ThinkStation User Guide Machine Types: 7782, 7783, 7821, 7823, and 7824
Note: Before using this information and the product it supports, be sure to read and understand the “Important safety information” on page iii and Appendix A “Notices” on page 77 . Third Edition (December 2011) © Copyright Lenovo 2011. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents Important safety information . . . . . Service and upgrades . . . . . . Static electricity prevention . . . . Power cords and power adapters . Extension cords and related devices Plugs and outlets. . . . . . . . External devices . . . . . . . . Heat and product ventilation . . . Operating environment . . . . . Modem safety information . . . . Laser compliance statement . . . Power supply statement . . . . . Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the Setup Utility program . . . . . . . Viewing and changing settings . . . . . . . . Using passwords. . . . . . . . . . . . . . Password considerations . . . . . . . . . Power-On Password . . . . . . . . . . Administrator Password . . . . . . . . . Hard Disk Password. . . . . . . . . . . Setting, changing, and deleting a password . Erasing lost or forgotten passwords (clearing CMOS) . . . . . . . . . . . . . . . . Enabling or disabling a device . . . . . . . . Selecting a startup device . . . . .
Important safety information CAUTION: Before using this manual, be sure to read and understand all the related safety information for this product. Refer to the information in this section and the safety information in the ThinkStation Safety and Warranty Guide that you received with this product. Reading and understanding this safety information reduces the risk of personal injury and damage to your product.
or CRU, do not open the static-protective package containing the part until the instructions direct you to install it. When you handle options or CRUs, or perform any work inside the computer, take the following precautions to avoid static-electricity damage: • Limit your movement. Movement can cause static electricity to build up around you. • Always handle components carefully. Handle adapters, memory modules, and other circuit boards by the edges. Never touch exposed circuitry.
Plugs and outlets If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician. Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement. Do not share an electrical outlet with other home or commercial appliances that draw large amounts of electricity; otherwise, unstable voltage might damage your computer, data, or attached devices.
For your safety and to maintain optimum computer performance, always follow these basic precautions with your desktop computer: • Keep the cover closed whenever the computer is plugged in. • Regularly inspect the outside of the computer for dust accumulation. • Remove dust from vents and any perforations in the bezel. More frequent cleanings might be required for computers in dusty or high-traffic areas. • Do not restrict or block any ventilation openings.
Laser compliance statement CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
viii ThinkStation User Guide
Chapter 1. Product overview This chapter provides information about the computer features, specifications, software programs provided by Lenovo, and locations of connectors, components, parts on the system board, and internal drives. Features This section introduces the computer features. The information covers a variety of models.
• Internal speaker Connectivity • 100/1000 Mbps integrated Ethernet controller System management features • Ability to store power-on self-test (POST) hardware test results • Desktop Management Interface (DMI) Desktop Management Interface provides a common path for users to access information about all aspects of a computer, including processor type, installation date, attached printers and other peripherals, power sources, and maintenance history.
Input/Output (I/O) features • 9-pin serial port (one standard) • Eight Universal Serial Bus (USB) connectors (two on the front panel and six on the rear panel) • One Ethernet connector • One Personal System/2 (PS/2) keyboard connector (optional) • One PS/2 mouse connector (optional) • Three audio connectors on the rear panel (audio line-in connector, audio line-out connector, and microphone connector) • Two audio connectors on the front panel (microphone connector and headphone connector) For more informati
Your computer is preinstalled with the Microsoft® Windows® 7 operating system. Operating system(s), certified or tested for compatibility1 (varies by model type) • Linux® • Microsoft Windows XP Professional SP 3 Specifications This section lists the physical specifications for your computer. Dimensions Width: 175 mm (6.89 inches) Height: 425.2 mm (16.74 inches) (floor to top of handle) Depth: 430.8 mm (16.96 inches) Weight Maximum configuration as shipped: 11.2 kg (24.
Software overview The computer comes with a preinstalled operating system and several software programs provided by Lenovo. Software provided by Lenovo The following software programs are provided by Lenovo to help you improve productivity and reduce the cost associated with maintaining your computer. Software programs provided with your computer might vary depending on your computer model type and preinstalled operating system.
Product Recovery The Product Recovery program enables you to restore the contents of the hard disk drive to the factory default settings. ThinkVantage Rescue and Recovery The ThinkVantage Rescue and Recovery program is a one button recovery and restore solution that includes a set of self-recovery tools to help you diagnose computer problems, get help, and recover from system crashes, even if you cannot start the Windows operating system.
Locating connectors, controls, and indicators on the front of your computer Figure 1 “Front connector, control, and indicator locations” on page 7 shows the locations of the connectors, controls, and indicators on the front of your computer. Figure 1.
Locating connectors on the rear of your computer Figure 2 “Rear connector locations” on page 8 shows the locations of the connectors on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer. Figure 2.
Connector Description DisplayPort connector Used to attach a high-performance monitor, a direct-drive monitor, or other devices that use a DisplayPort connector. Note: The DisplayPort connector is not applicable on some models. If your computer has a graphics card installed, be sure to use a monitor connector on the graphics card. Ethernet connector Used to attach an Ethernet cable for a local area network (LAN). Note: To operate the computer within FCC Class B limits, use a Category 5 Ethernet cable.
Locating components Figure 3 “Component locations” on page 10 shows the locations of the various components in your computer. To remove the computer cover, see “Removing the computer cover” on page 26. Figure 3.
Locating parts on the system board Figure 4 “System board part locations” on page 11 shows the locations of the parts on the system board. Figure 4.
Locating internal drives Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and enable your computer to read other types of media. Internal drives are installed in bays. In this manual, the bays are referred to as bay 1, bay 2, and so on.
The following illustration shows the location of the machine type and model label. Figure 6. Machine type and model label 1 Machine type and model label Chapter 1.
14 ThinkStation User Guide
Chapter 2. You and your computer This chapter provides information about accessibility, comfort, and relocating your computer to other countries or regions. Accessibility and comfort Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort. Arrange your workplace and the equipment you use to suit your individual needs and the kind of work that you perform. In addition, use healthy work habits to maximize your performance and comfort while using your computer.
Adjust the monitor so the top of the screen is at, or slightly below, eye level. Place the monitor at a comfortable viewing distance, usually 51 to 61 cm (20 to 24 inches), and position it so you can view it without having to twist your body. Also, position other equipment you use regularly, such as the telephone or a mouse, within easy reach. Glare and lighting Position the monitor to minimize glare and reflections from overhead lights, windows, and other light sources.
Register your computer with Lenovo To register your computer, go to http://www.lenovo.com/register. Then, follow the instructions on the screen to complete the registration. This can help authorities return your computer to you if it is lost or stolen. Registering your computer also enables Lenovo to notify you about possible technical information and upgrades.
For power cord information and part numbers, go to: http://www.lenovo.
Chapter 3. Security This chapter provides information about how to protect your computer from theft and unauthorized use. Security features The following security features are available on your computer: • Computrace Agent software embedded in firmware The Computrace Agent software is an IT asset management and computer theft recovery solution. The software detects if changes have been made on the computer, such as hardware, software, or the computer call-in location.
Locking the computer cover Locking the computer cover helps prevent unauthorized people from gaining access to the inside of your computer. Your computer comes with a padlock loop so that the computer cover cannot be removed when a padlock is installed. Figure 7.
Attaching an integrated cable lock An integrated cable lock, sometimes referred to as the Kensington lock, can be used to secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to the integrated cable lock slot at the rear of your computer and is operated with a key. The cable lock also locks the buttons used to open the computer cover. This is the same type of lock used with many notebook computers.
• Administrator Password: Setting an Administrator Password deters unauthorized users from changing configuration settings. If you are responsible for maintaining the configuration settings of several computers, you might want to set an Administrator Password. For more information, see “Administrator Password” on page 60. You do not have to set any passwords to use your computer. However, using passwords improves computing security.
For more information about how to use your antivirus software, refer to the help system of your antivirus software. Chapter 3.
24 ThinkStation User Guide
Chapter 4. Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for your computer. Handling static-sensitive devices Do not open the static-protective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part. Static electricity, although harmless to you, can seriously damage computer components and parts.
Removing the computer cover Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page iii. This section provides instructions on how to remove the computer cover. CAUTION: Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To remove the computer cover, do the following: 1. Remove any media from the drives and turn off all attached devices and the computer. 2.
Removing and reinstalling the front bezel Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page iii. This section provides instructions on how to remove and reinstall the front bezel. To remove and reinstall the front bezel, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 26. 3.
To install or replace a PCI card, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 26. 3. At the rear of the computer, press the release button 1 to open the card latch 2 . Figure 11. Opening the PCI card latch 4. Depending on whether you are installing or replacing a PCI card, do one of the following: • If you are installing a PCI card, remove the appropriate metal slot cover.
Figure 12. Removing a PCI card Notes: a. The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small amount until it is removed from the card slot. b. If the card is held in place by a retaining latch, disengage the card retaining latch in either of the two ways illustrated, depending on the retaining latch on the PCI card slot. Grasp the card and gently pull it out of the slot. Figure 13. Disengaging the card retaining latch 5.
7. Pivot the card latch to the closed position to secure the PCI card. Figure 14. Installing a PCI card What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 49. Installing or replacing a memory module Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page iii.
5. Remove any parts that might prevent your access to the memory slots. Depending on your computer model, you might need to remove the PCI Express x16 graphics card for easier access to the memory slots. See “Installing or replacing a PCI card” on page 27. 6. Depending on whether you are installing or replacing a memory module, do one of the following: • If you are replacing an old memory module, open the retaining clips and gently pull the memory module out of the memory slot. Figure 15.
7. Position the new memory module over the memory slot. Make sure that the notch 1 on the memory module aligns correctly with the slot key 2 on the system board. Push the memory module straight down into the slot until the retaining clips close. Figure 17. Installing a memory module 8. Reinstall the PCI Express x16 graphics card if you have removed it. What to do next: • To work with another piece of hardware, go to the appropriate section.
• If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear of the optical drive, press the blue release button, and then slide the optical drive out of the front of the computer. Figure 18. Removing the optical drive 5. Install the optical drive retainer on the side of the new optical drive. Figure 19. Installing the optical drive retainer Chapter 4.
6. Slide the new optical drive into the drive bay from the front of the computer until the optical drive snaps into position. Figure 20. Installing the optical drive 7. Connect the signal cable and the power cable to the new optical drive. Figure 21. Connecting the optical drive 8. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 27. What to do next: • To work with another piece of hardware, go to the appropriate section.
This section provides instructions on how to install or replace the card reader. To replace the card reader, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 26. 3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 27. 4.
8. Slide the new card reader into the drive bay until it snaps into position. 9. Reconnect the card reader cable to one of the available front USB connectors on the system board. See “Locating parts on the system board” on page 11. 10. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 27. What to do next: • To work with another piece of hardware, go to the appropriate section.
CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. To replace the power supply assembly, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2.
Note: Use only screws provided by Lenovo. 10. Reconnect the power supply assembly cables to the system board and each of the drives. 11. Secure the power supply assembly cables with the cable clips and ties in the chassis. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 49.
6. Follow this sequence to remove the four screws that secure the heat sink and fan assembly to the system board: a. Partially remove screw 1 , then fully remove screw 2 , and then fully remove screw 1 . b. Partially remove screw 3 , then fully remove screw 4 , and then fully remove screw 3 . Note: Carefully remove the four screws from the system board to avoid any possible damage to the system board. The four screws cannot be removed from the heat sink and fan assembly. Figure 25.
Replacing the primary hard disk drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page iii. This section provides instructions on how to replace the primary hard disk drive. To replace the primary hard disk drive, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 26. 3.
9. To install a new hard disk drive into the blue bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 27. Installing the hard disk drive into the bracket 10. Slide the new hard disk drive into the drive cage until it snaps into position. 11.
13. Press down on the metal latch 2 and pivot the drive cage into place, and then slide it to the front of the computer until it snaps into position. Note: There are two arrows, one on the upper drive cage and one on the hard disk drive cage. The arrows are aligned when the hard disk drive is in the proper position. Figure 28. Installing the primary hard disk drive What to do next: • To work with another piece of hardware, go to the appropriate section.
5. Press the blue release button to release the hard disk drive cage from the chassis. Figure 29. Removing the secondary hard disk drive 6. Remove the hard disk drive cage from the chassis by simply sliding it outward. 7. Pull on the blue handle to release and remove the hard disk drive from the hard disk drive cage. 8. Flex the sides of the blue bracket to remove the hard disk drive from the bracket. 9.
11. Install the hard disk drive cage into the chassis until it snaps into position underneath the metal tab. Make sure that the hard disk drive cage release button is secured in the chassis. Figure 31. Installing the secondary hard disk drive 12. Connect the signal cable and the power cable to the new hard disk drive. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 49.
5. Release the two tabs 1 that attach the front fan assembly to the chassis as shown and then completely remove the front fan from the chassis. Figure 32. Removing the front fan assembly Chapter 4.
6. Insert the two tabs 2 of the new front fan assembly into the corresponding holes in the chassis, and press the other two tabs 1 through the holes until the front fan assembly is secured in place. Figure 33. Installing the front fan assembly 7. Connect the front fan assembly cable to the front fan connector on the system board. See “Locating parts on the system board” on page 11. What to do next: • To work with another piece of hardware, go to the appropriate section.
4. Disconnect the rear fan assembly cable from the rear fan connector on the system board. See “Locating parts on the system board” on page 11. 5. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly by breaking or cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis. Note: The new rear fan assembly will have four new rubber mounts attached. Figure 34. Removing the rear fan assembly 6.
7. Pull on the tips of the rubber mounts until the rear fan assembly is secured in place. Figure 35. Installing the rear fan assembly 8. Connect the rear fan assembly cable to the rear fan connector on the system board. See “Locating parts on the system board” on page 11. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 49.
2. Connect a new keyboard or mouse to one of the USB connectors on the computer. Depending on where you want to connect the new keyboard or mouse, see “Locating connectors, controls, and indicators on the front of your computer” on page 7 or “Locating connectors on the rear of your computer” on page 8. Figure 36. Connecting the USB keyboard or mouse What to do next: • To work with another piece of hardware, go to the appropriate section.
4. Position the computer cover on the chassis so that the rail guides on the bottom of the computer cover engage the rails on the chassis. Then, push the cover to the front of the computer until it snaps into position. Figure 37. Reinstalling the computer cover 5. Install the screws to secure the computer cover. 6. If there is a padlock available, lock the computer cover. See “Locking the computer cover” on page 20. 7. If there is an integrated cable lock available, lock the computer.
Chapter 5. Recovery information This chapter provides information about the recovery solutions provided by Lenovo. This chapter contains the following topics: • Creating and using recovery media • Performing backup and recovery operations • Using the Rescue and Recovery workspace • Creating and using a rescue medium • Installing or reinstalling device drivers • Solving recovery problems Notes: 1.
To create recovery media on the Windows 7 operating system, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Factory Recovery Disks. Then, follow the instructions on the screen. Using recovery media This section provides instructions on how to use recovery media on the Windows 7 operating system. On the Windows 7 operating system, you can use recovery media to restore the contents of the hard disk drive to the factory default state.
3. Click Back up your hard drive and select backup operation options. Then, follow the instructions on the screen to complete the backup operation. Performing a recovery operation This section provides instructions on how to perform a recovery operation using the Rescue and Recovery program on the Windows 7 operating system. To perform a recovery operation using the Rescue and Recovery program on the Windows 7 operating system, do the following: 1.
Note: If the Rescue and Recovery workspace fails to open, see “Solving recovery problems” on page 56. 4. Do one of the following: • To rescue files from your hard disk drive or from a backup, click Rescue files and follow the instructions on the screen. • To restore your hard disk drive from a Rescue and Recovery backup or to restore your hard disk drive to the factory default settings, click Full Restore and follow the instructions on the screen.
3. In the Please select boot device window, select the USB hard disk drive as the first boot device and press Enter. The rescue medium starts. When the rescue medium starts, the Rescue and Recovery workspace opens. The help information for each feature is available from the Rescue and Recovery workspace. Follow the instructions to complete the recovery process.
Reinstalling software programs If a software program you installed on your computer is not working correctly, you might need to remove and reinstall it. Reinstalling overwrites the existing programs files and usually fixes any problems that you might have had with that program. To remove a program in your system, see Microsoft Windows help system for detailed information. To reinstall the program, do one of the following: Note: The method of reinstalling a program varies from program to program.
It is important to create a rescue medium and a set of recovery media as early as possible and store them in a safe place for future use. Chapter 5.
58 ThinkStation User Guide
Chapter 6. Using the Setup Utility program The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1. Make sure your computer is turned off. 2. Repeatedly press and release the F1 key when turning on the computer.
• Have at least eight characters in length • Contain at least one alphabetic character and one numeric character • Setup Utility program and hard disk drive passwords are not case sensitive • Not be your name or your user name • Not be a common word or a common name • Be significantly different from your previous passwords Power-On Password When a Power-On Password is set, you are prompted to type a valid password each time the computer is turned on.
To erase a lost or forgotten password, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 26. 3. Locate the Clear CMOS /Recovery jumper on the system board. See “Locating parts on the system board” on page 11. 4.
1. Turn off your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Please select boot device window displays, release the F12 key. 3. Select the desired startup device and press Enter. The computer will start up from the device you selected. Note: Selecting a startup device from the Please select boot device window does not permanently change the startup sequence.
1. Start the Setup Utility program. 2. From the Setup Utility program main menu, select Power ➙ After Power Loss, and press Enter. 3. Select Power On and press Enter. 4. Press F10 to save changes and exit the Setup Utility program. Press Enter when prompted to confirm the exit. Smart performance choices You can adjust the acoustic and thermal performance of your computer through the Smart Performance Choice menu.
64 ThinkStation User Guide
Chapter 7. Configuring RAID This chapter provides information about how to configure Redundant Array of Independent Disks (RAID) for your computer. Note: The information about configuring RAID in this chapter is applicable only for a Windows environment. For information about configuring RAID in a Linux environment, contact your Linux software provider.
7. Press Enter to initiate volume creation. 8. When prompted, press Y to accept the warning message and create the volume. 9. Return to step 2 to create additional RAID volumes, or select Exit and press Enter. 10. Press Y when prompted to confirm the exit. Deleting RAID volumes This section describes how to use the Intel Matrix Storage Manager option ROM configuration utility to delete RAID volumes. To delete RAID volumes, do the following: 1.
Chapter 8. Updating system programs This chapter provides information about updating the POST and BIOS, and how to recover from a POST and BIOS update failure. Using system programs System programs are the basic layer of software built into your computer. System programs include the POST, the BIOS, and the Setup Utility program. The POST is a set of tests and procedures that are performed each time you turn on your computer.
Updating (flashing) the BIOS from your operating system Note: Because Lenovo makes constant improvements to its Web sites, the Web page contents are subject to change without notice, including the contents referenced in the following procedure. To update (flash) the BIOS from your operating system, do the following: 1. Go to http://support.lenovo.com. 2. Do the following to locate the downloadable files for your machine type: a. In the Enter a product number field, type your machine type and click Go. b.
Chapter 9. Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs. If your computer problem is not described here, see Chapter 10 “Getting information, help, and service” on page 73 for additional troubleshooting resources. Basic troubleshooting The following table provides information to help you troubleshoot your computer problems. Note: If you cannot correct the problem, have the computer serviced.
Symptom Action The operating system does not start. Verify that: The computer beeps multiple times before the operating system starts. Verify that no keys are stuck. • The startup sequence includes the device where the operating system resides. Usually, the operating system is on the hard disk drive. For more information, see “Selecting a startup device” on page 61. Diagnostic programs Diagnostic programs are used to test hardware components of your computer.
Lenovo ThinkVantage Toolbox The Lenovo ThinkVantage Toolbox program helps you maintain your computer, improve computing security, diagnose computer problems, get familiar with the innovative technologies provided by Lenovo, and get more information about your computer. You can use the diagnostics feature of the Lenovo ThinkVantage Toolbox program to test devices, diagnose computer problems, create bootable diagnostic media, update system drivers, and view system information.
Lenovo Diagnostics The Lenovo Diagnostics program is used to detect hardware problems when you cannot start the Windows operating system and all storage devices are unavailable. To run the Lenovo Diagnostics program, do the following: 1. Turn off your computer. 2. Turn on the computer and press F10 repeatedly at startup. 3. After you enter the Lenovo Diagnostics program, select the diagnostic test you want to run. Then follow the instructions on the screen.
Chapter 10. Getting information, help, and service This chapter contains information about help, service, and technical assistance for products manufactured by Lenovo. Information resources You can use the information in this section to access useful resources relating to your computing needs. Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely.
Lenovo Support Web site Technical support information is available on the Lenovo Support Web site at: http://www.lenovo.com/support This Web site is updated with the latest support information such as the following: • Drivers and software • Diagnostic solutions • Product and service warranty • Product and parts details • User guides and manuals • Knowledge base and frequently asked questions Help and service This section contains information about obtaining help and service.
• Installation and maintenance of network operating systems (NOS) • Installation and maintenance of application programs Refer to the ThinkStation Safety and Warranty Guide that comes with your computer for information about your warranty type and duration. You must retain your proof of purchase to obtain warranty service. For a list of the Lenovo Support phone numbers for your country or region, go to http://www.lenovo.
76 ThinkStation User Guide
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo The Lenovo logo Rescue and Recovery ThinkStation ThinkVantage Microsoft and Windows are trademarks of the Microsoft group of companies. Celeron, Intel, Intel Core, Pentium, and Xeon are trademarks of Intel Corporation in the United States, other countries, or both. Linux is a trademark of Linus Torvalds in the United States, other countries, or both.
Appendix B. Regulatory information Export classification notice This product is subject to the United States Export Administration Regulations (EAR) and has an Export Classification Control Number (ECCN) of 4A994.b. It can be re-exported except to any of the embargoed countries in the EAR E1 country list. Television output notice The following notice applies to models that have the factory-installed television-output feature.
Industry Canada Class B emission compliance statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. European Union - Compliance to the Electromagnetic Compatibility Directive This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility.
Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4: Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse B.
82 ThinkStation User Guide
Appendix C. WEEE and recycling information Important information for the European Directive 2002/96/EC EU Only The Waste Electrical and Electronic Equipment (WEEE) mark applies only to countries within the European Union (EU) and Norway. Appliances are labeled in accordance with European Directive 2002/96/EC concerning waste electrical and electronic equipment (WEEE). The Directive determines the framework for the return and recycling of used appliances as applicable throughout the European Union.
If you are a company employee and need to dispose of a Lenovo computer or monitor that is the property of the company, you must do so in accordance with the Law for Promotion of Effective Utilization of Resources. Computers and monitors are categorized as industrial waste and should be properly disposed of by an industrial waste disposal contractor certified by a local government.
Battery recycling information for the European Union Notice: This mark applies only to countries within the European Union (EU). Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union.
86 ThinkStation User Guide
Index A specifications a rescue medium, creating and using Administrator, password 60 antivirus software 6 audio line-in connector 8 audio line-out connector 8 audio subsystem 1 B backup and recovery operations basic troubleshooting 69 boot-block recovery 68 E environment, operating 4 Ethernet 2 Ethernet connector 9 exiting, Setup Utility 63 expansion 3 external options, installing 25 F failure, recovering from POST/BIOS 68 features 1 flashing the BIOS 67 front connectors, controls, indicators 7 front
K R keyboard connector keyboard, replacing 9 48 L Lenovo Solution Center 70 Lenovo ThinkVantage Toolbox 71 Lenovo ThinkVantage Tools 73 Lenovo Welcome 5, 73 locating components 10 M media, creating and using recovery media memory module installing, replacing 30 system board 30 Microphone connector 9 mouse connector 9 mouse, replacing 48 N notices 77 O operations, backup and recovery optical drive, replacing 32 optical mouse cleaning 72 52 P parts replacement, completing 49 password Administrator 6
locating parts 11 locations 11 memory module 30 T temporary startup device 61 the BIOS, updating (flashing) 67–68 trademarks 78 troubleshooting, basic 69 troubleshooting, diagnostics 69 U updating (flashing) the BIOS 67 system programs 67 updating (flashing) the BIOS 68 USB connector 9 using a rescue medium, creating and diagnostic programs 74 documentation 74 other services 75 passwords 59 Setup Utility 59 54 V VGA monitor connector 9 video subsystem 1 viewing and changing settings 59 W warranty info
90 ThinkStation User Guide
Part Number: 0A74582 Printed in USA (1P) P/N: 0A74582 *0A74582*
