User Guide ThinkPad Edge S430
Notes: Before using this information and the product it supports, be sure to read and understand the following: • Safety, Warranty, and Setup Guide • Regulatory Notice • “Important safety information” on page vi • Appendix D “Notices” on page 143 The Safety, Warranty, and Setup Guide and the Regulatory Notice have been uploaded to the Web site. To refer to them, go to http://www.lenovo.com/ThinkPadUserGuides and click User Guides & Manuals, then follow the instructions on the screen.
Contents Read this first . . . . . . . . . . . . . . v Important safety information . . . . . . . . . . vi Conditions that require immediate action . . vii Safety guidelines . . . . . . . . . . . . vii Chapter 1. Product overview . . . . . . 1 Locating computer controls, connectors, and indicators. . . . . . . . . . . . . . . Front view. . . . . . . . . . . . . Right-side view. . . . . . . . . . . Left-side view . . . . . . . . . . . Bottom view . . . . . . . . . . . . Rear view . . . . . . . . . . . . .
Chapter 6. Replacing devices . . . . . Static electricity prevention . . . . . . . . . Disabling the built-in battery . . . . . . . . Replacing the SIM card . . . . . . . . . . Replacing the hard disk drive or solid state drive Replacing the keyboard . . . . . . . . . . Replacing the optical drive . . . . . . . . . Replacing a memory module . . . . . . . . Replacing a Mini PCI ExpressCard for wireless LAN connection . . . . . . . . . . . . . Replacing a Mini PCI ExpressCard for wireless WAN connection . . .
Battery recycling information for Taiwan . . . . . Battery recycling information for the United States and Canada . . . . . . . . . . . . . . . . Appendix C. ENERGY STAR model information . . . . . . . . . . . . . © Copyright Lenovo 2012 139 Appendix D. Notices. . . . . . . . . Trademarks . . . . . . . . . . . . . . . .
iv User Guide
Read this first Be sure to follow the important tips given here to get the most use and enjoyment out of your computer. Failure to do so might lead to discomfort or injury, or cause your computer to fail. Protect yourself from the heat that your computer generates. When your computer is turned on or the battery is charging, the base, the palm rest, and some other parts may become hot. The temperature they reach depends on the amount of system activity and the level of charge in the battery.
Protect your computer and data when moving it. Before moving a computer equipped with a hard disk drive, do one of the following, and ensure that the power button is off or is blinking: • Turn it off. • Put it in sleep mode. • Put it in hibernation mode. This will help to prevent damage to the computer, and possible loss of data. Handle your computer gently. Do not drop, bump, scratch, twist, hit, vibrate, push, or place heavy objects on your computer, display, or external devices.
Conditions that require immediate action Products can become damaged due to misuse or neglect. Some product damage is serious enough that the product should not be used again until it has been inspected and, if necessary, repaired by an authorized servicer. As with any electronic device, pay close attention to the product when it is turned on. On very rare occasions, you might notice an odor or see a puff of smoke or sparks vent from your product. Or you might hear sounds like popping, cracking or hissing.
that the power is turned off and that the product is unplugged from any power source. If you have any questions or concerns, contact the Customer Support Center. Although there are no moving parts in your computer after the power cord has been disconnected, the following warnings are required for your safety. CAUTION: Hazardous moving parts. Keep fingers and other body parts away.
Power cords and power adapters DANGER Use only the power cords and power adapters supplied by the product manufacturer. The power cords shall be safety approved. For Germany, it shall be H05VV-F, 3G, 0.75 mm2, or better. For other countries, the suitable types shall be used accordingly. Never wrap a power cord around a power adapter or other object. Doing so can stress the cord in ways that can cause the cord to fray, crack, or crimp. This can present a safety hazard.
Plugs and outlets DANGER If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician. Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement.
General battery notice DANGER Personal computers manufactured by Lenovo contain a coin cell battery to provide power to the system clock. In addition, many mobile products, such as notebook computers, utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts. Never attempt to open or service any battery.
Lithium coin cell battery notice DANGER Danger of explosion if battery is incorrectly replaced. When replacing the lithium coin cell battery, use only the same or an equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations.
Heat and product ventilation DANGER Computers, ac power adapters, and many accessories can generate heat when turned on and when batteries are charging. Notebook computers can generate a significant amount of heat due to their compact size. Always follow these basic precautions: • When your computer is turned on or the battery is charging, the base, the palm rest, and some other parts may become hot.
Electrical current safety information DANGER Electric current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not use your computer during a lightning storm. • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. • Connect all power cords to a properly wired and grounded electrical outlet. • Connect to properly wired outlets any equipment that will be attached to this product.
DANGER Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following. Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Liquid crystal display (LCD) notice CAUTION: The liquid crystal display (LCD) is made of glass, and rough handling or dropping the computer can cause the LCD to break.
Many personal computer products and accessories contain cords, cables or wires, such as power cords or cords to connect the accessory to a personal computer. If this product has such a cord, cable or wire, then the following warning applies: WARNING: Handling the cord on this product or cords associated with accessories sold with this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
Chapter 1. Product overview This chapter provides information about the locations of connectors, locations of important product labels, computer features, specifications, operating environment, and preinstalled ThinkVantage® programs.
7 TrackPoint® pointing stick 8 Fingerprint reader 9 TrackPoint buttons 10 Touch pad 11 Mini PCI ExpressCard slot for wireless LAN card 13 Volume control keys 12 Mini PCI ExpressCard slot for wireless WAN card or mSATA solid state drive 14 Power button 15 Built-in stereo speaker (left) 1 Built-in microphones The built-in microphones capture sound and voice when used with an application program capable of handling audio. 2 Integrated camera Use the camera to take pictures or hold a video conference.
11 Mini PCI ExpressCard slot for wireless LAN card Your computer might include a wireless local area network (LAN) card in the Mini PCI ExpressCard slot for you to establish wireless LAN connections. 12 Mini PCI ExpressCard slot for wireless WAN card or mSATA solid state drive Your computer might have a wireless wide area network (WAN) card installed in the Mini PCI ExpressCard slot for wireless WAN connections.
Note: Your computer keyboard might look different from the illustration above. 1 Mini DisplayPort connector or Thunderbolt connector (depending on the model) 2 Mini High Definition Multimedia Interface (HDMI) port 3 USB 3.
5 Fan louver The internal fan and louvers enable air to circulate in the computer and cool the central processor. Note: To avoid impeding airflow, do not place any obstacle in front of the fan. 6 Security keyhole Purchase a security cable lock that fits this keyhole to lock your computer to a stationary object to protect your computer from theft. Left-side view Figure 3. ThinkPad Edge S430 left-side view Note: Your computer keyboard might look different from the illustration above.
• Secure Digital eXtended-Capacity (SDXC) card • MultiMediaCard (MMC) 4 USB 3.0 connector The USB 3.0 connector is used for connecting devices compatible with a USB interface, such as a USB printer or a digital camera. Notes: • When you attach a USB cable to the connector, ensure that the USB mark is facing upward. Otherwise the connector might be damaged. • The USB 3.0 function only works in the Windows 7 operating system.
1 Fan louver The internal fan and louvers enable air to circulate in the computer and cool the central processor. Note: To avoid impeding airflow, do not place any obstacle in front of the fan. 2 Emergency reset hole If the computer does not respond, remove the ac power adapter and reset the computer by inserting a straightened paper clip into the emergency reset hole to turn off the computer. 3 Integrated battery Use your computer with the battery power whenever ac power is unavailable.
System status indicators The illuminated dot in the ThinkPad logo on the outer lid of your computer and on the palm rest works as a system status indicator. Note: Your computer keyboard might look different from the illustration above. The meaning of the indicator is as follows: • Red: The computer is on (in normal mode). • Fast blinking red: The computer is entering hibernation mode. • Slow blinking red: The computer is in sleep mode. • Off: The computer is off or in hibernation mode.
Note: Your computer keyboard might look different from the illustration above. The meaning of the indicator is as follows: • Green: The ac power adapter is connected. • Off: The ac power adapter is not connected. Locating important product information This section provides information to help you locate your machine type and model label, FCC ID and IC Certification label, and the Windows® Certificate of Authenticity (COA) label.
FCC ID and IC Certification number label There is no FCC ID or IC Certification number for the PCI Express Mini Card shown on the enclosure of your computer. The FCC ID and IC Certification number label is affixed on the card installed in the PCI Express Mini Card slot of your computer. If you need to remove the Wireless LAN card for repair or replacement, follow the procedure in “Replacing a Mini PCI ExpressCard for wireless LAN connection” on page 75.
The Certificate of Authenticity label of your computer is shown as below: Features This topic lists the features of your computer. Processor See the system properties of your computer. To view the system properties of your computer, click Start, right-click Computer; then select Properties. Memory Double data rate 3 synchronous dynamic random access memory modules (DDR3 SDRAM) Storage device • 2.5-inch (7 mm height) hard disk drive • 2.5-inch (9.
• Fn key • Volume control keys • Speaker mute key • Microphone mute key Interface • Mini HDMI port • Mini DisplayPort connector (on some models) • Thunderbolt connector (on some models) • Combo audio jack • USB 3.
Lithium-ion (Li-Ion) battery pack Battery life • For percentage of the remaining battery power, see the Power Manager battery gauge on the taskbar. • The Power Manager program also displays a green, yellow, or red indication. A battery under warranty with a red indication is eligible for a warranty replacement. Operating environment This section provides information about your computer operating environment.
Click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools. Double-click a program icon to access the program. Note: If a program icon in the Lenovo ThinkVantage Tools program navigation window is dimmed, it indicates that you need to install the program manually. To install the program manually, double-click the program icon. Then, follow the instructions on the screen. When the installation process completes, the program icon will be activated. Table 1.
Table 2.
Communications Utility Use the ThinkVantage Communications Utility program to configure settings for the integrated camera and audio devices. Fingerprint Software If your system comes with a fingerprint reader, the Fingerprint Software program enables you to enroll your fingerprint and associate it with your Windows password. As a result, the fingerprint authentication can replace your password and enable simple and secure user access.
SimpleTap The SimpleTap program provides you with a quick way to customize some basic computer settings such as muting the speakers, adjusting the volume, locking the computer operating system, launching a program, opening a Web page, opening a file, and so on. You also can use the SimpleTap program to access the Lenovo App Shop, from which you can download various applications and computer software. To start the SimpleTap program in a quick way, click the red SimpleTap launch point on the desktop.
18 User Guide
Chapter 2. Using your computer This chapter provides information on using some of the computer components.
How to use the battery power more effectively? • To conserve power, or to suspend operation without exiting applications or saving files, see “Power-saving modes” on page 28. • To achieve the best balance between performance and power saving, create and apply power plans by use of the Power Manager program. • If your computer will be turned off for an extended period of time, you can prevent battery power from draining by removing the battery.
Special keys Your computer has several special keys 1 and figure shows the locations of the special keys. 2 to help you work more easily and effectively. The following You can toggle the F1-F12 key functionality to use the keys in default mode or in legacy mode. In default mode, you can initiate the special functions illustrated on each key by pressing the corresponding key directly.
• Speaker volume down (F2) Press this key to turn down the volume of your computer. • Speaker volume up (F3) Press this key to turn up the volume of your computer. • Microphone mute (F4) Press this key to mute or unmute all of the recording devices. • Launching the camera and audio settings (F5) Press this key to open the camera and audio settings window. The camera preview is turned on. Change the camera and audio settings as desired.
Windows key Press the Windows key 2 to display or hide the Start menu of the Windows operating system. For information about using the Windows key with other keys, refer to the help information system of the Windows operating system. Other functions • Fn+Spacebar: Enables or disables the ThinkLight light. • Fn+B: Has the same function as the Break key on a conventional keyboard. • Fn+P: Has the same function as the Pause key on a conventional keyboard.
The TrackPoint center button 3 , called the scroll bar, enables you to scroll Web pages or documents in any direction with no need to use the graphic scroll bars on the side of the window. Note: Your computer keyboard might look slightly different from the illustration above. If you are not familiar with the TrackPoint pointing device, these instructions will help you get started: 1.
Note: If you replace the keyboard, a new keyboard is shipped with the default cap. If you wish, you can keep the cap from your old keyboard and use it on the new one. Using the touch pad The touch pad is a pad 1 below the TrackPoint buttons at the bottom of the keyboard. To move the pointer 2 on the screen, slide your fingertip over the pad in the direction in which you want the pointer to move. Note: Your computer keyboard might look slightly different from the illustration above.
Disabling the UltraNav pointing device and using an external mouse If you attach an external mouse to a USB connector, you can use the external mouse simultaneously with the TrackPoint pointing device and the touch pad. Disabling the TrackPoint or the touch pad If you want to disable the TrackPoint or the touch pad, do the following: 1. Click Start ➙ Control Panel ➙ Hardware and Sound ➙ Mouse ➙ UltraNav. 2. To disable the TrackPoint pointing device, clear the check box for Enable TrackPoint.
Using the ac power adapter The power to run your computer can come either from the lithium-ion (Li-ion) battery pack provided with it, or from ac power through the ac power adapter. While you use ac power, the battery charges automatically. The ac power adapter that comes with your computer has two basic components: • The transformer pack that converts ac power adapter for use with the computer. • The power cord that plugs into the ac outlet and into the transformer pack.
• Recharge the battery completely before using it. The battery is fully charged if the battery indicator shows green. • Always use power management features such as power modes, screen blank, sleep, and hibernation. Managing the battery power With Power Manager, you can adjust your power settings to give you the best balance between performance and power saving. For instructions on accessing the Power Manager program, see “Accessing ThinkVantage programs on the Windows 7 operating system” on page 13.
Enabling the wakeup function If you put your computer into hibernation mode, and the wakeup function is disabled (this is the default setting), the computer does not consume any power. If the wakeup function is enabled, it consumes a small amount of power. To enable the function, do the following: 1. Click Start ➙ Control Panel ➙ System and Security. 2. Click Administrative Tools. 3. Double-click Task Scheduler.
Wireless connections Wireless connection is the transfer of data without the use of cables by means of radio waves only. Depending on the frequency used for data transmission, the area covered, or the type of the device used for data transfer, the following categories of wireless networks might be available to you: Wireless LAN A wireless LAN covers a relatively small geographic area, such as an office building or a house. Devices based on the 802.11 standards can connect to this network.
Access Connections, a connectivity assistant program, can easily enable one network card and disable the other cards on demand. After setting up your wireless networking connection, you can use the program to quickly switch the network settings. Establishing wireless WAN connections Wireless Wide Area Network (wireless WAN) enables you to establish wireless connections over remote public or private networks.
You can find more detailed information about the signal strength and status of your wireless connection by opening the Access Connections program or by right-clicking the Access Connections gauge on the taskbar and selecting View Status of Wireless Connection. • Access Connections gauge states: wireless LAN Power to the wireless radio is off or no signal. – – Power to the wireless radio is on. The signal strength of the wireless connection is poor.
– Power to the wireless radio is on. The signal strength of the wireless connection is poor. To improve signal strength, move your system closer to the wireless access point. • Wireless status icon states: wireless WAN – Power to the WAN radio is off – No association – No signal – Signal level 1 – Signal level 2 – Signal level 3 Note: If you have trouble in making a connection, try moving your computer closer to your wireless access point.
3. Change the display output location by pressing F6. This enables you to switch between viewing output on the external monitor, the computer monitor, and both monitors. Notes: • If the monitor connector is not compatible with the Mini DisplayPort connector or Thunderbolt connector on your computer, you can use a convert cable to establish the connection. Convert cables are available as options from Lenovo at http://www.lenovo.com/accessories/services/index.html.
Changing display settings You can change the display settings, such as the display resolution, font size, and so on. To change the display settings, do the following: 1. Open Control Panel and click Appearance and Personalization. 2. Click Display for further configuration. Using the Extend desktop function Your computer supports a function named the Extend desktop. With the Extend desktop function, you can display output on both the computer display and an external monitor.
5. Set the resolution for the secondary display. 6. Click OK to apply the changes. Note: To change the color settings, right-click on the desktop, and click Screen resolution. Click Advanced Settings, select the Monitor tab, then set Colors. Setting up a presentation To make presentations, you can attach a projector to your computer through the Mini DisplayPort connector or the Thunderbolt connector on your computer.
Note: The combo audio jack does not support a conventional microphone. The following table shows which functions of the audio devices attached to the jacks on your computer are supported. Table 3. Audio feature list Jack Headset with a 3.
Note: Avoid using your computer in dark conditions for prolonged periods. It is bad for your eyes. Using the optical drive Note: Your computer only supports the MultiBurner drive. MultiBurner drive This drive can read DVD-ROM discs, DVD-R discs, DVD-RAM discs, DVD-RW discs, and all types of CDs, such as CD-ROM discs, CD-RW discs, CD-R discs, and audio CDs. In addition, it can record on DVD-R discs, DVD-RW discs, type II DVD-RAM discs, CD-RW standard and high speed discs, and CD-R discs.
• Do not remove the card while the computer is in sleep mode or hibernation mode. Otherwise, the system might not respond when you try to resume operation. To remove a media card, do the following: 1. Click Show hidden icons on the taskbar. 2. Right-click the Safely Remove Hardware and Eject Media icon. 3. Select the corresponding item to eject the card from the Windows operating system. 4. Press the card to eject it from your computer. 5.
40 User Guide
Chapter 3. You and your computer This chapter provides information about accessibility, comfort, and travelling with your computer. • “Accessibility and comfort” on page 41 • “Traveling with your computer” on page 43 Accessibility and comfort Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort. Arrange your workplace and the equipment you use to suit your individual needs and the kind of work that you perform.
Display: Position the display to maintain a comfortable viewing distance of 20-30 inches (510-760 mm). Avoid glare or reflections on the display from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness to levels that enable you to see the screen clearly. Press F7 or F8 to adjust display brightness. Head position: Keep your head and neck in a comfortable and neutral (vertical, or upright) position.
Assistive technologies enable users to access information in the most appropriate way. Some of these technologies are already provided in your operating system. Others can be purchased through vendors, or accessed through the World Wide Web http://www.lenovo.com/healthycomputing. Assistive technologies Some accessibility technologies are available through the Accessibility Options program. Depending on your operating system, the number of accessibility options available varies.
• When taking off, remember to turn off your computer or put it into hibernation mode.
Chapter 4. Security This chapter provides information about how to protect your computer from theft and unauthorized use.
1. Press F1. The icon changes to this: 2. Type the master hard disk password. Note: To return to the icon , press F1 again. If this icon is displayed, type a supervisor password. Note: Press the Backspace key if you enter a wrong password while you are typing your password. Power-on password You can set a power-on password to help protect your computer against access by unauthorized users. If you set a power-on password, the password prompt is displayed on the screen whenever you turn on the computer.
If a user hard disk password has been set, but no master hard disk password has been, the user must enter the user hard disk password in order to gain access to files and applications on the hard disk drive. The master password can be set and used only by a system administrator. Like a master key, it enables the administrator to get access to any hard disk drive in a system. The administrator sets the master password; no one else knows it.
9. In the Setup Notice window that is displayed, press Enter to continue. 10. Press Fn+F10. The Setup Confirmation window opens. Select Yes to save configuration changes and exit. The next time you turn on your computer, you will have to type the user or master hard disk password in order to start your computer and get access to your operating system.
• The system administrator can use the supervisor password to get access to a computer even if the user of that computer has set a power-on password. The supervisor password overrides the power-on password.
• To set a password, do the following: a. In the Enter New Password field, type a desired password and press Enter. b. In the Confirm New Password field, retype the password and press Enter. • To change a password, do the following: a. In the Enter Current Password field, type the current supervisor password and press Enter. b. In the Enter New Password field, type the new supervisor password; then retype the password you just entered to verify it in the Confirm New Password field. Press Enter.
system and data stored on your computer, even if your computer is lost or stolen. BitLocker works by encrypting all user and system files, including the swap and hibernation files. BitLocker uses a Trusted Platform Module to provide enhanced protection for your data and to ensure early boot component integrity. A compatible TPM is defined as a V1.2 TPM.
2. Save all open files, and exit all applications. 3. Turn your computer off and then turn it on again. 4. When the logo screen is displayed, press F1. The ThinkPad Setup program main menu opens. 5. Using the cursor keys, move to Security. The Security menu opens. 6. Using the cursor keys, move to Security Chip, and press Enter. The Security Chip submenu opens. 7. Using the cursor keys, move to an item you want to set. When the item is highlighted, press Enter. 8. Set other items that you want to set. 9.
1. Place the ball of your finger (the central part of the fingerprint) on the small circle above the reader. Ensure that the entire top joint of the finger is on the reader. Note: Your computer keyboard might look different from the illustration above. 2. Apply light pressure and swipe your finger across the reader in one smooth motion. Note: Your computer keyboard might look different from the illustration above.
• The surface of the reader is dirty or stained. • The surface of the reader is wet. • The reader often fails to enroll or authenticate your fingerprint. If your finger has any of the following conditions, you might not be able to register or authenticate it: • Your finger is wrinkled. • Your finger is rough, dry, or injured. • Your finger is stained with dirt, mud, or oil. • The surface of your finger is very different from when you enrolled your fingerprint. • Your finger is wet.
Note: Running either application will take a couple of hours. Using firewalls If your system is preinstalled with a firewall program, it protects against computer Internet security threats, unauthorized access, intrusions, and Internet attacks. It also protects your privacy. For more information about how to use the firewall program, refer to the help information system that comes with the program.
56 User Guide
Chapter 5. Recovery overview This chapter provides information about the recovery solutions provided by Lenovo. • “Creating and using a recovery media” on page 57 • “Performing backup and recovery operations” on page 58 • “Using the OneKey Recovery Pro workspace” on page 59 • “Creating and using a rescue medium” on page 60 • “Reinstalling preinstalled applications and device drivers” on page 61 • “Solving recovery problems” on page 62 Notes: 1.
Note: You can create recovery media using discs or external USB storage devices. To create recovery media, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Factory Recovery Disks. Then, follow the instructions on the screen. Using recovery media This section provides instructions on how to use recovery media on different operating systems. • You can use recovery media to restore the computer to the factory default settings only.
3. Click Back up your hard drive and select backup operation options. Then, follow the instructions on the screen to complete the backup operation. Performing a recovery operation This section provides instructions on how to perform a recovery operation using the OneKey Recovery Pro program. 1. From the Windows desktop, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Enhanced Backup and Restore. The OneKey Recovery Pro program opens. 2.
3. If you have set a OneKey Recovery Pro password, type your password when prompted. The OneKey Recovery Pro workspace opens after a short delay. Note: If the OneKey Recovery Pro workspace fails to open, see “Solving recovery problems” on page 62. 4. Do one of the following: • To rescue files from your hard disk drive or from a backup, click Rescue files and follow the instructions on the screen.
• If you have created a rescue medium using a USB hard disk drive, use the following instructions to use the rescue medium: 1. Attach the USB hard disk drive to one of the USB connectors on your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Boot Menu window opens, release the F12 key. 3. In the Boot Menu window, select the USB hard disk drive as the first boot device and press Enter. The rescue medium starts.
Solving recovery problems If you are unable to access the OneKey Recovery Pro workspace or the Windows environment, do one of the following: • Use a rescue medium to start the OneKey Recovery Pro workspace. See “Creating and using a rescue medium” on page 60. • Use recovery media if all other methods of recovery have failed and you need to restore the hard disk drive to the factory default settings. See “Creating and using a recovery media” on page 57.
Chapter 6. Replacing devices This chapter provides instructions on how to install or replace hardware for your computer.
Replacing the SIM card Before you start, print these instructions. Your computer might require a SIM card to establish wireless WAN connections. Depending on the country of delivery, you might need to purchase a SIM card , or a SIM card might already be installed in your computer, or the SIM card is part of the shipping contents that come with your computer. If you find a SIM card included in the shipping contents, a dummy card is installed in the SIM card slot. Then proceed with the following instructions.
5. Hold the new card with the metal contact facing downwards. Then, insert the card firmly into the slot until you hear a click. 6. Close the SIM card door until it snaps into position. 7. Turn the computer over again. Connect the ac power adapter and all cables. Replacing the hard disk drive or solid state drive Before you start, print these instructions. Attention: The hard disk drive is very sensitive. Incorrect handling can cause damage and permanent loss of data.
• Before removing the hard disk drive or solid state drive, make a backup copy of all the information on it, and then turn the computer off. • Never remove the hard disk drive or solid state drive while the computer is operating, in sleep mode, or in hibernation mode. To replace the hard disk drive or solid state drive, do the following: 1. Disable the built-in battery. See “Disabling the built-in battery” on page 63. 2. Close the computer display, and turn the computer over. 3.
5. Insert the hard disk drive or solid state drive into the slot and slide the hard disk drive or solid state drive firmly into place. 6. Reinstall the hard disk drive or solid state drive door 1 . Then tighten the screw 2 . 7. Turn the computer over again. Connect the ac power adapter and all cables. Replacing the keyboard Before you start, print these instructions. DANGER During electrical storms, do not connect the cable to or disconnect it from the telephone outlet on the wall.
To remove the keyboard, do the following: 1. Disable the built-in battery. See “Disabling the built-in battery” on page 63. 2. Close the computer display, and turn the computer over. 3. Remove the two screws that secure the keyboard at the bottom. 4. Turn the computer over and open the display. 5. Push hard in the direction shown by the arrows keyboard will be detached slightly. 1 to unlatch the front side of the keyboard.
6. Remove the cables 2 and 4 by flipping the connectors 1 and 3 upwards. Remove the keyboard. Note: Your computer keyboard might look different from the illustration above. To install the keyboard, do the following: 1. Attach the cables 1 and 3 by flipping the connectors 2 and 4 downwards. Note: Your computer keyboard might look different from the illustration above. Chapter 6.
2. Insert the keyboard. Ensure that the rear edge of the keyboard is under the frame. Note: Your computer keyboard might look different from the illustration above. 3. Slide the keyboard into place in the direction shown by the arrows. Note: Your computer keyboard might look different from the illustration above.
4. Close the computer display and turn the computer over. Reinstall the two screws at the bottom. 5. Turn the computer over again. Connect the ac power adapter and all cables. Replacing the optical drive Before you start, print these instructions. An optical drive is preinstalled in the optical drive bay. If it needs to be repaired, remove it by doing the following: 1. Disable the built-in battery. See “Disabling the built-in battery” on page 63. 2. Close the computer display, and turn the computer over.
5. Press the edge of the optical drive outwards using the tip of a thin screwdriver as shown, and pull out the optical drive. To install a new optical drive, do the following: 1. Insert the optical drive into the optical drive bay, and then press it firmly into the connector.
2. Tighten the screw that secures the optical drive. 3. Reinstall the keyboard. See “Replacing the keyboard” on page 67. 4. Turn the computer over again. Connect the ac power adapter and all cables. Replacing a memory module Before you start, print these instructions. Increasing memory capacity is an effective way to make programs run faster. To replace or add a memory module, read the following prerequisites, and then the instructions. When replacing a memory module, be sure to follow the precautions.
4. If the memory module already is in the memory slot, press out on the latches on both edges of the socket at the same time 1 , and then remove the memory module 2 . Save the removed memory module for future use. 5. Find the notch on the contact edge side of the memory module you are installing. Attention: To avoid damaging the memory module, do not touch its contact edge. 6.
9. Turn the computer over again. Connect the ac power adapter and all cables. Replacing a Mini PCI ExpressCard for wireless LAN connection Before you start, print these instructions. DANGER During electrical storms, do not connect the cable to or disconnect it from the telephone outlet on the wall. DANGER Electric current from power, telephone, and communication cables is hazardous. To avoid shock hazard, disconnect the cables before opening the cover of this slot.
5. Remove the screw 1 . The card pops up 2 . Remove the card. 6. Align the contact edge of the new PCI Express Mini Card with the corresponding socket card until you can snap it into place. Secure the card with the screw 2 . 76 User Guide 1 .
7. Connect the antenna cables to the new PCI Express Mini Card as shown in the drawing. Be sure to attach the gray cable to the connector marked “MAIN” or “M” on the card, and the black cable to the connector marked “AUX” or “A”. 8. Reinstall the keyboard. See “Replacing the keyboard” on page 67. 9. Turn the computer over again. Connect the ac power adapter and all cables. Replacing a Mini PCI ExpressCard for wireless WAN connection Before you start, print these instructions.
4. If a tool for removing connectors is included in the package with the new card, use it to disconnect the cables from the card. If no such tool is included, disconnect the cables by picking up the connectors with your fingers and gently unplugging them. Note: Depending on the system configuration of your computer, the card might have only one connector. 5. Remove the screw 78 User Guide 1 . The card pops up 2 . Remove the card.
6. Align the contact edge of the new PCI Express Mini Card with the corresponding socket card until you can snap it into place. Secure the card with the screw 2 . 1 . Pivot the 7. Connect the antenna cables to the new PCI Express Mini Card as shown in the drawing. Be sure to attach the red cable to the connector marked “MAIN” OR “M” on the card, and the blue cable to the connector marked “AUX” or “A”. 8. Reinstall the keyboard. See “Replacing the keyboard” on page 67. 9. Turn the computer over again.
5. If a tool for removing connectors is included in the package with the new card, use it to disconnect the cables from the card. If no such tool is included, disconnect the cables by picking up the connectors with your fingers and gently unplugging them. Note: Depending on the system configuration of your computer, the card might have only one connector. 6. Remove the screw 1 . The card with bracket pops up 7. Remove the card from the bracket. 80 User Guide 2 . Remove the card.
8. Insert the new card into the bracket. 9. Align the contact edge of the new PCI Express Mini Card with the corresponding socket card until you can snap it into place. Secure the card with the screw 2 . 1 . Pivot the 10. Connect the antenna cables to the new PCI Express Mini Card as shown in the drawing. Be sure to attach the red cable to the connector marked “MAIN” OR “M” on the card, and the blue cable to the connector marked “AUX” or “A”. Chapter 6.
11. Reinstall the keyboard. See “Replacing the keyboard” on page 67. 12. Turn the computer over again. Connect the ac power adapter and all cables. Replacing the backup battery Before you start, print these instructions. DANGER If the backup battery is incorrectly replaced, there is danger of an explosion. The backup battery contains a small amount of harmful substances. To avoid possible injury: • Replace only with a battery of the type recommended by Lenovo. • Keep the battery pack away from fire.
4. Detach the connector 1 . Then remove the backup battery 5. Install the new backup battery 1 2 . Then attach the connector . 2 . 6. Reinstall the keyboard. See “Replacing the keyboard” on page 67. 7. Turn the computer over again. Connect the ac power adapter and all cables. Chapter 6.
84 User Guide
Chapter 7. Advanced configuration While it is important to protect files, data, and settings that are on the hard disk drive or solid state drive, you also might need to install a new operating system, install new device drivers, update your system UEFI BIOS, or recover preinstalled software. This information will help you handle your computer with proper care and keep it in top working shape.
Country or region: Code China: SC Denmark: DK Finland: FI France: FR Germany: GR Italy: IT Japan: JP Netherlands: NL Norway: NO Spain: SP Sweden: SV Taiwan and Hong Kong: TC United States: US Installing the Windows 7 operating system Before you start, print these instructions. To install the Windows 7 operating system and its related software on your computer, do the following: 1. Start ThinkPad Setup. 2. Select Startup. 3. Select UEFI/Legacy Boot. 4.
To install a fix module, run the EXE file in a subfolder and follow the instructions on the screen. Note: If you remove the hard disk drive from the computer with a single-core processor and install it on a computer with a dual-core processor, you can get access to the hard disk drive. The opposite, however, is not true: If you remove the hard disk drive from a computer with a dual-core processor and install it on a computer with a single-core processor, you cannot get access to the hard disk drive.
12. Click OK. 13. Confirm the correct display type, then click Next. 14. When installation completes, click Close. 15. Click Close to close the Display Properties window. 16. Click OK on the Monitor tab. 17. Click OK and close the Display Settings window. Installing other drivers and software The device drivers are provided in the C:\SWTOOLS\DRIVERS directory on your hard disk drive.
• System-unit serial number • System board serial number • Asset Tag • CPU Type • CPU Speed • Installed memory • UUID • MAC address (Internal LAN) Config menu If you need to change the configuration of your computer, select Config from the ThinkPad Setup menu. Notes: • Default values are in boldface. The default settings are already optimized for you. If you consider changing the computer configuration, proceed with extreme caution. Setting the configuration incorrectly might cause unexpected results.
Table 4. Config menu items (continued) Menu item Submenu item Selection Comments USB USB UEFI BIOS Support • Disabled Enable or disable boot support from USB storage devices. • Enabled USB 3.0 Mode • Disabled • Enabled • Auto Set the USB 3.0 controller mode for the ports shared between USB 2.0 and USB 3.0 controller. If you select Auto, it enables you to connect and route appropriate USB 3.0 or USB 2.0 connectors. If you select Enabled, it enables the USB 3.0 mode and allows the USB 3.
Table 4. Config menu items (continued) Menu item Submenu item Selection Comments Display Boot Display Device • ThinkPad LCD Select the display device to be activated at boot time. This selection is effective for boot time, password prompt, and ThinkPad Setup. • HDMI • DisplayPort Graphics Device • Integrated Graphics • NVIDIA Optimus The Integrated Graphics mode provides longer battery life. The NVIDIA Optimus mode runs as Integrated Graphics mode and Discrete Graphics is enabled on demand.
Table 4. Config menu items (continued) Menu item Submenu item Selection Comments • 15 minutes only seconds to resume normal operation. • 30 minutes • 1 hour • 2 hours Note: To use this feature, a special partition on the solid state drive is required. • 3 hours Disable Built-in Battery Use this feature to temporarily disable the built-in battery. The system will be automatically powered off after you select this item. Then the computer is ready to be serviced.
• System Time To change the date and time, do the following: 1. Using the up and down arrow keys to select the item to change the date or time. 2. Press Tab, Shift+Tab, or Enter to select a field. 3. Type the date or time. Note: Another way to adjust the date and time is by pressing + or –. 4. Press F10 to save the changes and restart the system. Security menu If you need to set the security features of your computer, select Security from the ThinkPad Setup menu. Notes: • Default values are in boldface.
Table 5. Security menu items (continued) Menu item Submenu item Selection Comments authentication on the operating system. Password at restart • Disabled • Enabled Power-On Password • Disabled • Enabled Hard Disk1 Password • Disabled • Enabled Security Chip Security Chip • Active • Inactive • Disabled If you select and enable Password at restart, a password prompt is displayed when you restart the computer.
Table 5. Security menu items (continued) Menu item Submenu item Selection Comments UEFI BIOS Update Option Flash BIOS Updating by End-Users • Disabled If you select Enabled, all users can update the UEFI BIOS. If you select Disabled, only the person who knows the supervisor password can update the UEFI BIOS.
Table 5. Security menu items (continued) Menu item Submenu item Selection Comments Fingerprint Reader • Disabled If you select Enabled, you can use the fingerprint reader. • Enabled Thunderbolt • Disabled • Enabled Anti-Theft Intel AT Module Activation • Disabled • Enabled • Permanently Disabled If you select Enabled, you can use the Thunderbolt feature. Enable or disable the UEFI BIOS interface to activate the Intel AT module, which is an optional the anti-theft service from Intel.
3. Press F10 to save the changes and restart the system. To change the startup sequence temporarily so that the system starts up from a different drive, do the following: 1. Turn off the computer. 2. Turn on the computer, then, while the ThinkPad logo is displayed at the lower-left of the screen, press F12. 3. Select the device you want to start first. Note: The Boot menu will be displayed when the system cannot boot from any device or the operating system cannot be found.
Table 6. Startup menu items (continued) Menu item Selection Comments Boot Device List F12 Option • Disabled If you select Enabled, the F12 key is recognized and the Boot menu window is displayed. • Enabled Boot Order Lock • Disabled • Enabled If you select Disabled, your computer will boot using the default priority. If you select Enabled, your computer will boot using the priority you have customized.
System management Read this topic to learn more about features of system management: Desktop Management Interface The system UEFI BIOS of your computer supports an interface called System Management BIOS Reference Specification (SMBIOS) V2.6.1 SMBIOS provides information about the hardware components of your system. It is the responsibility of the BIOS to supply this database with information about itself and the devices on the system board.
To enable or disable Wake on LAN, do the following: 1. Start ThinkPad Setup. 2. Select Config. The Config submenu is displayed. 3. Select Network. The Network item submenu is displayed. 4. For Wake On LAN, select one of the following: AC Only, AC and Battery, or Disabled. 5. Press F10 to save changes and exit.
Chapter 8. Preventing problems An important part of owning a ThinkPad notebook computer is maintenance. With proper care, you can avoid common problems. The chapter provides information that can help you keep your computer running smoothly. • “General tips for preventing problems” on page 101 • “Making sure device drivers are current” on page 102 • “Taking care of your computer” on page 103 General tips for preventing problems 1.
returns any failing error codes or messages, call the Customer Support Center with the codes or messages and the computer in front of you. A technician will assist you further. 15. If required, you can find your country's Customer Support Center at: http://www.lenovo.com/support/phone. When calling the Customer Support Center, ensure that you have your machine model type, serial number, and the computer in front of you.
Taking care of your computer Although your computer is designed to function reliably in normal work environments, you need to use common sense in handling it. By following these important tips, you will get the most use and enjoyment out of your computer. Be careful about where and how you work • Store packing materials safely out of the reach of children to prevent the risk of suffocation from plastic bags.
• Store your external and removable hard disk drive or optical drives in the appropriate containers or packaging when they are not being used. • Before you install any of the following devices, touch a metal table or a grounded metal object. This action reduces any static electricity from your body. The static electricity could damage the device.
6. Rinse the sponge with clean running water. 7. Wipe the cover with the clean sponge. 8. Wipe the surface again with a dry, soft, lint-free cloth. 9. Wait for the surface to dry completely and remove any fibers from the cloth. Cleaning your computer keyboard To clean the computer keyboard, do the following: 1. Apply some isopropyl rubbing alcohol to a soft, dust-free cloth. 2. Wipe each keytop surface with the cloth.
106 User Guide
Chapter 9. Troubleshooting computer problems This chapter provides information on what to do if you experience a problem with your computer. This chapter contains the following topics: • “Diagnosing problems” on page 107 • “Troubleshooting” on page 107 Diagnosing problems If you experience problems with your computer, use the Lenovo Solution Center program as a starting point for solving them. The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems.
• If the computer is turned off, restart the computer by pressing the power button. If you can not restart the computer, go to step 2. • If you can not turn off your computer by pressing and holding the power button, remove all power sources from the computer and reset reset the system by inserting a straightened paper clip into the emergency reset hole. To locate the emergency reset hole, see “Bottom view” on page 6. 2. While the computer is turned off, remove all power sources from the computer.
• Message: 0183: Bad CRC of Security settings in EFI Variable. Enter ThinkPad Setup. Solution: Checksum of the Security settings in the EFI Variable is not correct. Enter ThinkPad Setup to check the Security settings, Press F10 and then press Enter to restart the system. If you still have a problem, have the computer serviced. • Message: 0187: EAIA data access error. Solution: Enter ThinkPad Setup to check the Security settings. Press F10 and then press Enter to restart the system.
Solution: ThinkVantage Active Protection sensor is not working correctly. Have the computer serviced. • Message: 2100: Initialization error on HDD0 (Main HDD). Solution: The hard disk drive is not working. Have the hard disk drive serviced. • Message: 2101: Detection error on HDD1 (Ultrabay HDD) Solution: The Ultrabay hard disk drive is not working. Have the Ultrabay hard disk drive serviced. • Message: 2102: Detection error on HDD2 (Mini SATA) Solution: The Mini SATA device is not working.
1. Start Power Manager. 2. Click the Power plan tab, and then select Maximum Performance from the predefined power plans. • Problem: When I turn on the computer, nothing is displayed on the screen and the computer does not beep while starting up. Note: If you are not sure whether you heard any beeps, turn off the computer by pressing and holding the power button for four seconds or more. Turn it on and listen again. Solution: Ensure that: – The battery is installed correctly.
Table 7. Beep errors (continued) Problem Solution One long and two short beeps The video function has a problem. Have the computer serviced. Four cycles of four short beeps The Security Chip has a problem. Have the computer serviced. Five short beeps The system board has a problem. Have the computer serviced. Five short beeps, pause, five short beeps, and pause Continue to boot immediately when the error was detected.
If you configured the adapter for full duplex, ensure that the switch port also is configured for full duplex. Setting the wrong duplex mode can degrade performance, cause data loss, or result in lost connections. – You have installed all networking software that is necessary for your network environment. Check with your LAN administrator for the necessary networking software. • Problem: The adapter stops working for no apparent reason. Solution: The network driver files might be corrupt or missing.
Note: Depending on your computer, some models do not have a wireless WAN card. Bluetooth problems • Problem: Sound does not come from the Bluetooth headset/headphone but comes from the local speaker even though the Bluetooth headset/headphone is connected using a Headset profile or AV profile. Solution: Do the following: 1. Exit the application that uses the sound device (for example, Windows Media Player). 2. Open Control Panel by clicking Start ➙ Control Panel ➙ Hardware and Sound ➙ Sound ➙ Playback. 3.
If the problem persists, ensure that the correct device driver is installed. 1. Click Start ➙ Control Panel. Change the view of Control Panel from Category to Large icons or Small icons. 2. Click Keyboard. 3. Select the Hardware tab. In the Device Properties pane, ensure that you see this message: Device Status: This device is working properly. If keys on the keyboard still do not work, have the computer serviced. • Problem: All or some keys on the external numeric keypad do not work.
9. Click the Properties button. If you are prompted for an administrator password or confirmation, type the password or provide confirmation. Check the Device status box and ensure that the device is working correctly. If not, click the Troubleshoot button and follow the instructions on the screen. • Problem: Incorrect characters are displayed on the screen.
2. Turn on the external monitor and the computer. 3. Right-click on the desktop, and click Screen resolution. Note: If your computer cannot detect the external monitor, click the Detect button. 4. Click the icon for the desired monitor (the Monitor-2 icon is for the external monitor). 5. Click Advanced Settings. 6. Click the Monitor tab. Check the monitor information window to ensure that the monitor type is correct. If it is, click OK to close the window; otherwise do the following. 7.
1. Connect the external monitor to the monitor connector, and then connect the monitor to an electrical outlet. 2. Turn on the external monitor and the computer. 3. Right-click on the desktop, and click Screen resolution. 4. Click the Monitor-2 icon. 5. Select Extend these displays for multiple displays. 6. Click the Monitor-1 icon (for the primary display, the computer display). 7. Set the resolution for the primary display. 8. Click the Monitor-2 icon (for the external monitor). 9.
Solution: Ensure that the Microphone Boost function is turned on and set by doing the following: 1. Click Start ➙ Control Panel. 2. Click Hardware and Sound. 3. Click Sound. 4. Click the Recording tab in the Sound window. 5. Select Microphone, and click the Properties button. 6. Click the Levels tab, and move the Microphone Boost slider upwards. 7. Click OK. Note: For details about controlling volume, refer to your Windows online help. • Problem: A volume or balance slider cannot be moved.
Fingerprint reader problems • Problem: The surface of the reader is dirty, stained, or wet. Solution: Gently clean the surface of the reader with a dry, soft, lint-free cloth. • Problem: The reader often fails to enroll or authenticate your fingerprint. Solution: If the surface of the reader is dirty, stained, or wet, gently clean the surface of the reader with a dry, soft, lint-free cloth. For tips on how to maintain the fingerprint reader, refer to “Maintaining the fingerprint reader” on page 53.
2. If the connection of the ac power adapter is correct, turn off the computer, then disconnect the ac power adapter and remove the main battery. 3. Reinstall the battery and reconnect the ac power adapter, then turn on the computer. 4. If the power adapter icon still is not displayed on the taskbar and the ac power indicator does not light up, have the ac power adapter and your computer serviced. Note: To display the power adapter (power plug) icon, click Show hidden icons on the taskbar.
If you receive an error message while the operating system is loading the desktop configuration after the POST is completed, check the following items: 1. Go to the Lenovo Support Web site at http://www.lenovo.com/support and search for the error message. 2. Go to the Microsoft Knowledge Base homepage at http://support.microsoft.com/ and search for the error message. Sleep and hibernation problems • Problem: The computer enters sleep mode unexpectedly.
If your computer tries to enter sleep mode but the request is rejected, the device attached to the USB connector might have been disabled. If this occurs, do a hot-unplug-and-plug operation for the USB device. • Problem: The battery discharges slightly while the computer is in hibernation mode. Solution: If the wakeup function is enabled, the computer consumes a small amount of power. This is not a defect. For details, refer to “Power-saving modes” on page 28.
• Problem: The tray does not open even if you press the eject button. Solution: When your computer is not turned on, pressing the eject button does not cause the drive tray to open. Ensure that the computer is turned on and that the drive connector is firmly connected to the computer. If the tray still does not open, ensure that the computer is running, and insert the end of a straightened paper clip into the emergency eject hole. The tray will open.
Problems with ports and connectors The following are the most common problems with ports and connectors. A USB problem Problem: A device connected to the USB connector does not work. Solution: Open the Device Manager window. Ensure that the USB device setup is correct, and that the assignment of computer resource and the installation of the device driver are correct. Click Start ➙ Control Panel ➙ Hardware and Sound ➙ Device Manager.
126 User Guide
Chapter 10. Getting support This chapter provides information about getting help and support from Lenovo. • “Before you contact Lenovo” on page 127 • “Getting help and service” on page 127 • “Purchasing additional services” on page 129 Before you contact Lenovo Often, you can solve your computer problems by referring to the information in the explanations of error codes, running diagnostic programs, or by consulting the Lenovo Web site.
about where to go for additional information about Lenovo and our products, what to do if you experience a problem with your computer, and whom to call for service should it be necessary. Information about your computer and preinstalled software, if any, is available in the documentation that comes with your computer. That documentation includes printed books, online books, readme files, and help files. In addition, information about Lenovo products is available on the World Wide Web.
• Engineering change management - Occasionally, there might be changes that are required after a product has been sold. Lenovo or your reseller, if authorized by Lenovo, will make selected Engineering Changes (ECs) that apply to your hardware available. The following items are not covered: • Replacement or use of parts not manufactured for or by Lenovo or nonwarranted parts • • • • • Note: All warranted parts contain a 7-character identification in the format FRU XXXXXXX.
For more information about these services, go to: http://www.lenovo.com/accessories/services/index.
Appendix A. Regulatory information Wireless related information Wireless interoperability The Wireless LAN PCI Express Mini Card is designed to be interoperable with any wireless LAN product that is based on DSSS, CCK, and/or OFDM radio technology, and is compliant to: • The 802.11b/g Standard, 802.11a/b/g or 802.11n draft 2.0 on Wireless LANs, as defined and approved by the Institute of Electrical and Electronics Engineers. • The WiFi certification as defined by the Wi-Fi Alliance.
• Battery Status Profile Usage environment and your health Integrated wireless cards emit radio frequency electromagnetic energy like other radio devices. However, the level of energy emitted is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Due to the fact that integrated wireless cards operate within the guidelines found in radio frequency safety standards and recommendations, Lenovo believes they are safe for use by consumers.
Locating wireless regulatory notices For more information about the wireless regulatory notices, refer to the Regulatory Notice shipped with your computer. If your computer is shipped without the Regulatory Notice, you can find it on the Web site at: http://www.lenovo.com/ThinkPadUserGuides Export classification notice This product is subject to the United States Export Administration Regulations (EAR) and has an Export Classification Control Number (ECCN) of 4A994.b.
European Union - Compliance to the Electromagnetic Compatibility Directive This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the installation of option cards from other manufacturers.
Japan VCCI Class B compliance statement Japan compliance statement for products which connect to the power mains with rated current less than or equal to 20 A per phase Lenovo product service information for Taiwan Appendix A.
136 User Guide
Appendix B. WEEE and recycling statements Lenovo encourages owners of information technology equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. Information on product recycling offerings can be found on Lenovo's Internet site at http://www.lenovo.com/social_responsibility/us/en/.
Disposing of Lenovo computer components Some Lenovo computer products sold in Japan may have components that contain heavy metals or other environmental sensitive substances. To properly dispose of disused components, such as a printed circuit board or drive, use the methods described above for collecting and recycling a disused computer or monitor.
framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union. This label is applied to various batteries to indicate that the battery is not to be thrown away, but rather reclaimed upon end of life per this Directive. In accordance with the European Directive 2006/66/EC, batteries and accumulators are labeled to indicate that they are to be collected separately and recycled at end of life.
140 User Guide
Appendix C. ENERGY STAR model information ENERGY STAR® is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy aimed at saving money and protecting the environment through energy efficient products and practices. Lenovo is proud to offer our customers products with the ENERGY STAR qualified designation.
5. Click the Power Management tab. 6. Clear the Allow this device to wake the computer check box. 7. Click OK.
Appendix D. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Access Connections Active Protection System OneKey ThinkLight ThinkPad ThinkVantage TrackPoint UltraConnect UltraNav Intel and Intel SpeedStep are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft, Windows, Bing, and BitLocker are trademarks of the Microsoft group of companies.
Part Number: (1P) P/N: **
