User guide

Lenze · 9400 function library · Reference manual · DMS 6.7 EN · 08/2014 · TD05 661
6 Table of attributes
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
L_LdMPot
C05122 Positive speed 19453 4BFD S 1 INTEGER_32 10000 
C05123 Negative speed 19452 4BFC S 1 INTEGER_32 10000 
C05124 Ramp: Acceleration 19451 4BFB S 1 UNSIGNED_32 1000 
C05125 Ramp: Deceleration 19450 4BFA S 1 UNSIGNED_32 1000 
C05126 Ramp: Motor potentiometer off 19449 4BF9 S 1 UNSIGNED_32 1000 
C05127 Speed at the output 19448 4BF8 S 1 INTEGER_32 10000 
C05128 Speed unit 19447 4BF7 S 1 VISIBLE_STRING 1 
C05129 Reference speed 19446 4BF6 S 1 INTEGER_32 10000 
L_LdPosCtrlLin
C05050 Positioning mode 19525 4C45 S 1 UNSIGNED_32 1 
C05051 Mode after deactivation 19524 4C44 S 1 UNSIGNED_32 1 
C05052 Unit 19523 4C43 A 2 VISIBLE_STRING 1 
C05053 Speeds 19522 4C42 A 2 INTEGER_32 10000 
C05054 Reference speed 19521 4C41 S 1 INTEGER_32 10000 
C05056 Ramps 19519 4C3F A 3 INTEGER_32 1000 
C05065 Speed at the output 19510 4C36 S 1 INTEGER_32 10000 
C05067 Position at the output 19508 4C34 S 1 INTEGER_32 10000 
C05069 Set position reached 19506 4C32 S 1 UNSIGNED_8 1 
L_LdSetAxisVelocity
C05034 Status 19541 4C55 S 1 INTEGER_32 1 
C05035 Unit 19540 4C54 A 2 VISIBLE_STRING 1 
C05036 Speed at the output 19539 4C53 S 1 INTEGER_32 10000 
C05037 Master speed 19538 4C52 S 1 INTEGER_32 10000 
C05041 Measured cycle 19534 4C4E S 1 INTEGER_32 10000 
C05042 Measured TP deviation 19533 4C4D S 1 INTEGER_32 10000 
C05043 Position at the output 19532 4C4C S 1 INTEGER_32 10000 
C05048 TP: Deviation detected 19527 4C47 S 1 UNSIGNED_8 1 
C05049 Cycle start 19526 4C46 S 1 UNSIGNED_8 1 
L_LdSyncOperation
C05090 Coupling measuring systems X and Y 19485 4C1D S 1 UNSIGNED_32 1 
C05091 User-defined units 19484 4C1C A 2 VISIBLE_STRING 1 
C05092 Coupling factors 19483 4C1B A 2 INTEGER_32 10000 
C05093 Cycles 19482 4C1A A 2 INTEGER_32 10000 
C05094 Position X at the input 19481 4C19 S 1 INTEGER_32 10000 
C05095 Trimming X 19480 4C18 S 1 INTEGER_32 10000 
C05096 Speed X at the output 19479 4C17 S 1 INTEGER_32 10000 
C05097 Speed Y at the output 19478 4C16 S 1 INTEGER_32 10000 
C05098 Position X at the output 19477 4C15 S 1 INTEGER_32 10000 
C05099 Status 19476 4C14 S 1 INTEGER_32 1 
L_LdToolControl
C05142 Status 19433 4BE9 S 1 INTEGER_32 1 
C05143 Unit 19432 4BE8 A 2 VISIBLE_STRING 1 
C05144 Reference speed 19431 4BE7 S 1 INTEGER_32 10000 
C05147 Correction speed at the input 19428 4BE4 S 1 INTEGER_32 10000 
C05148 Speed at the input 19427 4BE3 S 1 INTEGER_32 10000 
C05149 Speed at the output 19426 4BE2 S 1 INTEGER_32 10000 
C05150 Set position at the output 19425 4BE1 S 1 INTEGER_32 10000 
C05151 Actual position at the output 19424 4BE0 S 1 INTEGER_32 10000 
C05152 Following error 19423 4BDF S 1 INTEGER_32 10000 
C05153 Measured TP deviation 19422 4BDE S 1 INTEGER_32 10000 
Code Name Index Data Access
dec hex DS DA DT Factor R W CINH