ThinkPad® Z60m Hardware Maintenance Manual October 2007 This manual supports: ThinkPad Z60m (MT 2529, 2530, 2531, and 2532)
ThinkPad® Z60m Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 156. Second Edition (October 2007) © Copyright Lenovo 2006, 2007. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . 3 Important service information . . . . . . . . 3 Strategy for replacing FRUs . . . . . . . . . 3 Strategy for replacing a hard disk drive . . . . 4 Important notice for replacing a system board . . 4 How to use error messages . . . . . . . . 4 Strategy for replacing FRUs for CTO, CMV, and GAV 4 Product definition . . . . . . . . . . . 4 FRU identification for CTO, CMV, and GAV products . . . . . . . . . . . . . . .
iv MT 2529, 2530, 2531, and 2532
About this manual This manual contains service and reference information for ThinkPad® Z60m (MT 2529, 2530, 2531, and 2532) products. Use this manual along with the advanced diagnostic tests to troubleshoot problems. The manual is divided into sections as follows: v The common sections provide general information, guidelines, and safety information required in servicing computers. v The product-specific section includes service, reference, and product-specific parts information.
2 MT 2529, 2530, 2531, and 2532
Introduction Important service information Important BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site http://www.lenovo.com/ support Advise customers to contact the Customer Support Center at 800-426-7378 if they need assistance in obtaining or installing any software fixes, drivers, and BIOS downloads. Customers in Canada should call the Customer Support Center at 800-565-3344 for assistance or download information.
Important service information Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect. Strategy for replacing a hard disk drive Always try to run a low-level format before replacing a hard disk drive.
Important service information v The PEW record is the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). v eSupport will show both the CTO and CMV machine type models (Example: 1829-CTO and 1829-W15 will be found on the eSupport site.) v The HMM will have the 4-digit MT and 3-digit CTO model only (Example: 1829-CTO). Again, CMVs are custom models and are not found in the HMM. General Announce Variant (GAV) This is a standard model (fixed configuration).
Important service information For the Remaining FRUs (the complete list of FRUs at the MT Model level) v eSupport can be used to view the complete list of FRUs for a machine type and model. v To view the complete list of FRUs, type in the machine type and model (Example: 1829-CTO) under QUICK PATH. Under “View by Document Type” select PARTS INFORMATION. Under “Filter by Category” select SERVICE PARTS. Under “Parts Information by Date” select SYSTEM SERVICE PARTS.
Diskette compatibility matrix Diskette compatibility matrix The compatibility of each of the drives with the diskettes for it is as follows: Diskette drive Diskette capacity Compatibility 3.5-inch 1.0 MB Read and write 2.0 MB Read and write 4.0 MB Not compatible Safety notices: multilingual translations In this manual, safety notices appear in English with a page number reference to the appropriate multilingual, translated safety notice found in this section.
Safety notices Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium.
Safety notices Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Safety notices Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium.
Safety notices Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes.
Safety notices Safety notice 7 DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.
Safety information Safety information The following section presents safety information with which you need to be familiar before you service a ThinkPad computer. General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force.
Safety information Important Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock. v Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet.
Safety information v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) v If an electrical accident occurs: – Use caution; do not become a victim yourself. – Switch off power. – Send another person to get medical aid.
Safety information 9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with. Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects.
Laser compliance statement Laser compliance statement Some models of ThinkPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
Laser compliance statement A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir.
General descriptions The descriptions in this chapter apply to any ThinkPad model that has the PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to your particular computer. Read this first Before you go to the checkout guide, be sure to read this section. Important notes v Only certified trained personnel should service the computer. v Before replacing any FRU, read the entire page on removing and replacing FRUs. v When you replace FRUs, use new nylon-coated screws.
Read this first Following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use.
Related service information Related service information This section provides information about the following: v “Service Web site” v “Restoring the pre-installed system” v “Passwords” v “Power management” on page 24 Service Web site When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
Related service information If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered. Exception: If only an SVP is installed, the password prompt does not appear when the operating system is booted. Power-on password: A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted.
Related service information 1. Turn on the computer; then, while the “To interrupt normal startup, press the blue ThinkVantage button” message is displayed at the lower-left of the screen, press the ThinkVantage button. Rescue and Recovery screen opens. Note: To check whether the ThinkPad computer supports the Passphrase function, enter BIOS Setup Utility and go to Security --> Password. If Using Passphrase item is displayed in the menu, this function is available on the ThinkPad computer. 2.
Related service information Power management To reduce power consumption, the computer has three power management modes: screen blank, standby, and hibernation. Screen blank mode Screen blank mode has three variants, as follows: 1. If you press Fn+F3, or if the time set on the “LCD off timer” in the BIOS Setup Utility expires, v The LCD backlight turns off. v The hard disk drive motor stops. v The speaker is muted. 2.
Related service information Note: The computer does not accept any input immediately after it enters standby mode. Wait a few seconds before taking any action to reenter operation mode. Hibernation mode In hibernation mode, the following occurs: v The system status, RAM, VRAM, and setup data are stored on the hard disk. v The system is powered off. Note: If the computer enters the hibernation mode while it is docked to the docking station, do not undock it before resuming normal operation.
Checkout guide Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Checkout guide Note: In the following procedure, you can select an item not only with the arrow keys, but also with the TrackPoint pointer. Instead of pressing Enter, click the left button. 1. Insert the PC-Doctor disk into the diskette drive; then power on the computer. If the computer cannot be powered on, go to “Power system checkout” on page 30, and check the power sources. If an error code appears, go to “Symptom-to-FRU index” on page 45. On the first screen, select the model and press Enter.
Checkout guide Diagnostics Interactive Tests Hardware Info Utility Quit F1=Help Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Serial Ports Parallel Ports Fixed Disks Diskette Drives Other Devices Communication Wireless LAN Memory Test - Full Memory Test - Quick PC-DOCTOR 2.0 Copyright 2002 PC-Doctor, Inc. All Rights Reserved. Use the cursor keys and ESC to move in menus. Press ENTER to select.
Checkout guide v v v v v v v v Logical Disk Drives VGA Information IDE Drive Info PCI Information PNPISA Info SMBIOS Info VESA LCD Info Hardware Events Log Utility v v v v v v v v v v v Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick Erase Hard Drive PC-Doctor for Windows This product is designed to help you troubleshoot and resolve problems related to your computer.
Checkout guide Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checkout guide Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack. If the charge indicator still does not turn on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section.
Checkout guide Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board. v If the voltage is not correct, replace the backup battery. v If the backup battery discharges quickly after replacement, replace the system board.
ThinkPad Z60m Product overview . . . . . . . . . . . . Specifications . . . . . . . . . . . . . Status indicators . . . . . . . . . . . . FRU tests . . . . . . . . . . . . . . Fn key combinations . . . . . . . . . . Symptom-to-FRU index . . . . . . . . . . Numeric error codes . . . . . . . . . . Error messages . . . . . . . . . . . . Beep symptoms . . . . . . . . . . . . No-beep symptoms . . . . . . . . . . . LCD-related symptoms . . . . . . . . . Intermittent problems . . . . . . . . . .
Product overview Product overview This section presents the following product-unique information: v “Specifications” v “Status indicators” on page 37 v “FRU tests” on page 40 v “Fn key combinations” on page 42 Specifications The following table lists the specifications of the ThinkPad Z60m: Feature Description Processor v v v v v v v Bus architecture v v v v v Graphic memory chip v Intel 915GM v 64-MB GDDR SDRAM (ATI M22-CSP64) v 128-MB GDDR SDRAM (ATI M24-CSP128) Display v 15.
Product overview Feature Description Standard memory v 256-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × v 512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × v 512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × and 256-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 v 512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × v 1-GB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 1 1 1 2 Optional memory v 256-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 v 512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1 v 1-GB DDR2-533 SDRA
Product overview 36 Feature Description Infrared transfer v IrDA 1.
Product overview Status indicators The system status indicators show the status of the computer, as follows: 1 2 3 4 5 6 7 8 9 10 11 10 9 8 ThinkPad Z60m 37
Product overview Indicator Meaning 1 Wireless status Green: The wireless feature (the IEEE 802.11 standard) is on, and the radio link is ready for use. Blinking green: Data is being transmitted. 2 Bluetooth status Green: Bluetooth wireless is operational. This indicator is on when Bluetooth wireless is on and not in suspend mode. R 3 Wireless WAN status Green: The wireless feature (the IEEE 802.11 standard) is on, and the radio link is ready for use.
Product overview Indicator Meaning 8 Battery status Green: The battery is charged between 80% to 100% of the capacity, and being discharged between 20% to 80% of the capacity. Blinking green: The battery is charged between 20% to 80% of the capacity, and being charged. Orange: The battery is charged between 5% and 20% of the capacity, and being discharged. Blinking orange (slow): The battery is charged between 5% to 20% of the capacity, and being charged.
Product overview FRU tests The following table shows the test for each FRU. FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the docking station or the port replicator is attached to the ThinkPad computer, undock it. Place the computer on a horizontal surface, and run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test. Note: Do not apply any physical shock to the computer while the test is running.
Product overview FRU Applicable test Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics --> Memory Test—Quick. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. 3. If the test does not detect the error, run Diagnostics --> Memory Test—Full. Fan 1. Turn on the computer and check the air turbulence at the louver near the PC Card slot. 2. Run Diagnostics --> ThinkPad Devices --> Fan.
Product overview Fn key combinations The following table shows the function of each combination of Fn with a function key. Key combination Description Fn+F1 Reserved. Fn+F2 Reserved. Fn+F3 Select a power scheme that has been created by Power Manager. Fn+F4 Put the computer in standby mode. To return to normal operation, press the Fn key only, without pressing a function key. Note: In Windows 2000 and Windows XP, this combination of keys functions as a sleep button.
Product overview Key combination Description Fn+F8 Change the settings of the TrackPoint and the touch pad. Fn+F9 Open the ThinkPad EasyEject Utility screen. Buttons for the following choices are displayed: v Eject ThinkPad PC from Dock: This button is displayed only if the ThinkPad computer has been attached to a ThinkPad Dock II or a ThinkPad Mini Dock. The computer can be detached from the ThinkPad Dock II or the ThinkPad Mini Dock.
Product overview 44 Key combination Description Fn+PgUp Turn the ThinkLight on or off. Note: This function is supported only on the ThinkPad computers that have the ThinkLight. The on or off status of the ThinkLight is shown on the screen for a few seconds when you press Fn+PgUp. Fn+Home The computer display becomes brighter. Fn+End The computer display becomes dimmer. Fn+Spacebar Enable the FullScreen Magnifier function. Fn+PrtSc Has the same function as the SysRq key.
Symptom-to-FRU index Symptom-to-FRU index The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type. Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or action, in sequence.” If replacing a FRU does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU.
Symptom-to-FRU index 46 Symptom or error FRU or action, in sequence 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1. Run BIOS Setup Utility, and then save current setting by pressing F10. 2. System board. 0192 System Security— Embedded Security hardware tamper detected. System board. 0199 System Security— Security password retry count exceeded. 1.
Symptom-to-FRU index Symptom or error FRU or action, in sequence 0252 Password checksum bad—The password is cleared. Reset the password by running BIOS Setup Utility. 0260 System timer error. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 3. System board. 0270 Real-time clock error. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2.
Symptom-to-FRU index Symptom or error FRU or action, in sequence 2010 Warning: Your internal hard disk drive (HDD) may not function correctly on this system. Ensure that your HDD is supported on this system and that the latest HDD firmware is installed.
Symptom-to-FRU index Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Symptom-to-FRU index Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 45. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2.
Symptom-to-FRU index LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns.
Symptom-to-FRU index Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
FRU replacement notices FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten.
FRU replacement notices v “Retaining the UUID” v “Reading or writing the ECA information” Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer. If you replace the system board, you must restore the serial number of the system unit to its original value.
FRU replacement notices To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the ThinkPad Hardware Maintenance Diskette Version 1.73 or later. 1. Insert the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 6. Set ECA Information. 3. To read ECA information, select 2. Read ECA/rework number from EEPROM and follow the instruction. 4. To read box build date, select 5.
Removing and replacing a FRU Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 53. 3. Begin by removing any FRUs that have to be removed before the failing FRU.
Removing and replacing a FRU 1010 Battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Unlock the battery release lever 1 . Holding the battery release lever in the unlocked position 2 , remove the battery pack in the direction shown by arrow 3 .
Removing and replacing a FRU When installing: Install the battery pack along the slide rails of the slot. Then make sure that the battery release lever is locked, as in this figure.
Removing and replacing a FRU 1020 Ultrabay Enhanced device Note Ultrabay Enhanced does not accept any of the following devices: v Ultrabay Plus devices v Ultrabay 2000 devices Note: When you release the switch in step 1 , the lever pops out. In step 2 , pull the lever a little to release the device from the bay.
Removing and replacing a FRU 1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails For access, remove this FRU: v “1010 Battery pack” on page 57 Attention v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible.
Removing and replacing a FRU 3 2 4 When installing: Make sure that the hard disk drive connector is attached firmly.
Removing and replacing a FRU 5 6 6 When installing: Rubber rails of the hard disk drive must be attached to the replacement drive. Otherwise the hard disk drive cannot be properly installed to the computer.
Removing and replacing a FRU 1040 Palm rest or palm rest with fingerprint reader For access, remove this FRU in order: v “1010 Battery pack” on page 57 Notes In models with the fingerprint reader, the sensor has been attached to the palm rest FRU as the child part. If the fingerprint reader has any defects and needs to be replaced, you need to replace the palm rest by the procedures given in this section. These procedures are the same for a palm rest with or without a fingerprint reader.
Removing and replacing a FRU In step 2 , press the left and right sides of the palm rest toward the center to release the side latches, as in this figure. Then release the latches indicated by arrow 3 . 3 2 2 Pull the palm rest a little in the direction shown by arrow 4 , and then detach the touch pad connector by pulling the tab with your fingers in the direction shown by arrow 5 . 4 5 When installing: Make sure that the touch pad connector is attached firmly.
Removing and replacing a FRU 1050 DIMM For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 1 2 1 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
Removing and replacing a FRU 1060 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 1 Step 1 Icon Screw (quantity) Color M2 × 17 mm, flat-head, nylon-coated Black (1) Torque 0.196 Nm (2.0 kgfcm) Lift the keyboard a little in the direction shown by arrow 2 , and then detach the connector 3 .
Removing and replacing a FRU When installing: Make sure that the keyboard edges a are under the frame as shown in this figure.
Removing and replacing a FRU 1070 Mini PCI adapter for wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 In steps 2a and 2b , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159), or pick the connectors with your fingers and gently unplug them in the direction shown by the arrow. 3 1 2a 2b 1 When installing: 1.
Removing and replacing a FRU 1080 Modem daughter card (MDC-1.5) For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 1 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.0 kgfcm) In step 2 , remove the card by pulling the tab with your fingers in the direction shown by the arrow.
Removing and replacing a FRU Turn the card over 3 , and detach the modem connector 4 . 3 4 When installing: Make sure that the modem connector and the connector on the underside of the card are attached firmly.
Removing and replacing a FRU 1090 PCI Express Mini card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 In step 1a or 1b , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Removing and replacing a FRU 3 When installing: Plug the red cable into the jack labeled MAIN on the card, and the blue cable into the jack labeled DIV.
Removing and replacing a FRU 1100 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 2 1 When installing: Make sure that the battery connector is attached firmly.
Removing and replacing a FRU 1110 Wireless WAN antenna cable (DIV) For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1090 PCI Express Mini card for wireless WAN” on page 71 In step 1 , strip off the tapes securing the antenna cable. 1 1 1 2 3 1 74 Step Screw (quantity) Color Torque 2 M2 × 3 mm, flat-head, nylon-coated (1) Black 0.196 Nm (2.
Removing and replacing a FRU When installing: Make sure that the cable is routed along the cable guides a , and that secured with tapes b .
Removing and replacing a FRU 1120 Keyboard bezel and speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 1 1 Step Screw (quantity) Color Torque 1 M2 × 17 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.
Removing and replacing a FRU 4 4 2 3 Strip the tape that secures the cable 2 , and disconnect the speaker cable 3 . Step Screw (quantity) Color Torque 5 M2 × 3 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.
Removing and replacing a FRU 6 7 6 6 6 8 8 9 Step Screw (quantity) Color Torque 6 M2 × 3 mm, flat-head, nylon-coated (4) Black 0.196 Nm (2.0 kgfcm) When installing: Make sure that the speaker cables are routed along the cable guides, and that the connector is attached firmly.
Removing and replacing a FRU 1130 Fan assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1120 Keyboard bezel and speaker assembly” on page 76 1 1 1 1 1 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (6) Black 0.196 Nm (2.
Removing and replacing a FRU 3 80 MT 2529, 2530, 2531, and 2532 2
Removing and replacing a FRU When installing: v Before you attach the fan assembly to the computer, apply thermal grease on the part marked a as in the following figure. a v Make sure that the fan connector is attached firmly.
Removing and replacing a FRU v When attaching the fan assembly to the frame, take care not to damage the heat sink ( b ) of the fan assembly.
Removing and replacing a FRU 1140 CPU For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1120 Keyboard bezel and speaker assembly” on page 76 v “1130 Fan assembly” on page 79 Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Rotate the head of the screw in the direction shown by arrow 1 to release the lock; then remove the CPU 2 .
Removing and replacing a FRU 1150 LCD assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1090 PCI Express Mini card for wireless WAN” on page 71 v “1120 Keyboard bezel and speaker assembly” on page 76 2 1 Step Screw (quantity) Color Torque 1 M2 × 5 mm, flat-head, nylon-coated (1) Black 0.196 Nm (2.
Removing and replacing a FRU 4 3 3 4 5 6 Step Screw (quantity) Color Torque 3 M2 × 5 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.0 kgfcm) 4 M2 × 5 mm, flat-head, nylon-coated (2) Black 0.296 Nm (3.0 kgfcm) In step 6 , release the antenna cables from the cable guides. Notes: 1. Route the antenna cables along the cable guides. When you route the cables, do not tense them. To do so, the cables may get damaged by the cable guides of the frame, and may cause a broken wire. 2.
Removing and replacing a FRU 7 7 86 MT 2529, 2530, 2531, and 2532
Removing and replacing a FRU 1160 Base cover For access, remove these FRUs, in order: v “1010 Battery pack” on page 57 v “1020 Ultrabay Enhanced device” on page 59 v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails” on page 60 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1080 Modem daughter card (MDC-1.
Removing and replacing a FRU Attention: Before step 3 , be sure that the Ultrabay Enhanced device eject lever is not popped out and it is housed in its position properly as shown in the figure a .
Removing and replacing a FRU Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: a Windows license label (COA) b FCC label c Product label d FCC or homologation label For some models, you also need to apply one or two FCC labels c .
Removing and replacing a FRU 1170 3-1 Digital Media Reader sub card with cable For access, remove these FRUs, in order: v “1010 Battery pack” on page 57 v “1020 Ultrabay Enhanced device” on page 59 v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails” on page 60 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1090 PCI Express Mini card for wireless WAN” on page 71 v “1120 Key
Removing and replacing a FRU 4 3 Step Screw (quantity) Color Torque 3 M2 × 3 mm, flat-head, nylon-coated (1) Black 0.196 Nm (2.
Removing and replacing a FRU 1180 USB sub card with cable For access, remove these FRUs, in order: v “1010 Battery pack” on page 57 v “1020 Ultrabay Enhanced device” on page 59 v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails” on page 60 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1090 PCI Express Mini card for wireless WAN” on page 71 v “1120 Keyboard bezel and speak
Removing and replacing a FRU 3 3 4 2 Step Screw (quantity) Color Torque 3 M2 × 5 mm, flat-head, nylon-coated (2) Black 0.196 Nm (2.
Removing and replacing a FRU 1190 MG (magnesium) frame For access, remove these FRUs, in order: v “1010 Battery pack” on page 57 v “1020 Ultrabay Enhanced device” on page 59 v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails” on page 60 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1080 Modem daughter card (MDC-1.
Removing and replacing a FRU Remove the ac power jack cable a and the modem cable b . 4 3 2 1 5 When installing: Make sure the connectors are attached firmly, and that the cables are routed as in the figure above.
Removing and replacing a FRU Remove the CPU support plate ( c ). 6 6 c Step Screw (quantity) Color Torque 6 M2 × 5 mm, flat-head, nylon-coated (4) Black 0.196 Nm (2.
Removing and replacing a FRU 8 8 7 7 7 7 7 8 7 9 Step Screw (quantity) Color Torque 7 M2 × 5 mm, flat-head, nylon-coated (6) Black 0.196 Nm (2.0 kgfcm) 8 M2 × 9 mm, flat-head, nylon-coated (3) Black 0.196 Nm (2.0 kgfcm) In step 9 , loosen the hex screws.
Removing and replacing a FRU Remove the system board and the PC Card/ExpressCard slots assembly from the MG frame together, in the direction shown by arrow 10 .
Removing and replacing a FRU 1200 System board and PC Card/ExpressCard slots assembly For access, remove these FRUs, in order: v “1010 Battery pack” on page 57 v “1020 Ultrabay Enhanced device” on page 59 v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails” on page 60 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1050 DIMM” on page 65 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1080 Modem daughter card (MDC-1.
Removing and replacing a FRU Important notice for handling the system board When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.
Removing and replacing a FRU Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling.
Removing and replacing a FRU 1 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (2) Silver 0.196 Nm (2.0 kgfcm) Turn over the system board, and then disconnect the PC Card/ExpressCard slots assembly from the system board. 2 When installing: Make sure that the connector of PC Card/ExpressCard slots assembly is attached to the system board firmly.
Removing and replacing a FRU 2010 LCD front bezel For access, remove this FRU: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1090 PCI Express Mini card for wireless WAN” on page 71 v “1120 Keyboard bezel and speaker assembly” on page 76 v “1150 LCD assembly” on page 84 v “2010 LCD front bezel” 1 1 1 Step Screw cap 1 Screw (quantity) Color Torque M2 × 5 mm, f
Removing and replacing a FRU In step 3 , while sliding the LCD latch lever in the direction shown by the arrow, remove the bezel in the direction shown by arrow 4 .
Removing and replacing a FRU 2020 Inverter card For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1090 PCI Express Mini card for wireless WAN” on page 71 v “1120 Keyboard bezel and speaker assembly” on page 76 v “1150 LCD assembly” on page 84 v “2010 LCD front bezel” on page 103 1 2 3 When installing: Make sure that connectors 2
Removing and replacing a FRU 2030 Bluetooth daughter card (BDC-2) For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1090 PCI Express Mini card for wireless WAN” on page 71 v “1120 Keyboard bezel and speaker assembly” on page 76 v “1150 LCD assembly” on page 84 v “2010 LCD front bezel” on page 103 1 2 3 106 Step Screw (quantity)
Removing and replacing a FRU When installing: Make sure that connector is attached firmly, and that the card is attached to the guide as in this figure.
Removing and replacing a FRU 2040 Wireless WAN antenna cable (MAIN) For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1090 PCI Express Mini card for wireless WAN” on page 71 v “1120 Keyboard bezel and speaker assembly” on page 76 v “1150 LCD assembly” on page 84 v “2010 LCD front bezel” on page 103 v “2020 Inverter card” on page 105
Removing and replacing a FRU When installing: In step 2 , press the part indicated by the arrow until it snaps into place. 1 1 3 2 4 Note: In step 4 , do not tense the cable. To do so, the cable may get damaged by the hinge, and may cause a broken wire.
Removing and replacing a FRU Cable routing: Route the antenna cable as shown in this figure.
Removing and replacing a FRU 2050 LCD panel, LCD cable, and hinges For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1090 PCI Express Mini card for wireless WAN” on page 71 v “1120 Keyboard bezel and speaker assembly” on page 76 v “1150 LCD assembly” on page 84 v “2010 LCD front bezel” on page 103 v “2020 Inverter card” on page 105 v
Removing and replacing a FRU 3a 3b 6 5 4 (continued) 112 MT 2529, 2530, 2531, and 2532
Removing and replacing a FRU Remove the hinges ( a ) from the LCD panel. a 7 7 8 a 8 7 7 Step Screw (quantity) Color Torque 7 M2 × 3 mm, small-head, nylon-coated (4) Silver 0.196 Nm (2.0 kgfcm) Remove the LCD cable assembly ( b ) from the LCD panel. 9 b 10 When installing: When replacing any LCD FRUs, be sure not to pinch the antenna cables. Make sure that the cables are routed as shown in the figures on page 117 and 118.
Removing and replacing a FRU 2060 LCD rear cover and wireless LAN antenna cables For access, remove these FRUs in order: v “1010 Battery pack” on page 57 v “1040 Palm rest or palm rest with fingerprint reader” on page 63 v “1060 Keyboard” on page 66 v “1070 Mini PCI adapter for wireless LAN” on page 68 v “1090 PCI Express Mini card for wireless WAN” on page 71 v “1120 Keyboard bezel and speaker assembly” on page 76 v “1150 LCD assembly” on page 84 v “2010 LCD front bezel” on page 103 v “2020 Inverter card”
Removing and replacing a FRU 3 When installing: Attache the latches as shown in this figure.
Removing and replacing a FRU 5 5 4 116 MT 2529, 2530, 2531, and 2532 4 4 4
Removing and replacing a FRU Cable routing: Route the antenna cables as shown in the following figures.
Removing and replacing a FRU Wireless LAN antenna cable (AUX: black) a 118 MT 2529, 2530, 2531, and 2532
Locations Locations Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ThinkLight Status indicators Note: For the description of each indicator, see “Status indicators” on page 37.
Locations Rear view 1 2 3 4 5 6 7 8 9 10 11 Status indicators Note: For the description of each indicator, see “Status indicators” on page 37.
Locations Bottom view 1 2 3 4 5 6 7 8 9 Battery pack Battery pack latch Docking connector Infrared port Wireless raido switch LCD cover latch 3-1 Digital Media Reader status indicator 3-1 Digital Media Reader Hard disk drive 1 2 9 3 8 7 6 5 4 ThinkPad Z60m 121
Parts list Parts list v Each FRU is available for all types or models, unless specific types or models are specified. v A CRU (customer replaceable unit) is identified by a single asterisk (*) or two asterisks (**) in the CRU ID column. An N in the CRU ID column means the part is not a CRU. A single asterisk (*) means the part is a Tier 1 CRU; two asterisks (**) means the part is a Tier 2 CRU. v FRUs marked with OP are available as options. v FRUs marked with R are RoHS compliant.
Parts list Overall 1 25 24 2 23 3 c a 22 21 4 5 6 7 20 8 19 9 10 18 11 12 17 b 13 14 16 15 ThinkPad Z60m 123
Parts list No. FRU a-c See “Miscellaneous parts” on page 153. CRU ID 1 LCD unit (see “LCD FRUs” on page 143.) 2 Keyboard bezel assembly 26R9588 N 3 Speaker assembly 39T7221 N 4 Modem daughter card (MDC-1.
Parts list No.
Parts list No.
Parts list No.
Parts list No.
Parts list No.
Parts list No.
Parts list No. 12 FRU P/N CRU ID Hard disk drive, 80 GB, 9.
Parts list No.
Parts list No. 14 FRU P/N CRU ID CD-ROM drive, 12.7 mm, TEAC (CD-244EN) v 2529-CTO v 2530-CTO v 2530-JQx v 2531-CTO v 2532-CTO 39T2661 * MKE (SR-8178) 39T2663 * HLDS (GDR-8084N) 39T2665 * DVD drive, 12.7 mm v 2529-CTO, E4x, E5x v 2530-CTO, 1Yx, 1Zx, E4x v 2530-JPx v 2531-CTO v 2532-CTO DVD/CD-RW combo drive, 12.
Parts list No. 14 FRU P/N CRU ID DVD-RAM/RW drive, 12.7 mm v 2529-H1x, H3x, H4x, H5x, H7x. H8x, H9x, HAx, HBx, HCx, HDx, HEx, HFx, HGx, HHx, HJx, HKx, HLx, HNx, HPx, HQx, HRx, HUx, HWx, HSx, HTx, R3x, R5x, R8x, RCx v 2530-J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x, JBx, JDx, JE,x JFx, JGx, JHx, JKx, JLx.
Parts list No.
Parts list No.
Parts list No. 18 FRU P/N CRU ID System board assembly with 915PM, M22-64 v 2529-CTO, 1Hx, E7x, E8x, F8x, F9x, FAx, FBx, FCx, FEx, FFx, FMx, FPx, FQx, FRx, FSx, G6x, G7x, G8x, G9x v 2529-H1x, H7x, H8x, HDx, HEx, HFx, HTx, L2x, P3x, R9x, RAx v 2530-CTO, 11x, 1Gx, 1Hx, 1Jx, 1Kx, 1Mx, 1Nx, 2Bx, 2Cx, 2Ex, 34x, 39x, 3Dx, 3Ex, 3Jx, 3Mx, 42x, 47x, 48x, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 55x, 56x, 5Ax, 5Bx v 2530-J3x, J4x, JTx, JVx, K1x, K2x, K3x, K4x, L2x, L4x.
Parts list No. 20 FRU P/N CRU ID CPU assembly, Intel Celeron M processor 370 (1.5 GHz) v 2529-CTO, F3x, F4x, FRx v 2529-H6x, P1x v 2530-CTO, 18x, 1Dx, 1Ex, 2Dx, 3Bx, 52x v 2530-J9x, JAx, JBx, JDx, JEx, JFx, JGx, JHx, JKx, JLx, JMx, JNx, JPx, JQx, K8x, K9x, KAx, KBx, LBx, LCx. LDx v 2531-CTO v 2532-CTO 39T0331 N CPU assembly, Intel Celeron M processor 380 (1.
Parts list No. 20 FRU P/N CRU ID CPU assembly, Intel Pentium M processor 750 (1.
Parts list No.
Parts list No.
Parts list No.
Parts list LCD FRUs 1 10 2 9 8 3 4 7 5 a b c d e 6 ThinkPad Z60m 143
Parts list No. FRU a-d See “Miscellaneous parts” on page 153. CRU ID 41V9410 N 1 LCD front bezel 2 LCD panel, 15.4-in.
Parts list No. FRU P/N CRU ID 2 LCD panel, 15.4-in.
Parts list No.
Parts list No. 5 FRU P/N LCD cover kit (black) 41V9793 v 2529-CTO, E1x, E2x, E3x, E4x, E5x, E6x, E7x, E8x, F1x, F2x, F3x, F4x, F5x, F6x, F7x, F8x, F9x, FFx, FMx, FPx, FQx, FRx, FSx, G1x, G2x, G3x, G4x, G5x, G6x, G7x, G8x, G9x v 2529-H2x, H3x, H5x, H6x, H7x, H8x, HAx, HBx, HCx, HMx, HNx, HPx.
Parts list No.
Parts list Keyboard Language P/N (NMB) P/N (ALPS) P/N (Chicony) CRU ID Arabic 39T0961 39T7121 39T7181 ** Belgian 39T0962 39T7122 39T7182 Canadian, multilanguage (445) 39T0959 39T7119 39T7179 Chinese, Traditional 39T0985 39T7145 39T7205 Czech 39T0963 39T7123 39T7183 Danish 39T0964 39T7124 39T7184 Dutch 39T0972 39T7132 39T7192 English, U.K. 39T0982 39T7142 39T7202 English, U.S. 39T0958 39T7118 39T7178 English, U.S.
Parts list Recovery CDs Windows XP Professional Windows XP Professional is preinstalled as the operating system in the following models: v 2529-CTO, E1x, E2x, E3x, E5x, E6x, E7x, E8x, E9x, EAx, F2x, F4x, F6x, F7x, F8x, FAx, FCx, FFx, FGx, FKx, FLx, FMx, FPx, Fx v 2529-H1x, H3x, H4x, H5x, H8x, H9x, HCx, HGx, HJx, HPx, HQx, HRx, HUx, HWx, R2x, R3x, R5x, R6x, R7x, R8x, R9x, RAx, RBx, RCx v 2530-CTO, 11x, 13x, 18x, 19x, 1Fx, 1Kx, 1Nx, 21x, 25x, 26x, 27x, 28x, 2Ax, 2Bx, 2Cx, 2Ex, 34x, 35x, 36x, 37x, 38x, 39x, 3
Parts list Language P/N CRU ID Arabic 42J5258 * Chinese, Simplified 42J5251 Chinese, Traditional 42J5252 Chinese, Traditional (Hong Kong S.A.R.) 42J5253 Czech 42J5257 Danish 42J5247 Dutch 42J5250 English, Russia 42J5240 English, U.K. 42J5239 English, U.S.
Parts list Windows XP Home Edition Windows XP Home Edition is preinstalled as the operating system in the following models: v 2529-CTO, 1Hx, E4x, EBx, F1x, F3x, F5x, F9x, FBx, FEx, FHx, FJx, FQx, FRx, FTx v 2529-H2x, H6x, H7x, HAx, HBx, HDx, HEx, HFx, HHx, HKx, HLx, HMx, HNx, HSx, HTx v 2530-CTO, 14x, 16x, 1Cx, 1Dx, 1Ex, 1Gx, 1Hx, 1Jx, 1Mx, 1Yx, 1Zx, 22x, 23x, 24x, 29x, 2Dx, 2Gx, 2Hx, 31x, 32x, 33x, 3Bx, 47x, 4Ax, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx, E4x, EBx v 2530-J5x, J6x, J7x, J8x, JEx, JFx, JKx, JLx, JMx, JNx, JP
Parts list Miscellaneous parts FRU P/N CRU ID Screw kit (including nylon-coated screws): v M2 × 3 mm-I (BNI, NYLOK) (25) v M2 × 5 mm-I (BNI, NYLOK) (31) v M2 × 5 mm-F (BNI, NYLOK) (2) v M2 × 9 mm-I (BNI, NYLOK) (5) v M2 × 17 mm-I (BNI, NYLOK) (7) v M3 × 4 mm-P (BNI, NYLOK) (1) v M3 × 2.8 mm-I (BNI, D6.2, T2.
Parts list AC adapters FRU P/N CRU ID 3-pin (90 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxV) OP ASTEC 92P1104 * Lite-On 92P1108 * Sanken 92P1112 * 2-pin (90W, 20 V) slim adapter for non-PFC model (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY) OP ASTEC 92P1106 * Lite-On 92P1110 * Sanken 92P1114 * Common parts list Tools Tool P/N Screwdriver kit 95F3598 1/4" drive spinner handle 1650840 1/4" Sq.
Parts list Power cords (system) A ThinkPad power cord for a specific country or region is usually available only in that country or region: For 2-pin power cords: Region P/N CRU ID Canada, U.S.
Notices Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Notices estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Part Number: 39T6195_01 (1P) P/N: 39T6195_01
