Desktop Computer Hardware Maintenance Manual
Table Of Contents
- Contents
- Chapter 1. About this manual
- Chapter 2. Safety information
- Chapter 3. General information
- Chapter 4. General checkout
- Chapter 5. Diagnostics
- Chapter 6. Using the Setup Utility
- Chapter 7. Symptom-to-FRU index
- Chapter 8. Replacing FRUs (Machine Types: 3063, 3231, 3285, 6138, 6209, 6239, 6302, 7188, 7244, 7347, 7355, 7358, 7373, 7484, 7571, 7628, 7635, 7639, 8494, 8854, 9728, 9960, and 9965.)
- Locating connectors on the front of the computer
- Locating connectors on the rear of the computer
- Removing the computer cover
- Locating components
- Locating parts on the system board
- Removing and reinstalling the front bezel
- Replacing a memory module
- Replacing the power supply
- Replacing the heat sink and fan assembly
- Replacing the microprocessor
- Replacing the system board
- Replacing the battery
- Replacing an adapter card
- Replacing the primary hard disk drive
- Replacing the secondary hard disk drive
- Replacing the optical drive
- Replacing the diskette drive
- Replacing the front fan assembly
- Replacing the rear fan assembly
- Replacing the front audio and USB assembly
- Replacing the internal speaker
- Completing the FRU replacement
- Chapter 9. Replacing FRUs (Machine Types: 3379, 5897, 6137, 6234, 6258, 6303, 7174, 7220, 7346, 7354, 7357, 7360, 7483, 7582, 7627, 7630, 7638, 8910, and 9964.)
- Locating connectors on the front of the computer
- Locating connectors on the rear of the computer
- Opening the computer cover
- Accessing the system board components and drives
- Locating components
- Locating parts on the system board
- Replacing the battery
- Replacing a memory module
- Replacing an adapter card
- Replacing the power supply
- Replacing the heat sink and fan assembly
- Replacing the microprocessor
- Replacing the system board
- Replacing the hard disk drive
- Replacing the optical drive
- Replacing the card reader
- Replacing the internal speaker
- Replacing the front audio and USB assembly
- Completing the FRU replacement
- Chapter 10. FRU lists
- Machine Type 3379
- Machine Type 6137
- Machine Type 6138
- Machine Type 6209
- Machine Type 6234
- Machine Type 6239
- Machine Type 6258
- Machine Type 6302
- Machine Type 7174
- Machine Type 7188
- Machine Type 7220
- Machine Type 7244
- Machine Type 7346
- Machine Type 7347
- Machine Type 7354
- Machine Type 7355
- Machine Type 7357
- Machine Type 7358
- Machine Type 7360
- Machine Type 7373
- Machine Type 7483
- Machine Type 7484
- Machine Type 7628
- Machine Type 7635
- Machine Type 7638
- Machine Type 7639
- Machine Type 8854
- Machine Type 8910
- Machine Type 9960
- Machine Type 9964
- Machine Type 9965
- Chapter 11. Additional service information
- Appendix. Notices

ATTENTION:
Remplacer la pile au lithium usagée par une pile de référence identique
exclusivement, (référence 33F8354), ou suivre les instructions du fabricant qui en
définit les équivalences. Si votre système est doté d’un module contenant une
pile au lithium, vous devez le remplacer uniquement par un module identique,
produit par le même fabricant. La pile contient du lithium et peut exploser en
cas de mauvaise utilisation, de mauvaise manipulation ou de mise au rebut
inappropriée.
Ne pas :
v la jeter à l’eau,
v l’exposer à des températures supérieures à 100°C,
v chercher à la réparer ou à la démonter.
Ne
pas mettre la pile à la poubelle. Pour la mise au rebut, se reporter à la
réglementation en vigueur.
ATTENTION:
Si des produits à laser (tels que des unités de CD-ROM, de DVD-ROM, des
unités à fibres optiques, ou des émetteurs) sont installés, prenez connaissance
des informations suivantes :
v Ne retirez pas le carter. En ouvrant l’unité de CD-ROM ou de DVD-ROM,
vous vous exposez au rayonnement dangereux du laser. Aucune pièce de
l’unité n’est réparable.
v Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de
réglage et d’utilisation des commandes, ainsi que les procédures décrites dans
le présent manuel.
DANGER
Certains produits à laser contiennent une diode à laser intégrée de classe 3A ou
3B. Prenez connaissance des informations suivantes:
Rayonnement laser lorsque le carter est ouvert. Evitez toute expositiondirecte au
rayon laser. Evitez de regarder fixement le faisceau ou del’observer à l’aide
d’instruments optiques.
22 Hardware Maintenance Manual










