ThinkPad SL300 Hardware Maintenance Manual
ThinkPad SL300 Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 143. Forth Edition (March 2009) © Copyright Lenovo 2008, 2009. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual . . . . . . . . . . v Safety information . . . . . . . . . . 1 General safety . . . . . . . . . . . . . . 2 Electrical safety . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . 5 Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . . . . 6 Grounding requirements . . . . . . . . . . 6 Safety notices: multilingual translations . . . . . 7 Laser compliance statement . . . . . . . . . 14 Important service information . . . . .
Common service tools . . . . . . . . . 141 Notices . . . . . . . . . . . . . . 143 iv ThinkPad SL300 Hardware Maintenance Manual Trademarks . . . . . . . . . . . . . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad SL300 MT 2738 Use this manual along with the advanced diagnostic tests to troubleshoot problems. The manual is divided into sections as follows: v The common sections provide general information, guidelines, and safety information required in servicing computers. v The product-specific section includes service, reference, and product-specific parts information.
vi ThinkPad SL300 Hardware Maintenance Manual
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad computer.
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium.
Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau. Ne la mettez pas en court-circuit.
Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium.
Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des symptômes persistent après le lavage.
Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Safety notice 8 DANGER Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Laser compliance statement Some models of ThinkPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
16 ThinkPad SL300 Hardware Maintenance Manual
Important service information This chapter presents following important service information: v “Strategy for replacing FRUs” – “Strategy for replacing a hard disk drive” on page 18 – “Important notice for replacing a system board” on page 18 – “How to use error message” on page 18 v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 19 – “Product definition” on page 19 – “FRU identification for CTO, CMV, and GAV products” on page 19 v “Important information about replacing RoHS compliant FRUs” on p
v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one. v If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.
Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
22 ThinkPad SL300 Hardware Maintenance Manual
General checkout This chapter presents following information: v “What to do first” on page 24 v “Checkout guide” on page 25 – “Diagnostics using PC-Doctor for DOS” on page 26 – “PC-Doctor for Windows” on page 28 – “PC-Doctor for Rescue and Recovery” on page 28 v “Power system checkout” on page 29 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to your particular computer.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of servicer __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Diagnostics using PC-Doctor for DOS The ThinkPad computer has a test program called PC-Doctor for DOS (hereafter called PC-Doctor.) You can detect errors by running the diagnostics test included in PC-Doctor. This section is an overview of the procedure. For details that depend on model-unique functions, refer to “ThinkPad SL300” on page 49. Note: PC-Doctor for DOS is available at following Web site: http://www.lenovo.
Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names may appear in the PC-Doctor menu. Diagnostics Interactive Tests Hardware Info Utility Quit F1=Help Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Serial Ports Parallel Ports Fixed Disks Diskette Drives Other Devices Communication Wireless LAN PM Memory PC-DOCTOR 2.0 Copyright 2008 PC-Doctor, Inc. All Rights Reserved. Use the cursor keys and ESC to move in menus.
Detecting system information with PC-Doctor PC-Doctor can detect the following system information: Hardware Info v System Configuration v Memory Contents v Physical Disk Drives v Logical Disk Drives v VGA Information v IDE Drive Info v PCI Information v PNPISA Info v SMBIOS Info v VESA LCD Info v Hardware Events Log Utility v v v v v v v v v v v Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick
Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 63). 4. Remove the backup battery (see “1160 Backup battery” on page 86). 5. Measure the voltage of the backup battery. See the following figure. Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board.
32 ThinkPad SL300 Hardware Maintenance Manual
Related service information This chapter presents following information: v “Restoring the factory contents by using Product Recovery discs” v “Passwords” on page 34 v “Power management” on page 37 v “Symptom-to-FRU index” on page 39 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
8. When the recovery process is complete, the Welcome to Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup. Passwords As many as three passwords may be needed for any ThinkPad computer: the power-on password (POP), the hard-disk password (HDP), and the supervisor password (SVP). If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.
How to remove the power-on password To remove a POP that you have forgotten, do the following: (A) If no SVP has been set: 1. Turn off the computer. 2. Remove the battery pack. For how to remove the battery pack, see “1010 Battery pack” on page 63. 3. Remove the backup battery. For how to remove the backup battery, see “1160 Backup battery” on page 86. 4. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does not appear. The POP has been removed. 5.
6. Select Change HDD Master Password by using the cursor directional keys. 7. Type the current master HDP in the Enter CURRENT Password field. then leave the Enter New Password field blank, and press Enter twice. 8. Press F10. 9. Select OK in the Setup Configuration window. Both user HDP and master HDP will have been removed.
Power management To reduce power consumption, the computer has three power management modes: screen blank, standby, and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, press Fn+F3. To end screen blank mode and resume normal operation, press any key.
v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters standby mode. Wait a few seconds before taking any action to reenter operation mode. Hibernation mode In hibernation mode, the following occurs: v The system status, RAM, VRAM, and setup data are stored on the hard disk. v The system is powered off.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 44 v “Beep symptoms” on page 45 v “No-beep symptoms” on page 45 v “LCD-related symptoms” on page 46 v “Intermittent problems” on page 47 v “Undetermined problems” on page 47 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 1. Numeric error codes (continued) 40 Symptom or error FRU or action, in sequence 7001 (HDCP) Memory is not enough for HDCP Key Provisioning! Add the DIMMs. 7002 (HDCP) Failed to check the key set Family-EKS! System board. 7003 (HDCP) Chip-Unique-EKS re-encryption failed! System board. 7004 (HDCP) Failed to check the key set Chip-Unique-EKS! System board. 7005 (HDCP) Cipher Initialization with Chip-Unique-EKS failed! System board. 8100 Gate20 Error 1. System board. 2. DIMM.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 8318 S.M.A.R.T. Capable but Command Failed 1. Hard disk drive. 2. System board. 3. SATA cable. 8319 S.M.A.R.T. Command Failed 1. Hard disk drive. 2. System board. 3. SATA cable. 831A S.M.A.R.T. Status BAD, Backup and Replace 1. Hard disk drive. 2. System board. 3. SATA cable. 831B S.M.A.R.T. Capable and Status BAD 1. Hard disk drive. 2. System board. 3. SATA cable.
Table 1. Numeric error codes (continued) 42 Symptom or error FRU or action, in sequence 850D PCI IRQ routing table error Update the BIOS. 850E Timer Error System board. 850F Refresh timer test failed System board. 8510 Interrupt Controller-1 error System board. 8511 Interrupt Controller-2 error System board. 8600 CMOS Date/Time Not Set Run BIOS Setup Utility and save it. If the same error happens after doing it, replace the system board. 8601 CMOS Battery Low 1. Backup battery. 2.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 870A Unknown BIOS error. Error code = 004Bh Update the BIOS. 870B Floppy Controller Failure 1. External floppy disk drive. 2. System board. 8800 Warning! Unsupported USB device found and disabled! Remove unsupported USB devices. 8801 Warning! Port 60h/64h emulation is not supported by this USB Host Controller! If possible, change the setting. 8802 Warning! EHCI controller disabled.
Error messages Table 2. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Beep symptoms Table 3. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 39. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2. System board.
LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. The LCD should be replaced if the number of missing, discolored, or lighted dots in any background is as follows: Table 5.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
48 ThinkPad SL300 Hardware Maintenance Manual
ThinkPad SL300 This chapter presents following product-specific service references and product-specific parts information. v “Specifications” v “Status indicators” on page 52 v “FRU tests” on page 54 v “Fn key combinations” on page 56 v “FRU replacement notices” on page 58 v “Removing and replacing a FRU” on page 62 v “Locations” on page 112 v “Parts list” on page 115 Specifications The following table lists the specifications of the ThinkPad SL300 : Table 7.
Table 7. Specifications (continued) Feature Description Standard memory v v v v v Optional memory v 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card v 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card v 2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card (maximum of 4.
Table 7. Specifications (continued) Feature Description Battery v Li-ion battery (4 cells) 2.6 Ah v Li-ion battery (6 cells) 2.4 Ah v Li-ion battery (9 cells) 2.
Status indicators The system status indicators show the status of the computer, as follows: 1 10 9 2 8 7 5 6 4 3 Table 8. Status indicators 52 Indicator Meaning 1 Power on The computer is on and ready to use. The power switch stays lit whenever the computer is on and is not lit when the computer is in sleep (standby) mode. 2 Device access A hard disk drive is being used to read or write data.
Table 8. Status indicators (continued) Indicator Meaning 6 Sleep (standby Green: The computer is in sleep (standby) mode. in Windows XP) Blinking green: status The computer is entering sleep (standby) mode or hibernation mode, or is resuming normal operation. 7 Battery status Green: The battery has more than 20% charge. Orange: The battery has between 5% and 20% charge. Blinking orange (rapid): The battery has less than 5% charge. Note: The battery may be charging.
FRU tests The following table shows the test for each FRU. Table 9. FRU tests 54 FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard Power Diagnostics --> ThinkPad Devices --> AC Adapter, Battery 1 (Battery2) LCD unit 1. Diagnostics --> Video Adapter 2. Interactive Tests --> Video Modem daughter card (MDC-1.5) 1. Make sure the modem is set up correctly. 2.
Table 9. FRU tests (continued) FRU Applicable test TrackPoint or pointing If the TrackPoint does not work, check the configuration as device specified in the BIOS Setup Utility. If the TrackPoint is disabled, select Automatic to enable it. After you use the TrackPoint, the pointer may drift on the screen for a short time. This drift can occur when a slight, steady pressure is applied to the TrackPoint pointer. This symptom is not a hardware problem.
Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 10. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock your computer. Fn+F3 Select a power scheme that has been created by Power Manager. When you press this combination, a panel for selecting a power scheme appears. Notes: 1. To use the Fn+F3 key combination, you must have the ThinkPad PM device driver installed on the computer. 2.
Table 10. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings. Switch a display output location v External monitor (CRT display) v Computer display and external monitor (LCD + CRT display) v Computer display (LCD) Notes: 1.
FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 61 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number. When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the LENOVO ThinkPad SL Series Maintenance Diskette Version 1.01 or later, and restart the computer. 2. From the main menu, select 2. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
Reading or writing the ECA information Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board. The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application.
Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 58. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page.
1010 Battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Table 11. Removal steps of battery pack Unlock the battery release lever 1 . Holding the battery release lever in the unlocked position 2 , remove the battery pack in the direction shown by arrow 3 . 1 2 3 When installing: Install the battery pack along the slide rails of the slot. Then make sure that the battery release lever is in the locked position.
1020 Optical drive For access, remove this FRU: v “1010 Battery pack” on page 63 Table 12. Removal steps of optical drive 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.
1030 Hard disk drive (HDD) cover and HDD For access, remove this FRU: v “1010 Battery pack” on page 63 Attention: v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible. v Never remove the drive while the system is operating or is in suspend mode. Table 13.
Table 13. Removal steps of HDD cover and HDD (continued) 3 When installing: Make sure that the HDD connector is attached firmly.
1040 DIMM slot cover For access, remove this FRU: v “1010 Battery pack” on page 63 Table 14. Removal steps of DIMM slot cover Note: Loosen the screws 1 , but do not remove them.
1050 DIMM For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 DIMM slot cover” on page 67 Table 15. Removal steps of DIMM 1 1 2 Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a : lower slot), but not in SLOT-1 ( b : upper slot). b a When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place.
1060 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 DIMM slot cover” on page 67 Table 16. Removal steps of PCI Express Mini Card (full size) for wireless WAN In step 1a and 1b , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 16. Removal steps of PCI Express Mini Card (full size) for wireless WAN (continued) 3 When installing: Plug the black cable with red label into the jack labeled MAIN, and the black cable with blue label into the jack labeled AUX on the card.
1070 Intel Turbo Memory Minicard For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 DIMM slot cover” on page 67 Table 17. Removal steps of Intel Turbo Memory Minicard 1 1 Step Screw (quantity) 1 For Japan M2 × 3 mm, tamper proof (2) Color Torque Black 0.189 Nm (1.85 kgfcm) Black 0.189 Nm (1.
1080 Thermal door For access, remove this FRU: v “1010 Battery pack” on page 63 Table 18. Removal steps of thermal door Note: Loosen the screws 2 , but do not remove them.
1090 Fan assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1080 Thermal door” on page 72 Table 19. Removal steps of fan assembly 3 3 4 4 2 1 2 Step Screw (quantity) Color Torque 2 M2 × 4 mm, wafter-head, nylon-coated (2) Silver 0.167 Nm (1.7 kgfcm) 3 M2 × 3 mm, wafter-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) Note: Loosen the screws 4 , but do not remove them. Attention: Do not handle the fan roughly.
Table 19. Removal steps of fan assembly (continued) 5 6 Table 20. Installation of the fan assembly When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. For the new fan assembly, you need to peel the thin film off from the rubber b .
1100 CPU thermal module For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1080 Thermal door” on page 72 v “1090 Fan assembly” on page 73 Table 21. Removal steps of CPU thermal module 4 2 1 3 Step Screw (quantity) Color Torque 1 to 4 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.167 Nm (1.7 kgfcm) Attention: Do not handle the CPU thermal module roughly. Improper handling of the module can cause distortion or deformation and imperfect contact with components.
Table 21. Removal steps of CPU thermal module (continued) 5 6 Table 22. Installation of the CPU thermal module When installing: v Before you attach the CPU thermal module to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. a v Make sure that the fan connector is attached firmly.
1110 CPU For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1080 Thermal door” on page 72 v “1090 Fan assembly” on page 73 v “1100 CPU thermal module” on page 75 Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Table 23. Removal steps of CPU Rotate the head of the screw in the direction shown by arrow 1 to release the lock; then remove the CPU.
1120 Palm rest For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU. If the fingerprint reader has any defects, you can replace it by the procedures given in this section, which are the same for a palm rest with or without a fingerprint reader. Table 24.
Table 24. Removal steps of palm rest (continued) 3 3 3 4 3 4 Step Icon Screw (quantity) Color Torque 3 M2 × 9 mm, wafer-head, nylon-coated (4) Black 0.167 Nm (1.7 kgfcm) 4 M2 × 8 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.
Table 24.
1130 Bluetooth daughter card (BDC) For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1120 Palm rest” on page 78 Table 25. Removal steps of BDC 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) When installing: Make sure that connector is attached firmly.
1140 PCI Express Mini Card for wireless LAN/WiMAX For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1120 Palm rest” on page 78 Table 26. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 26.
1150 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1120 Palm rest” on page 78 Table 27. Removal steps of keyboard 1 Step Icon 1 Screw (quantity) Color Torque M2 × 16 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 2 3 4 84 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.
Table 27. Removal steps of keyboard (continued) 6 6 6 7 7 6 5 When installing: Make sure that the connectors are attached firmly.
1160 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1120 Palm rest” on page 78 Table 28. Removal steps of backup battery 1 2 When installing: Make sure that the battery connector is attached firmly.
1170 Top case sub assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1120 Palm rest” on page 78 v “1150 Keyboard” on page 84 Table 29. Removal steps of top case sub assembly 3 3 3 3 3 4 4 2 1 1 5 Step Screw (quantity) Color Torque 1 M2 × 4 mm, wafer-head, nylon-coated (2) Silver 0.167 Nm (1.7 kgfcm) 2 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.
Table 29. Removal steps of top case sub assembly (continued) 8 8 9 8 8 9 6 7 9 9 Step Screw (quantity) Color Torque 6 M2 × 2 mm, wafer-head, nylon-coated (1) Silver 0.167 Nm (1.7 kgfcm) 7 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) When installing: Make sure that all the claws are attached firmly.
1180 Magnesium frame assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1120 Palm rest” on page 78 v “1150 Keyboard” on page 84 v “1170 Top case sub assembly” on page 87 Table 30. Removal steps of magnesium frame assembly 1 2 5 1 3 5 4 3 Step Screw (quantity) Color Torque 1 M2 × 5 mm, wafer-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) 2 M2 × 8 mm, wafer-head, nylon-coated (1) Black 0.
1190 I/O board For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1120 Palm rest” on page 78 v “1150 Keyboard” on page 84 v “1170 Top case sub assembly” on page 87 v “1180 Magnesium frame assembly” on page 89 Table 31.
Table 31. Removal steps of I/O board (continued) 5 5 5 5 6 7 Step Screw (quantity) Color Torque 5 M2 × 4 mm, wafer-head, nylon-coated (4) Silver 0.167 Nm (1.
1200 LCD unit For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1040 DIMM slot cover” on page 67 v “1060 PCI Express Mini Card for wireless WAN” on page 69 v “1120 Palm rest” on page 78 v “1140 PCI Express Mini Card for wireless LAN/WiMAX” on page 82 v “1150 Keyboard” on page 84 v “1170 Top case sub assembly” on page 87 Table 32.
Table 32. Removal steps of LCD unit (continued) 3 Step Screw (quantity) Color Torque 3 M2 × 5 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.
Table 32. Removal steps of LCD unit (continued) In step 4 , remove the tapes securing the antenna cables, and release the cables from the cable guides of the base cover 5 .
Table 32. Removal steps of LCD unit (continued) 7 7 When installing: 1. Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. 2. Make sure that the LCD connector is attached firmly.
1210 System board Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.
For access, remove these FRUs, in order: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1040 DIMM slot cover” on page 67 v “1050 DIMM” on page 68 v “1060 PCI Express Mini Card for wireless WAN” on page 69 v “1070 Intel Turbo Memory Minicard” on page 71 v “1080 Thermal door” on page 72 v “1090 Fan assembly” on page 73 v “1100 CPU thermal module” on page 75 v “1110 CPU” on page 77 v “1120 Palm rest” on page 78 v “1130 Bluetooth dau
Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling.
Table 33. Removal steps of system board 1 2 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 2 Hex stud, spring washer (2) Silver 0.
Table 33. Removal steps of system board (continued) 3 5 4 3 3 3 Step Screw (quantity) Color Torque 3 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.167 Nm (1.7 kgfcm) 5 M2 × 9mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 6 When installing: Make sure that the connector is attached firmly.
1220 Small board For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1040 DIMM slot cover” on page 67 v “1050 DIMM” on page 68 v “1060 PCI Express Mini Card for wireless WAN” on page 69 v “1070 Intel Turbo Memory Minicard” on page 71 v “1080 Thermal door” on page 72 v “1090 Fan assembly” on page 73 v “1100 CPU thermal module” on page 75 v “1110 CPU” on page 77 v “1120 Palm rest” on page 78 v “11
1230 Base cover For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1040 DIMM slot cover” on page 67 v “1050 DIMM” on page 68 v “1060 PCI Express Mini Card for wireless WAN” on page 69 v “1070 Intel Turbo Memory Minicard” on page 71 v “1080 Thermal door” on page 72 v “1090 Fan assembly” on page 73 v “1100 CPU thermal module” on page 75 v “1110 CPU” on page 77 v “1120 Palm rest” on page 78 v “113
2010 LCD front bezel For access, remove this FRU: v “1010 Battery pack” on page 63 Table 36. Removal steps of LCD front bezel 1 1 1 1 Step Screw cap Screw (quantity) M2 × 4 mm, bind-head, nylon-coated (4) 1 Color Torque Silver 0.167 Nm (1.
2020 Integrated camera For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “2010 LCD front bezel” on page 103 Note: Some models do not have the integrated camera. Table 37. Removal steps of integrated camera 3 2 1 When installing: Make sure that the connector is attached firmly.
2030 LCD panel For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1040 DIMM slot cover” on page 67 v “1060 PCI Express Mini Card for wireless WAN” on page 69 v “1120 Palm rest” on page 78 v “1140 PCI Express Mini Card for wireless LAN/WiMAX” on page 82 v “1150 Keyboard” on page 84 v “1170 Top case sub assembly” on page 87 v “1200 LCD unit” on page 92 v “2010 LCD front bezel” on page 103 Table 3
Table 38. Removal steps of LCD panel (continued) 4 3 2 When installing: Make sure that the LCD cable is attached firmly.
2040 Antenna assembly, LCD cable, camera cable, and hinges For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1040 DIMM slot cover” on page 67 v “1060 PCI Express Mini Card for wireless WAN” on page 69 v “1120 Palm rest” on page 78 v “1140 PCI Express Mini Card for wireless LAN/WiMAX” on page 82 v “1150 Keyboard” on page 84 v “1170 Top case sub assembly” on page 87 v “1200 LCD unit” on page 92
Table 39.
Table 39. Removal steps of antenna assemblies and camera cable (continued) a a b b 3 3 4 3 5 3 4 5 Step Screw (quantity) Color Torque 3 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.167 Nm (1.7 kgfcm) 4 M2 × 3 mm, shoulder, wafer-head, nylon-coated (4) Black 0.167 Nm (1.
Table 39.
Table 40. Installation of the antenna assemblies and the camera cable When you install the antenna assembly and the camera cable, place them as shown in this figure. a Wireless LAN antenna, AUX (black) b Wireless WAN antenna, AUX (blue) c Camera cable (some models) d Wireless WAN antenna, MAIN (red) e Wireless LAN antenna, MAIN (gray) f MIMO antenna (white) a b c d e f When installing: The WLAN module and WWAN module must be from the same vendor.
Locations Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 112 Built-in microphone Integrated camera Built-in stereo speakers Power switch System status indicators Note: For the description of each indicator, see “Status indicators” on page 52.
1 2 1 3 21 20 3 18 17 4 16 19 15 14 5 13 6 7 8 9 12 10 11 ThinkPad SL300 113
Rear view 1 2 3 4 5 6 7 IEEE 1394 connector 7–in1 Media Card Reader USB (Universal serial bus) connectors HDMI port External monitor connector RJ-11 (modem) connector Security key hole 7 6 2 3 5 4 Bottom view 1 2 3 4 5 6 Battery pack Battery pack latch Thermal slot Hard disk drive Wireless switch Expansion slot 1 2 6 3 5 114 ThinkPad SL300 Hardware Maintenance Manual 4 1
Parts list This section contains following lists of the service parts. v “Overall” on page 116 v “LCD FRUs” on page 129 v “Keyboard” on page 132 v “Miscellaneous parts” on page 133 v “AC adapters” on page 134 v “Power cords” on page 135 v “Recovery discs” on page 136 v “Common service tools” on page 141 Notes: v Each FRU is available for all types or models, unless specific types or models are specified.
Overall 1 26 25 24 2 23 5 22 3 d 21 4 20 5 19 18 a 6 17 16 b 15 c 14 7 13 12 8 11 9 10 116 ThinkPad SL300 Hardware Maintenance Manual
Table 41. Parts list—Overall No. FRU FRU no. RoHS CRU ID ID a - d See “Miscellaneous parts” on page 133. 1 LCD unit (see “LCD FRUs” on page 129.
Table 41. Parts list—Overall (continued) No. 118 FRU FRU no. RoHS CRU ID ID 4 CPU assembly, Intel Celeron Dual Core processor T1700 42W8147 (1.83 GHz) v 2738-CTO, 92x, 96x, 9Bx, 9Ux R N 4 CPU assembly, Intel Core 2 Duo mobile processor P7370 (2.0 GHz) v 2738-CTO, 28x, 2Bx, 2Kx, 2Lx, 2Mx, 2Nx, 2Rx, 2Sx, 5Yx, 8Zx, 9Gx, 9Hx, 9Jx, 9Kx, 9Lx, 9Yx, J7x, J8x, J9x, JAx, JSx, JTx, JUx, JVx 42W8149 R N 4 CPU assembly, Intel Core 2 Duo mobile processor P8400 (2.
Table 41. Parts list—Overall (continued) No. FRU FRU no. RoHS CRU ID ID 4 CPU assembly, Intel Core 2 Duo mobile processor T5870 (2.0 GHz) v 2738-CTO, 27x, 2Ax, 2Cx, 2Px, 2Qx, 2Tx, 2Ux, 2Zx, 4Nx, 5Vx, 6Dx, 6Hx, 6Nx, 6Px, 6Sx, 6Tx, 6Ux, 77x, 7Ax, 7Vx, 84x, 8Xx, 8Yx, 9Wx, A2x, A3x, A4x, A5x, A6x, A7x, A8x, A9x, AAx, ABx, HQx, HRx, HSx, HTx, HUx, HVx, HWx, HXx, HYx, HZx, JFx, JGx, JHx, JJx, JKx, JLx, K3x 43N7739 R N 4 CPU assembly, Intel Core 2 Duo mobile processor T6570 (2.
Table 41. Parts list—Overall (continued) No. 120 FRU FRU no. RoHS CRU ID ID 7 Battery pack, Li-ion (6 cell, 2.
Table 41. Parts list—Overall (continued) No. FRU FRU no. RoHS CRU ID ID 7 Battery pack, Li-ion (6 cell, 2.
Table 41. Parts list—Overall (continued) No. 122 FRU FRU no. RoHS CRU ID ID 9 DVD multi drive, 12.
Table 41. Parts list—Overall (continued) No. FRU FRU no. RoHS CRU ID ID 9 Blu-ray combo drive, 12.7 mm v 2738-CTO, 2Px, 2Tx, 3Dx, 3Ex, 5Bx, 6Lx, 6Nx, 6Qx, 6Sx, 7Px, 7Tx, 8Hx, 9Cx, 9Ex, H3x, HGx, HHx 42T2579 R * 9 Blu-ray drive, 12.7 mm v 2738-CTO, 22x 41W0037 R * 10 DIMM cover with screw 13W 45N4310 R * 11 Thermal door with screw 13W 45N3197 R * 12 SATA hard disk drive, 80 GB, 9.
Table 41. Parts list—Overall (continued) No. 124 FRU FRU no. RoHS CRU ID ID 12 SATA hard disk drive, 250 GB, 9.
Table 41. Parts list—Overall (continued) No. FRU FRU no.
Table 41. Parts list—Overall (continued) No. 126 FRU FRU no.
Table 41. Parts list—Overall (continued) No. FRU FRU no. RoHS CRU ID ID 22 Bluetooth daughter card (BDC-2.
Table 41. Parts list—Overall (continued) No. 128 FRU FRU no.
LCD FRUs In ThinkPad SL300, there is a following type of LCD. v “13.3-in. WXGA TFT” 13.3-in.
Table 42. Parts list—13.3-in. WXGA TFT No. 130 FRU FRU no.
Table 42. Parts list—13.3-in. WXGA TFT (continued) No. FRU FRU no.
Keyboard Table 43. Parts list—Keyboard 132 Language P/N Arabic 42T3884 42T3818 Belgian 42T3881 42T3815 Brazilian Portuguese 42T3900 42T3834 Bulgarian 42T4144 42T4140 Canadian French (058) 42T3871 42T3805 Canadian French (Acnor) 42T3870 42T3804 Czech 42T3889 42T3823 Danish 42T3878 42T3812 Dutch 42T3875 42T3809 Finnish, Swedish 42T3876 42T3810 French 42T3874 42T3808 German 42T3872 42T3806 Greek (U.S.
Miscellaneous parts Table 44. Parts list—Miscellaneous parts FRU P/N RoHS ID CRU ID Screw kit (including nylon-coated screws): v M1.6 × 4 mm v M2 × 2 mm v M2 × 3 mm v M2 × 4 mm v M2 × 5 mm v M2 × 6 mm v M2 × 7 mm v M2 × 8 mm v M2 × 9 mm v M2 × 12 mm v M2 × 15 mm v M2 × 16 mm v M2.5 × 5 mm v M2.5 × 6 mm v M2.
AC adapters Table 45.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 47. Parts list—2-pin power cords Region P/N Argentina v models -CTO, xxY 42T5020 42T5105 Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.S. v models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan v models -CTO, xxE, xxJ 42T5014 42T5099 RoHS ID CRU ID R * RoHS ID CRU ID R * Table 48.
Recovery discs Windows XP Professional DVDs Windows XP Professional is preinstalled as the operating system in the following models: v 2738-CTO, 2Mx, 2Nx, 2Zx, 72x, 73x, 74x, 75x, 76x, 77x, 78x, 79x, 7Ax, 7Bx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 7Hx, 7Jx, 7Lx, 7Mx, 7Nx, 7Px, 7Qx, 7Rx, 7Sx, 7Tx, 7Ux, 7Vx, 7Wx, 7Xx, 7Yx, 7Zx, 82x, 8Fx, 8Hx, 8Jx, 8Lx, 8Mx, 8Nx, 8Zx, 9Cx, 9Dx, 9Hx, 9Jx, 9Mx, A2x, AAx, ABx, ACx, ADx, AEx, AFx, H3x, H6x, H8x, HAx, HCx, K3x, L2x, L3x, L4x, L5x Table 49.
Windows Vista Home Basic (32 bit) DVDs Windows Vista Home Basic (32 bit) is preinstalled as the operating system in the following models: v 2738-CTO, 27x, 28x, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 3Dx, 3Sx, 3Tx, 3Ux, 4Lx, 5Bx, 5Gx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 62x, 65x, 6Cx, 6Dx, 6Gx, 6Lx, 6Mx, 6Nx, 6Px, 6Qx, 6Rx, 6Sx, 6Tx, 6Ux, 6Zx, 85x, 8Sx, 8Ux, 8Wx, 93x, 97x, 99x, 9Bx, 9Vx, A5x, HNx, HPx, HQx, HSx, HUx, HVx, HWx, HXx, HYx, HZx, J2x, J3x, J4x, J5x, J6x, J7x, J8x, J9x, JAx, JBx, JCx, JDx, JE
Windows Vista Home Premium (32 bit) DVDs Windows Vista Home Premium (32 bit) is preinstalled as the operating system in the following models: v 2738-CTO, 3Fx, 3Hx, 3Kx, 3Mx, 4Bx, 4Ex, 5Jx, 5Lx, 64x, 66x, 69x, 6Jx, 84x, 9Px, 9Qx, 9Rx, 9Sx, 9Tx, 9Ux, 9Wx, 9Xx, 9Yx, A4x Table 51.
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 2738-CTO, 23x, 24x, 25x, 26x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Jx, 2Kx, 2Lx, 33x, 34x, 36x, 37x, 39x, 3Ax, 3Bx, 3Ex, 3Gx, 3Lx, 3Qx, 3Yx, 3Zx, 42x, 43x, 44x, 46x, 48x, 49x, 4Cx, 4Dx, 4Fx, 4Hx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Xx, 4Yx, 4Zx, 52x, 53x, 5Fx, 5Hx, 5Kx, 5Ux, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 63x, 67x, 68x, 6Ax, 6Bx, 6Ex, 6Fx, 6Hx, 6Kx, 6Vx, 6Wx, 6Xx, 86x, 8Bx, 8Cx, 8Dx, 8Ex, 8Qx, 8Tx, 8
Windows Vista Ultimate (32 bit) DVDs Windows Vista Ultimate (32 bit) is preinstalled as the operating system in the following models: v 2738-CTO, 22x Table 53.
Common service tools Table 54. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4″ drive spinner handle 1650840 1/4″ Sq. to 1/4″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
142 ThinkPad SL300 Hardware Maintenance Manual
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Part Number: 43Y6763_03 (1P) P/N: 43Y6763_03
