ThinkServer TD230 Hardware Maintenance Manual Machine Types: 1027, 1029, 1039, and 1040
ThinkServer TD230 Hardware Maintenance Manual Machine Types: 1027, 1029, 1039, and 1040
Note: Before using this information and the product it supports, read the general information in Appendix C “Notices” on page 167 and the Warranty and Support Information document on the ThinkServer Documentation DVD. Eighth Edition (October 2011) © Copyright Lenovo 2010, 2011. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents Chapter 1. About this manual . . . . . . 1 Safety information . . . . . . . . . . . . . . Important information about replacing RoHS compliant FRUs . . . . . . . . . . . . . . . Chapter 2. General information . . . . Features and specifications. . . . . . Software programs . . . . . . . . . EasyStartup . . . . . . . . . . EasyManage. . . . . . . . . . Reliability, availability, and serviceability. . . . . . . . . . . . . . . . 1 Locating connectors on the hot-swap hard disk drive backplanes .
Chapter 6. Parts listing, TD230 Types 1027, 1029, 1039, and 1040 . . . . . 125 Appendix A. RAID battery card assembly . . . . . . . . . . . . . . Replaceable server components. . . . . . . . Power cords . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . Battery life and data retention time . . . . . Chapter 7. Configuring the server . Using the Setup Utility program . . . . . . Starting the Setup Utility program . . . Introduction of the BIOS items. . . . . Using passwords . . .
Chapter 1. About this manual This Hardware Maintenance Manual contains information to help you solve problems that might occur in your server. It describes the diagnostic tools that come with the server, error codes and suggested actions, and instructions for replacing failing components. Replaceable components are of three types: • Self-service customer replaceable unit (CRU): Replacement of self-service CRUs is your responsibility.
Πριν χρησιμοποιήσετε το προϊόν, βεβαιωθείτε ότι έχετε διαβάσει και κατανοήσει τις οδηγίες ασφάλειας, οι οποίες είναι διαθέσιμες σε διάφορες γλώσσες στο DVD τεκμηρίωσης που συνοδεύει το προϊόν. Vor Verwendu ng des Produkts sollten Sie unbedingt die mehrsprachigen Sicherheitsanweisungen auf der Dokumentations-DVD lesen, die im Lieferumfang des Produkts enthalten ist.
使用本產品之前，請務必閱讀並瞭解產品隨附的文件 DVD 上的多國語言版本安全資訊。 Bu ürünü kullanmadan önce, ürünle birlikte gönderilen belge DVD'si üzerindeki çok dil içeren güvenlik yönergelerini okuyup anladýðýnýzdan emin olun. Перед використанням цього продукту уважно ознайомтеся з інструкціями з техніки безпеки на різних мовах, що можна знайти на DVD-диску з документацією в комплекті з продуктом. Important: Each caution and danger statement in this topic is labeled with a number.
Statement 2 DANGER Danger of explosion if battery is incorrectly replaced. When replacing the lithium coin cell battery, use only the same or an equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations.
Statement 4 ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5 lb) ≥ 55 kg (121.2 lb) < 32 kg (70.5 lb) < 55 kg (121.2 lb) < 100 kg (220.5 lb) CAUTION: Use safe practices when lifting. Statement 5 CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
Statement 8 CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. Statement 9 CAUTION: To avoid personal injury, disconnect the hot-swap fan cables before removing the fan from the device.
Statement 13 CAUTION: Make sure that the rack is secured properly to avoid tipping when the server unit is extended. Statement 14 CAUTION: Some accessory or option board outputs exceed Class 2 or limited power source limits and must be installed with appropriate interconnecting cabling in accordance with the national electric code. Statement 15 CAUTION: The power-control button on the device does not turn off the electrical current supplied to the device.
Statement 18 CAUTION: Do not place any object on top of rack-mounted devices. Statement 19 CAUTION: Hazardous moving parts. Keep fingers and other body parts away. Statement 20 CAUTION: The battery is a lithium ion battery. To avoid possible explosion, do not burn the battery. Exchange it only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations.
RoHS compliant ThinkServer™ TD230 parts have unique FRU part numbers. Before or after June 2006, failed RoHS compliant parts must always be replaced using RoHS compliant FRUs, so only the FRUs identified as compliant in the system Hardware Maintenance Manual or direct substitutions for those FRUs can be used.
10 ThinkServer TD230 Hardware Maintenance Manual
Chapter 2. General information This chapter provides some general information about your server. Features and specifications The following table provides information about the features and specifications of the server. Depending on the server model, some features might not be available, or some specifications might not apply. For information about your specific model, use the Setup Utility program. See “Using the Setup Utility program” on page 143. Table 1.
Table 1. Features and specifications (continued) • ThinkServer RAID 500 Adapter (9240-8i) • ThinkServer 8708EM2 RAID Adapter Integrated functions: • Ethernet controllers (The server comes with two integrated Gigabit Ethernet controllers, which support connection to 10 Mbps, 100 Mbps, or 1000 Mbps network. For more information, see “Configuring the Gigabit Ethernet controller” on page 157.
• Advanced Desktop Management Interface (DMI) • Automatic memory downsizing on error detection • Automatic restart on non-maskable interrupt (NMI) • Availability of microcode level • Built-in, menu-driven setup, system configuration, and RAID configuration • Built-in monitoring for fan, temperature, and voltage • Cooling fans with speed-sensing capability • ECC DDR3 SDRAM with Serial Presence Detect (SPD) • Error codes and messages to help you identify problems • Generating error logs for the power-on self-
14 ThinkServer TD230 Hardware Maintenance Manual
Chapter 3. Diagnostics This chapter describes the diagnostic tools that are available to help you solve problems that might occur in the server. If you cannot diagnose and correct a problem by using the information in this chapter, see Appendix B “Getting help and technical assistance” on page 163 for more information. Troubleshooting tables Use the troubleshooting tables to find solutions to problems that have identifiable symptoms.
Symptom Action 3. Replace the DVD drive. The DVD drive tray is not working. 1. Make sure that the server is turned on. 2. Insert the end of a straightened paper clip into the manual tray-release opening. 3. Reseat the DVD drive. 4. Replace the DVD drive. General problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
Symptom A problem occurs only occasionally and is difficult to diagnose. Action 1. Make sure that: • All cables and cords are connected securely to the rear of the server and attached devices. • When the server is turned on, air is flowing from the fan grille. If there is no airflow, the fan is not working. This can cause the server to overheat and shut down. 2. Check the system-event log (see “Event logs” on page 25). 3. See “Solving undetermined problems” on page 24.
• See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Symptom The amount of system memory that is displayed is less than the amount of installed physical memory. Action 1.
Symptom The server emits a continuous beep during the POST, indicating that the startup (boot) microprocessor is not working correctly. Action 1. Make sure that the server supports all the microprocessors and that the microprocessors match in speed and cache size. 2. (Trained service technician only) Reseat microprocessor 1. 3. (Trained service technician only) If there is no indication of which microprocessor has failed, isolate the error by testing with one microprocessor at a time. 4.
Symptom The monitor has screen jitter, or the screen image is wavy, unreadable, rolling, or distorted. Action 1. If the monitor self-tests show that the monitor is working correctly, consider the location of the monitor. Magnetic fields around other devices (such as transformers, appliances, fluorescent lights, and other monitors) can cause screen jitter or wavy, unreadable, rolling, or distorted screen images. If this happens, turn off the monitor.
Symptom Action 3. Replace the device that you just installed. A Lenovo optional device that used to work does not work now. 1. Make sure that all of the hardware and cable connections for the device are secure. 2. If the device comes with test instructions, use those instructions to test the device. 3. If the failing device is an SCSI device, make sure that: • The cables for all external SCSI devices are connected correctly.
Symptom Action 5. If you just installed an optional device, remove it, and restart the server. If the server now starts, you might have installed more devices than the power supply supports. 6. See “Solving undetermined problems” on page 24. The server does not turn off. 1. Determine whether you are using an Advanced Configuration and Power Interface (ACPI) or a non-ACPI operating system. If you are using a non-ACPI operating system, do the following: a. Press Ctrl+Alt+Delete. b.
Software problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Symptom You suspect a software problem. Action 1.
3. Remove the adapters and disconnect the cables and power cords to all internal and external devices until the server is at the minimum configuration that is required for the server to start (see “Solving undetermined problems” on page 24 for the minimum configuration). 4. Reconnect all ac power cords and turn on the server. If the server starts successfully, replace the adapters and devices one at a time until the problem is isolated.
Check the LEDs on all the power supplies. If the LEDs indicate that the power supplies are working correctly, do the following: 1. Turn off the server. 2. Make sure that the server is cabled correctly. 3. Remove or disconnect the following devices, one at a time, until you find the failure. Turn on the server and reconfigure it each time.
progress code can be customized to fit the data width. The higher the data bit, the higher the granularity of information that can be sent on the progress port. The progress codes may be reported by the system BIOS or option ROMs. The response has three types: • Minor: The message displays on the screen or on the Error Manager screen, and an error is logged to the SEL. The system continues booting in a degraded state. The user may want to replace the erroneous unit.
Chapter 4. Locating parts, controls, LEDs, and connectors This chapter provides information to help you locate your server parts, controls, light-emitting diodes (LEDs), and connectors. Front view Figure 1 “Front view of the server” on page 27 shows the LEDs and parts on the front of the server. Figure 1.
Figure 2. Opening the front door Figure 3 “Front view of the server (with the front door open)” on page 29 shows the controls, LEDs, connectors, and other parts on the front panel after you open the front door.
Figure 3. Front view of the server (with the front door open) 1 5.25-inch drive bay 7 Reset button 2 Power LED 8 USB connectors (2) 3 Hard disk drive status LED 9 3.5-inch drive bay 4 Ethernet status LED 10 Optical drive eject/close button 5 System status LED 11 Optical drive 6 Power button The following table describes the various meanings of the status LEDs on the front panel of your server. Table 2.
Table 2. Meanings of the status LEDs on the front panel (continued) LED Ethernet status LED System status LED State Color Description On Green The server is linked to a local area network (LAN). Blinking Green The LAN is active and data is being transferred. Off Off The server is not linked to a LAN. On Green The system has finished initialization. Note: The system status LED will initially turn amber when the system is plugged in.
Figure 4. Rear view of the server 1 Power cord connector 5 PCI card zone 2 Serial port 6 Ethernet connector 2 3 VGA monitor connector 7 Ethernet connector 1 4 USB connectors (4) 8 Front door key (cut the plastic clip to get the key) Hot-swap hard disk drive status LEDs For server models with hot-swap hard disk drives, each hot-swap hard disk drive also has two status LEDs on the front. Figure 5. Hot-swap hard disk drive status LEDs Chapter 4.
Table 3. Hot-swap hard disk drive status LEDs Hot-swap hard disk drive status LED 1 Hot-swap hard disk drive present LED 2 Hot-swap hard disk drive activity LED State Description On The hot-swap hard disk drive is present. Off The hot-swap hard disk drive is not present. On The hot-swap hard disk drive is active. Off The hot-swap hard disk drive is not active.
Figure 6.
34 33 32 31 Figure 7. Locating major parts on the system board 1 Main power connector 18 SATA connector 0 2 Front panel connector 19 SATA connector 1 3 Memory slot - microprocessor 1 DIMM channel B1 (CPU1 DIMM CHB1) 20 SATA connector 2 4 Memory slot (CPU1 DIMM CHB2) 21 SATA connector 3 5 Memory slot (CPU1 DIMM CHA1) 22 SATA connector 4 6 Memory slot (CPU1 DIMM CHA2) 23 Internal dual-port USB 2.0 connector (ports 0-1) 7 System fan 2 connector 24 Internal dual-port USB 2.
16 Memory slot (CPU2 DIMM CHE2) 33 System board battery 17 Memory slot (CPU2 DIMM CHE1) 34 System fan 3 connector Locating diagnostic LEDs on the system board There are several diagnostic LEDs on the system board to help you diagnose specific problems. Figure 8 “Diagnostic LEDs on the system board” on page 35 shows the locations of the diagnostic LEDs on the system board. Figure 8.
1 2 3 3 2 1 1 2 3 1 2 3 1 2 3 Figure 9. Jumper blocks on the system board Table 5. Jumper block settings Jumper block 1 J8B5: ME Force Update Pin position Description Pins 1-2 These pins should have a jumper in place for normal system operation (default). Pins 2-3 ME force update model.
Note: Before clearing the CMOS, turn off the server and disconnect the power cord. Move the jumper from pins 1-2 to pins 2-3. Wait more than five minutes; then, move the jumper back to the normal position (pins 1-2 is short circuited) to clear CMOS. Locating connectors on the hot-swap hard disk drive backplanes There are two hot-swap hard disk drive backplanes installed in the server model with hot-swap hard disk drives.
38 ThinkServer TD230 Hardware Maintenance Manual
Chapter 5. Replacing FRUs This chapter provides detailed instructions for replacing FRUs in the server. FRU replacements are to be done only by trained service technicians. This chapter does not contain the remove or replace procedure for all FRUs. Only the major FRUs are documented. Guidelines This section provides some guidelines that you should read and understand before using your server.
• To view the error LEDs on the system board and internal components, leave the server connected to power. • You do not have to turn off the server to install or replace hot-swap fans, redundant hot-swap ac power supplies, or hot-plug USB devices. However, you must turn off the server before performing any steps that involve installing, removing, or replacing adapter cables or non-hot-swap optional devices or components.
• Take additional care when handling devices during cold weather. Heating reduces indoor humidity and increases static electricity. Working inside the server with the power on Attention: Static electricity that is released to internal server components when the server is turned on might cause the server to halt, which might result in the loss of data.
4. Remove the cover. 5. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 6. Check inside the server for any obvious unsafe conditions, such as metal filings, contamination, water or other liquid, or signs of fire or smoke damage. 7. Check for worn, frayed, or pinched cables. 8. Make sure that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Removing the server cover Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to remove the server cover.
4. Loosen the two thumbscrews attached on the rear of the server cover and then slide the server cover to the rear. Notes: a. The two thumbscrews are securely installed and you need to use a tool, for example a screw driver, to loosen the thumbscrews. b. The two thumbscrews are integrated parts of the server cover and they cannot be removed from the server cover. Figure 11.
5. Pivot the server cover outward to completely remove it. Figure 12. Removing the server cover To reinstall the server cover, see “Installing the server cover” on page 122. Removing and reinstalling the front bezel Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39.
3. Remove the front bezel by releasing the three plastic tabs 1 on the left side and pulling the front bezel outward. Figure 13. Removing the front bezel 4. To reinstall the front bezel, align the other three plastic tabs on the right side of the front bezel with the corresponding holes in the chassis, then pivot the front bezel inward until it snaps into position on the left side. 5. Go to “Completing the parts replacement” on page 122.
The hard disk drive side door of the server is unlocked when shipped from the factory. You can open the side door to view the hot-swap hard disk drive LED status, install a new hard disk drive, and remove or replace a failing hard disk drive. However, you can also lock the hard disk drive side door to ensure that all the hard disk drives cannot be accessed unless you remove the server cover.
2. Rotate the plastic latch of the side door to the closed position. Then, close the side door until it snaps into position. The side door is locked and cannot be opened when you press the blue button. Figure 15.
3. To unlock the side door, remove the server cover. See “Removing the server cover” on page 43. Then, rotate the plastic latch of the side door to the open position. Reinstall the server cover. See “Installing the server cover” on page 122. The side door is unlocked and you can open the side door by pressing the blue button on it, as shown in Figure 14 “Opening the side door” on page 47. Figure 16.
Table 6. Memory module installation rules CPU CPU 1 DIMM CPU1 DIMM CHA2 Four DIMMs CPU1 DIMM CHB2 CPU1 DIMM CHB1 CPU2 DIMM CHD2 CPU2 DIMM CHD1 CPU2 DIMM CHE2 CPU2 DIMM CHE1 X One DIMM Two DIMMs* CPU 1 and CPU 2 CPU1 DIMM CHA1 X, 1 X, 3 X, 1 X, 2 X, 4 X, 2 Two DIMMs X, 1 Four DIMMs* X, 1 X, 3 X, 3 X, 3 Six DIMMs X, 5 X, 1 Eight DIMMs X, 5 X, 1 X, 2 X, 7 X, 2 X, 4 X, 6 X, 2 X, 4 X, 6 X, 2 X, 8 X, 4 Note: * denotes the Channel Mirroring Mode.
4. Open the retaining clips of the memory slot into which you want to install the memory module. Figure 17. Opening the retaining clips of the memory slot 5. Touch the static-protective package that contains the new memory module to any unpainted metal surface on the outside of the server. Then, remove the new memory module from the package. 6. Position the new memory module over the memory slot. Make sure that the notch 1 on the new memory module is aligned with the key 2 in the memory slot.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 43. 3. Locate the memory slot with the memory module that you want to remove. See “Locating parts on the system board” on page 33 for the locations of the memory slots. 4.
Removing the optical drive Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to remove the optical drive. To remove the optical drive, do the following: 1.
6. Remove the optical drive retainers from both sides of the old optical drive and save them to use when you install a new optical drive. Figure 21. Removing the optical drive retainers 7. If you are instructed to return the removed optical drive to the manufacturer, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. 8. To complete the removal procedure, go to “Completing the parts replacement” on page 122.
DANGER Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following. Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Class 1 Laser Product Laser Klasse 1 Laser Klass 1 Luokan 1 Laserlaite Appareil A` Laser de Classe 1 2. Remove all media from the drives and turn off all attached devices and the server.
7. Slide the new optical drive into the drive bay until it snaps into position. Figure 23. Installing the optical drive 8. Connect one end of the signal cable 2 to the rear of the new optical drive and the other end to an available SATA connector (SATA connector 5 recommended) on the system board. See “Locating parts on the system board” on page 33. Then, locate an available five-wire power connector 1 and connect it to the rear of the new optical drive. Figure 24. Connecting the optical drive cables 9.
Removing a hot-swap hard disk drive Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to remove a hot-swap hard disk drive.
2. Locate the hot-swap hard disk drive you want to remove. Then, press the blue release button 1 and rotate the handle of the hard disk drive bracket to the open position. Figure 26.
3. Grasp the handle 1 and pull the hard disk drive bracket with the hard disk drive out of the drive bay. Figure 27. Removing the hot-swap hard disk drive bracket with the hard disk drive Chapter 5.
4. Remove the four screws that secure the hard disk drive and then remove the hard disk drive from the bracket. Figure 28. Removing the hot-swap hard disk drive 5. If you are instructed to return the removed hot-swap hard disk drive to the manufacturer, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. 6. To complete the removal procedure, go to “Completing the parts replacement” on page 122.
1. Press the blue button 1 to open the side door. Figure 29. Opening the side door Chapter 5.
2. Locate a hot-swap hard disk drive bay that you want to install the drive. Then, press the blue release button 1 and rotate the handle of the hard disk drive bracket to the open position. Figure 30.
3. Grasp the handle 1 and pull the hard disk drive bracket out of the drive bay. Figure 31. Removing the hot-swap hard disk drive bracket 4. Remove the plastic drive bay filler and save it for future use. Note: The EMI integrity and cooling of the server are protected by having all drive bays and PCI card slots covered or occupied. When you install a drive or PCI card, save the EMC shield or drive bay filler from the drive bay or save the PCI card slot cover in the event that you later remove the device.
6. Align the screw holes in both sides of the hard disk drive with the corresponding holes in the hard disk drive bracket. Then, install the four screws to secure the hard disk drive in the bracket. Note: Carefully install the hard disk drive without touching the circuit board on the bottom of the hard disk drive. Figure 32. Installing the hard disk drive into the bracket 7.
8. Press the handle 1 to rotate it to the closed position until the blue release button snaps into place and the bracket with the hard disk drive is securely locked in the drive bay. Figure 34. Locking the hot-swap hard disk drive in the drive bay 9. Check the hard disk drive status LEDs to make sure that the hard disk drive is operating correctly. You might have to restart the server for the newly installed drive to be recognized.
This section provides instructions on how to remove a non-hot-swap hard disk drive. This section applies only to server models that have non-hot-swap hard disk drives installed. Attention: To maintain proper system cooling, do not operate the server for more than 10 minutes without either a drive or a filler panel installed in each drive bay. To remove a non-hot-swap hard disk drive, do the following: 1. Remove all media from the drives and turn off all attached devices and the server.
3. Locate the non-hot-swap hard disk drive you want to remove and disconnect the power cable and the signal cable from the hard disk drive. Then, pull the handle of the hard disk drive bracket to slide the bracket with the hard disk drive out of the drive bay. Figure 36. Disconnecting cables and sliding the non-hot-swap hard disk drive out 4. Depending on the non-hot-swap hard disk drive is secured in the bracket by screws or plastic retainers, do one of the following: Chapter 5.
• If the non-hot-swap hard disk drive is secured in the bracket by screws, remove the four screws and then remove the hard disk drive from the bracket. Figure 37. Removing the screws that secure the hard disk drive • If the non-hot-swap hard disk drive is secured in the bracket by retainers, remove the retainers on both sides and then remove the hard disk drive from the bracket. Figure 38. Removing the retainers that secure the hard disk drive 5.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Press the blue button 1 to open the side door. Note: If you have locked the side door, you must turn off the server, disconnect all power cords, and remove the server cover when you want to remove, install, or replace any hard disk drives.
3. Locate a non-hot-swap hard disk drive bay that you want to install the drive. Then, pull the handle of the hard disk drive bracket to slide the bracket out of the drive bay. Figure 40. Sliding the non-hot-swap hard disk drive bracket out 4. Remove the plastic drive bay filler and save it for future use. Note: The EMI integrity and cooling of the server are protected by having all drive bays and PCI card slots covered or occupied.
• If you want to secure the hard disk drive in the bracket by screws, align the screw holes in both sides of the hard disk drive with the corresponding holes in the bracket. Then, install the four screws to secure the hard disk drive in the bracket. Figure 41. Securing the hard disk drive in the bracket by screws • If you want to secure the hard disk drive in the bracket by retainers, align the holes in both sides of the hard disk drive with the corresponding holes in the bracket.
7. Push the hard disk drive to slide the bracket with the hard disk drive into the drive bay until it snaps into position. Figure 43. Sliding the non-hot-swap hard disk drive into the bay 8. Locate an available five-wire power connector and an available signal cable connector. Then, connect the power cable and the signal cable to the hard disk drive. 9. To complete the installation, go to “Completing the parts replacement” on page 122.
Installing a PCI card Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to install a PCI card.
7. Position the new PCI card on the PCI card slot which you have removed the slot bracket in step 5 on page 73. Then, press the PCI card straight down until it is securely seated into the slot. Install the screw to secure the PCI card in place. Figure 44. Installing a PCI card 8. Depending on the type of the PCI card, you might need to connect any required cables to the PCI card. 9. To complete the installation, go to “Completing the parts replacement” on page 122.
2. Remove the server cover. See “Removing the server cover” on page 43. 3. Lay the server on its side for easier operation. 4. Locate the PCI card you want to remove. Then, depending on the type of the PCI card, you might need to disconnect any cables from the PCI card or the system board. 5. Remove the screw that secures the PCI card. Then, grasp the PCI card by the edges and carefully pull it out of the PCI card slot.
This section provides instructions on how to install the Ethernet card and how to install the Ethernet card driver on Windows operating systems. Use any documentation that came with the Ethernet card and follow those instructions in addition to the instructions in this section. To install the Ethernet card, do the following: 1. Remove all media from the drives and turn off all attached devices and the server.
5. If you are instructed to return the removed Ethernet card to the manufacturer, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. 6. To complete the removal procedure, go to “Completing the parts replacement” on page 122. Installing or removing the ThinkServer RAID 100 Upgrade Key for Advanced RAID This section provides instructions on how to install or remove the ThinkServer RAID 100 Upgrade Key for Advanced RAID (hereafter called the RAID 5 key).
5. Locate the SATA key connector on the system board. See “Locating parts on the system board” on page 33. Then, install the RAID 5 key into the SATA key connector. Figure 46. Installing the RAID 5 key What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation, go to “Completing the parts replacement” on page 122. Then, refer to Chapter 7 “Configuring the server” on page 143 for information about RAID configuration.
4. Remove the RAID 5 key from the SATA key connector on the system board. See “Locating parts on the system board” on page 33. Figure 47. Removing the RAID 5 key 5. If you are instructed to return the removed RAID 5 key to the manufacturer, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 43. 3. Lay the server on its side for easier operation. 4. Touch the static-protective package that contains the TR 500 key to any unpainted surface on the outside of the server. Then, remove the TR 500 key from the package. 5.
3. Lay the server on its side for easier operation. 4. Remove the ThinkServer RAID 500 Adapter. See “Removing the RAID card” on page 88 and follow those instructions to remove the ThinkServer RAID 500 Adapter. 5. Remove the TR 500 key from the ThinkServer RAID 500 Adapter. Figure 49. Removing the TR 500 key 6. If you are instructed to return the removed TR 500 key to the manufacturer, follow all packaging instructions and use any packaging materials that are supplied to you for shipping.
About the RMM3 The RMM3 is a 1.23-inch x 2.30-inch printed circuit board. Figure 50. RMM3 The RMM3 is a kind of add-on card which offers convenient, remote KVM (keyboard, video, and mouse) access and control through the LAN or Internet. It captures, digitizes, and compresses videos and transmits the videos with keyboard and mouse signals to and from a remote computer. You can use the RMM3 to gain location-independent remote access to respond to critical incidents and to undertake necessary maintenance.
4. Locate the RMM3 connector on the system board. See “Locating parts on the system board” on page 33. 5. Remove the corresponding PCI card slot bracket by removing the screw that secures the bracket. Save the PCI card slot bracket in the event that you later remove the RMM3 and need the bracket to cover the place. Note: Carefully place the removed screw aside. You will need the screw when installing the RMM3. Figure 51. Removing the PCI card slot bracket for the RMM3 connector 6.
8. Attach the RMM3 to the slot bracket that came with the option package so that the two screw holes in the slot bracket are aligned with the corresponding holes in the RMM3. Then, install the two screws that came with the option package to secure the RMM3 to the slot bracket. Notes: a. There are three screws in the option package and you only need to use two of them to secure the RMM3 to the slot bracket. The extra one is a backup screw. b.
9. Insert the slot bracket with RMM3 into the position for the PCI card slot bracket you have removed. Then, secure the slot bracket with RMM3 in place by installing the screw that you have removed in step 5 on page 83. Figure 53. Installing the slot bracket with RMM3 Chapter 5.
10. Remove the ribbon cable from the option package. Connect one end of the ribbon cable to the RMM3 connector on the system board. See “Locating parts on the system board” on page 33. Then, connect the other end of the ribbon cable to the connector on the RMM3. Figure 54. Connecting the ribbon cable What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation, go to “Completing the parts replacement” on page 122.
To remove the RMM3, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. Wait three to five minutes to let the server cool before removing the server cover. 2. Remove the server cover. See “Removing the server cover” on page 43. 3. Lay the server on its side for easier operation. 4. Locate the RMM3 in your server.
7. To complete the removal procedure, go to “Completing the parts replacement” on page 122. Installing, removing, or replacing hardware devices This section provides instructions on how to install, remove, or replace hardware devices for your server. You can maintain your server by replacing the failing hardware devices. If you are replacing a hardware device, perform the removal procedure and then perform the installation procedure for the hardware device that you want to replace.
Installing the RAID card This section provides instructions on the following: • “Installing the ThinkServer RAID 500 Adapter” on page 89 • “Installing the ThinkServer 8708EM2 RAID Adapter” on page 90 Note: This section only applies to server models with hot-swap hard disk drives.
9. Connect the mini SAS signal cables (port 0 to port 3) to the corresponding SATA/SAS signal connectors (connector 0 to connector 3) on the hot-swap hard disk drive backplanes. See “Locating connectors on the hot-swap hard disk drive backplanes” on page 37. Note: Each mini SAS signal cable might have a label attached. The number on the label indicates the port number. Figure 56.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 43. 3. Lay the server on its side for easier operation. 4. The RAID card should be installed into the appropriate PCI Express x8 slot on the system board (callout 31 in Figure 7 “Locating major parts on the system board” on page 34). 5.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation, go to “Completing the parts replacement” on page 122. Then, refer to Chapter 7 “Configuring the server” on page 143 for information about RAID configuration. Installing the ThinkServer 8708EM2 RAID Battery This topic provides information about installing the ThinkServer 8708EM2 RAID Battery (hereafter referred to as the battery card assembly) on the RAID card.
1. Note the top view and bottom view of the battery card assembly. Then, insert the battery pack harness connector into the J4 battery pack harness connector on the backside of the battery card assembly. For more information, refer to the following illustrations. Figure 58. Top view of the battery card assembly 1 Battery pack harness Figure 59. Bottom view of the battery card assembly 1 J4 battery pack harness connector 2 J5 board-to-board connector 3 J2 connector 2.
3. Hold the battery card assembly with the battery side up and the J5 board-to-board connector lining up with the J10 BBU connector 1 on the RAID card. Carefully press the battery card assembly onto the RAID card so that the two connectors are firmly joined. Then, secure the battery card assembly to the RAID card with the three screws and the standoffs that come with the battery card assembly accessory kit. Figure 60.
Figure 61. SAS connectors on the hot-swap hard disk drive backplanes 1 SATA/SAS signal connector 2 3 SATA/SAS signal connector 0 2 SATA/SAS signal connector 3 4 SATA/SAS signal connector 1 When connecting the ThinkServer RAID 500 Adapter to the hot-swap hard disk drive backplanes using the mini SAS cable, connect the mini SAS connector 5 to the RAID card. Connect the four SAS connectors 6 , 7 , 8 , and 9 to the SAS connectors 0, 1, 2, and 3 on the hot-swap hard disk drive backplanes.
Figure 62. Mini SAS cable with four SAS connectors Note: When you are connecting the cables to the corresponding SAS connectors (0-3) on the hot-swap hard disk drive backplanes, follow the sequence indicated by the number on the label on each cable.
To remove the heat sink and fan assembly, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 43. 3. Locate the heat sink and fan assembly. See “Locating server components” on page 32.
• If you have installed a second microprocessor and you are removing the heat sink and fan assembly for microprocessor 2, disconnect the heat sink and fan assembly cable from the system fan 1 connector on the system board. See “Locating parts on the system board” on page 33. Then, remove the four screws 1 that secure the heat sink and fan assembly. Figure 64. Screws that secure the heat sink and fan assembly for microprocessor 2 6. Lift the heat sink and fan assembly off the system board. Notes: a.
8. To install the heat sink and fan assembly, see “Installing the heat sink and fan assembly” on page 99. Installing the heat sink and fan assembly Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39. To obtain a copy of the publications, go to: http://www.lenovo.
4. Touch the static-protective package that contains the heat sink and fan assembly to any unpainted surface on the outside of the server. Then, remove the heat sink and fan assembly from the package. Note: When handling the heat sink and fan assembly, do not touch the thermal grease 1 on the bottom of it. Figure 66.
5. Place the heat sink and fan assembly on the system board so that the four screws on the heat sink and fan assembly are aligned with the corresponding mounting studs on the system board.
This section provides instructions on how to remove a front fan. DANGER Hazardous moving parts. Keep fingers and other body parts away. To remove a front fan, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 43. 3. Locate the front fan that you want to remove.
6. The front fan is attached to the chassis by four rubber mounts 1 . Remove the front fan by cutting the rubber mounts and gently pulling the front fan out of the chassis. Figure 69. Removing the front fan 7. Reinstall all hard disk drives. See “Installing a hot-swap hard disk drive” on page 60 or “Installing a non-hot-swap hard disk drive” on page 68. 8.
DANGER Hazardous moving parts. Keep fingers and other body parts away. To install a front fan, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 43. 3. Remove the hard disk drives.
4. Install the front fan by aligning the four rubber mounts with the corresponding holes in the chassis, and then push the rubber mounts through the holes. Notes: a. The new front fan will have four new rubber mounts attached. b. If two microprocessors are installed in your server, you can install two front fans, one for microprocessor 1 and the other for microprocessor 2. c. You might also need to pull the rubber mounts through the holes from the other side to secure the front fan in place. Figure 70.
Removing the rear fan Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to remove the rear fan. DANGER Hazardous moving parts. Keep fingers and other body parts away.
5. The rear fan is attached to the chassis by four rubber mounts. Remove the rear fan by cutting the rubber mounts and gently pulling the rear fan out of the chassis. Figure 71. Removing the rear fan 6. If you are instructed to return the removed rear fan to the manufacturer, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. 7. To install the rear fan, see “Installing the rear fan” on page 107.
DANGER Hazardous moving parts. Keep fingers and other body parts away. To install the rear fan, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 43.
3. Place the rear fan on the chassis so that the four rubber mounts are aligned with the corresponding holes in the chassis. Then, push the rubber mounts through the holes. Notes: a. The new rear fan will have four new rubber mounts attached. b. You might also need to pull the rubber mounts through the holes from the other side of the chassis to secure the rear fan in place. Figure 72. Installing the rear fan 4. Connect the rear fan cable to the system fan 3 connector on the system board.
Removing the microprocessor Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to remove the microprocessor. CAUTION: The heat sink and fan assembly might be very hot.
Installing the microprocessor Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to install the microprocessor. CAUTION: The heat sink and fan assembly might be very hot.
6. Slightly press the retainer of the microprocessor socket to open it. Figure 75. Opening the retainer 7. Remove the protective cover from the microprocessor socket. To avoid damaging the pins in the microprocessor socket, do not touch the pins while removing the cover. Figure 76. Removing the microprocessor socket cover 8. Remove the new microprocessor from the protective cover that protects the gold contacts on the bottom of the new microprocessor.
9. Hold the new microprocessor by the edges and align the notches 1 on it with the tabs 2 in the microprocessor socket. Then, install the microprocessor into the socket. Figure 77. Installing the microprocessor Replacing the system board battery Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39.
• Heat to more than 100° C (212° F) • Repair or disassemble To replace the system board battery, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 43. 3. Lay the server on its side for easier operation. 4. Locate the system board battery.
This section provides instructions on how to remove the system board. CAUTION: The heat sink and fan assembly might be very hot. Turn off the server and wait three to five minutes to let the server cool before removing the server cover. To remove the system board, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2.
14. The failing system board must be returned with a microprocessor socket cover to protect the pins during shipping and handling. Install the microprocessor socket cover removed from the new system board on the failing system board. To install a microprocessor socket cover: a. Release the lever securing the microprocessor retainer and open the retainer to access the microprocessor. b. Grasp the microprocessor on the sides and lift it straight up and out of the socket.
Installing the system board Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to install a new system board after a failing system board is removed.
Replacing the power supply assembly Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the ThinkServer Documentation DVD that came with your product, and “Guidelines” on page 39. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to replace the power supply assembly.
6. Remove the four screws in the rear of the chassis that secure the power supply assembly and the screw that secures the small metal clip, which holds the power supply assembly in place. Then, remove the metal clip to release the power supply assembly. Figure 82. Removing the screws and the metal clip Chapter 5.
7. Slide the power supply assembly a little bit forward and then remove it from the chassis. Figure 83. Removing the power supply assembly 8. Place the new power supply assembly into the chassis so that the four screw holes in the new power supply assembly are aligned with the corresponding holes in the rear of the chassis.
9. Install the four screws to secure the new power supply assembly and install the metal clip to hold the new power supply assembly in place. Then, install the screw to secure the metal clip. Note: Use only screws provided by Lenovo. Figure 84. Installing the power supply assembly Chapter 5.
10. Properly route the power cables through the holes 1 in the chassis and connect the power cables to all drives, PCI card(s) if necessary, and the system board. Then, secure the power cables to the chassis with cable clips or ties, if necessary. Figure 85. Holes in the chassis for cable routing 11. For server models with hot-swap hard disk drives, connect the power cables to the power connectors on the hot-swap hard disk drive backplanes.
Attention: For proper cooling and airflow, install the server cover before turning on the server. Operating the server for extended periods of time (more than 30 minutes) with the cover removed might damage server components. To install the server cover, do the following: 1. Make sure that all cables, cards, and other components are installed and seated correctly and that you have not left loose tools or parts inside the server. Also, make sure that all internal cables are correctly routed. 2.
If the server has an optional RAID controller and you have installed or removed a hard disk drive, see the documentation that comes with the RAID controller for information about reconfiguring the disk arrays. Turning off the server When you turn off the server and leave it connected to ac power, the server can respond to requests to the service processor, such as a remote request to turn on the server. While the server remains connected to ac power, one or more fans might continue to run.
Chapter 6. Parts listing, TD230 Types 1027, 1029, 1039, and 1040 The following replaceable components are available for the ThinkServer TD230 Types 1027, 1029, 1039, and 1040 servers. To check for an updated parts listing on the Web, do the following: 1. Go to http://www.lenovo.com/support. 2. In the Download & Drivers pane, click ThinkServer. 3. In the Support & downloads pane, click Parts information. 4. Follow the instructions on the Web page to get the latest parts listing for your server.
• Optional-service customer replaceable unit: You may install an optional-service CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server. • Field replaceable unit (FRU): FRUs must be installed only by trained service technicians. For information about the terms of the warranty and getting service and assistance, see the Warranty and Support Information document.
Table 7. Parts listing, Type 1027 (continued) Index Description 6, 10 Microprocessor, Intel Xeon X5670 - 6 Core 2.93 GHz 6.4QPI, 12 MB Cache, DDR3-1333, 95 W (models CTO) 71Y9037 6, 10 Microprocessor, Intel Xeon X5667 - Quad Core 3.06 GHz 6.4QPI, 12 MB Cache, DDR3-1333, 95 W (models CTO) 71Y9039 6, 10 Microprocessor, Intel Xeon E5640 - Quad Core 2.66 GHz - 5.86QPI, 12 MB Cache, DDR3-1066, 80 W (models CTO) 71Y9045 6, 10 Microprocessor, Intel Xeon X5660 - 6 Core 2.80 GHz 6.
Table 7. Parts listing, Type 1027 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) I/O shield (models CTO, all models) 46U3580 Front USB cable (models CTO, all models) 46U3582 5.
Table 7. Parts listing, Type 1027 (continued) Index Description CRU part number (Tier 1) Windows 2008 R2 ENT 64 bit Germany (models CTO) 90Y1194 Windows 2008 R2 ENT 64 bit Italy (models CTO) 90Y1195 Windows 2008 R2 ENT 64 bit Spain (models CTO) 90Y1197 Windows 2008 SBS SP2 PREM 64 bit United Sates (models CTO) 90Y1182 CRU part number (Tier 2) FRU part number 03X3635 ThinkServer RAID 500 Adapter B-2 (Raid 5 Controller) (models CTO) Table 8.
Table 8. Parts listing, Type 1029 (continued) Index Description 6, 10 Microprocessor, Intel Xeon E5506 - Quad Core 2.13 GHz 4.8QPI, 4 MB Cache, DDR3-800, 80 W (models CTO, 11G) 46R6632 6, 10 Microprocessor, Intel Xeon L5609 - Quad Core 1.86 GHz 5.86QPI, 12 MB Cache, DDR3-1333, 40 W (models CTO) 46U3187 6, 10 Microprocessor, Intel Xeon X5670 - 6 Core 2.93 GHz 6.4QPI, 12 MB Cache, DDR3-1333, 95 W (models CTO) 71Y9037 6, 10 Microprocessor, Intel Xeon X5667 - Quad Core 3.06 GHz - 6.
Table 8.
Table 8.
Table 9. Parts listing, Type 1039 (continued) Index Description 4 Hard disk drive, 2 TB SATA - 7200 rpm, 3 Gb/s, 32 MB Cache, 3.5" (models CTO) 46U3400 4 Hard disk drive, 600 GB SAS - 15000 rpm, 3 Gb/s, 32 MB Cache, 3.5" (models CTO) 03X3623 4 Hard disk drive, 2 TB SATA - 7200 rpm, 3 Gb/s, 32 MB Cache, 3.5" (models CTO) 46U3400 4 Hard disk drive, 600 GB SAS - 15000 rpm, 3 Gb/s, 32 MB Cache, 3.
Table 9. Parts listing, Type 1039 (continued) Index Description 6, 10 Microprocessor, Intel Xeon E5672 - 4 Core 3.2 GHz - 6.
Table 9.
Table 10. Parts listing, Type 1040 (continued) Index Description 4 Hard disk drive, 250 GB SATA - 7200 rpm, 3 Gb/s, 8 MB Cache, 3.5" (models CTO) 46U3100 4 Hard disk drive, 500 GB SATA - 7200 rpm, 3 Gb/s, 16MB Cache, 3.5" (models CTO) 46U3101 4 Hard disk drive, 1 TB SATA - 7200 rpm, 3 Gb/s, 32 MB Cache, 3.5" (models CTO) 46U3103 4 Hard disk drive, 300 GB SAS - 15000 rpm, 3 Gb/s, 32 MB Cache, 3.5" (models CTO) 46U3572 4 Hard disk drive, 450 GB SAS - 15000 rpm, 3 Gb/s, 32 MB Cache, 3.
Table 10. Parts listing, Type 1040 (continued) Index Description 6, 10 Microprocessor, Intel Xeon E5607 - Quad Core 2.26 GHz 4.8QPI, 4 MB Cache, DDR3-800, 80 W (models CTO) 03X3647 6, 10 Microprocessor, Intel Xeon E5645 - 6 Core 2.4 GHz 5.86QPI, 12 MB Cache, DDR3-1066, 80 W (models CTO) 03X3648 6, 10 Microprocessor, Intel Xeon E5649 - 6 Core 2.53 GHz 5.86QPI, 12 MB Cache, DDR3-1066, 80 W (models CTO) 03X3649 6, 10 Microprocessor, Intel Xeon E5675 - 6 Core 3.06 GHz 6.
Table 10.
For units intended to be operated at 230 volts (U.S. use): Use a UL-listed and CSA-certified cord set consisting of a minimum 18 AWG, Type SVT or SJT, three-conductor cord, a maximum of 15 feet in length and a tandem blade, grounding-type attachment plug rated 15 amperes, 250 volts. For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a grounding-type attachment plug.
Table 12. Power cords, Type 1029 (continued) Lenovo power cord part number Used in these countries and regions 41R3270 Brazil (models CTO) 41R3278 Taiwan (models CTO) 43N9029 Thailand (models CTO) Table 13.
Table 14. Power cords, Type 1040 (continued) Lenovo power cord part number Used in these countries and regions 41R3278 Taiwan (models CTO) 43N9029 Thailand (models CTO) Chapter 6.
142 ThinkServer TD230 Hardware Maintenance Manual
Chapter 7. Configuring the server The following configuration programs come with the server: • Setup Utility program The Setup Utility program is part of the server firmware. You can use the Setup Utility program to view your server configuration, change the startup device sequence, set the date and time, and set passwords. For information about using this program, see “Using the Setup Utility program” on page 143.
• View, set, and change settings for power-management features • View and clear error logs • Resolve configuration conflicts Starting the Setup Utility program To start the Setup Utility program, do the following: 1. Approximately three minutes after the server is connected to a working electrical outlet, the power button becomes active. Turn on the server and the POST runs automatically. You will then see the logo screen.
Table 16. The Setup Utility program main menu (continued) Item Description Security Set the security parameters. See Table 27 “Items under the Security menu” on page 148. Server Management Set the server system management parameters. See Table 28 “Items under the Server Management menu” on page 148. Boot Options Set the boot parameters. See Table 29 “Items under the Boot Options menu” on page 149.
Table 19. Submenus under the Processor Configuration Item Option Description Enhanced Intel SpeedStep™ Tech Disabled / [Enabled] Enable or disable the SpeedStep technology. Intel Hyper-Threading Tech Disabled / [Enabled] Enable or disable the hyper-thread technology. (Whether your server supports this feature or not is depending on the type of the installed microprocessor.) Core Multi-Processing Disabled / [Enabled] Enable or disable the multi-core processing function.
Table 21. Submenus under the Memory RAS and Performance Configuration Item Option Select Memory RAS Configuration NUMA Optimized Description Select the RAS configuration for installed memory modules. Disabled / [Enabled] Whether the BIOS contains the ACPI configuration form required by NUMA OS. Note: The settings in [ ] are the default settings in the Setup Utility program. Table 22.
Table 25. Submenus under the PCI Configuration Item Option Maximize Memory below 4 GB [Disabled] / Enabled Memory Mapped I/O above 4 GB [Disabled] / Enabled Onboard Video [Enabled] / Disabled Dual Monitor Video [Disabled] / Enabled (If enable this option, the system can support the add-in graphics card.
Table 28. Items under the Server Management menu (continued) Item Option Description FRB-2 Enable [Disabled] / Enabled OS Boot Watchdog Timer [Disabled] / Enabled OS Boot Watchdog Timer Policy [power off] Default. Cannot be modified. OS Boot Watchdog Timer Timeout [10 minutes] Default. Cannot be modified. Plug & Play BMC Detection [Disabled] / Enabled ACPI 1.0 Support [Disabled] / Enabled Console Redirection [Disabled] / Serial Port A / Serial Port B View the system information.
Password considerations A password can be any combination of up to 7 (1 to 7) alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised. To set a strong password, use the following guidelines: Note: The Setup Utility program passwords are not case sensitive.
Table 30. RAID utilities (continued) RAID configuration utility Description Where to find more information Location configured Lenovo servers.
Before you use the EasyStartup DVD Functionality and supported operating systems can vary with different versions of the EasyStartup program. To learn more about the version you have, do the following: 1. Insert the ThinkServer EasyStartup DVD and restart the server. 2. Advance to the Home screen. 3. Click Compatability notes.
Configuring RAID The RAID configuration feature that is part of the EasyStartup program enables you to view and change RAID settings for supported RAID controllers. Through this feature, you have the ability to configure each installed controller.
1. Online This status indicates the normal operation of the RAID array. 2. Degrade This status indicates that more than one hard disk drive is faulty or disconnected from mirror volume and you have to replace the faulty hard disk drives and recover the data through the Rebuild function. 3. Offline This status indicates that the RAID array is failed and unable to be restored by rebuilding. You have to create the array again.
4. After you finish selecting the physical drives, press Enter or F10. The array selection window opens. Press the space key to select the array. 5. Press F10, the Virtual Drive(s) Configured window opens. The following table is an example about the information on this window. Virtual Drive(s) Configured VD RAID Size #Stripes StripSz Status 0 0 73664 MB 1 64 KB ONLINE 6. Select RAID on the Virtual Drive(s) Configured window and press Enter. The RAID array selection menu opens. 7.
3. Follow the instructions on the screen to select the RAID volume. 4. Select Yes and press Enter to delete the RAID volume. Rebuilding the RAID volume When there is a failing hard disk drive in the volume, you need to replace the hard disk drive. You can restore the RAID volume through the rebuilding function. To rebuild the RAID volume, do the following: 1. Do one of the following: • Select Management ➙ Rebuild from the main menu. The hard disk drive selection window opens.
Figure 86. SATA connectors on the system board and SATA/SAS connectors on the hot-swap hard disk drive backplanes Notes: 1. The following table shows the sequence to follow when you are connecting the hot-swap hard disk drive backplanes to the system board using the SATA cable(s).
Updating the firmware The firmware in the server is periodically updated and is available for download on the Lenovo Support Web site. Go to http://www.lenovo.com/support to check for the latest level of firmware, such as the BIOS ROM file, BMC FW and RAID FW files. When you replace a device in the server, you might have to either update the server with the latest version of the firmware that is stored in memory on the device or restore the pre-existing firmware from a diskette or CD image.
Also, the ThinkServer EasyStartup program provides an option to install the ThinkServer EasyManage Agent as part of the operating system installation process. Chapter 7.
160 ThinkServer TD230 Hardware Maintenance Manual
Appendix A. RAID battery card assembly Specifications The following table provides specifications of the ThinkServer 8708EM2 RAID Battery. Battery technology LiON Battery operating temperature (ambient) 10 to 40°C (50 to 104°F) Humidity (storage and operating) 20%-80% (non-condensing) (ThinkServer 8708EM2 RAID Battery) Battery storage temperature • < 30 days: 0 to 50°C (32 to 122°F) • 30-90 days: 0 to 40°C (32 to 104°F) • > 90 days: 0 to 30°C (32 to 86°F) Battery voltage conditioning <3.
162 ThinkServer TD230 Hardware Maintenance Manual
Appendix B. Getting help and technical assistance If you need help, service, or technical assistance or just want more information about Lenovo products, you will find a wide variety of sources available from Lenovo to assist you. This section contains information about where to go for additional information about Lenovo and Lenovo products, what to do if you experience a problem with your system, and whom to call for service, if it is necessary.
• Problem determination - Trained personnel are available to assist you with determining a hardware problem and deciding what action is necessary to fix the problem. • Hardware repair - If the problem is caused by hardware under warranty, trained service personnel are available to provide the applicable level of service. • Engineering Change management - There might be changes that are required after a product has been sold.
For technical assistance with the installation of, or questions related to, Service Packs for your preinstalled Microsoft Windows product, refer to the Microsoft Product Support Services Web site at http://www.support.microsoft.com/directory/, or you can contact the Customer Support Center. Some fees might apply.
166 ThinkServer TD230 Hardware Maintenance Manual
Appendix C. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks Lenovo, the Lenovo logo, and ThinkServer are trademarks of Lenovo in the United States, other countries, or both. Intel and Intel Xeon are trademarks of Intel Corporation in the United States, other countries, or both. Microsoft and Windows are trademarks of the Microsoft group of companies. Linux is a trademark of Linus Torvalds in the United States, other countries, or both. Red Hat and all Red Hat-based trademarks and logos are trademarks or registered trademarks of Red Hat, Inc.
responsablemente sus equipos cuando éstos ya no les sean útiles. Lenovo dispone de una serie de programas y servicios de devolución de productos, a fin de ayudar a los propietarios de equipos a reciclar sus productos de TI. Se puede encontrar información sobre las ofertas de reciclado de productos de Lenovo en el sitio web de Lenovo http://www.lenovo.com/lenovo/environment/recycling. Notice: This mark applies only to countries within the European Union (EU) and Norway.
or replacement of servers or parts on implementation of appropriate remedial measures to mitigate such environmental contamination. Implementation of such remedial measures is a customer responsibility. Table 31. Limits for particulates and gases Contaminant Limits Particulate • The room air must be continuously filtered with 40% atmospheric dust spot efficiency (MERV 9) according to ASHRAE Standard 52.21. • Air that enters a data center must be filtered to 99.
US & Canada Only For Taiwan: Please recycle batteries. For the European Union: Notice: This mark applies only to countries within the European Union (EU). Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union.
and accumulators on the environment and human health due to the potential presence of hazardous substances. For proper collection and treatment, go to http://www.lenovo.com/lenovo/environment. For California: Perchlorate material - special handling may apply. See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/. The foregoing notice is provided in accordance with California Code of Regulations Title 22, Division 4.5 Chapter 33. Best Management Practices for Perchlorate Materials.
This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to European Standard EN 55022. The limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment. Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Störungen zu erwarten sind.” (Auszug aus dem EMVG, Paragraph 3, Abs. 4). Dieses Genehmigungsverfahren ist nach Paragraph 9 EMVG in Verbindung mit der entsprechenden Kostenverordnung (Amtsblatt 14/93) kostenpflichtig. Anmerkung: Um die Einhaltung des EMVG sicherzustellen sind die Geräte, wie in den Handbüchern angegeben, zu installieren und zu betreiben.
Index A assistance, getting availability 12 E 163 B backplane locating connectors basic guidelines 39 bays 12 37 C cables rear connectors 123 Class A electronic emission notice 172 configuration 123 Ethernet controller 157 minimum 25 updating server 143 Configuration Utility program ThinkServer RAID 500 Adapter 143 connector cables 123 connectors rear of the server 30 considerations, password 150 contamination, particulate and gaseous 170 controller Ethernet, configuring 157 controller, configuring Ethe
H hard disk drive problems 16 hard disk drives hot-swap SAS or SATA, installing 60 hot-swap SAS or SATA, removing 57 non-hot-swap SAS or SATA, installing 68 non-hot-swap SAS or SATA, removing 65 heat sink and fan assembly installing 99 removing 96 help, getting 163 hot-swap drives, SAS or SATA removing 57 hot-swap hard disk drive backplanes 37 hot-swap hard disk drive, SAS or SATA installing 60 I installation order memory module 49 installation rules memory module 49 installing DIMM 50 Ethernet card 75 fro
CD-ROM, DVD-ROM drive DIMM 17 Ethernet controller 24 general 16 hard disk drive 16 intermittent 16 memory 17 microprocessor 18 monitor 19 mouse 17 optional devices 20 power 21, 23 serial port 22 software 23 undetermined 24 USB port 23 15 R RAID 5 key installing 77 removing 78 RAID card installing 89–90 removing 88 RAS features 12 rear fan installing 107 removing 106 rear view 30 reliability 12 removing DIMM 51 Ethernet card 76 front fan 101 heat sink and fan assembly 96 hot-swap hard disk drive 57 hot-swa
U undetermined problems 24 United States electronic emission Class A notice United States FCC Class A notice 172 Universal Serial Bus (USB) problems 23 updating server configuration 143 updating firmware 158 updating the server configuration 123 USB port problems 23 using EasyStartup 151 passwords 149 Setup Utility program 143 172 V video problems 19 video controller, integrated specifications 12 W Web site compatible options 49 Lenovo support 39 publication ordering 163 support 163 working inside the se
Part Number: Printed in China (1P) P/N: **
