Desktop Computer Hardware Maintenance Manual
Table Of Contents
- Contents
- Chapter 1. About this manual
- Chapter 2. Safety information
- Chapter 3. General information
- Chapter 4. General checkout
- Chapter 5. Diagnostics
- Chapter 6. Using the Setup Utility
- Chapter 7. Symptom-to-FRU index
- Chapter 8. Replacing FRUs (Machine Types: 3063, 3231, 3285, 6138, 6209, 6239, 6302, 7188, 7244, 7347, 7355, 7358, 7373, 7484, 7571, 7628, 7635, 7639, 8494, 8854, 9728, 9960, and 9965.)
- Locating connectors on the front of the computer
- Locating connectors on the rear of the computer
- Removing the computer cover
- Locating components
- Locating parts on the system board
- Removing and reinstalling the front bezel
- Replacing a memory module
- Replacing the power supply
- Replacing the heat sink and fan assembly
- Replacing the microprocessor
- Replacing the system board
- Replacing the battery
- Replacing an adapter card
- Replacing the primary hard disk drive
- Replacing the secondary hard disk drive
- Replacing the optical drive
- Replacing the diskette drive
- Replacing the front fan assembly
- Replacing the rear fan assembly
- Replacing the front audio and USB assembly
- Replacing the internal speaker
- Completing the FRU replacement
- Chapter 9. Replacing FRUs (Machine Types: 3379, 5897, 6137, 6234, 6258, 6303, 7174, 7220, 7346, 7354, 7357, 7360, 7483, 7582, 7627, 7630, 7638, 8910, and 9964.)
- Locating connectors on the front of the computer
- Locating connectors on the rear of the computer
- Opening the computer cover
- Accessing the system board components and drives
- Locating components
- Locating parts on the system board
- Replacing the battery
- Replacing a memory module
- Replacing an adapter card
- Replacing the power supply
- Replacing the heat sink and fan assembly
- Replacing the microprocessor
- Replacing the system board
- Replacing the hard disk drive
- Replacing the optical drive
- Replacing the card reader
- Replacing the internal speaker
- Replacing the front audio and USB assembly
- Completing the FRU replacement
- Chapter 10. FRU lists
- Machine Type 3379
- Machine Type 6137
- Machine Type 6138
- Machine Type 6209
- Machine Type 6234
- Machine Type 6239
- Machine Type 6258
- Machine Type 6302
- Machine Type 7174
- Machine Type 7188
- Machine Type 7220
- Machine Type 7244
- Machine Type 7346
- Machine Type 7347
- Machine Type 7354
- Machine Type 7355
- Machine Type 7357
- Machine Type 7358
- Machine Type 7360
- Machine Type 7373
- Machine Type 7483
- Machine Type 7484
- Machine Type 7628
- Machine Type 7635
- Machine Type 7638
- Machine Type 7639
- Machine Type 8854
- Machine Type 8910
- Machine Type 9960
- Machine Type 9964
- Machine Type 9965
- Chapter 11. Additional service information
- Appendix. Notices
8. Reinstall or close the computer cover and reconnect the power cords for the
computer and monitor to electrical outlets. See “Completing the FRU
replacement” on page 122 or “Completing the FRU replacement” on page 158.
9. Turn on the computer and the monitor, and then insert the POST/BIOS
update (flash update) disc into the optical drive.
10. Turn the computer off and back on again.
11. The recovery session will take two to three minutes. During this time you will
hear a series of beeps. After the update session is completed, there will be no
video, the series of beeps will end, and the system will automatically turn off.
Remove the disc from the optical drive before the system completely turns off.
12. Repeat steps 2 through 5.
13. Move the jumper back to the standard position (pin 1 and pin 2).
14. Reconnect any cables that were disconnected.
15. Reinstall or close the computer cover and reconnect the power cords for the
computer and monitor to electrical outlets. See “Completing the FRU
replacement” on page 122 or “Completing the FRU replacement” on page 158.
16. Turn on the computer to restart the operating system.
Power management
Power management reduces the power consumption of certain components of the
computer such as the system power supply, processor, hard disk drives, and some
monitors.
Automatic configuration and power interface (ACPI) BIOS
Being an ACPI BIOS system, the operating system is allowed to control the power
management features of the computer and the setting for Advanced Power
Management (APM) BIOS mode is ignored. Not all operating systems support
ACPI BIOS mode.
Automatic Power-On features
The Automatic Power-On features within the Power Management menu allow you
to enable and disable features that turn on the computer automatically.
v RTC resume: You can specify a date and time at which the computer will be
turned on automatically. This can be either a single event or a daily event.
v Wake on LAN: If the computer has a properly configured token-ring or Ethernet
LAN adapter card that is Wake on LAN-enabled and there is remote network
management software, you can use the Wake on LAN feature. When you set
Wake on LAN to Enabled, the computer will turn on when it receives a specific
signal from another computer on the local area network (LAN).
Chapter 11. Additional service information 657