Owner manual

L Firmware 1.37 - 09/2006 675
9400 HighLine | Parameter setting & configuration
Index
CAN module is missing or incompatible 495
Digital frequency module is missing or incompatible
494
Ethernet module is missing or incompatible 494
ICM module missing or incompatible 494
Module changed during operation 450
Module has been changed 453
Module is defective or missing 451
Module is missing or incompatible 493
PROFIBUS module is missing or incompatible 493
Wrong module 452
N
Negative direction of rotation limited 534
Negative limit switch has triggered 533
Negative software limit switch overtravelled 534
New applications loaded 458
No heartbeat signal detected 498
No parameters for module in MXI1 497
No parameters for module in MXI2 497
Number of CRC cycles (C618) 596
O
Offset actual pos. value/setp. (C2578) 624
Operating mode brake (C2580) 625
Optimise response to setpoint changes 93
Overchange 392
Overcurrent detected 470
P
Parameter error information (C217) 565
Parameter set
Variant conflict
497
Version conflict 496
Parameter set faulty 495
Parameter set loaded 496
Parameter set restored 496
Parameter set saved 496
PDO mapping (MXI1)
Faulty configuration
461
PDO mapping (MXI2)
Faulty configuration
461
Permissible angle of rotation (C2595) 627
Permissible direction of rot. (C2707) 639
PF_dnMotorAcc_x (C2685) 636
PF_dnSpeedAdd1_s (C2686) 636
Phase controller gain (C254) 565
Phase currents (C55) 549
Pointer access in impermissible memory area 460
Pos. contr D comp.(C2555) 621
Pos. contr. limitation (C2556) 621
Pos. contr. output (C2558) 621
POS_dnProfileSpeed_s (C2676) 635
POS_dnState (C2675) 634
POS_dwActualProfileNumber (C2674) 634
Position controller gain (C2553) 621
Position encoder 113
Module selected under C00490 not available 473
Position encoder (C490) 585
Position encoder mounting direction (C2529) 616
Position follower
% signals (C2687)
636
Dig. signals (C2689) 637
Pos. signal (C2688) 636
Position setpoint (C2552) 620
Position setpoint (C2573) 623
Position target outside the software limit positions 535
Position value faulty 500
Positioning
% signals (C2677)
635
Dig. signals (C2679) 635
Pos. signals (C2678) 635
Positioning modes 395
Positive direction of rotation limited 534
Positive limit switch has triggered 532
Positive software limit switch overtravelled 534
Power section is defective 449, 451
Power section is not compatible 452
Power stage has been changed 453
Power-on time meter (C179) 561
Profile chaining with velocity changeover (overchange)
392
Program auto-start (C2104) 613
Program name (C2113) 614
Program runtime (C2109) 614
Program status (C2108) 613
Project not available 493
Project not loaded 492
ProjectList.dat file is faulty 491
ProjectList.dat file is invalid 492
ProjectList.dat file is missing 492
ProjectSelection.dat file is faulty 491
ProjectSelection.dat file is invalid 492
ProjectSelection.dat file is missing 491
Q
Quick stop
Dig. signals (C2619)
629
Quick stop by (source) (C159) 559
Quick stop deceleration time (C105) 554
Quick stop S-ramp time (C106) 554
R
Rated motor power (C81) 552
Read error - service register 462
Red. brake chopper threshold (C181) 561
Ref. acceleration 1 (C2645) 632
Ref. acceleration 2 (C2647) 632
Ref. blocking time (C2650) 633