IMPRESSA F50/F5/F505 Art. Nr.
Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Consiglio JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.jura.
Fig. 1 Fig. 2 Fig. 3 Fig. 6 Fig. 7 Fig. 8 Fig. 4 Fig. 5 Fig. 9 Fig. 10 Fig. 14 Fig. 15 2 1 3 B Fig. 11 Fig. 12 Fig. 16 Fig.17 Fig.
Control elements 11 22 1. Rotary Switch 13 2. Illuminated ring 3. ON/OFF key 4. Programming key 5. Draw-off key 1 cup Rotary Switch 6. Draw-off key 2 cups 12 10 9 13 3 4 5 6 7 8 7. Maintenance key 8. Steam pre-selection key 9. Display dialog system 10. Water tank with carrying handle 14 2 11. Filler funnel for pre-ground coffee: 12. Bean tank cover 1 13. Aroma preservation cover 14. Steam/hot water draw-off valve 15/16 17 18 15. Replaceable 2-stage frothing jet see Fig 6 16.
Contents 1. Safety information..........................................page 1.1 Warning ..............................................page 1.2 Precautions ..........................................page 2. Preparing the IMPRESSA................................page 2.1 Check supply voltage ..............................page 2.2 Check electrical fuse ..............................page 2.3 Fill water tank......................................page 2.4 Fill coffee beans....................................page 2.
Introduction 1.2 Precautions Thank you for purchasing the IMPRESSA. To ensure perfect functioning of your IMPRESSA, carefully read this operating manual and keep it for future reference. Should you need more information or if you encounter particular problems not specified in these operating instructions in sufficient detail, either contact us directly or contact your local authorized dealer.
2.3 Fill water tank Only use fresh, cold water. Never fill in milk, mineral water or other liquids. Remove the water tank and rinse it with cold tap water thoroughly (Fig. 4). Then fill the water tank and reinstall it. Make sure to install the tank properly, it must engage audibly. 2.
FILLING SYSTEM CLOSE TAP Close the steam / hot water draw-off tap (14). HEATING PRESS RINSE Press the maintenance key (7). Machine carries out a rinsing operation. RINSING READY If BEANS FILL is displayed, press the coffee draw-off key again. Machine not filled with coffee beans yet. To get an excellent froth, adjust the coffee spout (17) to the size of your cup (Fig. 3). 4. Adjusting the water hardness Water is heated in the IMPRESSA.
5. Installation of Claris plus filter cartridges If the Claris plus filter cartridge is installed properly, de-scaling of the coffee machine is no longer required. For more information on the Claris plus filter cartridge refer to brochure «Claris plus. Hard on limescale. Gentle on your coffee machine.» 5.1 Installing the filter Fold up the cartridge holder. Install the filter cartridge in the water tank, applying a gentle pressure (Fig. 1). Fold down the cartridge holder again until it engages audibly.
6. Rinsing the IMPRESSA 8. Drawing off 1 cup of coffee When the IMPRESSA is switched off and has cooled down, a rinsing operation is started when the machine is switched on again. When the machine is switched off, a rinsing operation is started automatically. Switch on the IMPRESSA using the ON/OFF key HEATING PRESS RINSE Press the maintenance key (7). RINSING READY (3). You can choose among three strengths at the push of a button.
9. Drawing off 2 cups of coffee Selecting the coffee strength is not possible when drawing off 2 cups of coffee. You will draw off 2 mild cups automatically. You can adjust the water quantity before the draw-off operation using the Rotary Switch (1). The adjusted value (ML) refers to 1 cup. You can stop the draw-off operation at any time by pressing any coffee draw-off key. You can check the water quantity used for the last draw-off operation by pressing the Rotary Switch (1).
11. Drawing off hot water If you do not change the settings using the Rotary Switch (1), the water quantity last adjusted will be drawn off automatically. Install the hot water nozzle (see Fig. 5 ) to obtain perfect water flow. Do not replace the replaceable hot water nozzle (16) directly after drawing off water, because the nozzle is hot after the draw-off operation.
STEAM READY To draw off steam, open the steam/hot water draw-off tap (14) (Fig. 13). The illuminated ring (2) is active. You can adjust the steam draw-off time individually by turning the Rotary Switch (1) until the required SEC are displayed.
13.3 Cleaning the Professional-Cappuccino Frother The Professional-Cappuccino Frother must be cleaned after each draw-off operation. Fill water in a container and immerse the hose in it. Draw off steam until the water/steam mixture is clean. If necessary, disassemble the Professional-Cappuccino Frother and thoroughly rinse the flow regulator with water (Fig. 16). For proper cleaning, use the JURA Auto Cappuccino Cleaning Agent This is available at your authorized dealer. Daily cleaning is recommended.
Turn the Rotary Switch (1) until Aroma is displayed. AROMA Press the Rotary Switch (1). ROBUST Turn the Rotary Switch (1) until the following message is displayed: STANDARD To confirm the new aroma settings, press the Rotary Switch (1). AROMA Press the programming key (4) to quit the programming mode or select the next programming item using the Rotary Switch (1). READY 15.4 Programming the temperature READY Press programming key (4) until FILTER appears.
If the machine is disconnected from power supply, the time must be programmed again. 15.6 Programming the automatic switch-on time You must programme the time (Chapter 15.5) if you want to use the automatic switch-on function. READY Press programming key (4) until FILTER appears. The illuminated ring (2) is active. Turn the Rotary Switch (1) until MACHINE ON is displayed. MACHINE ON Now press the Rotary Switch (1) to start programming the switch-on time.
READY Press programming key (4) until FILTER appears. The illuminated ring (2) is active. Turn the Rotary Switch (1) until CUPS MADE is displayed. CUPS MADE Now press the Rotary Switch (1) to start programming the item CUPS MADE The total number of drawn off products is displayed.
Press the programming key (4) to quit the programming mode or select the next programming item using the Rotary Switch (1). READY 15.11 Programming the display for ML/OZ READY Press the Rotary Switch (1) until FILTER – / appears The illuminated ring (2) is active. Turn the Rotary Switch (1) until DISPLAY appears Press the Rotary Switch (1) ML/OZ appears Press the Rotary Switch (1) e.g. ML Select a setting of your choice. Press the Rotary Switch (1) to save the setting.
16.4 Fill coffee beans 16.7 IMPRESSA decalcify During operation, the machine will calcify. The degree of scaling depends on the hardness of the water in your region. The machine will inform you when de-scaling is required. You can still draw off coffee or hot water/steam. However, we recommend that you should de-scale the machine (Chapter 18) within the next few days. FILL BEANS Refill beans as described in Chapter 2.4.
16.9 Emptying the system Precondition: IMPRESSA switched off This operation is required to protect the IMPRESSA against frost damage during transports. Place a container under the replaceable hot water nozzle (16). Press the steam preselection key (8) until the following message is displayed: OPEN TAP EMPTYING CLOSE TAP The IMPRESSA is switched off. 17. Cleaning Your IMPRESSA features an integrated cleaning program. The cleaning operation will take some 15 min.
18. De-scaling Your IMPRESSA features an integrated de-scaling program. The de-scaling operation will take some 40 min. JURA de-scaling tablets wich are specially designed for the de-scaling program of your IMPRESSA are available at your authorized dealer. Please note that machine defects or residues in the water cannot be excluded if you use inappropriate de-scaling solvents. If the IMPRESSA needs de-scaling, the corresponding message is displayed.
OPEN TAP Open the steam / hot water draw-off tap (14) (Fig. 13). DE-SCALING CLOSE TAP After you have closed the steam / hot water draw off tap (14), the following message is displayed DE-SCALING EMPTY TRAY Empty the tray NO – TRAY Insert the tray again. PRESS RINSE Press the maintenance key (7). RINSING READY The de-scaling operation was completed successfully. 19.
21. Messages Cause Remedy Water tank is empty. Refill water Float defective Rinse or de-scale water tank Bean tank is empty. Refill beans Although you have refilled beans, the message still appears. Draw off a cup of coffee. The message will disappear only after you have drawn off a cup of coffee Coffee grounds container full Empty coffee grounds container Tray reinstalled too early after emptying Wait 10 sec.
22.
23. Legal information 24. Technical Data These operating instructions contain all the information required for using, operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance. These operating instructions cannot cover any conceivable application. The machine was designed for private household use.
