Sophia™ 2.4” Digital Video Baby Monitor / Moniteur vidéo bébé numérique 2,4po / Video Monitor Digital para Bebé 2.4” User Manual / Manuel de l’utilisateur / Manual del usuario WARNING • MISE EN GARDE • ADVERTENCIA Strangulation Hazard! Risque de Strangulation ! Peligro de Estrangulación ! Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft [0.9 m] away). Enfants ont étranglé dans les cordons.
SAFETY WARNINGS CAUTION: Keep small parts away from children. This product cannot replace responsible adult supervision. Use only with provided power supply. Strangulation Hazard: Children can become entangled in cords. Power cords should be kept more than 3 feet away from the crib and baby’s reach at all times. Baby monitors with power cords should never be hung on or near the crib. The socket-outlet shall be installed near the equipment and shall be easily accessible.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
WARRANTY INFORMATION Please visit our website at www.mylevana.com for information about your product’s warranty We take quality very seriously. This is why all of our products come with a one-year warranty from the original purchase date against defects in workmanship and materials. If you have warranty or support issues please contact us using any of the following methods: Web: www.mylevana.com Support: www.mylevana.
TABLE OF CONTENTS Safety Warnings................................................................................................................................. 2 FCC Statement................................................................................................................................... 3 Disclaimers.......................................................................................................................................... 3 Warranty........................................
BUTTONS AND CONNECTIONS 1 9 2 10 5 3 6 7 4 13 14 11 15 12 16 8 1 LED Sound Bar 9 Antenna 2 LCD Screen 10 Night Vision LEDs 3 Power & Screen ON/OFF 11 Camera Lens Press and hold to turn monitor ON/OFF; Press once to turn screen ON/OFF 12 Microphone 4 Volume - & Left 13 Nightlight 5 Microphone 14 Night Vision Light Sensor 6 Menu & Save 15 On/OFF Button 7 16 Power LED Volume + & Right 8 Talk To Baby™ Press and hold to talk, release to listen 6
BUTTONS AND CONNECTIONS 1 2 6 7 3 8 4 5 9 1 Antenna 6 Speaker 2 Speaker 7 Pairing Button 3 Table Stand 8 Antenna 4 Battery Compartment 9 Power Input 5 Power Input SETUP Battery Installation - Monitor 1. Remove the Table Stand. 2. Slide Battery Compartment Cover down to remove. 3. Insert the included rechargeable battery. Ensure the battery connectors on the battery line up with the connectors inside the battery compartment. + – 4. Slide the Battery Cover back into place. + – 5.
SETUP Battery Installation - Camera (optional) The camera unit can be powered using 4 AAA batteries (not included) instead of the included adapter. 1. Gently remove the Battery Compartment Cover on the bottom of the camera base, using a small phillips (cross) head screwdriver. 2. Insert 4 AAA batteries in the compartment (not included), paying close attention to the labelled polarity markings. 3. Replace the battery compartment cover using the small screwdriver. 4.
SETUP Get the Most Out of Your Rechargeable Battery Fully charge your battery before first use Turn LCD screen OFF. Press POWER button on the front of monitor ONCE. Charge battery before battery is fully drained. PEEP Mode: After 1 minute of inactivity, monitor enters standby/ sleep mode (when activated) Avoid extreme heat or cold as this will affect the battery life.
SETUP Pairing the Monitor and the Camera(s) The camera and monitor come paired (connected) to each other automatically. However, if upon opening this package the devices do not automatically connect and transmit, you may do so manually. To pair additional cameras, repeat steps below and be sure to assign a different camera number to each additional camera. Note: Before you begin pairing, be sure to have the monitor and the camera(s) side by side.
SETUP Mounting the Camera on a Tabletop Safely 1. Place the Camera on a tabletop no less than 3 feet away from your baby’s crib. 2. Feed the power cord down the back of the table or use wall clips (not included) to secure the cord away so the baby cannot reach it. 3. Plug in the power cord, check the monitor to ensure that you can see and hear your child. 3 ft away Note: Baby monitors with power cords should never be hung on or near the crib as it is a strangulation hazard.
SETUP Mounting the Camera on a Wall Safely Before drilling the holes, it is important to check the reception and camera positioning in the intended location on the wall. Ensure you are hanging the camera no less than 3 feet away from baby’s crib. Note: Baby monitors with power cords should never be hung on or near the crib as it is a strangulation hazard. Power cords should be kept no less than 3 feet away from the crib and the baby’s reach at all times. 1. Pre-drill two holes in the wall using a 3/16”, 4.
OPERATION Adjusting the volume Mute High Note: Placing the monitor and camera too close together will create feedback. DECREASE or MUTE the volume and move the camera away from the monitor. Using the Talk to Baby™ Two-Way Intercom With the simple press of a button you can talk to your child at any time without entering the nursery. 1. To talk, press and hold the (Talk) button on the front of the monitor and release to listen. 2.
OPERATION Changing the Camera View 1. Press the Menu / Save button and use the Navigational – arrow keys + to navigate the Camera View options. 2. Press the Menu / Save button to confirm your choice. 3. Use the Navigational arrow keys – + to navigate to EXIT and press the Menu / Save button to exit menu. 4. Repeat the steps above to return to any other camera view. • Selecting Scan View cycles through cameras 1 to 4. Each camera view will appear for 6 seconds per camera.
OPERATION Temperature Settings Studies indicate your baby’s room should be between 68-71° F (20- 21° C). This camera includes a temperature monitor for your baby’s room. The temperature of the nursery can be shown with your video monitor’s on-screen display in your choice of Fahrenheit or Celsius so you will always know that your baby is comfortable. 1. Press the Menu / Save button and use the Navigational arrow keys – + to navigate the different Temperature Settings. 2.
TROUBLESHOOTING ISSUE Equipment does not function No reception Reception Interference (static) POSSIBLE SOLUTION • • • • • • • • Noise (static, beeping) The rechargeable battery will not charge • • • Confirm that the Camera and Monitor are ON The battery may be depleted; charge battery The power adapter(s) may not be properly connected Camera and monitor may not be properly paired; move the Camera and Monitor closer together The Camera and Monitor may be too far apart The battery power may be too low
SPECIFICATIONS MONITOR Monitor Type TFT LCD Screen Size 2.4” Resolution 320x240 Frame Rate 25 FPS LCD Brightness Adjustable: 0,1,2,3,4 Frequency 2.4GHz Private Signal Yes Technology Digital FHSS No. of hop/sec 300 No. of hopping channels 19 Channel bandwidth 3.
SPECIFICATIONS CAMERA Image Sensor CMOS Resolution 640 x 480 Viewing Angle 73° Focal Length 4.
NOTES 19
