ThinkStation E32 User Guide Machine Types: 30A2 and 30A3
Note: Before using this information and the product it supports, be sure to read and understand the “Important safety information” on page v and Appendix B “Notices” on page 141. First Edition (September 2013) © Copyright Lenovo 2013. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents Important safety information . . . . . . v Service and upgrades . . . . . . Static electricity prevention . . . . Power cords and power adapters . Extension cords and related devices Plugs and outlets. . . . . . . . External devices . . . . . . . . Heat and product ventilation . . . Operating environment . . . . . Modem safety information . . . . Laser compliance statement . . . Power supply statement . . . . . Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the power supply assembly . . Replacing the microprocessor . . . . . . Replacing the cover presence switch . . . Replacing the internal speaker. . . . . . Replacing the front audio and USB assembly . . . . . . . . . . . . . . Replacing the system fan. . . . . . . . Replacing the thermal sensor . . . . . . Replacing the power switch. . . . . . . Replacing the Wi-Fi units . . . . . . . . Installing or removing the rear Wi-Fi antenna Installing or removing the front Wi-Fi antenna . . . . . . . . . .
Lenovo ThinkVantage Tools . . . . . . Lenovo Welcome . . . . . . . . . . Help and Support. . . . . . . . . . Safety and Warranty. . . . . . . . . Lenovo Web site . . . . . . . . . . Lenovo Support Web site. . . . . . . Help and service . . . . . . . . . . . . Using the documentation and diagnostic program . . . . . . . . . . . . . Calling for service. . . . . . . . . . Using other services . . . . . . . . Purchasing additional services . . . . . . . . . . . . . . . . . . 135 135 135 135 135 136 136 . .
iv ThinkStation E32 User Guide
Important safety information CAUTION: Before using this manual, be sure to read and understand all the related safety information for this product. Refer to the information in this section and the safety information in the Safety, Warranty, and Setup Guide that you received with this product. Reading and understanding this safety information reduces the risk of personal injury and damage to your product.
or CRU, do not open the static-protective package containing the part until the instructions direct you to install it. When you handle options or CRUs, or perform any work inside the computer, take the following precautions to avoid static-electricity damage: • Limit your movement. Movement can cause static electricity to build up around you. • Always handle components carefully. Handle adapters, memory modules, and other circuit boards by the edges. Never touch exposed circuitry.
Plugs and outlets If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician. Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement. Do not share an electrical outlet with other home or commercial appliances that draw large amounts of electricity; otherwise, unstable voltage might damage your computer, data, or attached devices.
For your safety and to maintain optimum computer performance, always follow these basic precautions with your desktop computer: • Keep the cover closed whenever the computer is plugged in. • Regularly inspect the outside of the computer for dust accumulation. • Remove dust from vents and any perforations in the bezel. More frequent cleanings might be required for computers in dusty or high-traffic areas. • Do not restrict or block any ventilation openings.
Laser compliance statement CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
x ThinkStation E32 User Guide
Chapter 1. Product overview This chapter provides information about the computer features, specifications, software programs provided by Lenovo, and locations of connectors, components, parts on the system board, and internal drives. Features This section introduces the computer features. The information covers a variety of models.
• Audio line-in connector, audio line-out connector, and microphone connector on the rear panel • Microphone connector and headphone connector on the front panel • Internal speaker Connectivity • 100/1000 Mbps integrated Ethernet controller System management features • Ability to store power-on self-test (POST) hardware test results • Desktop Management Interface (DMI) Desktop Management Interface provides a common path for users to access information about all aspects of a computer, including processor typ
• Windows Management Instrumentation (WMI) Windows Management Instrumentation is a set of extensions to the Windows Driver Model. It provides an operating system interface through which instrumented components provide information and notification. Input/Output (I/O) features • 9-pin serial port (one standard and one optional) • Six Universal Serial Bus (USB) 3.0 connectors (two on the front panel and four on the rear panel) • Two USB 2.
• Support for a padlock • Trusted Platform Module (TPM) For more information, see Chapter 4 “Security” on page 25. Preinstalled software programs Your computer is preinstalled with software programs to help you work more easily and securely. For more information, see “Lenovo programs” on page 5.
Specifications This section lists the physical specifications for your computer. Dimensions Width: 102 mm (4.02 inches) Height: 338 mm (13.31 inches) Depth: 375 mm (14.76 inches) Weight Maximum configuration as shipped: 7.8 kg (17.
Note: If a program icon in the Lenovo ThinkVantage Tools program navigation window is dimmed, it indicates that you need to install the program manually. To install the program manually, double-click the program icon. Then, follow the instructions on the screen. When the installation process completes, the program icon will be activated. Table 1.
• Lenovo QuickSnip • Lenovo Solution Center • Lenovo Support An introduction to Lenovo programs This topic provides a brief introduction to some Lenovo programs. Note: Depending on your computer model, some of the programs might not be available. • Lenovo Companion Through the Lenovo Companion program, you can get the information about the accessories for your computer, view blogs and articles about your computer, and check for other recommended programs.
Locating connectors, controls, and indicators on the front of your computer Figure 1 “Front connector, control, and indicator locations” on page 8 shows the locations of the connectors, controls, and indicators on the front of your computer. Figure 1. Front connector, control, and indicator locations 8 1 Optical drive eject/close button 5 USB 3.0 connector (USB port 2) 2 Power switch 6 Microphone connector 3 Hard disk drive activity indicator 7 Headphone connector 4 Power indicator 8 USB 3.
Locating connectors on the rear of your computer Figure 2 “Rear connector locations” on page 9 shows the locations of the connectors on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer. 5 6 7 5 6 7 8 8 3 4 3 4 Figure 2.
Connector Description DisplayPort connector Used to attach a high-performance monitor, a direct-drive monitor, or other devices that use a DisplayPort connector. Note: The DisplayPort connector is not applicable on some models. If your computer has a graphics card installed, be sure to use a monitor connector on the graphics card. Ethernet connector Used to attach an Ethernet cable for a local area network (LAN). Note: To operate the computer within FCC Class B limits, use a Category 5 Ethernet cable.
Locating components Figure 3 “Component locations” on page 11 shows the locations of the various components in your computer. To remove the computer cover, see “Removing the computer cover” on page 32. Figure 3.
Locating parts on the system board Figure 4 “System board part locations” on page 12 shows the locations of the parts on the system board. Figure 4. System board part locations 1 PS/2 keyboard and mouse connector 16 Power fan connector 2 4-pin power connector 17 Front panel connector (for connecting LED indicators and the power switch) 3 Battery 18 Front USB 3.0 connector (for connecting USB connectors 1 and 2 on the front bezel) 4 Microprocessor 19 Front USB 2.
14 eSATA connector 29 System fan connector 15 SATA connectors 1 to 4 (SATA 3.0 connector) 30 Cover presence switch connector (Intrusion switch connector) Locating internal drives Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and enable your computer to read other types of media. Internal drives are installed in bays.
Machine type and model label The machine type and model label identifies your computer. When you contact Lenovo for help, the machine type and model information helps support technicians to identify your computer and provide faster service. The following is a sample of the machine type and model label. Machine Type: XXXX Model Number: XXX Figure 6.
Chapter 2. Using your computer This chapter provides information on using some of the computer components. Frequently asked questions The following are a few tips that will help you optimize the use of your computer. Can I get my user guide in another language? The user guide is available in various languages on the Lenovo Support Web site at: http://www.lenovo.com/ThinkStationUserGuides Where are my recovery discs? Lenovo provides a program that enables you to create recovery discs.
Using the keyboard Depending on your model, your computer comes with either a standard keyboard or a fingerprint reader keyboard. The Microsoft Windows shortcut keys are provided on both keyboard types.
Using the wheel mouse The wheel mouse has the following controls: 1 Primary mouse button Use this button to select or start a program or menu item. 2 Wheel Use the wheel to control the scrolling action of the mouse. The direction in which you rotate the wheel controls the direction of the scrolling action. 3 Secondary mouse button Use this button to display a menu for the active program, icon, or object.
1. From the Windows desktop, click Start ➙ Control Panel ➙ Appearance and Personalization. 2. In the Taskbar and Start Menu section, click Customize icons on the taskbar. 3. Click Turn system icons on or off and change the volume behaviors from Off to On. 4. Click OK to save the new settings. To add the volume icon to the taskbar on the Windows 8 operating system, do the following: 1. Open Control Panel, and click Appearance and Personalization. 2.
• Do not write or stick paper on the disc. • Do not scratch or mark the disc. • Do not place or store the disc in direct sunlight. • Do not use benzene, thinners, or other cleaners to clean the disc. • Do not drop or bend the disc. • Do not insert damaged discs into the drive. Warped, scratched, or dirty discs can damage the drive. Playing a CD or DVD If your computer comes with a DVD drive, you can listen to audio CDs or watch DVD movies. To play a CD or DVD, do the following: 1.
20 ThinkStation E32 User Guide
Chapter 3. You and your computer This chapter provides information about accessibility, comfort, and relocating your computer to other countries or regions. Accessibility and comfort Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort. Arrange your workplace and the equipment you use to suit your individual needs and the kind of work that you perform. In addition, use healthy work habits to maximize your performance and comfort while using your computer.
Adjust the monitor so the top of the screen is at, or slightly below, eye level. Place the monitor at a comfortable viewing distance, usually 51 to 61 cm (20 to 24 inches), and position it so you can view it without having to twist your body. Also, position other equipment you use regularly, such as the telephone or a mouse, within easy reach. Glare and lighting Position the monitor to minimize glare and reflections from overhead lights, windows, and other light sources.
Registering your computer When you register your computer, information is entered into a database, which enables Lenovo to contact you in case of a recall or other severe problem. After you register your computer with Lenovo, you will receive quicker service when you call Lenovo for help. In addition, some locations offer extended privileges and services to registered users. To register your computer with Lenovo, do one of the following: • Go to http://www.lenovo.
Replacement power cords If you relocate your computer to a country or region that uses an electrical outlet style different from the type you are currently using, you will have to purchase either electrical plug adapters or new power cords. You can order power cords directly from Lenovo. For power cord information and part numbers, go to: http://www.lenovo.
Chapter 4. Security This chapter provides information about how to protect your computer from theft and unauthorized use. Security features The following security features are available on your computer: • Computrace Agent software embedded in firmware The Computrace Agent software is an IT asset management and computer theft recovery solution. The software detects if changes have been made on the computer, such as hardware, software, or the computer call-in location.
Locking the computer cover Locking the computer cover helps prevent unauthorized people from gaining access to the inside of your computer. Your computer comes with a padlock loop so that the computer cover cannot be removed when a padlock is installed. 5 6 7 3 4 Figure 7.
Attaching a Kensington-style cable lock You can use a Kensington-style cable lock to secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to the security-lock slot at the rear of your computer and is operated with a key or combination depending on the type selected. The cable lock also locks the buttons used to open the computer cover. This is the same type of lock used with many notebook computers.
Attaching a cable lock A cable lock can be used to secure devices, such as the keyboard and the mouse, by locking the device cables to your computer. The cable lock attaches to the cable-lock slots on the rear of your computer. See “Locating connectors on the rear of your computer” on page 9. To install a cable lock, do the following: 1. Insert the clip 1 into the cable-lock slot 4 . 2. Pull the cables you want to lock through the dents in the cable lock. 3.
• Hard Disk Password: Setting a Hard Disk Password prevents unauthorized access to the data on the hard disk drive. When a Hard Disk Password is set, you are prompted to type a valid password each time you try to access the hard disk drive. For more information, see “Hard Disk Password” on page 104. • Administrator Password: Setting an Administrator Password deters unauthorized users from changing configuration settings.
Lenovo provides a full version of antivirus software on your computer with a free 30-day subscription. After 30 days, you must renew the license to continue receiving the antivirus software updates. Note: Virus definition files must be kept up-to-date to guard against new viruses. For more information about how to use your antivirus software, refer to the help system of your antivirus software.
Chapter 5. Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for your computer. Handling static-sensitive devices Do not open the static-protective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part. Static electricity, although harmless to you, can seriously damage computer components and parts.
Removing the computer cover Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to remove the computer cover. CAUTION: Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To remove the computer cover, do the following: 1. Remove any media from the drives and turn off all attached devices and the computer. 2.
This section provides instructions on how to remove and reinstall the front bezel. To remove and reinstall the front bezel, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 32. 3.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 93. Accessing the system board components and drives Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to access the system board components and drives. To access the system board components and drives, do the following: 1.
5. Remove any parts that might prevent your access to the memory slots. Depending on your computer model, you might need to remove the PCI Express x16 graphics card for easier access to the memory slots. See “Installing or replacing a PCI card” on page 36. 6. Depending on whether you are installing or replacing a memory module, do one of the following: • If you are replacing an old memory module, open the retaining clips and gently pull the memory module out of the memory slot. Figure 13.
7. Position the new memory module over the memory slot. Make sure that the notch 1 on the memory module aligns correctly with the slot key 2 on the system board. Push the memory module straight down into the slot until the retaining clips close. Figure 15. Installing a memory module 8. Reinstall the PCI Express x16 graphics card if you have removed it. What to do next: • To work with another piece of hardware, go to the appropriate section.
Figure 16. Removing a PCI card Notes: a. The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small amount until it is removed from the card slot. b. If the card is held in place by a retaining latch, disengage the card retaining latch on the PCI card slot. Then grasp the card and gently pull it out of the slot. Figure 17. Disengaging the card retaining latch 5. Remove the new PCI card from its static-protective package. 6.
Figure 18. Installing a PCI card Note: If you are installing a PCI Express x16 graphics card, make sure the memory slot retaining clips are closed before you install the graphics card. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93.
5. Press the release tab 1 as shown and pivot the drive bay assembly upward. Figure 19. Pivoting the drive bay assembly upward 6. Install the new card reader into the card reader bracket. Then install the two screws to secure the card reader to the bracket. 7. Install the card reader bracket to the chassis. Then push the bracket to the left to align the screw hole in the bracket with the corresponding hole in the chassis. Figure 20. Installing the card reader Chapter 5.
8. Install the screw to secure the card reader bracket to the chassis. Figure 21. Installing the screw that secures the card reader 9. Connect the card reader cable to Front USB connectors on the system board. See “Locating parts on the system board” on page 12. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93.
5. Press the release tab 1 as shown and pivot the drive bay assembly upward. Figure 22. Pivoting the drive bay assembly upward 6. Disconnect the card reader cable from the USB connector on the system board. See “Locating parts on the system board” on page 12. 7. Remove the screw that secures the card reader bracket. Then, remove the card reader bracket from the chassis. Figure 23. Removing the screw that secures the card reader 8. Remove the two screws that secure the card reader to its bracket.
10. Install the card reader bracket to the chassis. Then push the bracket to the left to align the screw hole in the bracket with the corresponding hole in the chassis. Figure 24. Installing the card reader 11. Install the screw to secure the card reader bracket to the chassis. Figure 25. Installing the screw that secures the card reader 12. Reconnect the card reader cable to one of the USB connectors on the system board. See “Locating parts on the system board” on page 12.
Replacing the battery Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. Your computer has a special type of memory that maintains the date, time, and settings for built-in features, such as parallel-port assignments (configuration). A battery keeps this information active when you turn off the computer. The battery normally requires no charging or maintenance throughout its life; however, no battery lasts forever.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93. Installing the solid-state drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to install the 2.5-inch solid-state drive. To install the solid-state drive, do the following: 1.
2. To install the solid-state drive with the storage converter into the 3.5-inch hard disk drive bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the storage converter. Figure 29. Installing the solid-state drive with the storage converter into the hard disk drive bracket 3. Connect the signal cable and the power cable to the solid-state drive. 4. Install the solid-state drive into the desired hard disk drive bay.
5. Press the blue retaining clip to pivot the drive bay assembly upward. Figure 30. Pivoting the drive bay assembly upward 6. Insert the mSATA solid-state drive into the mini PCI Express slot on the storage converter, and then press the mSATA solid-state drive downward. Figure 31. Installing the mSATA solid state drive into the storage converter 7. Install the two screws to secure the mSATA solid-state drive to the storage converter. Figure 32.
8. Insert the mSATA solid-state drive storage converter to the chassis and push the converter to the left to align the screw hole in the converter with the corresponding hole in the chassis. Then install the screw to secure the mSATA solid-state drive storage converter to the chassis. Figure 33. Installing the mSATA solid-state drive 9. Connect the signal cable and the power cable to the mSATA solid-state drive. What to do next: • To work with another piece of hardware, go to the appropriate section.
5. Press the blue retaining clip to pivot the drive bay assembly upward. Figure 34. Pivoting the drive bay assembly upward 6. Disconnect the card reader cable from the USB connector on the system board. See “Locating parts on the system board” on page 12. 7. Disconnect the signal cable and power cable from the mSATA solid state drive. 8. Remove the screw that secures the mSATA solid-state drive storage converter. Then remove the mSATA solid-state drive storage converter from the chassis. Figure 35.
9. Remove the two screws that secure the mSATA solid-state drive from the storage converter. Figure 36. Removing the screws that secure the mSATA solid state drive 10. Remove the mSATA solid-state drive from the mini PCI Express slot on the storage converter. Figure 37. Removing the mSATA solid state drive 11. To install a new mSATA solid-state drive, insert the mSATA solid-state drive into the mini PCI Express slot on the storage converter, and then press the mSATA solid-state drive downward.
12. Install the two screws to secure the mSATA solid-state drive to the storage converter. Figure 39. Installing the screws that secure the mSATA solid state drive 13. Insert the mSATA solid-state drive storage converter to the chassis and push the converter to the left to align the screw hole in the converter with the corresponding hole in the chassis. Then install the screw to secure the mSATA solid-state drive storage converter to the chassis. Figure 40. Installing the mSATA solid-state drive 14.
Replacing the hard disk drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to replace the hard disk drive. Note: This section also applies to computer models with a 2.5-inch solid-state drive. To replace the hard disk drive, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover.
6. Pull the blue handle to slide the hard disk drive out of the drive cage. Figure 42. Removing the hard disk drive 7. Flex the sides of the blue bracket to remove the hard disk drive from the bracket. 8. To install a new hard disk drive into the blue bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 43.
9. Slide the new hard disk drive into the drive cage until it snaps into position. Figure 44. Installing the hard disk drive 10. Connect the signal cable and the power cable to the new hard disk drive. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93.
Figure 45. Pivoting the drive bay assembly upward 3 4 5 6 7 8 5. Remove the cable clip on the bottom of the primary hard disk drive bay as shown. Figure 46.
3 4 5 6 7 8 6. Align the four holes in the secondary hard disk drive bracket with the corresponding four tabs on the bottom of the primary hard disk drive bay as shown. Then, position the bracket onto the bottom of the primary hard disk drive bay so that the tabs on the bay pass through the holes in the bracket. Figure 47. Positioning the bracket onto the bottom of the primary hard disk drive bay 3 4 5 6 7 8 7.
3 4 5 6 7 8 8. Install the screw to secure the secondary hard disk drive bracket to the chassis. Figure 49. Installing the screw to secure the secondary hard disk drive bracket 9. To install a new hard disk drive into the blue bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 50.
3 4 5 6 7 8 10. Slide the new secondary hard disk drive into the bracket until it snaps into position. Figure 51. Installing the secondary hard disk drive 11. Connect the signal cable and the power cable to the new secondary hard disk drive. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93.
Figure 52. Pivoting the drive bay assembly upward 5. Locate the secondary hard disk drive bay. See “Locating internal drives” on page 13. 6. Disconnect the signal cable and the power cable from the primary hard disk drive and secondary hard disk drive. 3 4 5 6 7 8 7. Pull the blue handle to slide the secondary hard disk drive from the bracket. Figure 53.
8. To install a new hard disk drive into the blue bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 54. Installing the hard disk drive into the bracket 3 4 5 6 7 8 9. Slide the new secondary hard disk drive into the bracket until it snaps into position. Figure 55. Installing the secondary hard disk drive 10.
Replacing the optical drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to replace the optical drive. To replace the optical drive, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 32. 3. Remove the front bezel.
6. Press the optical drive lock 1 on the right side of the drive bay assembly and slide the optical drive out of the rear of the bay. Figure 57. Removing the optical drive 7. Install the optical drive retainer on the side of the new optical drive. Figure 58. Installing the optical drive retainer Chapter 5.
8. Slide the new optical drive into the drive bay until it snaps into position. Figure 59. Installing the optical drive 9. Connect the signal cable and the power cable to the rear of the optical drive. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93.
4. Follow this sequence to remove the four screws that secure the heat sink and fan assembly to the system board: a. Partially remove screw 1 , then fully remove screw 2 , and then fully remove screw 1 . b. Partially remove screw 3 , then fully remove screw 4 , and then fully remove screw 3 . Note: Carefully remove the four screws from the system board to avoid any possible damage to the system board. The four screws cannot be removed from the heat sink and fan assembly. Figure 60.
7. Place the new heat sink and fan assembly on the system board so that the four screws are aligned with the corresponding holes in the system board. Ensure that you properly place the new heat sink and fan assembly so that you can easily connect the new heat sink and fan assembly cable to the microprocessor fan connector on the system board. 8.
Hazardous moving parts. Keep fingers and other body parts away. CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. To replace the power supply assembly, do the following: 1.
5. Press the release tab 1 as shown and pivot the drive bay assembly upward. Figure 64. Pivoting the drive bay assembly upward 6. Record the cable routing and cable connections. Then, disconnect the power supply assembly cables from all drives and from power connectors 1 , 2 , and 3 on the system board. Figure 65. Power connectors on the system board 7. Release the power supply assembly cables from any cable clips or ties that secure the cables to the chassis.
3 4 5 6 7 8 8. At the rear of the computer, remove the three screws that secure the power supply assembly. Press the power supply clip 1 downward to release the power supply assembly and then slide the power supply assembly to the front of the computer. Lift the power supply assembly out of the computer. Figure 66. Removing the power supply assembly 9. Ensure that the new power supply assembly is the correct replacement. 10.
11. Connect the new power supply assembly cables to all drives and the system board. See “Locating parts on the system board” on page 12. 12. Press the release tab 1 as shown and pivot the drive bay assembly downward until it snaps into position. Figure 68. Pivoting the drive bay assembly downward 13. Position the heat sink fan duct on the top of the heat sink as shown. Then, press the heat sink fan duct straight down until it snaps into position. Figure 69.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93. Replacing the microprocessor Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to replace the microprocessor. CAUTION: The heat sink and microprocessor might be very hot.
6. Lift the microprocessor straight up and out of the microprocessor socket. Figure 71. Removing the microprocessor Notes: a. Your microprocessor and socket might look different from the one illustrated. b. Note the orientation of the microprocessor in the socket. You can either look for the small triangle 1 on one corner of the microprocessor or note the orientation of the notches 2 on the microprocessor. This is important when installing the new microprocessor on the system board. c.
10. Lower the new microprocessor straight down into the microprocessor socket on the system board. Figure 72. Installing the microprocessor 11. Close the microprocessor retainer and lock it into position with the small handle to secure the new microprocessor in the socket. 12. Reinstall the heat sink and fan assembly with the fan duct as shown. See “Replacing the heat sink and fan assembly” on page 62. Figure 73. Reinstalling the heat sink and fan assembly with the fan duct Chapter 5.
13. Reconnect all cables that were disconnected from the system board. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 93. Replacing the cover presence switch Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v.
7. Put the new cover presence switch into the hole and press it down until it snaps into position. Note: Note the orientation of the cover presence switch. Figure 75. Installing the cover presence switch 8. Reconnect the cover presence switch cable to the cover presence switch connector on the system board. See “Locating parts on the system board” on page 12. 9. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 32.
4. Press the release tab 1 as shown and pivot the drive bay assembly upward. Figure 76. Pivoting the drive bay assembly upward 5. Disconnect the internal speaker cable from the system board. 6. Push the tab 1 from inside and slide the internal speaker to the left to remove it from the chassis. Figure 77.
7. Align the new internal speaker with the four metal clips 1 on the inner side of chassis, and then slide the speaker to the right until it snaps into position. Figure 78. Installing the internal speaker 8. Connect the internal speaker cable to the internal speaker connector on the system board. See “Locating parts on the system board” on page 12. What to do next: • To work with another piece of hardware, go to the appropriate section.
4. Press the release tab 1 as shown and pivot the drive bay assembly upward. Figure 79. Pivoting the drive bay assembly upward 5. Disconnect the front audio and USB assembly cables from the system board and note the cables routing. See “Locating parts on the system board” on page 12. 6. Remove the screw that secures the front audio and USB assembly bracket. Then remove the front audio and USB assembly bracket from the chassis. Figure 80. Removing the front audio and USB assembly 7.
11. Reconnect the front USB and front audio cables to the system board. See “Locating parts on the system board” on page 12. 12. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 32. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93.
6. The system fan is attached to the chassis by four rubber mounts. Remove the system fan by cutting the rubber mounts and lifting the system fan out of the chassis. 3 4 5 6 7 8 Note: The new front fan assembly will have four new rubber mounts attached. Figure 82. Removing the system fan 3 4 5 6 7 8 7. Install the new system fan by aligning the new rubber mounts that came with the new system fan with the corresponding holes in the chassis, and then push the rubber mounts through the holes.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 93. Replacing the thermal sensor Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to replace the thermal sensor. To replace the thermal sensor, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover.
9. Pull the entire thermal sensor out of the chassis. 10. Insert the connector and cable of the new thermal sensor into the left hole 1 in the chassis. Then align the two tabs on the plastic holder holding the thermal sensor with the two holes 1 and 2 in the chassis, and press the plastic holder until it snaps into position. Figure 85. Installing the new thermal sensor 11. Reconnect the thermal sensor cable to the system board. See “Locating parts on the system board” on page 12. 12.
3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 32. 4. Locate the power switch. See “Locating components” on page 11. 5. Press the release tab 1 as shown and pivot the drive bay assembly upward. Figure 86. Pivoting the drive bay assembly upward 6. Disconnect the power switch cable from the power switch connector on the system board. See “Locating parts on the system board” on page 12. 7. Push the power switch inward through the hole to disengage it from the chassis.
8. Insert the two plastic tabs in the new power switch through the hole on the chassis, and then press the power switch as shown until it snaps into position. Figure 88. Installing the new power switch 9. Reconnect the power switch cable to the system board. See “Locating parts on the system board” on page 12. 10. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 32. What to do next: • To work with another piece of hardware, go to the appropriate section.
3. If your computer comes with a Wi-Fi card module that supports the Bluetooth function, disconnect the Bluetooth cable from the Wi-Fi adapter card. Figure 89. Disconnecting the Bluetooth cable Note: The Bluetooth cable connects the Bluetooth connector on the Wi-Fi adapter card to the front USB connector on the system board to support the Bluetooth function. 4. Rotate the PCI card retainer to the open position. 5. Grasp the Wi-Fi adapter card that is currently installed and gently pull it out of the slot.
Removing the Wi-Fi card module To remove the Wi-Fi card module, do the following: 1. Remove the Wi-Fi adapter card from the computer, and then disconnect the front and rear Wi-Fi antenna cables from the Wi-Fi card module. Figure 91. Removing the Wi-Fi antenna cables 2. Remove the two screws that secure the Wi-Fi card module to the Wi-Fi adapter card. Figure 92.
3. Pull the Wi-Fi card module out of the mini PCI Express slot to remove it from the Wi-Fi adapter card. Figure 93. Removing the Wi-Fi card module Installing the Wi-Fi units To install the Wi-Fi units, do the following: Chapter 5.
1. Insert the Wi-Fi card module into the mini PCI Express slot, and then install the two screws to secure the Wi-Fi card module to the Wi-Fi adapter card. Figure 94.
2. Connect the front antenna cable and rear antenna cable to the Wi-Fi card module. Figure 95. Installing the Wi-Fi antenna cables 3. Install the Wi-Fi adapter card into the PCI Express x1 slot on the system board. See “Locating parts on the system board” on page 12. 4. If the installed Wi-Fi card module supports the Bluetooth function, use a Bluetooth cable to connect the Bluetooth connector on the Wi-Fi adapter card to the front USB connector on the system board. 5.
Installing or removing the rear Wi-Fi antenna Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to install or remove the rear Wi-Fi antenna. Installing the rear Wi-Fi antenna To install the rear Wi-Fi antenna, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2.
3 4 5 6 7 8 3. Hold the thicker end of the rear Wi-Fi antenna and unscrew the Wi-Fi antenna from the rear of the computer. Figure 98. Removing the rear Wi-Fi antenna What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93.
4. Press the release tab 1 as shown and pivot the drive bay assembly upward. Figure 99. Pivoting the drive bay assembly upward 5. Peel off the paper that protects the sticker on the front antenna. Figure 100. Peeling off the paper that protects the sticker 6. Stick the front antenna to the front panel as shown. Then insert the front antenna cable through the hole in the front panel.
Figure 101. Installing the front Wi-Fi antenna 7. Connect the front antenna cable to the Wi-Fi card module. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93. Removing the front Wi-Fi antenna To remove the front Wi-Fi antenna, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover.
5. Disconnect the front antenna cable from the Wi-Fi card module. 6. Remove the front antenna and cable from the front of the computer. Figure 103. Removing the front Wi-Fi antenna What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 93. Completing the parts replacement After completing the installation or replacement for all parts, you need to reinstall the computer cover and reconnect cables. Depending on the parts you installed or replaced, you might need to confirm the updated information in the Setup Utility program.
3 4 5 6 7 8 5. Position the computer cover on the chassis so that the rail guides on the bottom of the computer cover engage the rails on the chassis. Then, push the cover to the front of the computer until it snaps into position. Figure 106. Reinstalling the computer cover 6. Install the screws to secure the computer cover. 7. If there is a padlock available, lock the computer cover. See “Locking the computer cover” on page 26. 8.
Chapter 6. Recovery information This chapter provides information about the recovery solutions provided by Lenovo.
Creating recovery media This section provides instructions on how to create recovery media. Note: On the Windows 7 operating system, you can create recovery media using discs or external USB storage devices. To create recovery media on the Windows 7 operating system, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Factory Recovery Disks. Then, follow the instructions on the screen. Using recovery media This section provides instructions on how to use recovery media.
1. From the Windows desktop, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Enhanced Backup and Restore. The Rescue and Recovery program opens. 2. In the Rescue and Recovery main window, click the Launch advanced Rescue and Recovery arrow. 3. Click Back up your hard drive and select backup operation options. Then, follow the instructions on the screen to complete the backup operation.
2. Turn on your computer. When you see the logo screen, press Enter, and then press F11 to enter the Rescue and Recovery workspace. 3. If you have set a Rescue and Recovery password, type your password when prompted. The Rescue and Recovery workspace opens after a short delay. Note: If the Rescue and Recovery workspace fails to open, see “Solving recovery problems” on page 100. 4.
1. Attach the USB hard disk drive to one of the USB connectors on your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Please select boot device window opens, release the F12 key. 3. In the Please select boot device window, select the USB hard disk drive as the first boot device and press Enter. The rescue medium starts. When the rescue medium starts, the Rescue and Recovery workspace opens.
Note: If you need updated device drivers, see “Getting the latest device drivers for your computer” on page 113 for more information. Reinstalling software programs If a software program you installed on your computer is not working correctly, you might need to remove and reinstall it. Reinstalling overwrites the existing programs files and usually fixes any problems that you might have had with that program. To remove a program in your system, see Microsoft Windows help system for detailed information.
It is important to create a rescue medium and a set of recovery media as early as possible and store them in a safe place for future use. Recovery information for the Windows 8 operating system This section provides information about the recovery solutions provided on computers preinstalled with the Windows 8 operating system.
102 ThinkStation E32 User Guide
Chapter 7. Using the Setup Utility program The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1. Make sure your computer is turned off. 2. Repeatedly press and release the F1 key when turning on the computer.
• Administrator Password • Hard Disk Password You do not have to set any passwords to use your computer. However, using passwords improves computing security. If you decide to set any passwords, read the following sections. Password considerations A password can be any combination of up to 64 alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised.
2. From the Setup Utility program main menu, select Security. 3. Depending on the password type, select Set Power-On Password, Set Administrator Password, or Hard Disk Password. 4. Follow the instructions on the right side of the screen to set, change, or delete a password. Note: A password can be any combination of up to 64 alphabetic and numeric characters. For more information, see “Password considerations” on page 104.
Selecting a startup device If your computer does not start up from a device such as the disc or hard disk drive as expected, do one of the following to select the startup device you want. Selecting a temporary startup device Use this procedure to select a temporary startup device. Note: Not all discs and hard disk drives are bootable. 1. Turn off your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Please select boot device window displays, release the F12 key.
1. Start the Setup Utility program. 2. From the Setup Utility program main menu, select Power ➙ Automatic Power On, and press Enter. 3. Select Wake Up on Alarm and press Enter. Then follow the instructions on the screen. 4. Press F10 to save changes and exit the Setup Utility program. Press Enter when prompted to confirm the exit. • Enabling the after power loss feature The after power loss feature enables your computer to wake up when the power supply resumes after a sudden loss of electricity.
2. From the Setup Utility program main menu, select Power. 3. Select Intelligent Cooling Engine (ICE). The Intelligent Cooling Engine (ICE) window is displayed. 4. Select ICE Thermal Alert. The ICE Thermal Alert window is displayed. 5. Select Enabled or Disabled as desired. 6. Press F10 to save changes and exit the Setup Utility program. See “Exiting the Setup Utility program” on page 108.
Chapter 8. Configuring RAID This chapter provides information about how to configure Redundant Array of Independent Disks (RAID) for your computer. Note: The information about configuring RAID in this chapter is applicable only for a Windows environment. For information about configuring RAID in a Linux environment, contact your Linux software provider.
8. When prompted, press Y to accept the warning message and create the volume. 9. Return to step 2 to create additional RAID volumes, or select Exit and press Enter. 10. Press Y when prompted to confirm the exit. Deleting RAID volumes This section describes how to use the Intel Matrix Storage Manager option ROM configuration utility to delete RAID volumes. To delete RAID volumes, do the following: 1.
Chapter 9. Updating system programs This chapter provides information about updating the POST and BIOS, and how to recover from a POST and BIOS update failure. Using system programs System programs are the basic layer of software built into your computer. System programs include the POST, the BIOS, and the Setup Utility program. The POST is a set of tests and procedures that are performed each time you turn on your computer.
Updating (flashing) the BIOS from your operating system Note: Because Lenovo makes constant improvements to its Web sites, the Web page contents are subject to change without notice, including the contents referenced in the following procedure. To update (flash) the BIOS from your operating system, do the following: 1. Go to http://www.lenovo.com/support. 2. Click Download Drivers & Software. 3. Click Use Quick Path. 4.
Chapter 10. Preventing problems This chapter provides information that can help you avoid common problems and keep your computer running smoothly. Keeping your computer current In some situations you may find it necessary to have the most current software programs, device drivers, or operating system. This section explains how to get the latest updates for your computer.
Using System Update The System Update program helps you keep the software on your computer up-to-date. Update packages are stored on Lenovo servers and can be downloaded from the Lenovo Support Web site. Update packages can contain applications, device drivers, BIOS flashes, or software updates.
Cleaning your computer It is a good practice to clean your computer periodically to protect the surfaces and ensure trouble-free operation. CAUTION: Be sure to turn off the computer and monitor power switches before cleaning the computer and monitor screen. Computer Use only mild cleaning solutions and a damp cloth to clean the painted surfaces of the computer. Keyboard To clean your computer keyboard, do the following: 1. Apply some isopropyl rubbing alcohol to a soft, dust-free cloth. 2.
Many computer supply stores carry the special cleaning fluids for displays. Use cleaning fluids developed for LCD displays only. First apply the fluid to a lint-free, soft cloth, then clean the LCD display. Some computer supply stores carry pre-moistened towelettes for LCD maintenance. Cleaning a glass-screen surface To clean a glass-screen surface, wipe it gently with a soft, dry cloth, or blow on the screen to remove grit and other loose particles.
Chapter 11. Troubleshooting and diagnostics This chapter provides information about diagnosing and troubleshooting computer problems. If your computer problem is not described here, see Chapter 12 “Getting information, help, and service” on page 135 for additional troubleshooting resources. Basic troubleshooting The following table provides information to help you troubleshoot your computer problems. Note: If you cannot correct the problem, have the computer serviced.
Symptom Action The operating system does not start. Verify that: The computer beeps multiple times before the operating system starts. Verify that no keys are stuck. • The startup sequence includes the device where the operating system resides. Usually, the operating system is on the hard disk drive. For more information, see “Selecting a startup device” on page 106.
1. Remove the new hardware option or software. If you must remove the computer cover to remove a hardware option, make sure you review and follow the electrical safety information provided with your computer. For your safety, do not operate the computer with the cover removed. 2. Run the diagnostic program to ensure your computer is operating correctly. 3. Reinstall the new hardware option or software following the manufacturer's instructions.
Note: When external-speaker or headphone cables are attached to the audio connector, the internal speaker, if present, is disabled. In most cases, if an audio adapter is installed in one of the expansion slots, the audio function built into the system board is disabled; use the audio jacks on the adapter. • Make sure that the program you are running is designed for use in the Microsoft Windows operating system.
An audio disc or AutoPlay-enabled disc does not automatically play when it is inserted into a CD drive Symptom: An audio disc or AutoPlay-enabled disc does not automatically play when it is inserted into a CD drive. Actions: • If you have multiple CD or DVD drives installed (or a combination of CD and DVD drives), try inserting the disc into the other drive. In some cases, only one of the drives is connected to the audio subsystem.
Actions: • Restart the DVD player program. • Close any open files, turn off the computer, and then restart the computer. • Try a lower screen resolution or color depth. If these actions do not correct the problem, run the Lenovo Solution Center program. If you need technical assistance, see Chapter 12 “Getting information, help, and service” on page 135. DVD movie will not play Symptom: DVD movie will not play. Actions: • Make sure that the disc surface is clean and not scratched.
• On computers that have a CD-ROM or CD-RW drive in addition to a DVD-ROM drive, make sure that the DVD disc is in the drive labeled “DVD”. If these actions do not correct the problem, run the Lenovo Solution Center program. If you need technical assistance, see Chapter 12 “Getting information, help, and service” on page 135. Intermittent problems Symptom: A problem occurs only occasionally and is difficult to repeat.
3. Click Devices and Printers. 4. Double-click USB Enhanced Performance Keyboard. The USB Enhanced Performance Keyboard Customization program starts. If these actions do not correct the problem, have the computer and keyboard serviced. See Chapter 12 “Getting information, help, and service” on page 135 for details. The mouse or pointing device does not work Symptom: The mouse or pointing device does not work.
Action: If the Transceiver Communications LED is not on, reconnect the transceiver and the keyboard. Monitor problems Note: Many monitors have status-indicator lights and built-in controls for adjusting brightness, contrast, width, height, and other picture adjustments. However, the controls vary from monitor type to monitor type. For information about the status lights and using the controls, refer to the documentation that comes with your monitor.
Actions: • The monitor might be operating in a low-refresh rate display mode. Set the monitor to the highest, noninterlaced refresh rate supported by your monitor and the video controller in your computer. Attention: Using a resolution or refresh rate that is not supported by your monitor might damage it. Check the documentation that comes with your monitor to verify the supported refresh rates. • The monitor might be affected by interference from nearby equipment.
Ethernet problems For Ethernet problems, select your symptom from the following list: • “Your computer cannot connect to the network” on page 127 • “The adapter stops working for no apparent reason” on page 127 • “If your computer is a Gigabit Ethernet model and you use a speed of 1000 Mbps, the connection fails or errors occur” on page 128 • “If your computer is a Gigabit Ethernet model, it cannot connect to the network at 1000 Mbps.
Action: The network driver files may be corrupt or missing. Update the driver by referring to the “Solution” description for the procedure to make sure that the correct device driver is installed. The Wake on LAN feature is not working Symptom: The Wake on LAN (WOL) feature is not working. Actions: • Make sure that WOL is enabled in the BIOS Setup Utility program. • If it is, check with your LAN administrator for the necessary settings.
Bluetooth problem Symptom: Sound does not come from the Bluetooth headset or headphone but comes from the local speaker even though the headset or headphone is connected using the Headset profile or AV profile. Action: Do the following: 1. Exit the application that uses the sound device (for example, Windows Media Player). 2. Open Control Panel. 3. Click Hardware and Sound ➙ Sound. 4. Select the Playback tab. 5.
– All external SCSI options are turned on. External SCSI options must be turned on before the computer is turned on. For more information, see your SCSI documentation. • Verify that the option and any required device drivers are installed correctly. If these actions do not correct the problem, run the Lenovo Solution Center program. If you need technical assistance, see Chapter 12 “Getting information, help, and service” on page 135.
4. Click Clean up system files. 5. Click the More Options tab. 6. In the Programs and Features area, click the Clean up button. 7. A list of installed programs is displayed. Select the program that you want to remove. Click Uninstall/Change. • Clean out your Inbox, Sent Items, and Deleted Items folders from your e-mail application. The folder names and procedures vary depending on your e-mail application. If you need assistance, see the help system for your e-mail application.
Actions: Verify that: 1. The printer is turned on and is online. 2. Paper is loaded correctly. 3. The printer signal cable is securely connected to the correct parallel, serial, or USB connector on the computer. Note: Non-IEEE-approved printer signal cables might cause unpredictable problems. 1. Any device drivers and other software that came with the printer are correctly installed. 2. You have assigned the printer port correctly in your operating system, application program, or BIOS settings.
Actions: • Most software programs have built-in help systems that provide instructions for most tasks. If you are having difficulty performing a specific task within a software program, refer to the help system for that program. Help systems are typically accessible from a menu or button in the program, and frequently from the F1 key. • If you are having difficulty with the Windows operating system or one of its components, refer to the Windows help system. It is accessible from the Windows Start menu.
Lenovo Solution Center The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems. It combines diagnostic tests, system information collection, security status, and support information, along with hints and tips for maximum system performance. Notes: • The Lenovo Solution Center program can be downloaded from http://www.lenovo.com/diags. • If you are using other Windows operating system rather than Windows 7 and Windows 8, go to http://www.lenovo.
Chapter 12. Getting information, help, and service This chapter contains information about help, service, and technical assistance for products manufactured by Lenovo. Information resources You can use the information in this section to access useful resources relating to your computing needs. Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely.
• Access troubleshooting and support information for your computer model and other supported products. • Find the service and support phone numbers for your country or region. • Find a Service Provider located near you. Lenovo Support Web site Technical support information is available on the Lenovo Support Web site at: http://www.lenovo.
• • • • • • Replacement or use of parts not manufactured for or by Lenovo or non-warranted Lenovo parts Identification of software problem sources Configuration of BIOS as part of an installation or upgrade Changes, modifications, or upgrades to device drivers Installation and maintenance of network operating systems (NOS) Installation and maintenance of application programs Refer to the Safety, Warranty, and Setup Guide that comes with your computer for information about your warranty type and duration.
138 ThinkStation E32 User Guide
Appendix A. System memory speed The Intel Xeon® microprocessor families compatible with this ThinkStation computer feature an integrated memory controller, which provides the microprocessor with direct access to the system memory. Because of this design, the system memory speed will be determined by a number of factors, including the microprocessor model and the type, speed, size (capacity), and number of DIMMs installed.
140 ThinkStation E32 User Guide
Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo The Lenovo logo Rescue and Recovery ThinkStation ThinkVantage Microsoft and Windows are trademarks of the Microsoft group of companies. Intel, Intel Core, Pentium, and Xeon are trademarks of Intel Corporation in the United States, other countries, or both. Linux is a registered trademark of Linus Torvalds. Other company, product, or service names may be trademarks or service marks of others.
Appendix C. Regulatory information Export classification notice This product is subject to the United States Export Administration Regulations (EAR) and has an Export Classification Control Number (ECCN) of 4A994.b. It can be re-exported except to any of the embargoed countries in the EAR E1 country list. Electronic emissions notices The following information refers to Lenovo personal computer machine types 30A2 and 30A3.
This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the installation of option cards from other manufacturers.
Japan VCCI Class B compliance statement Japan compliance statement for products which connect to the power mains with rated current less than or equal to 20 A per phase Lenovo product service information for Taiwan Keyboard and mouse compliance statement for Taiwan Eurasian compliance mark Additional regulatory information For additional regulatory information, refer to the Regulatory Notice shipped with your computer.
146 ThinkStation E32 User Guide
Appendix D. WEEE and recycling statements Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. For information on recycling Lenovo products, go to: http://www.lenovo.
Some Lenovo computer products sold in Japan may have components that contain heavy metals or other environmental sensitive substances. To properly dispose of disused components, such as a printed circuit board or drive, use the methods described above for collecting and recycling a disused computer or monitor.
Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union. This label is applied to various batteries to indicate that the battery is not to be thrown away, but rather reclaimed upon end of life per this Directive.
150 ThinkStation E32 User Guide
Appendix E. Restriction of Hazardous Substances Directive (RoHS) European Union RoHS Lenovo products sold in the European Union, on or after 3 January 2013 meet the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (“RoHS recast” or “RoHS 2”). For more information about Lenovo progress on RoHS, go to: http://www.lenovo.com/social_responsibility/us/en/RoHS_Communication.
Ukraine RoHS India RoHS RoHS compliant as per E-Waste (Management & Handling) Rules, 2011.
Appendix F. ENERGY STAR model information ENERGY STAR® is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy aimed at saving money and protecting the environment through energy efficient products and practices. Lenovo is proud to offer our customers products with an ENERGY STAR compliant designation.
154 ThinkStation E32 User Guide
Index A a rescue medium, creating and using 98 accessing system board components and drives 34 Administrator, password 104 audio line-in connector 9 audio line-out connector 9 audio subsystem 1 B backup and recovery operations basic troubleshooting 117 battery, replacing 43 boot-block recovery 112 96 C cable lock, security 27–28 card reader, installing 38 card reader, replacing 40 changing password 104 startup device sequence 106 cleaning an optical mouse 115 CMOS, clearing 105 components, internal 11 co
warranty 135 Input/Output (I/O) features 3 installing mSATA solid-state drive 45 solid-state drive 44 installing options memory module 34 PCI card 36 installing or replacing secondary hard disk drive 53 internal drives 1 internal speaker, replacing 73 passwords erasing 105 lost or forgotten 105 passwords, using 103 PCI card 36 installing, replacing 36 slots 36 physical specifications 5 power features 3 power supply assembly, replacing 64 power switch, replacing 80 power-on self-test (POST) 111 Power-On, Pa
getting 135 services other 137 purchasing additional 137 setting password 104 settings changing 103 viewing 103 Setup Utility 103 Setup Utility program, starting 103 Setup Utility, exiting 108 software recovering 95 solid-state drive, installing 44 solving recovery problems 100 starting the Setup Utility program 103 startup device 106 sequence, changing 106 temporary, selecting 106 static-sensitive devices, handling 31 system management 2 programs 111 system board connectors 12 locating parts 12 locations 1
158 ThinkStation E32 User Guide
