ThinkCentre User Guide Machine Types 6008, 6010, 6019, 6062, 6064, 6065, 6066, 6067, 6068, 6069, 6071, 6072, 6073, 6074, 6075, 6076, 6077, 6078, 6079, 6081, 6082, 6086, 6087, 6088, 6089, 7103, 9011, 9012, 9013, 9014, 9018, 9019, 9071, 9087, 9088, 9089, 9096, 9160, 9162, 9163, 9164, 9172, 9174, 9181, 9182, 9193, 9194, 9196, 9303, 9304, 9323, 9325, 9326, 9330, 9967, 9970, 9978, 9979
ThinkCentre User Guide
Note Before using this information and the product it supports, be sure to read the Safety and Warranty Guide that came with this product and Appendix B, “Notices,” on page 67. Second Edition (January 2009) © Copyright Lenovo 2007, 2009. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.
Contents Introduction . . . . . . . . . . . . . v Chapter 1. Important safety information 1 Chapter 2. Arranging your workspace . . 3 Comfort . . . . . . . . . Glare and lighting . . . . . Air circulation . . . . . . . Electrical outlets and cable lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 4 4 Chapter 3. Setting up your computer . . 5 Connecting your computer . . . . . . . . Turning on computer power . . . . . . . . Finishing the software installation . . . . . .
Basic AT commands . . . . . Extended AT commands . . . . MNP/V.42/V.42bis/V.44 commands Fax Class 1 commands . . . . Fax Class 2 commands . . . . Voice commands. . . . . . . iv User Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 61 62 63 63 64 Appendix B. Notices . . . . . . . . . 67 Television output notice . Trademarks . . . . . . . . . . . . . . . . . . . . . . 68 . 68 Index . . . . . . . . . . . . . . .
Introduction This User Guide contains the following information: v Chapter 1, “Important safety information,” on page 1 provides information about where to find safety information for this product. v Chapter 2, “Arranging your workspace,” on page 3 provides information about setting up your computer for comfort and the impact of light sources, air circulation, and electrical outlets.
vi User Guide
Chapter 1. Important safety information CAUTION: Before using this manual, it is important that you read and understand all the related safety information for this product. Refer to the Safety and Warranty Guide that you received with this product for the latest safety information. Reading and understanding this safety information reduces the risk of personal injury and or damage to your product.
2 User Guide
Chapter 2. Arranging your workspace To get the most from your computer, arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Your comfort is of foremost importance, but light sources, air circulation, and the location of electrical outlets can also affect the way you arrange your workspace. Comfort Although no single working position is ideal for everyone, here are a few guidelines to help you find a position that suits you best.
Where it is impossible to avoid reflections or to adjust the lighting, an antiglare filter placed over the screen might be helpful. However, these filters might affect the clarity of the image on the screen; try them only after you have exhausted other methods of reducing glare. Dust buildup compounds problems associated with glare. Remember to clean your monitor screen periodically using a soft cloth moistened with a nonabrasive liquid glass cleaner. Air circulation Your computer and monitor produce heat.
Chapter 3. Setting up your computer Read and understand the Safety and Warranty Guide before you set up your computer. Reading and understanding the safety information reduces the risk of personal injury and or damage to your product. Set up your computer in the best possible work area that suits your needs and habits. For more information, see Chapter 2, “Arranging your workspace,” on page 3. Connecting your computer Use the following information when connecting your computer.
2. Connect the keyboard cable to the appropriate keyboard connector, either the standard keyboard connector 1 or the Universal Serial Bus (USB) connector 2 . Note: Some models will have keyboards with a fingerprint reader. After you setup and turn on your computer, refer to the Access Help online help system for information about your fingerprint reader. See “Access Help” on page 56 for instructions on how to open the online help system. 3. Connect the USB mouse cable to the USB connector. 4.
v If you have a digital video interface (DVI) monitor, your computer must have an adapter installed that supports the DVI monitor. Connect the cable to the connector as shown. 5. If you have a modem, connect the modem using the following information. E ON PH E ON PH E ON PH LINE PH E LIN ON E LIN LIN 1 2 3 E E This illustration shows the two connections on the back of the computer that are needed to set up your modem.
1 Audio line-in 2 Audio line-out 3 Microphone 4 Headphone This connector receives audio signals from an external audio device, such as a stereo system. This connector sends audio signals from the computer to external devices, such as powered stereo speakers. Use this connector to attach a microphone to your computer when you want to record sound or if you use speech-recognition software.
9. Connect any additional devices that you have. Your computer might not have all connectors that are shown. 1394 1394 1 USB 2 Serial 3 S-video 4 Parallel 5 Ethernet 6 MIDI/joystick 7 IEEE 1394 8 eSATA Use this connector to attach a device that requires a USB connection, such as a keyboard, mouse, scanner, printer, or personal digital assistant (PDA). Use this connector to attach an external modem, serial printer, or other device that uses a 9-pin serial connector.
Note: For more information about connectors, refer to the Access Help online help system. See “Access Help” on page 56 for instructions on how to open the online help system. Turning on computer power Turn on the monitor and other external devices first, and then turn on the computer. When the power-on self-test (POST) is finished, the logo window closes. If your computer has preinstalled software, the software installation program starts.
v Record your computer machine type, model, and serial number. If you need service or technical support, you will probably be asked for this information. For further information, refer to the safety and warranty information that is provided with your computer. Updating your operating system Microsoft makes updates available for various operating systems through the Microsoft Windows Update Web site.
Features for machine types: 6008, 6068, 6074, 6079, 6082, 9012, 9018, 9087, 9096, 9163, 9172, 9193 This section provides an overview of the computer features and preinstalled software. System information The following information covers a variety of models. For information for your specific model, use the Setup Utility. See Chapter 5, “Using the Setup Utility,” on page 31.
v Wake on Ring (in the Setup Utility program, this feature is called Serial Port Ring Detect for an external modem) v Remote Administration v Automatic power-on startup v System Management (SM) BIOS and SM software v Ability to store power-on self-test (POST) hardware test results Input/output features v 25-pin Extended Capabilities Port (ECP)/Extended Parallel Port (EPP) v 9-pin serial connector v Eight USB connectors (two on front panel and six on rear panel) v Standard mouse connector v Standard keyboard
Expansion v Three drive bays v Two 32-bit PCI adapter connector v One PCI Express x1 adapter connector Power v 280 Watt power supply with autosensing voltage switching v Automatic 50/60 Hz input frequency switching v Advanced Configuration and Power Interface (ACPI) support Security features v User and administrator passwords for BIOS access v Support for the addition of an integrated cable lock (Kensington lock) v Keyboard with fingerprint reader (some models, see the ThinkVantage Productivity Center progr
Features for machine types: 6010, 6069, 6075, 6081, 6086, 9013, 9019, 9088, 9160, 9164, 9174, 9194, 9304, 9323, 9326, 9978, 9979 This section provides an overview of the computer features and preinstalled software. System information The following information covers a variety of models. For information for your specific model, use the Setup Utility. See Chapter 5, “Using the Setup Utility,” on page 31.
v Wake on Ring (in the Setup Utility program, this feature is called Serial Port Ring Detect for an external modem) v Remote Administration v Automatic power-on startup v System Management (SM) BIOS and SM software v Ability to store power-on self-test (POST) hardware test results Input/output features v 25-pin Extended Capabilities Port (ECP)/Extended Parallel Port (EPP) v 9-pin serial connector v Eight USB connectors (two on front panel and six on rear panel) v Stasndard mouse connector v Standard keyboar
Expansion v Five drive bays v Two 32-bit PCI adapter connector v One PCI Express x1 adapter connector Power v 280 Watt power supply with manual voltage selection switch v Automatic 50/60 Hz input frequency switching v Advanced Configuration and Power Interface (ACPI) support Security features v User and administrator passwords for BIOS access v Support for the addition of an integrated cable lock (Kensington lock) v Keyboard with fingerprint reader (some models, see the ThinkVantage Productivity Center prog
Features for machine types: 6019, 6064, 6066, 6067, 6072, 6073, 6077, 6078, 6087, 6088, 9181, 9196, 9325, 9330, 9967, 9970 This section provides an overview of the computer features and preinstalled software. System information The following information covers a variety of models. For information for your specific model, use the Setup Utility. See Chapter 5, “Using the Setup Utility,” on page 31.
v Wake on Ring (in the Setup Utility program, this feature is called Serial Port Ring Detect for an external modem) v Remote Administration v Automatic power-on startup v System Management (SM) BIOS and SM software v Ability to store power-on self-test (POST) hardware test results Input/output features v 25-pin Extended Capabilities Port (ECP)/Extended Parallel Port (EPP) v 9-pin serial connector v Eight USB connectors (two on front panel and six on rear panel) v Ethernet connector v VGA monitor connector v
Expansion v Three drive bays v One 32-bit PCI adapter connector Power v 280 Watt power supply with autosensing voltage switching v Automatic 50/60 Hz input frequency switching v Advanced Configuration and Power Interface (ACPI) support Security features v User and administrator passwords for BIOS access v Support for the addition of an integrated cable lock (Kensington lock) v Keyboard with fingerprint reader (some models, see the ThinkVantage Productivity Center program for more information) v Cover presen
Features for machine types: 6062, 6065, 6071, 6076, 6089, 7103, 9011, 9014, 9071, 9089, 9162, 9182, 9303 This section provides an overview of the computer features and preinstalled software. System information The following information covers a variety of models. For information for your specific model, use the Setup Utility. See Chapter 5, “Using the Setup Utility,” on page 31.
v Automatic power-on startup v System Management (SM) BIOS and SM software v Ability to store power-on self-test (POST) hardware test results Input/output features v 25-pin Extended Capabilities Port (ECP)/Extended Parallel Port (EPP) v 9-pin serial connector v Eight USB connectors (two on front panel and six on rear panel) v v v v v 22 User Guide Ethernet connector VGA monitor connector Two audio connectors (line-in and line-out) on rear panel Two audio connectors (microphone and headphone) on front pan
Expansion v Two drive bays v One 32-bit PCI adapter connector Power v 225 Watt power supply with autosensing voltage switching v Automatic 50/60 Hz input frequency switching v Advanced Configuration and Power Interface (ACPI) support Security features v User and administrator passwords for BIOS access v Support for the addition of an integrated cable lock (Kensington lock) v Keyboard with fingerprint reader (some models, see the ThinkVantage Productivity Center program for more information) v Cover presence
Specifications for machine types: 6008, 6068, 6074, 6079, 6082, 9012, 9018, 9087, 9096, 9163, 9172, 9193 This section lists the physical specifications for your computer. Dimensions Width: 325 mm (12.8 in.) Height: 107 mm (4.21in.) Depth: 410 mm (16.14 in.) Weight Minimum configuration as shipped: 8.2 kg (18 lbs) Maximum configuration: 10.4 kg (23 lbs) Environment Air temperature: Operating at 0 - 3000 ft (914.
Specifications for machine types: 6010, 6069, 6075, 6081, 6086, 9013, 9019, 9088, 9160, 9164, 9174, 9194, 9304, 9323, 9326, 9978, 9979 This section lists the physical specifications for your computer. Dimensions Width: 400 mm (15.7 in.) Height: 175 mm (6.9 in.) Depth: 432 mm (17.0in.) Weight Minimum configuration as shipped: 8.17 kg (18 lbs) Maximum configuration: 10.21 kg (22.5lbs) Environment Air temperature: Operating at 0 - 3000 ft (914.
Specifications for machine types: 6019, 6064, 6066, 6067, 6072, 6073, 6077, 6078, 6087, 6088, 9181, 9196, 9325, 9330, 9967, 9970 This section lists the physical specifications for your computer. Dimensions Width: 317 mm (12.48 in.) Height: 99 mm (3.9 in.) Depth: 341 mm (13.4in.) Weight Minimum configuration as shipped: 6.32 kg (13.9 lbs) Maximum configuration: 7.42 kg (16.4 lbs) Environment Air temperature: Operating at 0 - 3000 ft (914.
Specifications for machine types: 6062, 6065, 6071, 6076, 6089, 7103, 9011, 9014, 9071, 9089, 9162, 9182, 9303 This section lists the physical specifications for your computer. Dimensions Width: 89 mm (3.5in.) Height: 276 mm (10.9 in.) Depth: 273 mm (10.7 in.) Weight Minimum configuration as shipped: 6.3 kg (13.4 lbs) Maximum configuration: 6.4 kg (14.1 lbs) Environment Air temperature: Operating at 0 - 3000 ft (914.
28 User Guide
Chapter 4. Software overview The computer is manufactured with a preloaded operating system and several preloaded applications. The operating systems available are: v Windows Vista v Windows XP Software provided with your Windows operating system This section describes the Windows applications included with this product. Software provided by Lenovo The following software applications are provided by Lenovo to help you improve productivity and reduce the cost associated with maintaining your computer.
secure access to your computer system. A fingerprint reader keyboard is only available with select computers or can be purchased for computers that support this option. PC Doctor for WINPE, PC Doctor for Windows This diagnostic program is preinstalled from the factory on your hard disk drive. PC-Doctor for Windows works through the Windows operating system to diagnose hardware problems and report operating-system-controlled settings that can cause hardware failures.
Chapter 5. Using the Setup Utility The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating-system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer. 2.
v v v v v v v Contain at least one alphabetic character, one numeric character, and one symbol Contain at least one of the following symbols: , .
3. Select Security Profile by Device. 4. Select the desired devices and settings and press Enter. 5. Return to the Setup Utility program menu and select Exit and then Save Settings or Save and exit the Setup Utility. Note: If you do not want to save the settings, select Exit the Setup Utility without saving. Selecting a startup device If your computer does not start up from a device such as the CD-ROM, diskette, or hard disk drive as expected, use one of the following procedures to select a startup device.
Advanced settings On some computer models, the Advanced settings menu includes a setting to Enable/Disable HyperThreading. This feature works only with HyperThreading-aware operating systems, such as Microsoft Windows XP. The default setting for HyperThreading is Enabled. However, if you select Set Defaults and are using an operating system other than Windows XP, your computer performance might be degraded.
Chapter 6. Updating system programs This chapter contains information about updating POST/BIOS and how to recover from a POST/BIOS update failure. Using system programs System programs are the basic layer of software built into your computer. They include the power-on self-test (POST), the basic input/output system (BIOS) code, and the Setup Utility program. POST is a set of tests and procedures that are performed each time you turn on your computer.
7. Type in the seven character machine type/model of your computer and then press Enter. 8. Follow the instructions on the screen to complete the update. Updating (flashing) BIOS from your operating system Note: Due to the constant improvements made to the Web site, Web page content (including the links referenced in the following procedure) is subject to change. 1. From your browser, type http://www.lenovo.com/support in the address field and press Enter. 2.
12. Replace the Clear CMOS/Recovery jumper to the standard position (pin 1 and pin 2). 13. Remove the BIOS flash diskette from the diskette drive. 14. Close the computer cover and reconnect the power cords for the computer and monitor to electrical outlets. 15. Turn on the computer to restart the operating system. Chapter 6.
38 User Guide
Chapter 7. Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs. If your computer problem is not described here, see Chapter 9, “Getting information, help, and service,” on page 55 for additional troubleshooting resources. Basic troubleshooting The following table provides information to help you troubleshoot your computer problem. Symptom Action The computer does not start when you press the power button.
Symptom Action The USB Keyboard does not work. Verify that: v The computer is turned on. v The keyboard is securely connected to a USB connector on the front or rear of the computer. v No keys are stuck. If you cannot correct the problem, have the computer serviced. Refer to the safety and warranty information that is provided with your computer for a list of service and support telephone numbers. The mouse does not work. The computer does not respond to the mouse.
created by both diagnostic programs. You will need the log files when you speak to a Lenovo technical support representative. (The log file created by PC-Doctor for Windows is automatically saved in C:\PCDR\DETAILED.TXT.) PC-Doctor for Windows PC-Doctor for Windows is a diagnostic program that works through the Windows operating system.
3. Repeatedly press and release the F11 key as you turn on the computer. 4. When you hear beeps or see a logo screen, stop pressing the F11 key. The Rescue and Recovery workspace opens. 5. 6. 7. 8. 9. 10. Note: For some models, press the Esc key to enter Rescue and Recovery. From the Rescue and Recovery workspace, select Create diagnostic disks. Follow the instructions on the screen.
6. When the computer restarts, the diagnostic program opens automatically. Select the diagnostic test you want to run. Press the F1 key for additional help. PC-Doctor for Windows PE Depending upon your machine type and model, you either have PC-Doctor for DOS or PC-Doctor for Windows PE on your Lenovo computer. The PC-Doctor for Windows PE diagnostic program is part of the Rescue and Recovery workspace.
Non-optical mouse The non-optical mouse uses a ball to navigate the pointer. If the pointer on the screen does not move smoothly with the mouse, you might need to clean the mouse. To clean the non-optical mouse: Note: The following illustration might be slightly different from your mouse. 1 2 3 4 Retainer ring Ball Plastic rollers Ball cage To clean a mouse with a ball, follow the instructions below: 1. Turn off your computer. 2. Disconnect the mouse cable from the computer. 3.
11. Reconnect the mouse cable to the computer. 12. Turn your computer back on. Chapter 7.
46 User Guide
Chapter 8. Recovering software This chapter will help you become familiar with recovery solutions provided by Lenovo.
v Windows Vista: Use Product Recovery discs to restore your computer to the original factory contents only. When using Product Recovery discs on Windows XP, you are given the option to enter the Rescue and Recovery workspace and choose from a variety of recovery operations. When using Product Recovery discs on Windows Vista, you are prompted to insert your Product Recovery discs and are guided through the process of restoring from original factory contents only.
v v v v On a second hard disk drive installed in your computer On an externally attached USB hard disk drive On a network drive On recordable CDs or DVDs (a recordable CD or DVD drive is required for this option) After you have backed up your hard disk drive, you can restore the complete contents of the hard disk drive, restore selected files only, or restore only the Windows operating system and applications. To perform a backup operation using the Rescue and Recovery program, do the following: 1.
factory contents to the C: partition and leave the other partitions intact. Because the Rescue and Recovery workspace operates independently from the Windows operating system, you can restore the factory contents even if you cannot start the Windows operating system.
To create rescue media, do the following: 1. Open the Start menu from the Windows desktop, select All Programs, click ThinkVantage, then click Create Recovery Media. 2. In the Rescue Media area, select the type of rescue media you want to create. You can create rescue media using a CD, USB hard disk drive, or a second internal hard disk drive. 3. Click OK. 4. Follow the instructions on the screen.
2. Insert the Recovery Repair diskette into diskette drive A. 3. Turn on the computer and follow the instructions on the screen. Note: If the repair operation finishes without error, you will be able to access the Rescue and Recovery workspace by repeatedly pressing the F11 key while you restart your computer. When you hear beeps or see a logo screen, release the F11 key. You will also be able to access the Windows environment after the repair operation finishes.
Setting a rescue device in the startup sequence Before you start the Rescue and Recovery program from a CD, DVD, USB hard disk drive, or any external device, you must first change the startup sequence in the Setup Utility. To view or change the startup sequence, do the following: 1. With the computer turned off, repeatedly press and release the F1 key while you turn on the computer. 2. When the logo screen appears, or you hear a series of beeps, release the F1 key. 3.
54 User Guide
Chapter 9. Getting information, help, and service This chapter contains information about help, service, and technical assistance for products manufactured by Lenovo. Information resources This section describes how to access useful resources relating to your computing needs. Online Books folder The Online Books folder provides publications to help you set up and use your computer. The Online Books folder is preinstalled on your computer and requires no Internet access to view the publications.
v Service and support Note: ThinkVantage Technologies are only available on select Lenovo computers. To access the ThinkVantage Productivity Center program, open the Start menu from the Windows desktop, select All Programs, select ThinkVantage, and click Productivity Center. Access Help The Access Help online help system provides information about getting started, doing basic tasks, customizing settings for your personal preference, protecting data, expanding and upgrading, and troubleshooting.
Help and service This section contains information about obtaining help and service. Using the documentation and diagnostic programs If you experience a problem with your computer, see Chapter 7, “Troubleshooting and diagnostics,” on page 39. For information on additional resources to help you troubleshoot your computer problem, see “Information resources” on page 55.
If possible, be at your computer when you call.
Appendix A. Manual modem commands The following section lists commands for manually programming your modem. Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Command Mode until you dial a number and establish a connection. Commands can be sent to your modem from a PC running communication software or any other terminal devices. All commands sent to the modem must begin with AT and end with ENTER.
Command Function H1 Force modem off-hook (make busy) Note: H1 command is not supported for Italy I_ L_ M_ I0 Display product-identification code I1 Factory ROM checksum test I2 Internal memory test I3 Firmware ID I4 Reserved ID L0 Low speaker volume L1 Low speaker volume L2 Medium speaker volume L3 High speaker volume M0 Internal speaker off M1 Internal speaker on until carrier detected M2 Internal speaker always on M3 Internal speaker on until carrier detected and off while d
Extended AT commands Command Function &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command Mode after DTR toggle &D3 Resets modem after DTR toggle &F_ &F Recall factory default configuration &G_ &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800 Hz guard tone &K0 Disable flow control &K3 Enable RTS/CTS hardware flow
Command Function &W_ %E_ &V1 Display Last Connection Statistics &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 %E0 Disable auto-retrain %E1 Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,e,f Select modulation where: a=0, 1, 2, 3, 9, 10, 11, 12, 56, 64, 69; b=0-1; c=300-56000; d=30056000; e=0-1; and f=0-1. A, b, c, d, e, f default=12, 1, 300, 56000, 0, 0.
Fax Class 1 commands +FAE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing +FRM=n Receive data +FRS=n Receive silence +FTH=n Transmit data with HDLC framing +FTM=n Transmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class. +FAA=n Adaptive answer. +FAXERR Fax error value. +FBOR Phase C data bit order. +FBUF? Buffer size (read only). +FCFR Indicate confirmation to receive. +FCLASS= Service class.
+FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling. +FTSI: Report the transmit station ID.
Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix A.
66 User Guide
Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Television output notice The following notice applies to models that have the factory-installed television-output feature.
Index A diagnostic (continued) PC-Doctor for Windows 40, 41 PC-Doctor for Windows PE 40, 43 programs 40 Rescue and Recovery workspace 42, 43 running diskettes 42 running, CD image 42 diagnostics 39 diagnostics programs, using 57 disc, creating product recovery 47 diskette, creating and using a recovery repair 51 documentation, using 57 access help 56 administration, password 32 advanced settings 34 antivirus software, updating 11 arranging workspace 3 AT commands basic 59 extended 61 audio subsystem 12, 1
installing (continued) operating system 11 software 10 internal drives 12, 15, 18, 21 introduction v purchasing additional services R L Lenovo web site 56 lighting, glare 3 M manual modem commands 59 media, creating and using rescue 50 MNP/V.42/V.42bis/V.44, commands 62 modem commands basic AT 59 Extended AT 61 fax class 1 63 fax class 2 63 manual 59 MNP/V.42/V.42bis/V.
troubleshooting 39 troubleshooting, basic 39 turning on power 10 U updating (flashing) BIOS 35 antivirus software 11 operating system 11 system programs 35 updating (flashing) BIOS 36 user, password 32 using diagnostic programs 57 documentation 57 other services 58 passwords 31 recovery repair diskette, creating and using rescue media, creating and 50 Setup Utility 31 utility program, starting 31 51 V video subsystem 12, 15, 18, 21 viewing and changing settings 31 voice, commands 64 W warranty informati
72 User Guide
Part Number: 43C6566 Printed in USA (1P) P/N: 43C6566