ThinkStation Hardware Maintenance Manual Machine Types: 4223, 4228 and 4229
ThinkStation Hardware Maintenance Manual Machine Types: 4223, 4228 and 4229
Note: Before using this information and the product it supports, be sure to read and understand the Chapter 2 “Safety information” on page 3 and Appendix A “Notices” on page 109. First Edition (April 2012) © Copyright Lenovo 2012. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents Chapter 1. About this manual . . . . . . 1 Chapter 7. Configuring RAID . . . . . 43 Important Safety Information . . . . . . . . . . Configuring RAID with Intel RSTe . . . . . . . Installing SATA or SAS hard disk drives . . . Configuring SATA or SAS RAID functionality with the Intel RSTe configuration utility . . . Quick RAID setup using the LSI MegaRAID BIOS configuration utility . . . . . . . . . . . . . Installing SATA or SAS hard disk drives . . .
Installing or replacing a hard disk drive . Installing or replacing a hard disk drive enablement module . . . . . . . . . Replacing the front audio and USB assembly . . . . . . . . . . . . . Replacing the internal speaker. . . . . Installing or replacing the microprocessor Replacing the system board . . . . . Replacing the power supply assembly . Completing the parts replacement . . . . . 83 . . 87 . . . . . . . . . . . . Chapter 11. Additional service information . . . . . . . . . . . . .
Chapter 1. About this manual This manual provides service and reference information for ThinkStation® computers listed on the front cover. This manual is intended only for trained service personnel who are familiar with Lenovo® computer products. Before servicing a Lenovo computer product, be sure to read Chapter 2 “Safety information” on page 3. Chapter 8 “Symptom-to-FRU Index” on page 49 and Chapter 11 “Additional service information” on page 105 are not specific to any machine type.
2 ThinkStation Hardware Maintenance Manual
Chapter 2. Safety information This chapter contains the safety information that you need to be familiar with before servicing a computer. General safety Follow these rules to ensure general safety: • Observe good housekeeping in the area of the machines during and after maintenance. • When lifting any heavy object: 1. Ensure you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force.
Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from an electric shock. • Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet.
Voltage-selection switch Some computers are equipped with a voltage-selection switch located near the power-cord connection point on the computer and some computers do not have a voltage-selection switch. Before you install your computer or relocate your computer to another country or region, you must be certain that you have matched your computer to the voltage available at your electrical outlet.
3. Check the power cord for: a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and frame ground. b. The power cord should be the appropriate type as specified in the parts listings. c. Insulation must not be frayed or worn. 4. Remove the cover. 5. Check for any obvious alterations. Use good judgment as to the safety of any alterations. 6.
• English • Arabic • Brazilian/Portuguese • Chinese (simplified) • Chinese (traditional) • French • German • Hebrew • Italian • Korean • Spanish DANGER Electrical current from power, telephone and communication cables is hazardous. To avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. • Connect all power cords to a properly wired and grounded electrical outlet.
it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations. CAUTION: When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers.
2 1 Chapter 2.
≥18 kg (37 lbs) 10 ThinkStation Hardware Maintenance Manual ≥32 kg (70.5 lbs) ≥55 kg (121.
2 1 PERIGO A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa. Para evitar risco de choque elétrico: • Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. • Conecte todos os cabos de alimentação a tomadas elétricas corretamente instaladas e aterradas. • Todo equipamento que for conectado a este produto deve ser conectado a tomadas corretamente instaladas.
Não: • Jogue ou coloque na água • Aqueça a mais de 100°C (212°F) • Conserte nem desmonte Descarte a bateria conforme requerido pelas leis ou regulamentos locais. PRECAUCIÓN: Quando produtos a laser (como unidades de CD-ROMs, unidades de DVD-ROM, dispositivos de fibra ótica ou transmissores) estiverem instalados, observe o seguinte: • Não remova as tampas. A remoção das tampas de um produto a laser pode resultar em exposição prejudicial à radiação de laser.
2 1 Chapter 2.
2 1 14 ThinkStation Hardware Maintenance Manual
Chapter 2.
2 1 DANGER Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenter un danger. Pour éviter tout risque de choc électrique : • Ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration de ce produit au cours d'un orage. • Branchez tous les cordons d'alimentation sur un socle de prise de courant correctement câblé et mis à la terre.
Connexion Déconnexion 1. Mettez les unités HORS TENSION. 1. Mettez les unités HORS TENSION. 2. Commencez par brancher tous les cordons sur les unités. 2. Débranchez les cordons d'alimentation des prises. 3. Branchez les câbles d'interface sur des connecteurs. 4. Débranchez tous les câbles des unités. 3. Débranchez les câbles d'interface des connecteurs. 4. Branchez les cordons d'alimentation sur des prises. 5. Mettez les unités SOUS TENSION.
≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ATTENTION: Soulevez la machine avec précaution. ATTENTION: L'interrupteur de contrôle d'alimentation de l'unité et l'interrupteur dubloc d'alimentation ne coupent pas le courant électrique alimentantl'unité. En outre, le système peut être équipé de plusieurs cordonsd'alimentation. Pour mettre l'unité hors tension, vous devez déconnectertous les cordons de la source d'alimentation.
• Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerken und Modems ist vor dem Öffnen des Gehäuses zu unterbrechen, sofern in den Installations- und Konfigurationsprozeduren keine anders lautenden Anweisungen enthalten sind. • Zum Installieren, Transportieren und Öffnen der Abdeckungen des Computers oder der angeschlossenen Einheiten die Kabel gemäß der folgenden Tabelle anschließen und abziehen.
Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine Lupen oder Spiegel verwenden. Strahlungsbereich meiden. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung für die Einheit nicht unterbrochen. Die Einheit kann auch mit mehreren Netzkabeln ausgestattet sein.
Chapter 2.
2 1 PERICOLO La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di comunicazione può essere pericolosa. Per evitare il rischio di scosse elettriche: • Non collegare o scollegare qualsiasi cavo oppure effettuare l'installazione, la manutenzione o la riconfigurazione del prodotto durante un temporale. • Collegare tutti i fili elettrici a una presa di alimentazione correttamente cablata e dotata di messa a terra.
• Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di segnale. • Non accendere assolutamente apparecchiature in presenza di incendi, perdite d'acqua o danno strutturale. • Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il modem prima di aprire i coperchi del dispositivo, salvo istruzioni contrarie relative alle procedure di installazione e configurazione.
PERICOLO Alcune unità laser contengono un diodo laser di Classe 3A o Classe 3B. Tener presente quanto segue: Aprendo l'unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici ed evitare l'esposizione al fascio. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ATTENZIONE: Prestare attenzione nel sollevare l'apparecchiatura.
Chapter 2.
2 1 PELIGRO La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de comunicación puede ser peligrosa. Para evitar el riesgo de descarga eléctrica: • No conecte ni desconecte los cables ni realice ninguna tarea de instalación, mantenimiento o reconfiguración de este producto durante una tormenta eléctrica. • Conecte todos los cables de alimentación a tomas de corriente debidamente cableadas y conectadas a tierra.
• Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y los módems conectados antes de abrir las cubiertas de los dispositivos, a menos que se indique lo contrario en los procedimientos de instalación y configuración. • Conecte y desconecte los cables, como se describe en la tabla siguiente, cuando instale, mueva o abra las cubiertas de este producto o de los dispositivos conectados. Para conectar Para desconectar 1. APÁGUELO todo. 1. APÁGUELO todo. 2.
Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase 3B. Tenga en cuenta lo siguiente: Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo láser, ni siquiera con instrumentos ópticos, y evite exponerse directamente al rayo láser. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) PRECAUCIÓN: Adopte procedimientos seguros al levantar el equipo.
Chapter 3. General information This chapter provides general information that applies to all machine types supported by this publication. Specifications This section lists the physical specifications for your computer. Dimensions Width: 210 mm (8.3 inches) Height: 485 mm (19.1 inches) (floor to top of handle) Depth: 602 mm (23.7 inches) Weight Maximum configuration as shipped: 27.5 kg (60.
The following table lists the programs that you can access from the Lenovo ThinkVantage Tools program. To access a program, double-click the corresponding icon. Table 1.
Note: If the Enhanced Backup and Restore icon in the Lenovo ThinkVantage Tools program is dimmed, it indicates that you need to install the ThinkVantage Rescue and Recovery program manually before enabling its features. To install the ThinkVantage Rescue and Recovery program, do the following: 1. Click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools, and double-click Enhanced Backup and Restore. 2. Follow the instructions on the screen. 3.
32 ThinkStation Hardware Maintenance Manual
Chapter 4. General Checkout Attention The drives in the computer you are servicing might have been rearranged or the drive startup sequence might have been changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or programs can be overwritten if you select an incorrect drive. General error messages appear if a problem or conflict is found by an application program, the operating system, or both.
– If it has been working, what changes were made prior to it failing? – Is this the original reported failure? • Diagnostics version – Type and version level • Hardware configuration – Print (print screen) configuration currently in use – BIOS level • Operating system software – Type and version level Notes: To eliminate confusion, identical systems are considered identical only if they: 1. Are the exact machine type and models 2. Have the same BIOS level 3.
Chapter 5. Diagnostics The diagnostic program is used to test hardware components of your computer. The diagnostic program can also report operating-system-controlled settings that interfere with the correct operation of your computer. You can use the preinstalled diagnostic program to diagnose computer problems, if your computer is running the Windows operating system. Notes: 1. Your computer is preinstalled with the Lenovo Solution Center program for diagnostic purposes.
36 ThinkStation Hardware Maintenance Manual
Chapter 6. Using the Setup Utility program The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1. Make sure your computer is turned off. 2. Repeatedly press and release the F1 key when turning on the computer.
Password considerations A password can be any combination of up to 64 alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised.
Note: A password can be any combination of up to 64 alphabetic and numeric characters. For more information, see “Password considerations” on page 38. Erasing lost or forgotten passwords (clearing CMOS) This section provides instructions on how to erase lost or forgotten passwords, such as a user password. To erase a lost or forgotten password, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer.
Selecting a temporary startup device Use this procedure to select a temporary startup device. Note: Not all discs and hard disk drives are bootable. 1. Turn off your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device Menu window displays, release the F12 key. 3. Select the desired startup device and press Enter. The computer will start up from the device you selected.
The after power loss feature enables your computer to wake up when the power supply resumes after a sudden loss of electricity. To enable the after power loss feature, do the following: 1. Start the Setup Utility program. 2. From the Setup Utility program main menu, select Power ➙ After Power Loss, and press Enter. 3. Select Power On and press Enter. 4. Press F10 to save changes and exit the Setup Utility program. Press Enter when prompted to confirm the exit.
42 ThinkStation Hardware Maintenance Manual
Chapter 7. Configuring RAID This chapter provides instructions on how to install hard disk drives and configure Redundant Array of Independent Disks (RAID) for your computer. Depending on your computer model, RAID can be enabled by Intel Rapid Storage Technology enterprise (RSTe) or the LSI MegaRAID BIOS. Note: The RAID configuration information described in this chapter is only applicable in the Windows environment.
• If five SATA hard disk drives or solid state drives are installed, the SATA hard disk drive enablement module (one to five hard disk drives) is required. • If any SAS hard disk drives are installed, the SAS hard disk drive enablement module (one to five hard disk drives) is required. For more information about the hard disk drive enablement module, refer to “Installing or replacing a hard disk drive enablement module” on page 87.
• RAID Level 0 • RAID Level 1 • RAID Level 10 • RAID Level 5 c. Disks: Press Enter to enter the SELECT DISKS MENU window. Follow the instructions at the bottom of the menu to select hard disk drives, and then press Enter to complete the configuration. d. Strip Size: Press the up and down arrow keys to select a strip size. e. Capacity: Customize the capacity of the RAID volume. The default RAID volume is the largest value. 4. Press Enter to finish configuring all the five options.
using this adapter, refer to the complete MegaRAID SAS Software User Guide that is available at http://support.lenovo.com/en_US/guides-and-manuals/detail.page?DocID=UM007543.
Entering the LSI MegaRAID BIOS configuration utility This section provides instructions on how to enter the LSI MegeRAID BIOS configuration utility. To enter the LSI MegaRAID BIOS configuration utility, do the following: 1. During the computer startup, follow the instructions on the screen. 2. Press Ctrl+H to enter the CONTROLLER SELECTION window. 3. Select the controller you want to configure, and then click Start to enter the LSI MegaRAID BIOS configuration utility.
Deleting RAID volumes using the LSI MegaRAID BIOS configuration utility This section provides instructions on how to delete RAID volumes using the LSI MegaRAID BIOS configuration utility. To delete RAID volumes using the LSI MegaRAID BIOS configuration utility, do the following: 1. Enter the LSI MegaRAID BIOS configuration utility. See “Entering the LSI MegaRAID BIOS configuration utility” on page 47. 2. Click the virtual hard disk drives you want to delete, and then the Virtual Drive window is displayed.
Chapter 8. Symptom-to-FRU Index The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first. Always begin with Chapter 4 “General Checkout” on page 33. This index can also be used to help you decide which FRUs to have available when servicing a computer. If you are unable to correct the problem using this index, go to “Undetermined problems” on page 53. Notes: • If you have both an error message and an incorrect audio response, diagnose the error message first.
The following tables describes beep symptoms. Beep Symptom FRU/Action 2 short beeps CMOS setting error Perform the following actions in order. 1. Start the Setup Utility program and press F10 to save and exit. See Chapter 6 “Using the Setup Utility program” on page 37. 2. Start the Setup Utility program and press F9 to load defaults and then press F10 to save and exit. 3. Perform a Boot block recovery. See “Recovering from a POST/BIOS update failure” on page 106.
POST Error Message Description/Action CMOS battery failed The CMOS battery is no longer functional. Replace the battery. CMOS checksum error - defaults loaded Checksum of CMOS is incorrect. The computer loads the default configuration settings. This error might indicate that CMOS has become corrupt due to a weak CMOS battery. CPU at nnnn nnnn is the running speed of the microprocessor.
Message/Symptom Computer will not RPL from server FRU/Action 1. Ensure that network is in startup sequence as first device or first device after diskette. 2. Ensure that network adapter is enabled for RPL. 3. Network adapter (Advise network administrator of new MAC address) Computer will not perform a Wake On LAN® (if applicable) 1. Check power supply and signal cable connections to network adapter. 2. Ensure that the operating system settings are set to enable Wake on LAN. 3.
Message/Symptom Printer problems FRU/Action 1. Printer 2. System board Program loads from the hard disk with a known-good diagnostics diskette in the first 3.5-inch diskette drive 1. Run the Setup Utility program and check Startup sequence. 2. Diskette drive 3. Diskette drive cable 4. System board 5. Power supply RPL computer cannot access programs from its own hard disk. 1. If network administrator is using LCCM Hybrid RPL, check startup sequence: a. First device - network b.
If all devices and adapters have been removed, and the problem continues, replace the system board.
Chapter 9. Locations This chapter introduces the locations of the computer hardware components. Locating connectors, controls, and indicators on the front of your computer Figure 1 “Front connector, control, and indicator locations” on page 55 shows the locations of the connectors, controls, and indicators on the front of your computer. Figure 1. Front connector, control, and indicator locations 1 Optical drive eject/close button 6 1394 connector (available on some models) 2 USB 2.
Locating connectors on the rear of your computer Figure 2 “Rear connector locations” on page 56 shows the locations of the connectors on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer. Figure 2. Rear connector locations 1 Power cord connector 7 Audio line-out connector 2 PS/2 keyboard and mouse connectors (optional) 8 Microphone connector 3 Ethernet connectors (2) 9 USB 3.
Figure 3. Locating major FRUs and CRUs Chapter 9.
The following table lists the major FRUs shown in Figure 3 “Locating major FRUs and CRUs” on page 57 and identifies which FRUs also are self-service CRUs or optional-service CRUs. Notes: • Self-service CRUs: These CRUs unplug or are secured by no more than two screws. Examples of these types of CRUs include the keyboard, the mouse, any USB device, and the power cord. Other self-service CRUs depending on product design might include memory modules, adapter cards, hard disk drives, and optical drives.
Figure 4.
20 Clear CMOS (Complementary Metal Oxide Semiconductor) / Recovery jumper 48 PCI Express x16 card slot 21 SATA port 4 49 PCI Express x4 card slot (x16 mechanical) 22 SATA port 3 50 Rear fan connector 23 Media card reader connector 51 Microprocessor 2 memory slot 1 (DIMM1) 24 Front panel connector 52 Microprocessor 2 memory slot 5 (DIMM5) 25 Front USB connector 53 Microprocessor 2 memory slot 2 (DIMM2) 26 Hard disk drive enablement module connector 54 Microprocessor 2 memory slot 6 (DIMM6) 27 A
Locating internal drives Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and enable your computer to read other types of media. Internal drives are installed in bays. In this manual, the bays are referred to as bay 1, bay 2, and so on.
62 ThinkStation Hardware Maintenance Manual
Chapter 10. Replacing FRUs This chapter provides information about the FRU replacement instructions. Important Be sure to read and understand Chapter 2 “Safety information” on page 3 before replacing any FRU. These precautions and guidelines will help you work safely. Note: FRU replacements are to be done only by trained service technicians. Installing or replacing hardware This section provides instructions on how to install or replace hardware for your computer.
required connector. Then, use the instructions that come with the option to help you make the connection and install any software or device drivers that are required for the option. Removing the computer cover Attention: Do not open your computer or attempt any repair before reading and understanding the “Important Safety Information” on page 1. This section provides instructions on how to remove the computer cover.
5. Disengage the cover latch 1 and remove the cover. Place the cover on a flat surface. Figure 6. Removing the computer cover Removing and reinstalling the front bezel Attention: Do not open your computer or attempt any repair before reading and understanding the “Important Safety Information” on page 1. This section provides instructions on how to remove and reinstall the front bezel. To remove and reinstall the front bezel, do the following: 1.
3. Remove the front bezel by releasing the two plastic tabs on the left side and pivoting the front bezel outward. Figure 7. Removing the front bezel 4. To reinstall the front bezel, align the three plastic tabs on the right side of the front bezel with the corresponding holes in the chassis, and then pivot the front bezel inwards until the two plastic tabs snaps into position on the left side. What to do next: • To work with another piece of hardware, go to the appropriate section.
Figure 8. Opening the PCI card retainer 4. Depending on whether you are installing or replacing a PCI card, do one of the following: • If you are installing a PCI card, remove the appropriate metal card slot cover. • If you are replacing an old PCI card, grasp the old card that is currently installed and gently pull it out of the card slot. Chapter 10.
Figure 9. Removing a PCI card Notes: a. The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small amount until it is removed from the card slot.
b. If the card is held in place by a retaining latch, press the card retaining latch 1 as shown to disengage the latch. Grasp the card and gently pull it out of the card slot. 5. Remove the new PCI card from its static-protective package. 6. Install the new card into the appropriate card slot on the system board. See “Locating parts on the system board” on page 58. 7. Pivot the PCI card latch to the closed position to secure the PCI card.
Turn off the computer and wait three to five minutes to let the computer cool before installing or replacing a memory module. Your computer has 16 slots for installing or replacing DDR3 ECC UDIMMs or DDR3 ECC RDIMMs. When installing or replacing a memory module, use the following guidelines: • Use either DDR3 ECC UDIMMs or DDR3 ECC RDIMMs for your computer. Do not install both the UDIMMs and RDIMMs into the same computer. • Use 2 GB, 4 GB, or 8 GB UDIMMs in any combination up to a maximum of 128 GB.
• If you are replacing an old memory module, open the retaining clips and gently pull the memory module out of the memory slot. Figure 11. Removing a memory module • If you are installing a memory module, open the retaining clips of the memory slot into which you want to install the memory module. Figure 12. Opening the retaining clips Chapter 10.
9. Position the new memory module over the memory slot. Make sure that the notch 1 on the memory module aligns correctly with the slot key 2 on the system board. Push the memory module straight down into the slot until the retaining clips close. Figure 13. Installing a memory module 10. To install the memory fan duct, secure the rear of the fan duct with the retaining clips of the memory slots, and then pivot the fan duct downward until the fan duct snaps into position. Figure 14.
This section provides instructions on how to install or replace the optical drive. To install or replace an optical drive, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 64. 3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 65. 4. Locate the optical drive. See “Locating major FRUs and CRUs” on page 56. 5.
6. Install the optical drive retainer on the side of the new optical drive. Figure 16. Installing the optical drive retainer 7. Slide the new optical drive into the drive bay from the front of the computer until the optical drive snaps into position. Figure 17.
8. Connect the signal cable and the power cable to the new optical drive. Figure 18. Connecting the optical drive 9. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 65. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
6. Press the blue retaining clip 1 to remove the card reader out of the chassis. Figure 19. Removing the card reader 7. Install the card reader retainer on the side of the new card reader. Figure 20.
8. Slide the card reader with retainer into the card reader drive bay until it snaps into position. Figure 21. Installing the card reader 9. Reconnect the card reader cable to the system board. See “Locating parts on the system board” on page 58. 10. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 65. What to do next: • To work with another piece of hardware, go to the appropriate section.
Refer to the “Lithium battery notice” in the ThinkStation Safety and Warranty Guide for information about replacing and disposing of the battery. To replace the battery, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 64. 3. Locate the battery. See “Locating parts on the system board” on page 58. 4. Remove the old battery. Figure 22. Removing the old battery 5. Install a new battery.
CAUTION: The heat sink and fan assembly might be very hot. Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To replace the heat sink and fan assembly, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 64. 3. Lay the computer on its side for easier access to the system board. 4.
9. Follow the following sequence to install the four screws to secure each new heat sink and fan assembly. Do not over-tighten the screws. a. Partially tighten screw 1 , then fully tighten screw 2 , and then fully tighten screw 1 . b. Partially tighten screw 3 , then fully tighten screw 4 , and then fully tighten screw 3 . 10. Connect the heat sink and fan assembly cables to the microprocessor fan connectors on the system board. See “Locating parts on the system board” on page 58.
5. Press the tab, and then pivot the hard disk drive fan outward to remove it from the chassis. Figure 25. Removing the hard disk drive fan assembly 6. Position the hard disk drive fan, and then pivot the fan to insert the tab into the chassis. 7. Reconnect the hard disk drive fan cable to the system board. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
5. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly by breaking or cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis. Note: The new rear fan assembly will have four new rubber mounts attached. Figure 26. Removing the rear fan assembly 6. Install the new rear fan assembly by aligning the new rubber mounts with the corresponding holes in the chassis and push the rubber mounts through the holes.
Figure 27. Installing the rear fan assembly 7. Connect the rear fan assembly cable to the system fan connector on the system board. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 104. Installing or replacing a hard disk drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Important Safety Information” on page 1.
2. Remove the computer cover. See “Removing the computer cover” on page 64. 3. Locate the hard disk drive. See “Locating internal drives” on page 61. 4. Disconnect the signal cable and the power cable from the hard disk drive. 5. Pull the bracket handle out to remove the hard disk drive from the chassis. Figure 28. Removing the hard disk drive 6. Flex the sides of the bracket to remove the hard disk drive from the bracket.
7. To install a new hard disk drive into the bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 29. Installing the hard disk drive into the bracket Note: If you are replacing or installing a 2.5-inch hard disk drive, you need to install it into a 2.5 to 3.5-inch converter bracket. Then install the 2.
Figure 31. Installing the hard disk drive 9. Connect the signal cable and the power cable to the new hard disk drive. Note: If you are installing SAS hard disk drives, you must connect the signal cables and power cables to the SAS-to-SATA conversion adapter before you connect them to the hard disk drive. Figure 32.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 104. Installing or replacing a hard disk drive enablement module Attention: Do not open your computer or attempt any repair before reading and understanding the “Important Safety Information” on page 1. This section provides instructions on how to install or replace a hard disk drive enablement module.
7. To install a new hard disk drive enablement module, align the hole in the hard disk drive enablement module with the plastic standoff on the system board, and then position the hard disk drive module over the corresponding connector on the system board. Figure 34. Installing a new hard disk drive enablement module 8. Reinstall the hard disk drive fan assembly and close the PCI card retainer. See “Replacing the hard disk drive fan assembly” on page 80.
5. Disconnect the front audio and USB assembly cables from the system board. See “Locating parts on the system board” on page 58. Note: Make sure you note the locations of the cables when you disconnect the cables from the system board. 6. Remove the two screws that secure the front audio and USB assembly bracket, and then remove the bracket from the chassis. Figure 35. Removing the two screws that secure the front audio and USB assembly to the chassis 7.
Note: The internal speaker is only available on some models. To replace the internal speaker, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 64. 3. Locate the internal speaker connector and disconnect the internal speaker cable form the system board. See “Locating parts on the system board” on page 58. 4.
Installing the second microprocessor Attention: Do not open your computer or attempt any repair before reading and understanding the “Important Safety Information” on page 1. This topic provides instructions on how to install the second microprocessor. Depending on the model, your computer might come with one or two microprocessors.
5. Open the small handle 2 by gently pressing down the small handle, and then pulling the small handle a little bit outward to release it from the secured position. Then, open the other small handle 1 by following the same instructions. Ensure that the small handles are in the fully open position. Note: There are two marks on the microprocessor retainer. You need to open the small handle marked first, and then you can open the other small handle marked with . with Figure 37. Opening the handles 6.
• Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Figure 39. Removing the microprocessor 8. Touch the static-protective package that contains the new microprocessor to any unpainted surface on the outside of the computer. Then, remove the new microprocessor from the package. 9. Remove the new microprocessor from the protective cover that protects the gold contacts on the bottom of the new microprocessor.
10. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align the notches 1 on it with the tabs 2 in the microprocessor socket. Then, carefully lower the new microprocessor straight down into the microprocessor socket. Note: The small triangle 3 on one corner of the new microprocessor is the microprocessor orientation indicator. The new microprocessor is in the correct orientation when this indicator faces the beveled corner 4 of the microprocessor socket.
12. Gently press down the small handle 1 , and then push the handle inward to secure it. Then gently press down the small handle 2 and push the handle inward to lock the microprocessor retainer into position and secure the new microprocessor in the socket. Note: There are two marks on the microprocessor retainer. Ensure that you close the small handle first, and then close the small handle marked with . Always follow the marked with correct sequence when you close the small handles. Figure 43.
• Use any documentation that comes with the microprocessor option kit and follow those instructions in addition to the instructions in this topic. • Your microprocessor, socket, and socket cover might look slightly different from the illustrations in this topic. To replace a microprocessor, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer.
Figure 45. Opening the microprocessor retainer 8. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor socket. Place the old microprocessor on a static-protective surface. Notes: • Do not touch the gold contacts on the bottom of the microprocessor. • Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Figure 46. Removing the microprocessor 9.
10. Remove the new microprocessor from the protective cover that protects the gold contacts on the bottom of the new microprocessor. Do not touch the pins on the microprocessor socket or the gold contacts on the bottom of the new microprocessor. Figure 47. Do not touch the pins 11. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align the notches 1 on it with the tabs 2 in the microprocessor socket.
12. Pivot the microprocessor retainer downward to close the retainer. Figure 49. Closing the microprocessor retainer 13. Gently press down the small handle 1 , and then push the handle inward to secure it. Then gently press down the small handle 2 and push the handle inward to lock the microprocessor retainer into position and secure the new microprocessor in the socket. Note: There are two marks on the microprocessor retainer.
CAUTION: The heat sink and microprocessor might be very hot. Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. Note: Before replacing the system board, make sure you have a retention module for the new system board. To replace the system board, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer.
12. Carefully lift the failing system board out of the chassis. 13. Position the new system board into the chassis so that the screw holes in the new system board are aligned with those in the chassis. Install the ten screws that secure the system board to the chassis by following the sequence from 10 to 1 . 14. Remove the microprocessor socket cover(s) from the new system board. 15.
Figure 53. Securing the microprocessor in the socket 3. Align the notch 1 of the microprocessor socket cover with the alignment key 2 of the microprocessor socket. Lower the socket cover straight down into the microprocessor socket on the system board. Figure 54. Installing the microprocessor socket cover Note: Your microprocessor socket and cover might look slightly different from the illustration.
Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. CAUTION: The heat sink and microprocessor might be very hot. Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To replace the power supply assembly, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer.
12. To complete the installation or replacement, go to “Completing the parts replacement” on page 104. Completing the parts replacement After completing the installation or replacement for all parts, you need to reinstall the computer cover and reconnect cables. Depending on the parts you installed or replaced, you might need to confirm the updated information in the Setup Utility program. Refer to Chapter 6 “Using the Setup Utility program” on page 37.
Chapter 11. Additional service information This chapter provides additional information that the service representative might find helpful. Security features Security features in this section include the following: • Passwords • Vital Product Data • Management Information Format (MIF) Hardware-controlled passwords Hardware-controlled passwords are set using the Setup Utility program. For more information about passwords, see “Using passwords” on page 37.
Note: You can download a self-starting bootable disc image (known as an ISO image) with the system program updates to create a system-program-update disc. Go to: http://www.lenovo.com/support. To update (flash) the BIOS from a disc, do the following: 1. Turn off your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device Menu window opens, release the F12 key. 3. From the Startup Device Menu window, select the desired optical drive as the startup device.
5. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and pin 3). 6. Reconnect any cables that were disconnected and reinstall the PCI card if removed. 7. Reinstall the computer cover and reconnect the power cords for the computer and monitor to electrical outlets. See “Completing the parts replacement” on page 104. 8. Turn on the computer and then insert the POST and BIOS update (flash update) disc into the optical drive. Wait a few minutes.
Table 2. DIMM type and speed: PC3-10600E DIMM operating voltage 1.5 V Microprocessor model Memory frequency Intel Xeon E5-2603, E5-2609 1066 MHz Intel Xeon E5-2620, E5-2630/2630L, E5-2637, E5-2640, E5-2643, E5-2667, E5-2650/2650L, E5-2660, E5-2665, E5-2670, E5-2680, E5-2685, E5-2690 1333 MHz Table 3. DIMM type and speed: PC3-10600R DIMM operating voltage 1.35 V, 1.
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Television output notice The following notice applies to models that have the factory-installed television-output feature. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Index A Administrator, password FRU part numbers 1, 55, 58, 63 38 H B hard disk drive enablement module, replacing hard disk drive fan assembly, replacing 80 hard disk drive, replacing 83 heat sink and fan assembly, replacing 78 battery, replacing 77, 102 boot-block recovery 106 C card reader, replacing 75 changing password 38 startup device sequence 40 CMOS, clearing 39 components, internal 56 computer cover removing 64 computer cover, reinstalling 104 connectors rear 56 connectors, controls, indica
slots 66 physical specifications 29 Power-On, Password 38 using passwords 37 Setup Utility 37 R V rear connectors 56 rear fan assembly, replacing 81 recovering from a POST/BIOS update failure 106 recovery boot-block 106 removing computer cover 64 replacing battery 77, 102 card reader 75 hard disk drive 83 hard disk drive enablement module 87 heat sink and fan assembly 78 viewing and changing settings S security enabling or disabling 39 selecting startup device 39 temporary startup device 40 Self-servi
