Owner manual

9400 HighLine | Parameter setting & configuration
Parameter reference
Attribute table
656 Firmware 1.37 - 09/2006 L
C02611 S-ramp time for stop 21964 55CC E 1 UNSIGNED_32 1000 ;;
C02612
Ref. for decel. time of stop 21963 55CB E 1 UNSIGNED_32 1 ;;
C02616
STP_dnState 21959 55C7 E 1 INTEGER_32 1 ;
C02617
STP_bStopActive 21958 55C6 E 1 UNSIGNED_32 1 ;
C02619
Quick stop: Dig. signals 21956 55C4 A 4 UNSIGNED_32 1 ;
C02620
Manual jog speed 1 21955 55C3 E 1 INTEGER_32 10000 ;;
C02621
Manual jog speed 2 21954 55C2 E 1 INTEGER_32 10000 ;;
C02622
Manual acceleration 21953 55C1 E 1 INTEGER_32 10000 ;;
C02623
Manual deceleration 21952 55C0 E 1 INTEGER_32 10000 ;;
C02624
Inaccuracy time of manual traversing 21951 55BF E 1 UNSIGNED_32 1000 ;;
C02638
Manual jog status 21937 55B1 E 1 INTEGER_32 1 ;
C02639
Manual control: Dig. signals 21936 55B0 A 7 UNSIGNED_32 1 ;
C02640
Ref. mode 21935 55AF E 1 UNSIGNED_32 1 ;;
C02642
HM position 21933 55AD E 1 INTEGER_32 10000 ;;
C02643
HM target position 21932 55AC E 1 INTEGER_32 10000 ;;
C02644
Ref. speed 1 21931 55AB E 1 INTEGER_32 10000 ;;
C02645
Home acceleration 1 21930 55AA E 1 INTEGER_32 10000 ;;
C02646
Ref. speed 2 21929 55A9 E 1 INTEGER_32 10000 ;;
C02647
Ref. acceleration 2 21928 55A8 E 1 INTEGER_32 10000 ;;
C02648
Home S-ramp time 21927 55A7 E 1 INTEGER_32 1 ;;
C02649
HM torque limit 21926 55A6 E 1 INTEGER_32 100 ;;
C02650
Homing inhibit time 21925 55A5 E 1 UNSIGNED_32 1000 ;;
C02651
HM touch probe configuration 21924 55A4 E 1 UNSIGNED_32 1 ;;
C02652
Home position after mains switching 21923 55A3 E 1 UNSIGNED_32 1 ;;
C02653
Max. rot. angle after mains sw. 21922 55A2 E 1 INTEGER_32 1 ;;
C02656
Current position 21919 559F E 1 INTEGER_32 10000 ;
C02657
HM_dnState 21918 559E E 1 INTEGER_32 1 ;
C02658
HM_dnHomePos_p 21917 559D E 1 INTEGER_32 10000 ;
C02659
Homing: Dig. signals 21916 559C A 9 UNSIGNED_32 1 ;
C02674
POS_ dwActualProfileNumber 21901 558D E 1 UNSIGNED_32 1 ;
C02675
POS_dnState 21900 558C E 1 INTEGER_32 1 ;
C02676
POS_dnProfileSpeed_s 21899 558B E 1 INTEGER_32 10000 ;
C02677
Positioning: % signals 21898 558 A A 2 INTEGER_32 100 ;
C02678
Positioning: Pos. signals 21897 5589 A 2 INTEGER_32 10000 ;
C02679
Positioning: Dig. signals 21896 5588 A 10 UNSIGNED_32 1 ;
C02680
Source position setpoint 21895 5587 E 1 UNSIGNED_32 1 ;;
C02681
Source add. speed 21894 5586 E 1 UNSIGNED_32 1 ;;
C02685
PF_dnMotorAcc_x 21890 5582 E 1 INTEGER_32 10 ;
C02686
PF_dnSpeedAdd1_s 21889 5581 E 1 INTEGER_32 10 ;
C02687
Position follower: % signals 21888 5580 A 2 INTEGER_32 100 ;
C02688
Position follower: Pos. signal 21887 557F E 1 INTEGER_32 10000 ;
C02689
Position follower: Dig. signals 21886 557E A 2 UNSIGNED_32 1 ;
C02692
SF_dnMotorAcc_x 21883 557B E 1 INTEGER_32 10 ;
C02693
SF_dnSpeedAdd_s 21882 557 A E 1 INTEGER_32 10 ;
C02694
Speed follower: % signals 21881 5579 A 2 INTEGER_32 100 ;
C02695
Speed follower: Dig. signals 21880 5578 A 2 UNSIGNED_32 1 ;
C02698
Torque follower: % signals 21877 5575 A 3 INTEGER_32 100 ;
C02699
Torque follower: Dig. signals 21876 5574 A 2 UNSIGNED_32 1 ;
C02700
Software limit positions are active 21875 5573 E 1 UNSIGNED_32 1 ;;
C02701
Software limit positions 21874 5572 A 2 INTEGER_32 10000 ;;
C02702
Limitations effective 21873 5571 E 1 UNSIGNED_32 1 ;;
Code Name Index Data Access
dec hex DS DA DT Factor R W CINH