1.
switch_a(config)# 2. Usage: Use this command to statically configure a bridge entry to forward matching frames. 3. Command Syntax: bridge GROUP address MAC forward IFNAME VLANID no bridge GROUP address MAC forward IFNAME VLANID GROUP <1-1> Bridge-group ID used for bridging. MAC the Media Access Control (MAC) address in the HHHH.HHHH.HHHH format. IFNAME the interface on which the frame comes in. VLANID The VID of the VLAN that will be enabled or disabled on the bridge <2-4094>. 4.
Port Mirroring 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if )# 2. Usage: Use this command to define a mirror source port and its direction. Use the no parameter with this command to disable port mirroring by the destination port on the specified source port. 3.
Trunking Port Trunking Port Trunking 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if )# 2. Usage: Use static-channel-group command to create a static aggregator, or add a member port to an already-existing static aggregator. Use the no static-channel-group command to detach the port from the static aggregator. 3.
STP / Ring Global Configuration, RSTP Port Setting, MSTP Properties, MSTP Instance Setting, MSTP Port Setting, Ring Setting Global Configuration STP Version: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to choose the Spanning Tree protocol, Rapid Spanning Tree protocol, or Multiple Spanning Tree protocol on a bridge. 3.
BRIDGE-FORWARD Puts all ports of the specified bridge into the forwarding state. 4. Example: The following example enables or disables the multiple-spanning-tree on bridge GROUP (1): switch_a(config)#bridge 1 multiple-spanning-tree enable switch_a(config)#no bridge 1 multiple-spanning-tree enable bridge-forward switch_a(config)# Rapid Spanning Tree Protocol: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen.
BRIDGE-FORWARD Puts all ports of the specified bridge into the forwarding state. 8. Example: The following example enables or disables the spanning-tree on bridge GROUP (1): switch_a(config)#bridge 1 spanning-tree enable switch_a(config)#no bridge 1 spanning-tree enable bridge-forward switch_a(config)# Bridge Priority (0..61440): 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2.
GROUP <1-1> The ID of the bridge group to which this hello time is assigned. HELLOTIME <1-9> The hello BPDU interval in seconds. 4. Example: The following example sets the hello-time HELLOTIME (9) of bridge GROUP (1): switch_a(config)#bridge 1 hello-time 9 switch_a(config)# Max Age (sec) (6..28): 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2.
GROUP <1-1> The ID of the bridge group to which this delay time is assigned. FORWARD_DELAY <4-30> the forwarding time delay in seconds. 4. Example: The following example sets the forward-time FORWARD_DELAY (30) of bridge GROUP (1): switch_a(config)#bridge 1 forward-time 30 switch_a(config)# RSTP Port Setting Priority(Granularity 16): 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1.
2. Usage: Use this command to set the cost of a path associated with a bridge-group. Use the no parameter with this command to restore the default cost of a path associated with a bridge-group. 3. Command Syntax: bridge GROUP path-cost PATHCOST no bridge GROUP path-cost GROUP <1-1> the ID of the bridge group. PATHCOST <1-200000000> The cost to be assigned to the group. 4.
Autoedge: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if )# 2. Usage: Use spanning-tree autoedge command to assist in automatic identification of the edge port. Use the no spanning-tree autoedge command to disable this feature. 3. Command Syntax: (no) spanning-tree autoedge 4.
switch_a(config)#interface fe1 switch_a(config-if )#spanning-tree edgeport switch_a(config-if )# MSTP Properties Region Name: 1. Command Mode: MST Configuration mode Logon to Configure Mode (Configure Terminal Mode). Then logon to MST Configuration mode. The switch_a(config-mst)# prompt will show on the screen. switch_a(config)#spanning-tree mst configuration switch_a(config-mst)# 2. Usage: Use this command to create an MST region and specify a name to it.
3. Command Syntax: bridge GROUP revision REVISION_NUM GROUP <1-1> Specify the bridge-group ID. REVISION_NUM <0-255> Revision number. 4. Example: The following example specifies a revision number (25) of MST configuration in bridge GROUP (1): switch_a(config)#spanning-tree mst configuration switch_a(config-mst)#bridge 1 revision 25 switch_a(config-mst)# Max Hops: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen.
switch_a(config)#spanning-tree mst configuration switch_a(config-mst)# 2. Usage: Use this command to simultaneously add multiple VLANs for the corresponding instance of a bridge. This command can be used only after the VLANs are defined. Use the no parameter with this command to simultaneously remove multiple VLANs for the corresponding instance of a bridge. 3.
(1): switch_a(config)#bridge 1 instance 3 priority 0 switch_a(config)# MSTP Port Setting Bridge-Group Instance: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if )# 2. Usage: Use this command to assign a Multiple Spanning Tree instance to a port. Use the no parameter with this command to remove the instance. 3.
for a particular instance on a LAN, or which port should be the root port for an instance. A lower value implies a better priority. In the case of the same priority, the interface index will serve as the tiebreaker, with the lower-numbered interface being preferred over others. The permitted range is 0-240. The priority values can only be set in increments of 16. 3. Command Syntax: bridge GROUP instance INSTANCE_ID priority PRIORITY GROUP <1-1> Specify the bridge-group ID.
Ring Setting Ring state: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to enable Ring state. Use the no parameter with this command to disable Ring state. 3. Command Syntax: bridge GROUP protocol ring no bridge GROUP ring enable BRIDGE-FORWARD GROUP <1-1> Specify the bridge-group ID. BRIDGE-FORWARD Puts all ports of the specified bridge into the forwarding state. 4.
VLAN VLAN Mode Setting, 802.1Q VLAN Setting, 802.1Q Port Setting, Port Based VLAN 802.1Q VLAN Setting VLAN Database: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use vlan database command to enter the VLAN configuration mode. 3. Command Syntax: vlan database 4.
disable Sets VLAN into a disable state. 4. Example: The following example enables the vlan VLANID (2) and name VLAN_NAME (vlan2) of bridge GROUP (1): switch_a(config-vlan)#vlan 2 bridge 1 name vlan2 state enable switch_a(config-vlan)# 802.1Q Port Setting Switchport mode access: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen.
2. Usage: Use switchport mode hybrid command to set the switching characteristics of the Layer-2 interface as hybrid, and classify both tagged and untagged frames. Use the no switchport hybrid command to reset the mode of the Layer-2 interface to access (default). 3. Command Syntax: switchport mode hybrid switchport mode hybrid acceptable-frame-type all/vlan-tagged no switchport hybrid all Set all frames can be received. vlan-tagged Set vlan-tagged frames can only be received. 4.
Switchport hybrid allowed vlan: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if )# 2. Usage: Use this command to set the switching characteristics of the Layer-2 interface to hybrid. Both tagged and untagged frames will be classified over hybrid interfaces. Use the no parameter to turn off allowed hybrid switching. 3.
The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if )# 2. Usage: Use this command to set the switching characteristics of the Layer-2 interface to trunk. The all parameter indicates parameter indicates that no VLAN ID is configured on this port. The add and remove Use the no parameter to remove all VLAN IDs configured on this port. 3.
2. Usage: Use this command to set or remove the default VLAN for the interface. 3. Command Syntax: switchport portbase add｜remove vlan VLANID VLANID The ID of the VLAN will be added to or removed from the Layer-2 interface. 4.
QoS Global Configuration, 802.1p Priority, DSCP Global Configuration QoS: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use mls qos enable command to globally enable QoS. Use the no mls qos command to globally disable QoS. 3. Command Syntax: mls qos enable (no) mls qos 4.
Strict Priority: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use priority-queue out command to enable the egress expedite queue. Use the no priority-queue out command to disable the egress expedite queue. 3. Command Syntax: (no) priority-queue out 4.
Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use wrr-queue cos-map command to specify CoS values for a queue. 3. Command Syntax: wrr-queue cos-map QUEUE_ID COS_VALUE QUEUE_ID Queue ID. Range is 0-3. COS_VALUE CoS values. Up to 8 values (separated by spaces). Range is 0-7. 4.
SNMP SNMP General Setting, SNMP v1/v2c, SNMP v3 SNMP General Setting SNMP Status: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use snmp-server enable command to enable and no snmp-server enable command to disable SNMP to the switch. 3. Command Syntax: (no) snmp-server enable 4.
Location: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use snmp-server location command to specify and no snmp-server location command to remove location for SNMP. 3. Command Syntax: snmp-server location LOCATION no snmp-server location LOCATION The location for SNMP. 4.
Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to specify trap community name for SNMP. Use the no parameter with this command to remove trap community name for SNMP. 3. Command Syntax: snmp-server trap-community <1-5> NAME no snmp-server trap-community <1-5> <1-5> The trap community 1-5. NAME The trap community name for SNMP. 4.
The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use snmp-server trap-type enable linkDown command to enable link down trap for SNMP. Use the no snmp-server trap-type enable linkDown command to disable link down trap for SNMP. 3. Command Syntax: (no) snmp-server trap-type enable linkDown 4. Example: The following example enables link down trap for SNMP: switch_a(config)#snmp-server trap-type enable linkDown switch_a(config)# Link Up Trap: 1.
2. Usage: Use snmp-server community get command to specify and no snmp-server community get command to remove get community name for SNMP. 3. Command Syntax: snmp-server community get NAME no snmp-server community get NAME The get community name for SNMP. 4. Example: The following example specifies get community name (name) for SNMP: switch_a(config)#snmp-server community get name switch_a(config)# Set Community Name: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode).
Add a user using snmp v3 with read-only or read-write access mode and without authentication. Use the no form of the command to delete this user. 3. Command Syntax: (no) snmp-server v3-user USERNAME (ro｜rw) noauth USERNAME Specify a user name. ro read-only access mode rw read-write access mode 4.
The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Add a user using snmp v3 with read-only or read-write access mode, MD5 or SHA authentication, and privacy. Use the no form of the command to delete this user. 3. Command Syntax: (no) snmp-server v3-user USERNAME (ro｜rw) priv auth (md5｜sha) AUTH_PASSWORD des PRIV_PASS_PHRASE USERNAME Specify a user name.
802.1x Radius Configuration, Port Authentication Radius Configuration Radius Status: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use dot1x system-auth-ctrl command to globally enable authentication. Use no dot1x system-auth-ctrl command to globally disable authentication. 3. Command Syntax: (no) dot1x system-auth-ctrl 4.
switch_a(config)# Secret Key: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to set the shared secret key between a Radius server and a client. 3. Command Syntax: (no) radius-server host IP-ADDRESS key KEY IP-ADDRESS A.B.C.D specifies the IP address of the radius server host. KEY specifies the secret key shared among the radius server and the 802.1x client. 4.
switch_a(config)# Retransmit: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to specify the number of times the Switch transmits each radius request to the server before giving up. 3. Command Syntax: radius-server retransmit RETRIES no radius-server retransmit RETRIES <1-100> Specifies the retransmit value. Enter a value in the range 1 to 100. 4.
switch_a(config-if )# Port Control: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if )# 2. Usage: Use this command to force a port state. Use no dot1x port-control command to remove a port from the 802.1x management. 3.
3. Command Syntax: dot1x timeout re-authperiod SECS no dot1x timeout re-authperiod SECS <1-4294967295> Specify the seconds between reauthorization attempts. The default time is 3600 seconds. 4.
Other Protocols GVRP, IGMP Snooping, NTP GVRP GVRP: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use set gvrp enable bridge command to enable (set) and set gvrp disable bridge command to disable (reset) GVRP globally for the bridge instance. This command does not enable/disable GVRP in all ports of the bridge.
The following example enables dynamic VLAN creation for bridge GROUP (1): switch_a(config)#set gvrp dynamic-vlan-creation enable bridge 1 switch_a(config)# Per port setting: GVRP: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use set port gvrp enable command to enable and set port gvrp disable command to disable GVRP on a port or all ports in a bridge. 3.
The following example sets GVRP applicant state to active on the interface fe1 (port 1): switch_a(config)#set gvrp applicant state active fe1 switch_a(config)# Per port setting: GVRP registration: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to set GVRP registration to normal, fixed, and forbidden registration mode for a given port. 3.
(VLAN) when no multicast routing protocol is configured in the subnet (VLAN). When enabled, the IGMP Snooping querier sends out periodic IGMP queries for all interfaces on that VLAN. Use the no ip igmp snooping querier command to disable IGMP querier configuration. 3. Command Syntax: (no) ip igmp snooping querier 4. Example: The following example enables IGMP snooping querier: switch_a(config)# ip igmp snooping querier switch_a(config)# IGMP mode: Passive: 1.
Use ip igmp version command to set the current IGMP protocol version on an interface. To return to the default version, use the no ip igmp version command. 3. Command Syntax: ip igmp version VERSION no ip igmp version VERSION IGMP protocol version number. 4. Example: The following example sets the IGMP protocol version 3 on vlan1.1: switch_a(config)#interface vlan1.1 switch_a(config-if )#ip igmp version 3 switch_a(config-if )# Fast-leave: 1.
Then logon to Interface mode. vlan1.1 means vlan 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface vlan1.1 switch_a(config-if )# 2. Usage: Use ip igmp query-interval command to configure the frequency of sending IGMP host query messages. To return to the default frequency, use the no ip igmp query-interval command. 3.
4. Example: The following example configures a maximum response time of 8 seconds on vlan1.1: switch_a(config)#interface vlan1.1 switch_a(config-if )#ip igmp query-max-response-time 8 switch_a(config-if )# IGMP passive snooping: Static mc router port: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. vlan1.1 means vlan 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface vlan1.1 switch_a(config-if )# 2.
2. Usage: Use ip igmp snooping report-suppression command to enable report suppression for IGMP versions 1 and 2. Use the no ip igmp snooping report-suppression command to disable report suppression. 3. Command Syntax: (no) ip igmp snooping report-suppression 4. Example: The following example enables report suppression for IGMPv2 reports on vlan1.1: switch_a(config)#interface vlan1.
Use this command to specify the IP address or Domain name of NTP server. 3. Command Syntax: ntp server IP-ADDRESS｜DOMAIN-NAME IP-ADDRESS A.B.C.D specifies the IP address of NTP server. DOMAIN-NAME Specifies the Domain name of NTP server. 4. Example: The following example specifies the IP address (192.168.1.100) of NTP server: switch_a(config)#ntp server 192.168.1.100 switch_a(config)# Sync Time: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode).
The following example sets time zone (Canada/Yukon): switch_a(config)#clock timezone YST9YDT switch_a(config)# Polling Interval: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to specify the polling interval. 3. Command Syntax: ntp polling-interval MINUTE MINUTE <1-10080> The polling interval. Enter a value in the range 1 to 10080 minutes. 4.
TIMEZONE Specifies the daylight saving timezone. DAY <1-31> Specifies from 1 to 31. MONTH <1-12> Specifies from January to December. HOUR <0-23> Specifies from 0 to 23. MINUTE <0-59> Specifies from 0 to 59. OFFSET <1-1440> Specifies from 1 to 1440 minutes. no clock summer-time 4.
Specifications Applicable Standards Switching Method Forwarding Rate 10Base-T 100Base-TX 100Base-FX 1000Base-T/SX/LX Performance Cable 10Base-T 100Base-TX 1000Base-T 100Base-FX 1000Base-SX/LX LED Indicators Dimensions Net Weight Power Input Operating Voltage & Max. Current Consumption Power Consumption Operating Temperature IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX, 100Base-FX IEEE 802.3ab 1000Base-T IEEE 802.
Appendix A DB9 DCE pin assignment Pin no.
Appendix B Time Zone Europe MEZ-1MESZ MET-1METDST EET-2EETDST GMT0BST WET0WETDST PWT0PST MST-3MDT EUT-1EUTDST EUT-2EUTDST EUT-3EUTDST EUT-4EUTDST EUT-6EUTDST EUT-8EUTDST Russian Federation RFT-2RFTDST RFT-3RFTDST RFT-4RFTDST RFT-5RFTDST RFT-6RFTDST RFT-7RFTDST RFT-8RFTDST RFT-9RFTDST RFT-10RFTDST IES-1081 User Manual Country and City Lists Europe/Vienna, Europe/Berlin, Europe/Zurich Africa/Tunis, CET, MET, Europe/Tirane, Europe/Andorra, Europe/Brussels, Europe/Prague, Europe/Copenhagen, Europe/Paris, Eu
RFT-11RFTDST RFT-12RFTDST North America PST8PDT MST7MDT MST7 CST6CDT EST5EDT AST4ADT EST5 AST10ADT YST9YDT NST3:30NDT NAST3NADT NAST9NADT Asia/Sakhalin, Asia/Magadan Asia/Kamchatka, Asia/Anadyr America/Los_Angeles, US/Pacific-New, PST8PDT, US/Pacific, SystemV/PST8PDT America/Denver, America/Boise, America/Cambridge_Bay, America/Shiprock, MST7MDT, Navajo, US/Mountain, SystemV/MST7MDT America/Phoenix, MST, US/Arizona, SystemV/MST7 America/Chicago, America/North_Dakota/Center, America/Menominee, America/C
WBST4WBDT ACRE5 NORO2 CST4CDT EIST6EIDT Asia MST-8 CST-8 Oceania CST-9:30CDT EST-10EDT LHT-10:30LHDT TST-10TDT NZST-12NZDT CIST-12:45CIDT Africa SAST-2 EST-2EDT UAEST-4 IST-3IDT JST-2JDT SST-2SDT Universal UCT IES-1081 User Manual America/Bahia, America/Sao_Paulo, America/Cuiaba, America/Montevideo, America/Catamarca, America/Rosario, Brazil/East America/Campo_Grande, America/Boa_Vista, America/Manaus, Atlantic/Stanley, America/Asuncion, Brazil/West America/Rio_Branco, America/Porto_Acre, Brazil/Acre A
UCT1 UCT2 UCT3 UCT4 UCT5 UCT6 UCT7 UCT8 UCT9 UCT10 UCT11 UCT-1 UCT-2 UCT-3 IES-1081 User Manual Etc/Zulu, Etc/Greenwich, Etc/GMT-0, Etc/GMT+0, Etc/GMT0, Africa/Timbuktu, GMT+0, GMT-0, GMT0, Greenwich, Iceland, UCT, UTC, Universal, Zulu Atlantic/Cape_Verde, Etc/GMT+1 Atlantic/South_Georgia, Etc/GMT+2 Antarctica/Rothera, America/Belem, America/Cayenne, America/Paramaribo, Etc/GMT+3 America/Anguilla, America/Antigua, America/Barbados, America/Dominica, America/Grenada, America/Guadeloupe, America/Marti
UCT-4 UCT-5 UCT-5:45 UCT-6 UCT-6:30 UCT-7 UCT-8 UCT-9 UCT-9:30 UCT-10 UCT-11 UCT-11:30 UCT-12 UCT-13 JST KST UCT-3:30 UCT-4:30 IST-2IDT CST6MEX CST6 EET-2EETDST2 EET-2EETDST3 EET-2EETDST2W2K UCT-14 UCT9:30 IES-1081 User Manual Asia/Qatar, Asia/Riyadh, Asia/Aden, Etc/GMT-3 Indian/Mauritius, Indian/Reunion, Indian/Mahe, Asia/Muscat, Etc/GMT-4 Indian/Kerguelen, Indian/Maldives, Asia/Karachi, Asia/Dushanbe, Asia/Ashgabat, Asia/Samarkand, Asia/Tashkent, Etc/GMT-5 Asia/Katmandu Antarctica/Mawson, Antarc
UCT12 North America (Canada) PST8PDT_CA MST7MDT_CA CST6CDT_CA EST5EDT_CA AST4ADT_CA North America (Cuba) EST5EDT_CU North America (Haiti) EST5EDT_HT North America (Mexico) PST8PDT_MX MST7MDT_MX Etc/GMT+12 America/Vancouver, America/Dawson_Creek, America/Whitehorse, America/Dawson, Canada/Pacific America/Edmonton, America/Yellowknife, America/Inuvik, Canada/Mountain America/Rainy_River, America/Winnipeg, America/Rankin_Inlet, Canada/Central America/Montreal, America/Toronto, America/Thunder_Bay, America/N
IES-1081 User Manual Page 150
