Manual

ManualsBrandsLet's Go Aero ManualsCarLGT 1 Extension ACC 3075

2120 Naegele Road, Colorado Springs, CO 80904

LGT 1’ Extension

Accessory option for the LittleGiant Trailer™

Part No. ACC 3075

ACC3075rev0614

The 1’ Extension is a bolt together add-on, and

installs at the rear of the trailer.

The LGT Extension transforms the 7’ LittleGiant Trailer into an 8 foot long trailer by inside dimension. This is effectively

that of a full size pick up bed.

Manufactured by Let’s Go Aero in Colorado Springs, CO

Parts Overview

Qty Description Tools Needed

1 Base Panel

2 Side Panels

2 Inside Frame Telescope Tube

2 Outside Frame Telescope Tube

2 C-Channel Extension

2 C-Channel Tie Plate

1 #9 U-Tube (Body Style)

1 #10 U-Tube (End Gate Style)

4 PinNutAssembly(5/16”x1”nethreadbolt,lockwasherandatwasher)

6 5/16” x 2” bolt

6 5/16”Splitlockwasher

6 5/16”Fenderwasher

12 K-LathPhillipsTekscrew

12 Starwasher

12 1”atwasher

2 12”WireHarnessExtensionwithattached

butt connectors

2 1/2” Ribbed cable protector

2 3/8” Ribbed cable protector splice

2 Ring Connector

4 1/4”splitlockwasher

2 Zip tie

4 5/16” Spring Nut

Variable speed drill

5/16” socket

5/16”wrench

7/16”wrench

Philllipspowerbit

Wire Stripper/crimper

Summary of content (4 pages)

PAGE 1
LGT 1’ Extension Accessory option for the LittleGiant Trailer™ 2120 Naegele Road, Colorado Springs, CO 80904 Part No. ACC 3075 Manufactured by Let’s Go Aero in Colorado Springs, CO The LGT Extension transforms the 7’ LittleGiant Trailer into an 8 foot long trailer by inside dimension. This is effectively that of a full size pick up bed. The 1’ Extension is a bolt together add-on, and installs at the rear of the trailer.
PAGE 2
LGT 1’ Extension Assembly Step 1: Remove Hardwares Remove rear end gate supports and hardware from rear of trailer body to include latches, brackets, and tail light assemblies. Set aside. Step 2: Install Extension Tubes Locate the two Inside Frame Tubes (IFT) and the four 5/16” Spring Nuts. Using the 7/16” wrench (or a stick of wood) push a spring nut into one of the tubes so that it aligns with one of the holes in the tube. Repeat this process for the other three spring nuts and the second IFT.
PAGE 3
LGT 1’ Extension Step 6: Attach Tie Plates Remove the two 5/16” X 1” bolts from the #8 U-Tube Pin Nuts. Slip the two C-Channel Tie Plates into the C-Channel and secure with four 5/16” X 1” bolts, four 5/16” lock washers, and four 5/16” flat washers, using two sets that were removed and two sets from your extension kit. You may wish to use a clamp of the type shown to aid in assembly.
PAGE 4
LGT 1’ Extension Step 11 Take the Wire Harness Extension and crimp each butt connector to its counterpart on the trailer’s wire harness. The yellow wire will connect to the green trailer wire when working on the passenger side. Step 12 Reattach the two tail light brackets. Determine how much of the extended wire harness to remove and make the necessary cuts. Again, strip about ½” insulation from each wire, and thread into the corresponding holes on the rear of the tail light.