3 MEMORY CALLER ID TRIM PHONE MODEL PH-543 OPERATING INSTRUCTIONS CALLER ID SHOWS YOU CALLERS NAME & NUMBER 70 NAME & NUMBER CALLER ID MEMORY TONE/PULSE SWITCHABLE DIALING AUTOMATIC TIME & DATE DISPLAY ONE-TOUCH CALLER ID CALL BACK 3 ONE-TOUCH SPEED DIAL BUTTONS 10 TWO-TOUCH SPEED DIAL MEMORY LOCATIONS WALL/DESK USABLE USES 3 SIZE AA BATTERIES (NOT INCLUDED) TO USE THIS CALLER ID FEATURES OF THIS PHONE, YOU MUST SUBSCRIBE TO CALLER ID SERVICE, AND REMEMBER TO INSTALL BATTERIES.
TABLE OF CONTENTS Important Safety Instructions Battery Safety Instructions ○ FCC Information ○ ○ ○ Location of Controls ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3 ○ ○ ○ ○ ○ 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2 ○ ○ ○ 1 ○ ○ Getting Started Step 1: Checking the Package Contents Step 2: Telephone Installation Step 3: Setting up the Telephone Adjust the LCD Contrast Level Basics Making and Receiving Calls Volum
IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following: 1. Read and follow all instructions and warnings. 2. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a slightly dampened cloth only. 3.
BATTERY SAFETY INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY, READ AND FOLLOW THESE INSTRUCTIONS. 1. Use only the following type and size of batteries: 3 size AA alkaline batteries (not included). 2. Do not dispose the batteries into a fire. The cells may explode. Check with local codes for possible special disposal instructions. 3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. 4.
FCC INFORMATION FCC REGISTRATION This telephone set is registered with the FCC based upon compliance with Part 68 of its rules. Connection of this telephone to the nationwide telecommunications network must be through a standard network jack (RJ11W or RJ11C) which you can order from your telephone company, if not already installed. NOTE: FCC registration does not constitute an expressed or implied guarantee of performance.
LOCATION OF CONTROLS 5 4 9 10 3 11 12 6 7 2 1 15 16 17 8 14 13 19 18 1. FLASH BUTTON 2. MUTE BUTTON 3. STORE (MEMORY) BUTTON 4. ONE-TOUCH SPEED DIAL BUTTONS (M1, M2 & M3) 5. HOOK SWITCH 6. AUTO (MEMORY) BUTTON 7. REDIAL/PAUSE BUTTON 8. COILED CORD JACK 9. LINE CORD JACK (on bottom) 10. RINGER (HIGH/LOW/OFF) SWITCH 11. BATTERY COMPARTMENT 12. TELEPHONE NUMBER INDEX 13. NEW CALL INDICATOR 14. CALLER ID DISPLAY 15. UP & DOWN BUTTONS 16. DELETE BUTTON 17. CALLBACK/ADJUST BUTTON 18.
GETTING STARTED Step 1: Checking the Package Contents Your new PH-543 Caller ID Trim Phone has all the features of a 13 memory telephone plus Caller ID display. As you unpack this set, make sure you have the following items in the package.
GETTING STARTED Step 2: Telephone Installation INSTALLING BATTERIES Before you connect the phone cords, follow these steps to install the batteries: 1. Push down the battery door tab with a pen or other pointed object and lift the battery door out (Fig. 1). 2. Insert 3 size AA alkaline batteries as shown inside the battery compartment (Fig. 2). (The negative side () of the battery touches the battery spring.) 3. Replace the battery door and snap it shut (Fig. 3). Fig. 1 Fig. 2 Fig.
GETTING STARTED Step 3: Setting up the telephone SETTING UP LCD CONTRAST, LANGUAGE, AREA CODE, TIME & DATE, AND TONE OR PULSE MODE You may need to set up the LCD contrast, language, area code, time and date, and tone or pulse mode for your telephone when you install the batteries for the first time or when you move to an area that has a different area code. This is necessary because the phone must distinguish local or long distance calls to properly dial calls from the Caller ID list.
NOTE: 1. You do not have to set up the Time and Date manually because the telephone company will automatically update this with the Callers ID information when your phone rings (twice or more). To get back to the standby mode (for dialing), press the DELETE button until the normal display shows. 2. The factorys default setting of the dialing mode is TONE, so you dont need to set it again if you want to use TONE dialing mode. 3.
MEMORY DIALING You can quickly dial the numbers you stored into the 3 one-touch speed dial buttons or 10 two-touch speed dial memories. Storing Phone Number into Memory 1. Press the STORE button, (short for programming) appears in the display. 2. Dial the phone number you want to store. You can store up to 22 digits, including a TONE ( ) and a PAUSE (REDIAL/ PAUSE), each of which is counted as one digit.
CALLER ID FEATURES Understanding the Caller ID service Caller ID allows the callers phone number to be shown on the display after the second ring of the call, also in most cases, the callers name, calling time and date. This informations will be stored automatically. In order to enjoy this feature, you must first subscribe to the Caller ID service. To use the call back feature, set the area code (refer to page 7).
CALLER ID FEATURES Calling back from the Caller ID List A. When Handset is on the Base 1. Display the phone number you want to call back using the UP or DOWN button. 2. Press the CALLBACK/ADJUST button. 3. If the number is only 7-digit (local call), the display will show PICK UP OR ADJ and the phone displayed is 7-digit; if you want the phone number to be 10-digit or 11-digit, press the CALLBACK/ADJUST button once or twice more. 4.
CALLER ID FEATURES Deleting the Data from the Caller ID List TO DELETE THE CALLER ID MEMORY ONE BY ONE 1. Display the callers ID you want to delete. 2. Press the DELETE button twice quickly, the display shows the next or previous call, and the data is deleted. TO DELETE ALL THE CALLER ID MEMORIES 1. Make sure that all NEW calls have been reviewed (NEW CALL INDICATOR at the back of the handset does not flash). 2.
WALL MOUNTING This phone can be mounted on a wall phone plate. If you do not have a modular wall phone plate installed, please consult with your phone company or installer to get one, or see the following for installation without a wall plate. 1. Use the SHORT STRAIGHT WALL CORD, and plug one end into the rear of the phone. 2. Plug the other end into the WALL JACK. 3. Put the phone over the WALL PLATE, make sure both posts fit into slots on the back of the phone.
TROUBLE SHOOTING PROBLEMS CHECK Display shows erroneous figure OR No dial tone or Low dial tone or cannot dial out You have selected the wrong languages. Refer to page 7 and reset the language. It may be helpful to remove the batteries and the line cord for 30 seconds first. Is any plug disconnected from the modular phone plug? Is any jack improperly wired? No dial tone Use another phone to test the jack.
TROUBLE SHOOTING (continued) PROBLEMS CHECK Pick up the phone before the second ring, or your phone received no information or unclear information. Static can cause this Shows in the message. If this condition persists, contact display your local telephone company to ensure there is no problem with your phone line. The DELETE button must be quickly pressed twice to erase a single call record.
LIMITED WARRANTY We warrant this product to be free from defects in material and workmanship under normal use for a period of 1 year after purchase, and we will repair it free of charge or replace it at no charge, should it become defective under this warranty, providing you submit proof of purchase (sales slip) with the set. During the initial 1 year period after original purchase, we will service the set that is returned to LENOXX ELECTRONICS CORP., prepaid, at no charge.
