ThinkServer RD430 User Guide Machine Types: 3057, 3059, 3061, 3064, 3065, 3069, 3070, 3071, and 4306
Note: Before using the information and the product it supports, be sure to read and understand the following: • The Read Me First that comes with your product • “Safety information” on page iii • Appendix A “Notices” on page 189 First Edition (August 2012) © Copyright Lenovo 2012. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No.
Contents Safety information . . . . . . . . . . iii Chapter 1. General information . . . . . 1 Introduction . . . . . . . . . . . . . . . . . Server documentation . . . . . . . . . . . . . 1 2 Chapter 2. Server setup road map . . . 5 Chapter 3. Product overview . . . . . . 7 Server package . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . Software . . . . . . . . . . . . . . . . ThinkServer EasyStartup . . . . . . . .
Installing or removing the ThinkServer RAID 700 Battery . . . . . . . . . . . . . . Installing or removing the expander card. . . Installing or removing an Ethernet card . . . Installing or removing the ThinkServer RAID 300 Upgrade Key for Advanced RAID . . . . Installing or removing the ThinkServer Management Module Premium . . . . . . Installing or removing the ThinkServer Trusted Platform Module . . . . . . . . . . . . Installing or replacing a hot-swap redundant power supply . . . . . . . . . . . . .
Safety information Note: Before using the product, be sure to read and understand the multilingual safety instructions on the documentation DVD that comes with the product. Antes de usar o produto, leia e entenda as instruções de segurança multilíngues no DVD de documentação que o acompanha. Преди да използвате този продукт, задължително прочетете и вникнете в многоезичните инструкции за безопасност в DVD диска с документация, който се предоставя с продукта.
Przed skorzystaniem z produktu należy zapoznać się z wielojęzycznymi instrukcjami bezpieczeństwa znajdującymi się na płycie DVD z dokumentacją dostarczoną wraz z produktem. Antes de utilizar o produto, leia atentamente as instruções de segurança multilingues que constam no DVD de documentação fornecido com o produto. Înainte de a utiliza produsul, asiguraţi-vă că aţi citit şi înţeles instrucţiunile de siguranţă în mai multe limbi de pe DVD-ul cu documentaţie care însoţeşte produsul.
Statement 1 DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. • Connect all power cords to a properly wired and grounded electrical outlet. • Connect to properly wired outlets any equipment that will be attached to this product. • When possible, use one hand only to connect or disconnect signal cables.
Statement 3 CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
Statement 6 CAUTION: If you install a strain-relief bracket option over the end of the power cord that is connected to the device, you must connect the other end of the power cord to a power source that is easily accessible in case it needs to be disconnected. Statement 7 CAUTION: If the device has doors, ensure that you remove or secure the doors before moving or lifting the device to protect against personal injury. The doors will not support the weight of the device.
Statement 11 CAUTION: The following label indicates a potential heat hazard. Statement 12 DANGER Overloading a branch circuit is a potential fire hazard and a shock hazard under certain conditions. To avoid these hazards, ensure that your system electrical requirements do not exceed branch current ratings at the installation site. Statement 13 CAUTION: Ensure that the rack is secured properly to avoid tipping when the server unit is extended on the rails.
Statement 16 CAUTION: To reduce the risk of electric shock or energy hazards: • This equipment must be installed by trained service personnel in a restricted-access location, as defined by your local electrical code and the latest edition of IEC 60950. • Connect the equipment to a reliably earthed safety extra low voltage (SELV) source. An SELV source is a secondary circuit that is designed so that normal and single fault conditions do not cause the voltages to exceed a safe level (60 V direct current).
Statement 20 CAUTION: A lithium ion battery is provided. To avoid possible explosion, do not burn the battery. Replace the battery only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations.
Chapter 1. General information This chapter provides some general information about your product. This chapter contains the following items: • “Introduction” on page 1 • “Server documentation” on page 2 Introduction This user guide for your Lenovo® ThinkServer® product contains information about the server features, specifications, component locations, configuration instructions, hardware replacement procedures, and basic troubleshooting and diagnostics.
Record information about your server in the following table. You will need the information if you ever need to have your server serviced. For where to find the product information label on the chassis, see “Machine type, model, and serial number label” on page 13.
Documentation DVD The documentation DVD, which comes with your server, contains various documents for your server in Portable Document Format (PDF) and HyperText Markup Language (HTML). The documentation DVD is not bootable. To view the documents on the DVD, you will need a computer with a Web browser and the Adobe Reader program, which is available for download at: http://www.adobe.com To start the documentation DVD, insert the DVD into the optical drive.
Document only for trained service personnel The following document is intended only for trained service personnel of Lenovo. Hardware Maintenance Manual This document provides information about component locations, replacement procedures for major Field Replaceable Units (FRUs), and troubleshooting and diagnostics. This document is updated frequently, and the most up-to-date version is always available in English on the Lenovo Web site at: http://www.lenovo.
Chapter 2. Server setup road map This chapter provides a general road map to guide you through setting up your server. The server setup procedure varies depending on the configuration of the server when it was delivered. In some cases, the server is fully configured and you just need to connect the server to the network and an ac power source, and then you can turn on the server.
6 ThinkServer RD430 User Guide
Chapter 3. Product overview This chapter provides information about the server package, features, specifications, software programs, and component locations. This chapter contains the following items: • “Server package” on page 7 • “Features” on page 8 • “Specifications” on page 11 • “Software” on page 12 • “Locations” on page 13 Server package The server package includes the server, power cord(s), a rail kit, printed documentation, a documentation DVD, and software media.
Features This topic provides general information about the server features for a variety of models. Depending on your specific model, some features might vary or unavailable. For information about your specific model, use the Setup Utility program. See “Viewing information in the Setup Utility program” on page 59.
Input/Output (I/O) features • One serial connector on the rear panel • One Video Graphics Array (VGA) connector on the front panel in some models and one VGA connector on the rear panel • Six USB 2.0 connectors (two on the front panel and four on the rear panel) • Three RJ-45 Ethernet connectors on the rear panel (Ethernet connector 0 is for system management) For the location information about the connectors, refer to the related topics in “Locations” on page 13.
The BIOS Setup Utility program helps you view the server information and configure the server in the pre-operating system environment. See “Using the Setup Utility program” on page 59. – TMM (also known as BMC) and Intelligent Platform Management Interface (IPMI) 2.0 The system board platform management subsystem is based on the integrated TMM features. The TMM is a management chip that is integrated on the system board of your server.
a TMM Premium from Lenovo and install it on the TMM Premium connector (also known as iKVM connector) on the system board of your server to enable the iKVM function and activate the advanced system management features. For more information about advanced system management, refer to the ThinkServer Management Module User Guide, which is available for download at: http://www.lenovo.com/ThinkServerUserGuides Specifications This topic lists the physical specifications for your server.
Software This topic provides information about the software programs that you can use to help you set up, use, and maintain the server. ThinkServer EasyStartup The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported Microsoft Windows and Linux operating systems and device drivers on your server. This program is provided with your server on a self-starting (bootable) ThinkServer EasyStartup DVD.
consumption and electric current calculations, and reports to help equipment managers significantly increase efficiency in deploying the equipment and conveniently manage the equipment. To download the Lenovo Rack Planner program, go to http://www.lenovo.com/drivers and follow the instructions on the Web page. For detailed information about using the Lenovo Rack Planner program, refer to the help system for the program.
The machine type, model, and serial number label is attached on the pull-out information card in the following server models: • Server models with eight 3.5-inch hard disk drive bays • Server models with 2.5-inch hard disk drive bays The pull-out information card is a small plastic tab and can be slid out of the front of the chassis. Figure 2. Label on server models with eight 3.5-inch hard disk drive bays Figure 3. Label on server models with 2.
For server models with 12 3.5-inch hard disk drive bays, the machine type, model, and serial number label is attached on the left side of the server. Figure 4. Label on server models with 12 3.5-inch hard disk drive bays Front view of the server This topic provides information to help you locate the parts on the front of the server. The front view of the server varies by model.
Front view of server models with eight 3.5-inch hard disk drive bays The following illustration shows the front view of server models with eight 3.5-inch hard disk drive bays. Figure 5. Front view of server models with eight 3.5-inch hard disk drive bays 1 3.5-inch hard disk drive area 5 Diagnostic panel (varies by model) 2 Rack handle (left) 6 Slim optical drive (available in some models) 3 Pull-out information card 7 Rack handle (right) 4 Front panel 1 3.
3 Pull-out information card The machine type, model, and serial number label of the server is attached on the pull-out information card. See “Machine type, model, and serial number label” on page 13. 4 Front panel For detailed information about the controls, connectors, and status LEDs on the front panel, see “Front panel” on page 21. 5 Diagnostic panel The diagnostic panel varies by model. For detailed information, see “Diagnostic module” on page 23.
1 3.5-inch hard disk drive area The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied. The number of the installed hard disk drives in your server varies by model. The vacant hard disk drive bays are occupied by dummy hard disk drive trays. For server models with 12 3.5-inch hard disk drive bays, the hard disk drive bay numbers are marked on the top edge of the front bezel. Figure 8. 3.
5 Power status LED Color Description On Green The server is on. Off None The server is off. Blinking Green The server is in ACPI S1 mode, which also is known as Power On Suspend (POS) mode. In this mode, the microprocessor(s) are not working while other hardware devices are still working. ID button with ID LED When you press the ID button, the ID LEDs on both the front and rear of the server are lit to help you locate the server among other servers.
Front view of server models with 2.5-inch hard disk drive bays The following illustration shows the front view of server models with 2.5-inch hard disk drive bays. Figure 9. Front view of server models with 2.5-inch hard disk drive bays 1 2.5-inch hard disk drive area (right cage) 5 Rack handle (left) 2 2.5-inch hard disk drive area (middle cage) 6 Diagnostic panel (varies by model) 3 Pull-out information card 7 Front panel 4 Slim optical drive (available in some models) 8 Rack handle (right) 1 2.
4 Slim optical drive Some server models come with a slim SATA optical drive. 5 Rack handle (left) 8 Rack handle (right) If your server is installed in a rack cabinet, you can use the rack handles to help you slide the server out of the rack cabinet; or use the rack handles and screws to secure the server in the rack cabinet so that the server cannot slide out, especially in vibration-prone areas. For more information, refer to the Rack Installation Instructions that comes with your server.
1 Power switch with power status LED You can press the power switch to turn on the server when you finish setting up the server. You also can hold the power switch for several seconds to turn off the server if you cannot turn off the server from the operating system. See Chapter 4 “Turning on and turning off the server” on page 57. The power status LED helps you to determine the current power status. 2 Power status LED Color Description On Green The server is on. Off None The server is off.
6 Front USB connectors Used to attach a USB-compatible device, such as a USB keyboard, mouse, scanner, or printer. If you have more than six USB devices, you can purchase a USB hub, which you can use to connect additional USB devices. 7 VGA DB-15 connector Used to attach a VGA-compatible video device, such as a VGA monitor. Diagnostic module This topic applies only to the following server models: • Server models with eight 3.5-inch hard disk drive bays • Server models with 2.
1 Power supply error LED When the power supply error LED is lit in amber, it indicates that there is a power supply problem. To identify the failing power supply, check the status LED near the power cord connector on the redundant power supply. When the LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly. When the LED is lit in amber, it indicates that the hot-swap redundant power supply is likely to fail or has failed.
1 System fan error LEDs When a system fan error LED is lit in amber, it indicates that the corresponding system fan is operating slowly or has failed. The following illustration shows the system fans and their numbers. Notes: • Depending on the model, your server might look slightly different from the illustration. • Your server has four system fans. The callout 3 and callout 6 indicate dummy system fans. Figure 14. System fans Chapter 3.
2 CPU1 DIMM status LEDs 3 CPU2 DIMM status LEDs When a DIMM status LED is lit in amber, it indicates that the corresponding memory module is overheated. The following illustration shows the memory modules and their numbers. Figure 15. DIMM status LEDs and DIMMs 4 Ambient temperature limit LED When this LED is lit in amber, it indicates that the ambient temperature is below 7°C (44.6°F) or over 40°C (104°F), which is not proper for server operation.
The following illustration shows the rear view of the server. Figure 16.
3 PCI Express card area for cards on the riser card assembly 2 There are three PCI Express card slots on the riser card assembly 2 for installing Ethernet cards or other supported PCI Express cards. Figure 17. Riser card assembly 2 Note: The slot 1 and slot 2 are supported only in server models with two microprocessors. For server models with one microprocessor, the slot 1 and slot 2 are covered.
4 PCI Express card area for cards on the riser card assembly 1 There are two PCI Express card slots on the riser card assembly 1. Figure 18. Riser card assembly 1 Note: For a RAID card, it must be installed into the upper slot (callout 2 ) on the riser card assembly 1. For an expander card, it must be installed into the lower slot (callout 1 ) on the riser card assembly 1.
5 8 9 Ethernet connectors (RJ-45) Used to attach an Ethernet cable for a LAN. Each Ethernet connector has two status LEDs to help you identify the Ethernet connectivity, activity, and connection speed. Notes: • The Ethernet connector 0 (callout 9 ) marked with “MGMT” is for system management. If you want to use remote management functions, you need to connect an Ethernet cable to the Ethernet connector 0. • The Ethernet connector 0 for system management is 82574L by default.
11 ID LED When you press the ID button on the front of the server, the ID LEDs on both the front and rear of the server are lit to help you locate the server among other servers. You also can turn on the ID LEDs using a remote management program for server presence detection. ID LED Color Description On Blue The server is identified. Off None The ID LED is not in use or the server is not identified.
Components of server models with eight 3.5-inch hard disk drive bays Figure 20. Components of server models with eight 3.5-inch hard disk drive bays 1 Cooling shroud 12 Pull-out information card 2 Power supply cooling shroud 13 Rack handle (left) 3 Riser card assembly 2 14 Front panel board 4 One or two hot-swap redundant power supplies 15 Backplane for server models with eight 3.
Components of server models with 12 3.5-inch hard disk drive bays Figure 21. Components of server models with 12 3.5-inch hard disk drive bays 1 Cooling shroud 10 Backplane for server models with 12 3.
Components of server models with 2.5-inch hard disk drive bays Figure 22. Components of server models with 2.
Hot-swap hard disk drive status LEDs Each hot-swap hard disk drive has two status LEDs on the front. Figure 23. 3.5-inch hot-swap hard disk drive status LEDs Figure 24. 2.5-inch hot-swap hard disk drive status LEDs 1 Hard disk drive activity LED 2 Hard disk drive RAID status LED Description Off Off The hard disk drive has failed or is not present. On, green Off The hard disk drive is present but not in use. Blinking, green Off The hard disk drive is active and data is being transferred.
RAID card This topic provides information to help you locate the connectors on the RAID card if your server has a RAID card installed in the longer slot of the riser card assembly 1. Some server models come with a RAID card to provide advanced SATA/SAS hardware RAID functions. You also can purchase a supported RAID card from Lenovo and install it into the server. See “Installing or removing the RAID card” on page 101.
ThinkServer RAID 700 Adapter The following illustration shows the connectors on the ThinkServer RAID 700 Adapter. Figure 26. ThinkServer RAID 700 Adapter 1 Ports 7-4 3 Board-to-board connector 2 Ports 3-0 1 Ports 7-4 Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 42. 2 Ports 3-0 Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 42.
The following illustration shows the connectors on the expander card. Each connector on the expander card is used to connect a mini-SAS to mini-SAS signal cable. For detailed information, see “Mini-SAS to mini-SAS signal cable connections” on page 42. Figure 27.
The following illustrations show the connectors on the backplane for server models with eight 3.5-inch hard disk drive bays. Figure 28. Front view of the backplane for server models with eight 3.5-inch hard disk drive bays 1 Slot 0 for a 3.5-inch hard disk drive 5 Slot 7 for a 3.5-inch hard disk drive 2 Slot 2 for a 3.5-inch hard disk drive 6 Slot 5 for a 3.5-inch hard disk drive 3 Slot 4 for a 3.5-inch hard disk drive 7 Slot 3 for a 3.5-inch hard disk drive 4 Slot 6 for a 3.
Backplane for server models with 12 3.5-inch hard disk drive bays This topic provides information to help you locate the connectors on the backplane for server models with 12 3.5-inch hard disk drive bays. The following illustrations show the connectors on the backplane for server models with 12 3.5-inch hard disk drive bays. Figure 30. Front view of the backplane for server models with 12 3.5-inch hard disk drive bays 1 Slot 0 for a 3.5-inch hard disk drive 7 Slot 6 for a 3.
3 Mini-SAS ports 4-7 Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the hard disk drive 4 to hard disk drive 7. 4 Mini-SAS ports 0-3 Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the hard disk drive 0 to hard disk drive 3. 5 Signal cable connector Used to connect the signal cable for the front USB connectors on the left rack handle.
Figure 33. Rear view of the backplane for server models with 2.5-inch hard disk drive bays 1 8-pin power connector 3 Mini-SAS ports 0-3 2 Mini-SAS ports 4-7 4 Optical drive power connector 1 8-pin power connector Used to connect a power cable to provide power to the backplane.
Note: The option kit for a RAID card is designed for different types of servers and might contain additional cables that are not required for your server. Use the following instructions to connect cables from the RAID card to the backplane: 1.
Use the following instructions to connect cables from the RAID card to the expander card first: • If you are using a ThinkServer RAID 500 Adapter, do the following: 1. Use a mini-SAS to mini-SAS signal cable and connect the mini-SAS connector on one end of the cable to the port 0 on the ThinkServer RAID 500 Adapter. Then, connect the mini-SAS connector on the other end of the cable to the connector 1 on the expander card. 2.
Use the following instructions to connect cables from the expander card to the backplanes for 2.5-inch hard disk drives: 1. For hard disk drive 0 to hard disk drive 3, use a mini-SAS to mini-SAS signal cable and connect the mini-SAS connector 1 on one end of the cable to the connector 3 on the expander card. Then, connect the mini-SAS connector on the other end of the cable to the mini-SAS ports 0-3 on the backplane for 2.5-inch hard disk drives in the middle cage. 2.
Use the following instructions to connect cables from the expander card to the backplane for 12 3.5-inch hard disk drives: 1. For hard disk drive 0 to hard disk drive 3, use a mini-SAS to mini-SAS signal cable and connect the mini-SAS connector 1 on one end of the cable to the connector 3 on the expander card. Then, connect the mini-SAS connector on the other end of the cable to the mini-SAS ports 0-3 on the backplane for 12 3.5-inch hard disk drives. 2.
connect the mini-SAS connector on the other end of the cable to the mini-SAS ports 0-3 on the backplane. 2. If your server has more than four hard disk drives installed, for hard disk drive 4 to hard disk drive 7, use another mini-SAS to mini-SAS signal cable and connect the mini-SAS connector on one end of the cable to the SAS connector 4-7 on the system board. Then, connect the mini-SAS connector on the other end of the cable to the mini-SAS ports 4-7 on the backplane.
7 SAS connector 4-7 22 Backplane power connector 2 8 SAS connector 0-3 23 Microprocessor socket 2 9 System board battery 24 System fan 5 connector 10 Platform Controller Hub (PCH) 25 Memory slots (6) 11 Internal USB Type A connector 2 26 System fan 4 connector 12 TMM Premium connector 27 Microprocessor socket 1 13 Internal USB Type A connector 1 28 System fan 2 connector 14 TPM connector 29 Memory slots (6) 15 iButton socket 30 System fan 1 connector 1 Front panel connector Used to conne
10 Platform Controller Hub (PCH) This chip supports and provides many features. It serves as a PCH, which provides the data buffering and interface arbitration required to ensure that system interfaces operate efficiently and provides the bandwidth necessary for the system to achieve peak performance. 11 Internal USB Type A connector 2 13 Internal USB Type A connector 1 Used to connect a device that uses a USB Type A connector.
21 Backplane power connector 1 22 Backplane power connector 2 Used to connect the power cable(s) from the backplane. 24 26 28 30 System fan connectors There are four hot-swap system fans and two dummy system fans installed in the system fan cage in your server. Each system fan connector is used to connect a corresponding hot-swap system fan.
The following illustration shows the status of the jumpers and switches on the system board of your server. You can configure, recover, enable, or disable some specific features of the system board by setting the jumpers and switches. Figure 39.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 83. 4. If necessary, remove the cooling shroud. See “Removing and reinstalling the cooling shroud” on page 91. 5. Locate the Clear CMOS jumper on the system board.
3 System board switches There are four switches on the system board of your server. Figure 40. System board switches 1 1 BIOS recovery switch 3 Management Engine (ME) in force update switch 2 Clear password switch 4 Reserved for the manufacturer BIOS recovery switch Used to recover the BIOS if the power to your server is interrupted while the BIOS is being updated and your server cannot start correctly. To recover the BIOS, see “Recovering from a BIOS update failure” on page 66.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 83. 4.
Note: Depending on the model, your server might look slightly different from the illustrations in this topic. The server is designed so that LEDs remain lit when the server is connected to an ac power source but is not turned on, provided that the power supply is operating correctly. This helps you to isolate problems when the server is not turned on. Many errors are first indicated by a lit error LED on the diagnostic panel of some server models.
56 ThinkServer RD430 User Guide
Chapter 4. Turning on and turning off the server This chapter provides information about turning on and turning off the server. Turning on the server The server can be turned on in one of the following ways: • After you finish unpacking and setting up the server, connect it to an ac power source. Press the power switch on the front of the chassis to turn on the server.
• The server might be turned off as an automatic response to a critical system failure. Notes: • When you turn off the server and leave it connected to an ac power source, the server also can respond to a remote request to turn on the server. To remove all power from the server, you must disconnect the server from the ac power source. • For information about your specific operating system, refer to the related documentation or help system for the operating system.
Chapter 5.
– Select SATA/SAS Configuration and follow the instructions on the screen to view information about the installed SATA or SAS devices, such as a hard disk drive or an optical drive. • On the Server Management menu, select System Information to view information about your system. Setup Utility program interface This topic provides general information about the menus and items in the Setup Utility program.
Notes: • Enabled means that the function is configured. • Disabled means that the function is not configured. The Advanced menu contains the following submenus. For more information, enter the corresponding submenu and refer to the instructions on the screen. • PCI Configuration: View and set PCI configuration parameters. • ACPI Configuration: View and set ACPI configuration parameters.
• System Information: View basic information about your server. • BMC Network Configuration: Set BMC configuration parameters. Boot Options menu The Boot Options menu in the Setup Utility program provides an interface to help you view or change the server startup options, including the startup sequence and boot priority for various devices. Changes in the startup options take effect when the server starts. The startup sequence specifies the order in which the server checks devices to find a boot record.
Using passwords By using the Setup Utility program, you can set a password to prevent unauthorized access to your server. You do not have to set a password to use your server. However, using a password improves computing security. If you decide to set a password, read the following topics.
4. If you want to delete a password, type your current password. Press Enter when you are prompted to type a new password. Then, press Enter to confirm the new password. The previous password will be cleared. Note: For security reasons, it is recommended that you always set a password for your server. 5. Press F10 to save settings and exit the Setup Utility program. If you have forgotten the password, you can use the Clear password switch on the system board to erase the password.
Setting the mode of the Ethernet connector 0 The Ethernet connector 0 on the rear of the server is for system management. If you want to use remote management functions, you need to connect an Ethernet cable to the Ethernet connector 0. See “Rear view of the server” on page 26. The Ethernet connector 0 for system management is 82574L by default.
Updating (flashing) the BIOS This topic provides instructions on how to update (flash) the BIOS. Notes: • Update the BIOS on your server only if the newer BIOS version specifically solves a problem you have. We do not recommend BIOS updates for servers that do not need them. You can view the updated information for the new BIOS version in the installation instructions for the BIOS update utility program. • Downgrading the BIOS to an earlier version is not recommended and might not be supported.
4. Remove the server cover. See “Removing the server cover” on page 83. 5. Locate the BIOS recovery switch on the system board. See “System board jumpers and switches” on page 50. Then, remove any parts and disconnect any cables that might impede your access to the switch. 6. Move the BIOS recovery switch from the default off position to the on position. 7. Reinstall any parts and reconnect any cables. Then, reinstall the server cover. See “Completing the parts replacement” on page 174. 8.
• Easy-to-use, language-selectable interface • Integrated help system and user guide • Automatic hardware detection • Contains the RAID configuration utility • Provides device drivers based on the server model and detected devices • Downloads device drivers from the ThinkServer EasyStartup DVD according to the operating system or add-on device • Selectable partition size and file system type • Support for multiple operating systems • Ability to install the operating system and device drivers in an unattende
specific version of the program; and click User Guide to view the various functions and learn how to use the program. • Before using the ThinkServer EasyStartup program to install an operating system, ensure that any external storage devices and fiber channels are configured correctly.
• On the Microsoft Windows Server® 2003 operating system, you might need to add the Uniform Resource Locator (URL) for the ThinkServer EasyStartup program Web page to the trusted Web site list so that the page can open correctly. You can do the following when using the ThinkServer EasyStartup program on a Windows operating system. For detailed information, refer to the help system. • View a general introduction to your ThinkServer server model and the specific server configuration information.
• RAID 0: block-level striping without parity or mirroring Simple stripe sets are normally referred to as RAID 0. RAID 0 uses striping to provide high data throughput, especially for large files in an environment that does not require fault tolerance. RAID 0 has no redundancy and it provides improved performance and additional storage without fault tolerance. Any drive failure destroys the array and the likelihood of failure increases with more drives in the array.
Configuring RAID using the ThinkServer EasyStartup program The ThinkServer EasyStartup program simplifies the process of configuring supported RAID and installing supported Windows and Linux operating systems and device drivers on your server. The user guide for the program can be accessed directly from the program interface.
This status indicates that more than one hard disk drive in the RAID array cannot be synchronized or have failed. You need to replace the failing hard disk drives and rebuild the data. See “Installing or replacing a hot-swap hard disk drive” on page 148 and “Rebuilding a physical drive” on page 76. • Offline This status indicates that the RAID array has failed and cannot be rebuilt. You need to create a new RAID array. See “Creating, adding, or deleting a RAID array” on page 74.
The following table shows the various menus and items in the LSI Software RAID Configuration Utility program. On each menu, press the Enter key to show selectable options and select a desired option by using up and down arrow keys or type desired values from the keyboard directly. Table 1. LSI Software RAID Configuration Utility program menu items Menu item Configure Submenu item Comments Easy Configuration Create physical arrays. An array will automatically become a virtual drive.
• If you want to delete the existing RAID array, exit the program and back up all your data on the hard disk drives. After backing up all your data, enter the program main interface and select Clear Configuration. Select Yes when prompted and follow the instructions on the screen. Attention: Deleting an existing RAID array erases all data on the array. Ensure that you back up all data before deleting the RAID array.
• If you want to set a hot-spare drive right after the configuration, select Objects ➙ Physical Drive from the program main interface. Then, select the hard disk drive that you want to set as a hot-spare drive and press Enter. A submenu is displayed. Select Make Hot Spare from the submenu and then select Yes when prompted to set the hard disk drive as a hot-spare drive.
To run a consistency check using the LSI Software RAID Configuration Utility program, do the following: 1. Start the LSI Software RAID Configuration Utility program. See “Starting the LSI Software RAID Configuration Utility program” on page 73. 2. On the main interface of the program, select Check Consistency and follow the instructions on the screen. The consistency check rate is the rate at which consistency check operations are run on a system.
Some server models come with a RAID card to provide advanced SATA/SAS hardware RAID functions. You also can purchase a supported RAID card from Lenovo and install it into the server. See “RAID card” on page 36. The RAID card provides the WebBIOS Configuration Utility program to help you configure RAID independently of the operating system.
Note: Before distributing the firmware updates to a server, ensure that your server can restart successfully without encountering hardware problems. 1. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to locate the Firmware Updater program. 2. Download the ISO image for the Firmware Updater program and the installation instructions in a TXT file. 3. Use any CD or DVD burning software to create a bootable disc with the ISO image. 4.
80 ThinkServer RD430 User Guide
Chapter 6. Installing, removing, or replacing hardware This chapter provides instructions on how to install, remove, or replace hardware for your server. This chapter contains the following items: • “Guidelines” on page 81 • “Removing the server cover” on page 83 • “Removing and reinstalling the front bezel” on page 85 • “Installing, removing, or replacing hardware” on page 86 • “Completing the parts replacement” on page 174 For a list of the ThinkServer options, go to: http://www.lenovo.
• Have a small flat-blade screwdriver available. • You do not have to turn off the server to install or replace a hot-swap redundant power supply, hot-swap hard disk drives, or hot-plug USB devices. However, you must turn off the server before performing any steps that involve installing, removing, or replacing adapter cables or non-hot-swap devices or components. • To view the LEDs on the system board and internal components, leave the server connected to power.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground. – When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector-outside shells on these systems. – Use the ground prong of the ac plug on ac-operated servers.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Note: Depending on the model, your server might look slightly different from the illustrations in this topic. To remove the server cover, do the following: 1. Remove all media from the drives. Then, turn off all attached devices and the server. 2. Disconnect all power cords from electrical outlets. 3.
6. Fully open the cover latch 1 and slide the server cover to the rear until it is disengaged from the chassis. Then, lift the server cover off the chassis and set it aside. Note: It is recommended that you wait three to five minutes to let the server cool before removing the server cover. Figure 43. Removing the server cover Attention: For proper cooling and airflow, install the server cover before turning on the server.
1. Remove the three screws 1 that secure the front bezel and then pivot the front bezel outward to remove it from the chassis. Figure 44. Removing the front bezel 2. To reinstall the front bezel, align the tabs on the bottom edge of the front bezel with the corresponding holes in the chassis. Then, pivot the front bezel inward until it snaps into position and the three screw holes 1 in the top edge of the front bezel are aligned with the corresponding holes in the top of the chassis.
Notes: • Use only parts provided by Lenovo. • Depending on the model, your server might look slightly different from the illustrations in this topic. The EMI integrity and cooling of the server are protected by having all drive bays and PCI card slots covered or occupied. When you install an internal drive or a PCI card, save the EMI shield or dummy tray from the drive bay or save the PCI card slot bracket in the event that you later remove the device.
5. Disconnect the following signal cables from the signal cable connectors on the backplane for server models with 12 3.5-inch hard disk drive bays. • Signal cable for the front controls and LEDs on the right rack handle • Signal cable for the front USB connectors on the left rack handle Figure 46. Disconnecting the rack handle signal cables from the backplane 6. On each side of the server, remove the screw that secures the rack handle and then remove the rack handle from the chassis.
a. On each side of the server, insert the signal cable of the rack handle into the hole 1 in the chassis and then push the signal cable through the hole into the chassis. When the signal cable is protruding from the crack between the side edge of the backplane and the inner side of the chassis, hold the signal cable from the rear and carefully pull it into the chassis until it is stopped by the rack handle. b. Insert the two small tabs on the rack handle into the corresponding holes 2 in the chassis.
c. Connect the signal cable of each rack handle to the corresponding signal cable connector on the backplane for server models with 12 3.5-inch hard disk drive bays. Figure 49. Connecting the rack handle signal cables to the backplane 8. Go to “Completing the parts replacement” on page 174. Removing and reinstalling the rack handles for server models with eight 3.5-inch hard disk drive bays and server models with 2.
2. To reinstall the rack handles, insert the small tab 1 on the rack handle into the hole 2 in the chassis. Then, align the screw hole in the rack handle with the corresponding hole in the chassis and install the screw to secure the rack handle on each side of the server. Figure 51. Installing the rack handles Removing and reinstalling the cooling shroud Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 81.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 83. 4. Locate the cooling shroud and lift it out of the server. Figure 52. Removing the cooling shroud 5.
Attention: For proper cooling and airflow, reinstall the cooling shroud before turning on the server. Operating the server with the cooling shroud removed might damage server components. Removing and reinstalling the left cage Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 81. This topic provides instructions on how to remove and reinstall the left cage.
8. Remove the two screws that secure the left cage and then slide the left cage out of the front of the chassis. Figure 54. Removing the left cage 9. To reinstall the left cage, carefully route the cables from the left cage through the left cage hole in the front and then slide the left cage into the chassis until it snaps into position. Figure 55.
10. Ensure that the two screw holes in the rear of the left cage are aligned with the corresponding holes in the chassis. Then, install the two screws to secure the left cage in position. Figure 56. Installing the screws to secure the left cage 11. If your server has a slim optical drive installed, reconnect the signal cable and the power cable to the rear of the slim optical drive. 12. Refer to your note to reconnect other cables to the system board.
For more information about the memory modules in your specific server model, use the Setup Utility program. See “Viewing information in the Setup Utility program” on page 59. For a list of the supported ThinkServer memory module options, go to: http://www.lenovo.com/thinkserver The following illustration shows the locations of all memory slots on a system board that has two microprocessors (also known as CPUs) installed. Figure 57.
The following table explains the memory module installation rules for servers that have only one microprocessor (CPU1) installed. The “X” mark indicates the memory slot(s) into which the memory module(s) should be installed in different situations. Note: All memory modules to be installed on a server must be the same type (LV RDIMM, RDIMM, or UDIMM) with the same rank, voltage, and frequency. Figure 58. CPU1 DIMMs Table 2.
The following table explains the memory module installation rules for servers that have two microprocessors (CPU1 and CPU2) installed. The “X” mark indicates the memory slot(s) into which the memory module(s) should be installed in different situations. Note: All memory modules to be installed on a server must be the same type (LV RDIMM or RDIMM) with the same rank, voltage, and frequency. Figure 59. CPU1 DIMMs and CPU2 DIMMs Table 3.
To install a memory module, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover.
9. Position the new memory module over the memory slot. Ensure that the notch 1 on the new memory module is aligned with the key 2 in the memory slot. Then, press the new memory module straight down into the memory slot until the retaining clips close and the new memory module snaps into position. Note: If there is a gap between the memory module and the retaining clips, the memory module has not been correctly installed.
6. Disconnect any cables that might impede your access to the memory slots. 7. Locate the memory module that you want to remove and open the retaining clips on both ends of the memory slot. Then, grasp the memory module by its edges and carefully pull it straight up to remove it from the memory slot. Figure 62. Removing a memory module 8. If you are instructed to return the old memory module, follow all packaging instructions and use any packaging materials that are supplied to you for shipping.
• Depending on the specific type, your RAID card might look different from the illustrations in this topic. • Use any documentation that comes with the RAID card and follow those instructions in addition to the instructions in this topic. To install the RAID card, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2.
8. Note the dotted lines in the following illustration to properly position the new RAID card near the longer PCI Express card slot on the riser card assembly 1. Then, carefully press the new RAID card straight into the slot until it is securely seated and its bracket also is secured by the riser card assembly 1. Figure 64. Installing the RAID card 9.
• The RAID card is extremely sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 82 first and carefully perform the operation. • Depending on the specific type, your RAID card might look different from the illustrations in this topic. • Use any documentation that comes with the RAID card and follow those instructions in addition to the instructions in this topic. To remove the RAID card, do the following: 1.
11. If you are instructed to return the old RAID card, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the removal procedure, go to “Completing the parts replacement” on page 174. Then, configure RAID for your server. See “Configuring RAID” on page 70.
6. Locate the RAID 5 key connector on the ThinkServer RAID 500 Adapter and then carefully insert the TR 500 Key into the connector. If necessary, you can remove the ThinkServer RAID 500 Adapter first, install the TR 500 Key on it, and then reinstall the ThinkServer RAID 500 Adapter. See “Installing or removing the RAID card” on page 101. Note: Ensure that the TR 500 Key is securely seated on the ThinkServer RAID 500 Adapter. Figure 66.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 83. 4.
alternative to using an uninterruptible power supply, and a second level of fault tolerance when used in conjunction with an uninterruptible power supply. The temperature of the TR 700 Battery is generally 15-20°C (59-68°F) higher than the ambient temperature during fast charge. Therefore, to complete a recharge cycle, the ambient temperature should be lower than 55°C (131°F).
8. Position the TR 700 Battery above the ThinkServer RAID 700 Adapter so that the board-to-board connector 1 on the bottom of the TR 700 Battery is aligned with the connector 2 on the ThinkServer RAID 700 Adapter; and the three mounting studs on the bottom of the TR 700 Battery are aligned with the corresponding holes in the ThinkServer RAID 700 Adapter. Carefully press the TR 700 Battery onto the ThinkServer RAID 700 Adapter until the two connectors ( 1 and 2 ) are firmly joined.
• Use any documentation that comes with the TR 700 Battery and follow those instructions in addition to the instructions in this topic. To remove the TR 700 Battery, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2.
Notes: • The server must have a RAID card and an expander card installed to support more than eight hard disk drives. • The expander card is extremely sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 82 first and carefully perform the operation. Installing the expander card Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 81.
6. There are two PCI Express card slots on the riser card assembly 1 and the shorter one is for installing the expander card. Remove the slot bracket for the shorter slot and store it in the event that you later remove the expander card and need the bracket to cover the place. Note: Ensure that you install the RAID card and connect two mini-SAS to mini-SAS signal cables to the RAID card before installing the expander card. Figure 70. Removing a PCI Express card slot bracket 7.
9. Connect cables depending on your specific server configuration. See “Mini-SAS to mini-SAS signal cable connections” on page 42. 10. Reinstall the riser card assembly 1. See “Replacing the riser card assembly 1” on page 159. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation, go to “Completing the parts replacement” on page 174. Then, you might need to configure RAID for your server. See “Configuring RAID” on page 70.
6. There are two PCI Express card slots on the riser card assembly 1 and the expander card is installed in the shorter slot. Disconnect cables from the expander card. Then, grasp the expander card by its edges and carefully pull it out of the PCI Express card slot. Note: The expander card might fit tightly into the PCI Express card slot. If necessary, alternate moving each side of the expander card a small and equal amount until it is completely removed from the slot. Figure 72.
This topic provides instructions on how to install an Ethernet card. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Depending on the specific type, the Ethernet card might look different from the illustrations in this topic. • Use any documentation that comes with the Ethernet card and follow those instructions in addition to the instructions in this topic. To install an Ethernet card, do the following: 1.
Note: Depending on the specific type, the Ethernet card and its bracket might look different from the following illustrations. a. Carefully remove the screws that secure the Ethernet card and then remove the full-height bracket from the Ethernet card. Figure 74. Removing the full-height bracket from the Ethernet card b.
8. Position the Ethernet card near the PCI Express card slot for which you have removed the slot bracket. Then, carefully press the Ethernet card straight into the slot until it is securely seated and its bracket also is secured by the riser card assembly 2. Figure 76. Installing an Ethernet card 9. Depending on the type of the Ethernet card, you might need to connect any required cables. Refer to the documentation that comes with the Ethernet card for specific information. 10.
This topic provides instructions on how to remove an Ethernet card. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Depending on the specific type, the Ethernet card might look different from the illustration in this topic. • Use any documentation that comes with the Ethernet card and follow those instructions in addition to the instructions in this topic. To remove an Ethernet card, do the following: 1.
8. If you are instructed to return the old Ethernet card, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the removal procedure, go to “Completing the parts replacement” on page 174.
6. Insert one side of the TR 300 Key under one of the retaining clips on the iButton socket. Then, carefully press the other side of the TR 300 Key straight down until it snaps into position and is secured by the two retaining clips on the iButton socket. Figure 78. Installing the TR 300 Key 7. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1” on page 159.
This topic provides instructions on how to remove the TR 300 Key if your server has one installed on the system board. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • If you remove the TR 300 Key, the onboard SAS software RAID 5 will be disabled. • Use any documentation that comes with the TR 300 Key and follow those instructions in addition to the instructions in this topic.
5. Open the retaining clip 1 on the iButton socket to release the TR 300 Key and then completely remove the TR 300 Key from the iButton socket. Figure 79. Removing the TR 300 Key 6. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1” on page 159. 7. If you are instructed to return the old TR 300 Key, follow all packaging instructions and use any packaging materials that are supplied to you for shipping.
Installing or removing the ThinkServer Management Module Premium This topic provides instructions on how to install or remove the ThinkServer Management Module Premium (TMM Premium). The TMM Premium offers convenient, remote KVM access and control through the LAN or Internet. You can use the TMM Premium to gain location-independent remote access to respond to critical incidents and to undertake necessary maintenance.
5. Locate the TMM Premium connector on the system board and then insert the TMM Premium into the TMM Premium connector. Note: Ensure that the TMM Premium is securely seated on the system board. Figure 80. Installing the TMM Premium What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation, go to “Completing the parts replacement” on page 174.
Notes: • If you remove the TMM Premium, the iKVM function for server remote management will be unavailable. • Use any documentation that comes with the TMM Premium and follow those instructions in addition to the instructions in this topic. • Depending on the model, your server might look slightly different from the illustration in this topic. To remove the TMM Premium, do the following: 1. Remove all media from the drives and turn off all attached devices and the server.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the removal procedure, go to “Completing the parts replacement” on page 174. Installing or removing the ThinkServer Trusted Platform Module This topic provides instructions on how to install or remove the ThinkServer Trusted Platform Module (TPM). The TPM is a security chip designed by the Trusted Computing Group (TCG) to provide a hardware method of data encryption.
6. Insert the TPM into the TPM connector on the system board. Figure 82. Installing the TPM 7. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1” on page 159. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation, go to “Completing the parts replacement” on page 174. Then, you can configure the TPM function in the Setup Utility program.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • If you remove the TPM, the TPM function will be unavailable. • Use any documentation that comes with the TPM and follow those instructions in addition to the instructions in this topic. • Depending on the model, your server might look slightly different from the illustration in this topic. To remove the TPM, do the following: 1.
5. Remove the TPM installed on the TPM connector by lifting it straight up. Note: Carefully handle the TPM by its edges. Figure 83. Removing the TPM 6. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1” on page 159. 7. If you are instructed to return the old TPM, follow all packaging instructions and use any packaging materials that are supplied to you for shipping.
This topic provides instructions on how to install or replace a hot-swap redundant power supply. The hot-swap redundant power supply adds a second source of power to the server. When the server is populated with two hot-swap redundant power supplies, it can withstand a power loss from either power supply. This helps you avoid significant interruption to the operation of the server when a power supply fails. You can replace the failing hot-swap redundant power supply without turning off the server.
• If you are installing a hot-swap redundant power supply, locate the bay for the power supply in the rear of your server. Insert a finger into the hole in the metal shield that protects the bay, press the tab 1 in the direction as shown, and then pull the shield out of the chassis. Store the shield in the event that you later remove the power supply and need the shield to cover the bay. Figure 84.
2. If you are replacing a hot-swap redundant power supply, press the release tab 1 in the direction as shown and carefully pull the handle 2 at the same time to slide the failing hot-swap redundant power supply out of the chassis. Figure 85. Removing a hot-swap redundant power supply 3. Touch the static-protective package that contains the new hot-swap redundant power supply to any unpainted surface on the outside of the server. Then, remove the new hot-swap redundant power supply from the package. 4.
5. Connect the power cord to the power cord connector on the new hot-swap redundant power supply. Then, check the status LED near the power cord connector. When the LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly. When the LED is lit in amber, it indicates that the hot-swap redundant power supply is likely to fail or has failed. Reinstall the new hot-swap redundant power supply to see if the problem can be solved.
6. If you are replacing a heat sink, remove the four screws that secure the heat sink to the system board. It is recommended that you carefully remove the four screws from the system board using the following method to avoid any possible damage to the system board. a. Partially remove screw 1 , then completely remove screw 3 , and then return to screw 1 and completely remove it. b. Partially remove screw 2 , then completely remove screw 4 , and then return to screw 2 and completely remove it.
10. Install the four screws to secure the new heat sink on the system board. It is recommended that you carefully install the four screws using the following method to avoid any possible damage to the system board. a. Partially tighten screw 1 , then firmly tighten screw 3 , and then return to screw 1 and firmly tighten it. Do not over-tighten the screws. b. Partially tighten screw 2 , then firmly tighten screw 4 , and then return to screw 2 and firmly tighten it. Do not over-tighten the screws. Figure 88.
Depending on the model, your server might come with one or two microprocessors. For server models with one microprocessor, the microprocessor is installed in the microprocessor socket 1 and the microprocessor socket 2 is protected by a plastic socket cover. You can purchase a microprocessor option kit from Lenovo and install the second microprocessor to expand system capabilities. CAUTION: Turn off the server and wait three to five minutes to let the server cool before removing the server cover.
6. Gently press down the small handle on the microprocessor socket and then pull the handle a little bit outward to release it from the secured position. Then, pivot the handle upward to the fully open position. Then, gently press the microprocessor retainer to open it. Figure 89. Opening the small handle and microprocessor retainer 7. Ensure that the small handle and the microprocessor retainer are in the fully open position. Then, remove the plastic microprocessor socket cover.
9. Remove the protective cover that protects the gold contacts on the bottom of the new microprocessor. Do not touch the pins on the microprocessor socket and the gold contacts on the bottom of the new microprocessor. Figure 91. Do not touch the pins 10. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align the notches 1 on it with the tabs 2 in the microprocessor socket. Then, carefully lower the new microprocessor straight down into the microprocessor socket.
11. Carefully close the microprocessor retainer. Then, carefully close the small handle to lock the retainer into position and secure the new microprocessor in the socket. Figure 93. Securing the microprocessor in the socket 12. Install the new heat sink that comes with the microprocessor option kit. See “Installing or replacing a heat sink” on page 133. What to do next: • To work with another piece of hardware, go to the appropriate section.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Ensure that the new microprocessor is the correct type your server supports. See “Features” on page 8. When two microprocessors are installed, both must have the same core voltage and core speed. • Use any documentation that comes with the microprocessor option kit and follow those instructions in addition to the instructions in this topic.
7. Ensure that the small handle and the microprocessor retainer are in the fully open position. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor socket. Place the old microprocessor on a static-protective surface. Notes: • Do not touch the gold contacts on the bottom of the microprocessor. • Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Figure 95.
10. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align the notches 1 on it with the tabs 2 in the microprocessor socket. Then, carefully lower the new microprocessor straight down into the microprocessor socket. Note: The small triangle 3 on one corner of the new microprocessor is the microprocessor orientation indicator. The new microprocessor is in the correct orientation when this indicator faces the beveled corner 4 of the microprocessor socket.
11. Carefully close the microprocessor retainer. Then, carefully close the small handle to lock the retainer into position and secure the new microprocessor in the socket. Figure 98. Securing the microprocessor in the socket 12. Reinstall the heat sink. See “Installing or replacing a heat sink” on page 133. 13. If you are instructed to return the old microprocessor, follow all packaging instructions and use any packaging materials that are supplied to you for shipping.
CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
• If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear of the optical drive. Press the rear of the retaining bracket 1 in the direction as shown and push the optical drive from the rear until it is projected from the front of the chassis. Then, hold the optical drive from the front and completely slide it out of the chassis. Figure 99. Removing the optical drive for server models with 3.5-inch hard disk drives Figure 100.
7. Remove the retaining bracket from the old optical drive or the dummy optical drive tray. Then, install it on the side of the new optical drive. Figure 101.
8. Slide the new optical drive with the retaining bracket into the drive bay from the front until it snaps into position. Figure 102. Installing the optical drive for server models with 3.5-inch hard disk drives Figure 103. Installing the optical drive for server models with 2.5-inch hard disk drives Chapter 6.
9. Connect the signal cable 1 and the power cable 2 to the rear of the new optical drive. Figure 104. Connecting cables to the rear of the optical drive 10. If you are instructed to return the old optical drive, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 174.
• For hard disk drives with different capacities, install the hard disk drives following the order of the hard disk drive bays as well as the order from the lowest capacity to the highest capacity. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Depending on the model, your server might look slightly different from the illustrations in this topic.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Figure 106. Opening the handle of a 2.5-inch hot-swap hard disk drive or dummy tray 2. Pull the handle and carefully slide the hot-swap hard disk drive or the dummy tray out of the front of the chassis. Figure 107. Removing the 3.
Figure 108. Removing the 2.5-inch hot-swap hard disk drive or dummy tray 3. Touch the static-protective package that contains the new hot-swap hard disk drive to any unpainted surface on the outside of the server. Then, take the new hot-swap hard disk drive out of the package. Note: Do not touch the circuit board on the hard disk drive. 4. Slide the new hot-swap hard disk drive into the drive bay from the front until it snaps into position and then completely close the handle. Figure 109.
Figure 110. Installing the 2.5-inch hot-swap hard disk drive 5. Check the hot-swap hard disk drive status LEDs to ensure that the hard disk drive is operating correctly. You might have to restart the server for the newly installed hard disk drive to be recognized. See “Hot-swap hard disk drive status LEDs” on page 35. If the hard disk drive is faulty, you need to reinstall or replace it until it is operating correctly. 6.
Replacing the backplane for server models with eight 3.5-inch hard disk drive bays Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 81. This topic provides instructions on how to replace the backplane for server models with eight 3.5-inch hard disk drive bays. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
8. Carefully lift the backplane straight up a little bit so that the small hooks 1 on the chassis are aligned with the corresponding holes in the backplane. Then, slowly and carefully move the backplane to the rear of the chassis until the hooks 1 pass through the holes in the backplane and then completely remove the backplane out of the chassis. Figure 112. Removing the backplane for server models with eight 3.5-inch hard disk drive bays 9.
11. Press the buttons 1 to put the latches on the chassis to the closed position so that the latches secure the new backplane in place. Figure 114. Securing the backplane for server models with eight 3.5-inch hard disk drive bays 12. Reinstall all the hot-swap hard disk drives and dummy trays (if any) in the hard disk drive bays. See “Installing or replacing a hot-swap hard disk drive” on page 148. 13. Refer to your note to connect the cables to the new backplane. 14.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 83. 4. Locate the backplane. See “Components of server models with 12 3.5-inch hard disk drive bays” on page 33. 5. Remove all the installed 3.
10. Reinstall all the hot-swap hard disk drives and dummy trays (if any) in the hard disk drive bays. See “Installing or replacing a hot-swap hard disk drive” on page 148. 11. Refer to your note to connect the cables to the new backplane. 12. If you are instructed to return the old hot-swap hard disk drive backplane, follow all packaging instructions and use any packaging materials that are supplied to you for shipping.
7. Remove the three screws that secure the backplane and then carefully lift the backplane out of the chassis. Figure 117. Removing the backplane for server models with 2.5-inch hard disk drive bays 8. Touch the static-protective package that contains the new hot-swap hard disk drive backplane to any unpainted surface on the outside of the server. Then, remove the new backplane from the package. Note: Carefully handle the backplane by its edges.
9. Note the orientation of the new backplane. Carefully press the new backplane straight down into the chassis so that it is secured in place by the tabs 1 on the chassis and the three screw holes in the new backplane are aligned with the corresponding holes in the chassis. Then, install the screws to secure the new backplane in place. Figure 118. Installing the backplane for server models with 2.5-inch hard disk drive bays 10.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 83. 4.
11. Position the new riser card assembly 1 on the chassis and align it with the riser card assembly 1 slot on the system board and align the rear of it with the corresponding rail guides in the rear of the chassis. Then, carefully press the new riser card assembly 1 straight down into the chassis until it is fully seated. Note: If there is any PCI Express card installed on the riser card assembly 1, carefully fit the PCI Express card into the chassis and properly route any cables from the card. Figure 120.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 83. 4. Locate the riser card assembly 2. See “Server components” on page 31. 5. Grasp the riser card assembly 2 by its edges and carefully lift it straight up and off the chassis.
10. Position the new riser card assembly 2 on the chassis and align it with the riser card assembly 2 slot on the system board and align the rear of it with the corresponding rail guides in the rear of the chassis. Then, carefully press the new riser card assembly 2 straight down into the chassis until it is fully seated. Note: If there is any PCI Express card installed on the riser card assembly 2, carefully fit the PCI Express card into the chassis and properly route any cables from the card. Figure 122.
Notes: • The front panel board is extremely sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 82 first and carefully perform the operation. • Depending on the model, your server might look slightly different from the illustrations in this topic. Replacing the front panel board for server models with eight 3.
8. Carefully position the new front panel board on the chassis so that the front controls, connectors, and LEDs are through the corresponding holes in the front bezel and the two screw holes in the new front panel board are aligned with the corresponding mounting studs on the chassis. Then, install the screws to secure the front panel board in place. Figure 124. Installing the front panel board for server models with eight 3.5-inch hard disk drive bays 9.
8. Disconnect the front panel cable and the front panel USB cable from the rear of the front panel board. 9. Remove the two screws that secure the front panel board and then carefully remove the front panel board from the left cage. Figure 125. Removing the front panel board from the left cage of server models with 2.5-inch hard disk drive bays 10. Touch the static-protective package that contains the new front panel board to any unpainted surface on the outside of the server.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 174. Replacing the diagnostic module This topic provides instructions on how to replace the diagnostic module. For detailed information about the diagnostic module, see “Diagnostic module” on page 23. This topic contains the following items: • “Replacing the diagnostic module for server models with eight 3.
6. Press the release tab 1 in the direction as shown and then push the diagnostic module out of the front of the chassis. Figure 127. Removing the diagnostic module for server models with eight 3.5-inch hard disk drive bays 7. Touch the static-protective package that contains the new diagnostic module to any unpainted surface on the outside of the server. Then, take the new diagnostic module out of the package. 8.
10. If you are instructed to return the old diagnostic module, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 174. Replacing the diagnostic module for server models with 2.
12. Slide the new diagnostic module into the cage from the front until it snaps into position. Figure 130. Installing the diagnostic module into the left cage of server models with 2.5-inch hard disk drive bays 13. Connect the diagnostic module cable to the rear of the new diagnostic module. 14. Reinstall the front panel board. See “Replacing the front panel board for server models with 2.5-inch hard disk drive bays” on page 165. 15. Reinstall the left cage and then reconnect all cables.
To replace a system fan, do the following: 1. Remove the server cover. See “Removing the server cover” on page 83. Note: The system fans are hot-swap and you can replace a failing system fan without turning off the server. 2. Do the following to locate the failing system fan: • If your server comes with an Intelligent Diagnostics Module Premium, you can view the system fan error LEDs on the panel of the module to locate the failing system fan.
5. Position the new system fan above the place for the removed failing system fan so that the system fan connector on the bottom of the new system fan is facing the rear of the chassis. Then, press the new system fan straight down until it is seated into place. Note: Install a new system fan as soon as you remove the failing one. Figure 132. Installing the system fan 6.
DANGER Danger of explosion if battery is incorrectly replaced. When replacing the lithium coin cell battery, use only the same or an equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations.
5. Remove the old system board battery. Figure 133. Removing the system board battery 6. Install a new system board battery. Figure 134. Installing the system board battery 7. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1” on page 159. 8. Dispose of the old system board battery as required by local ordinances or regulations. What to do next: • To work with another piece of hardware, go to the appropriate section.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Note: Depending on the model, your server might look slightly different from the illustrations in this topic. To reinstall the server cover and reconnect cables to your server, do the following: 1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your server. 2.
3. If you have removed the cooling shroud, reinstall it. See “Removing and reinstalling the cooling shroud” on page 91. 4. For server models with 2.5-inch hot-swap hard disk drive bays, if you have removed the front bezel, reinstall it. See “Removing and reinstalling the front bezel” on page 85. 5. Ensure that the cover latch is in the open position. Place the server cover above the chassis so that the cover latch is aligned with the cover latch slot in the chassis.
7. Install the server into a rack cabinet using the rail kit that comes with the server. See the Rack Installation Instructions that comes with the server. 8. Reconnect external cables and power cord(s) to the server. See “Rear view of the server” on page 26 to identify the connectors on the rear panel of the server. Attention: To avoid component damage, connect the power cord(s) last. Note: In most areas of the world, Lenovo requires the return of the defective CRU.
178 ThinkServer RD430 User Guide
Chapter 7. Troubleshooting and diagnostics This chapter provides information about basic troubleshooting and diagnostic methods to help you solve problems that might occur in the server. If you cannot diagnose and correct a problem by using the information in this chapter, see Chapter 8 “Getting information, help, and service” on page 185 for additional troubleshooting resources.
The TMM implements the SEL as specified in the IPMI 2.0 specification. The SEL is accessible regardless of the system power state through the TMM in-band and out-of-band interfaces. For more information about viewing the SEL, refer to the ThinkServer Management Module User Guide, which is available for download at: http://www.lenovo.com/ThinkServerUserGuides Basic troubleshooting tables Use the basic troubleshooting information to find solutions to problems that have definite symptoms.
• If an action step is preceded by “(Trained service technician only),” this action step is reserved for a trained service technician and must be performed only by a trained service technician. Action Symptom The internal optical drive is not recognized. 1. Ensure that: • The related cables and connectors are not damaged and the connector pins are not bent.
Notes: • If you are instructed to remove, install, or replace any CRUs, refer to the related procedure in Chapter 6 “Installing, removing, or replacing hardware” on page 81. • The status LEDs on each hot-swap hard disk drive help you easily identify a problem. See “Hot-swap hard disk drive status LEDs” on page 35. Action Symptom A newly installed hot-swap hard disk drive is not recognized. 1. Ensure that the drive is installed into the correct drive bay. 2. Restart the server. 3.
• If an action step is preceded by “(Trained service technician only),” this action step is reserved for a trained service technician and must be performed only by a trained service technician. Action Symptom The amount of system memory that is displayed is less than the total capacity of the installed physical memory modules and you suspect a memory module problem. 1. Ensure that: • All memory modules are the correct type supported by the server. See “Memory module installation rules” on page 95.
Action Symptom 3. Replace the mouse or pointing device. A USB device does not work. 1. Ensure that: • The USB cable is securely connected to the server. If the USB device is connected to a USB hub, disconnect the device from the hub and connect it directly to the server. • The device drivers are installed correctly. • The USB controller is enabled in the Setup Utility program. See “Using the Setup Utility program” on page 59. 2. Restart the server. 3. Replace the USB device.
Chapter 8. Getting information, help, and service This chapter contains information about help, service, and technical assistance for products manufactured by Lenovo and where to go for additional information about Lenovo and Lenovo products. Information resources You can use the information in this topic to access useful resources relating to your needs when using the product.
• Diagnostic solutions • Product and service warranty • Product and parts details • User guides and manuals • Knowledge base and frequently asked questions Help and service This topic contains information about obtaining help and service. Before you call Before you call, do the following to try to solve the problem by yourself: • Check all cables to ensure that they are connected. • Check the power switches to ensure that the system and optional devices are turned on.
For the warranty type and duration for your product, refer to the Warranty and Support Information on the documentation DVD that comes with you server. You must retain your proof of purchase to obtain warranty service. For warranty service, consult the worldwide Lenovo Support telephone list. Telephone numbers are subject to change without notice. The most up-to-date telephone list for Lenovo Support is always available on the Web site at http://www.lenovo.com/support/phone.
188 ThinkServer RD430 User Guide
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks Lenovo, the Lenovo logo, and ThinkServer are trademarks of Lenovo in the United States, other countries, or both. Intel and Intel Xeon are trademarks of Intel Corporation in the United States, other countries, or both. Internet Explorer, Microsoft, Windows, and Windows Server are trademarks of the Microsoft group of companies. Linux is a registered trademark of Linus Torvalds. Other company, product, or service names may be trademarks or service marks of others.
Battery return program This product may contain a lithium or lithium ion battery. Consult your user manual or service manual for specific battery information. The battery must be recycled or disposed of properly. Recycling facilities may not be available in your area. For information on disposal or batteries outside the United States, go to http://www.lenovo.com/recycling or contact your local waste disposal facility.
Perchlorate Material - special handling may apply, See http://www.dtsc.ca.gov/hazardouswaste/perchlorate Particulate contamination Attention: Airborne particulates (including metal flakes or particles) and reactive gases acting alone or in combination with other environmental factors such as humidity or temperature might pose a risk to the server that is described in this document.
applied to various products to indicate that the product is not to be thrown away, but rather reclaimed upon end of life per this Directive.
potenziale effetto della EEE sull'ambiente e sulla salute umana dovuto alla presenza di sostanze pericolose. Per ulteriori informazioni sulla WEEE visitare il sito: http://www.lenovo.com/recycling. A marca REEE (Resíduos de Equipamentos Eléctricos e Electrónicos) aplica-se apenas aos Estados Membros da União Europeia e à Noruega. Os aparelhos eléctricos deverão ser identificados em conformidade com a Directiva Europeia 2002/96/CE relativa a REEE (Resíduos de Equipamentos Eléctricos e Electrónicos).
utstyr (WEEE). Direktivet fastsetter rammene for retur og resirkulering av brukt utstyr innenfor EU. Dette merket benyttes på forskjellige produkter for å angi at produktet ikke må kastes, men må behandles i henhold til dette direktivet ved slutten av produktets levetid.
German Ordinance for Work gloss statement The product is not suitable for use with visual display work place devices according to clause 2 of the German Ordinance for Work with Visual Display Units. Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne § 2 der Bildschirmarbeitsverordnung geeignet. Export classification notice This product is subject to the United States Export Administration Regulations (EAR) and has an Export Classification Control Number (ECCN) of 4A994.b.
European Union - Compliance to the Electromagnetic Compatibility Directive This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the installation of option cards from other manufacturers.
Nach dem EMVG: „Geräte dürfen an Orten, für die sie nicht ausreichend entstört sind, nur mit besonderer Genehmigung des Bundesministers für Post und Telekommunikation oder des Bundesamtes für Post und Telekommunikation betrieben werden. Die Genehmigung wird erteilt, wenn keine elektromagnetischen Störungen zu erwarten sind.“ (Auszug aus dem EMVG, Paragraph 3, Abs. 4).
Index A installing 98 removing 100 DIMM status LED 24, 26 documentation using 185 about RAID 70 Advanced menu Setup Utility program 60 advanced SATA/SAS hardware RAID configuring 77 ambient temperature limit LED 24, 26 E B BIOS and TMM update utilities software 12 BMC status LED 55 Boot Manager menu Setup Utility program 62 Boot Options menu Setup Utility program 62 C cable connection 42 configuring Ethernet controllers 78 server 59 configuring RAID advanced SATA/SAS hardware RAID 77 ThinkServer RAID 3
German gloss statement 196 getting help 185 getting information 185 getting service 185 guidelines 81 H hardware installing 81 removing 81 replacing 81 heat sink installing 133 replacing 133 help, getting 185 hot-spare drive setting 75 hot-swap hard disk drive installing 148 replacing 148 hot-swap hard disk drive backplane locations 38 replacing 152 hot-swap hard disk drive status LED 35 hot-swap hard disk drive status LEDs locations 35 hot-swap redundant power supply installing 129 replacing 129 hot-swap
installation rules 95 installing 98 removing 100 memory module installation guidelines 95 memory module status LED 24, 26 microprocessor features 8 installing 135 replacing 139 microprocessor status LED 24, 26 N NIC status LED 19, 22 O optical drive installing 143 replacing 143 option completing the replacement 174 P particulate contamination 192 parts replacement, completing 174 password considerations 63 setting, changing, deleting 63 Setup Utility program 63 physical drive rebuilding 76 power status
S Save & Exit menu Setup Utility program 62 Security menu Setup Utility program 61 server components locations 31 server configuration updating 177 server cover installing 174 removing 83 server documentation 2 Server Management menu Setup Utility program 61 server package 7 server setup road map 5 service, getting 185 setting hot-spare drive 75 setting, changing, deleting password 63 Setup Utility program Ethernet connector 0 65 exiting 65 interface 60 password 63 starting 59 TPM 64 using 59 software 12 sp
system event log 179 ThinkServer EasyStartup program problems troubleshooting procedure 179 turning off the server 57 turning on the server 57 TÜV gloss statement 196 180 U updating firmware 78 server configuration 177 the BIOS 66 updating or recovering the BIOS 65 using documentation 185 EasyUpdate Firmware Updater program 78 Lenovo ThinkServer EasyManage program 79 passwords 63 Setup Utility program 59 ThinkServer EasyStartup program 67 V video subsystem features 9 viewing information Setup Utility pro
204 ThinkServer RD430 User Guide
