USER’S MANUAL Xemio-657 MP3/MP4 Media Player with 4GB memory 1
For information and support: www.lenco.
Cautions Do not place naked flames, such as lighted candles on or near the product. Do not place objects filled with liquids, such as vases on or near the product. Do not use or store this product in a place where it is subject to direct sunlight, heat, excessive dust or vibration. Do not use this product with wet hands. Do not clean this product with water or other liquids. Do not block or cover the slots and holes in the product.
Do not expose to dripping or splashing. No naked flame sources, such as lighted candles, should be placed on the product. Ventilation should not be impeded by covering ventilation openings with items such as newspapers, table cloths, curtains and the like. Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty.
G: Prolonged exposure to loud sounds from personal music players may lead to temporary or permanent hearing loss. WARNIN G: 1.
Item Description 1 TFT LCD Display 2 Button (On / Off, Play / Pause) 3 Button (Previous / Fast-Rewind) 4 Button (Next / Fast-Forward) 5 M Button (Menu) 6 Button (Previous Menu / Exit) 7 Micro USB Port (PC Connection / Charge) 8 Microphone Position (mono, inside USB port) 9 Micro SD Memory Card Slot 10 Earphone Output Jack (3.5mm Stereo) 11 Button (Volume Down) 12 Button (Volume Up) 2. About Player Battery Player has an internal, non–user-replaceable battery.
Battery is in full Note: Player may continue use battery power after it’s been turned off. For maintain the battery life and performance, if unit isn’t used for a while, the battery need to be recharged, recharging the battery at least once per month. a. Charging the Battery: You can charge the player battery in two ways: Connect player to your computer. Or, Use the USB power charger. (not included) b.
In Charging Important: The battery does not charge when your computer is in sleep. The USB port on most keyboards does not provide enough power to charge the player. Connect player to a USB 2.0 port on your computer only to prevent charge problem. 3. Connecting and Disconnecting Player You can connect the player with your computer to transfer those media files and recorded voice memos when necessary, and to charge the battery.
a. To Connecting Player To connect player to your computer, plug the connector of USB Cable into a USB port on your computer, and connect the other end to player, then the “Connect” screen appear for view. Now the player is ready for media files transfer with your computer and the battery is charging. You can transfer the media files by using the computer mouse use drag and place, or copy and paste, in between the player and your computer. Disconnect it when you’re done. b.
If you’re using a Mac, you can also eject player by dragging the player icon on the desktop to the Trash. Disconnect the USB cable from the player and computer, simply remove it. If you accidentally disconnect player without ejecting it, reconnect it to your computer and sync again. However, some media file may loss. 4. Getting Start the Player Turn ON / OFF the player and use of Main Menu.
5. Use Setup Menu You might need to set date & time or change some default setting as you desired in setup sub menu before you start to use the player. To go into setup menu, from main menu, choose “Setup” by use / button and then press button, a “Setting” menu appears to use. You can go back to previous menu by press the setup menu. Or, press and hold the menu.
(Menu Page 1) (Menu Page 2) a. To Setup “System time” (Date & Time): Choose “System time” by using / button and then press button, a date & time setting screen appears to use. Press “ ” button, the year is highlighted then adjusting to current year by pressing the methods by “ / / ” and button. And repeating the adjusting / button again for finished those items; Month, Date, Hour, Minute and seconds setting adjustment.
when every time you turn ON the player. To change LCD backlight, choose “LCD set” > choose “Dark mode”, a level bar with number appear then chose “0 (always On) / 5 / 10 / 15 / 20 / 25 / 30 / 35 / 40 / 45 / 50 seconds” as you desired by using and / buttons. Choose “0” to prevent the LCD backlight from turning to off. (choosing this option decrease battery performance) c. To Change “Language” This player can use difference OSD languages.
50 / 60 / 70 / 80 / 90 / 100 / 110 / 120 minutes” as you want by using and / buttons. e. To View “Memory info” You can view about the memory status of player, such as the numbers of remaining memory space available and the percentage of memory have used. To view the status, choose “Memory info” by using and / buttons. An information screen, remaining memory space available and percentage of memory used, appear for view. To return to setup menu or main menu press hold button or press and button.
6. Use Music Menu You can use music player to playback with supported music file format of audio coding; WMA and MP3 are supported by the player. To open the music player in Main Menu: From main menu, choose “Music” by using / and button, a “Music Now Playing” screen appears to use. “Music Now Playing” Screen a. To Play / Pause Music In Music Now Playing screen, press Press button to pause the playing music. Press it again to resume. b.
Press button to play previous music. c. Use Fast-Forward or Fast-Backward Press and hold button to use fast-forward Press and hold button to use fast-backward. d. Adjust volume level In music playing, press / buttons to adjust volume levels to Up / Down. Wait for 6 – 8 seconds or press button to return to music now playing screen.
Playing the music with lyrics, and then press and hold M button to enter the lyric display mode and the lyrics is displaying and moving up accordingly with the playing music. Press M button to cancel the lyrics display and go back to Music Now Play screen if you want. 7. Use Music Submenu in Music Stop Mode You might need to selecting folders for music play and delete music files. To do this: a.
and then choose which music file that you want to delete by using / and buttons. Once file is selected, press button and choose Yes to confirm or No to cancel. c. Delete All In Music Submenu screen, choose “Delete all” then selects “Yes / No” by using / button. One “YES” or “NO” appear then press button to confirm.
Repeat folder / Repeat all / Random ” as you desired by using and / buttons. b. To Change Equalizer In music playing mode, press M button, a Music Submenu appear, the choose “Equalizer”, then choose “Natural / Rock / Pop / Classic / Soft / Jazz / DBB” as you desired. c. Exit Select Exit to back to music now playing screen. 9. Use Movie Menu a. To Play Movie From Main Menu, choose “Movie” by using / and button, a “Movie Now Playing” screen appears to use.
Press and hold button to play fast-backward. d. Adjust Volume Level In movie playing, press / buttons to adjust volume levels to Up / Down. For hearing protection; a beep warning will be heard from earphone, when every time you increase the volume level and reach to the default setting level which may exceed 85dB. Press M button to accept the warning and press 10. button to increase the volume level.
b. Delete File In movie submenu screen, choose “Delete file” a file list menu appear, and then choose which movie file that you want to delete by using / buttons. Once file is selected, press button and choose “Yes” to confirm or “No” to cancel. c. Delete All In movie submenu screen, choose “Delete all” then selects “Yes / No” by using / button. One “YES” or “NO” appear then press button to confirm.
11. Convert Video files into AMV This tool can be used to transform those video files into AMV files on the computer before upload them to your player. To install this video convert tool to your computer, open a folder named “UTILITIES > Video Conversion Software” which stored in your player’s internal memory or stored in a provided CD. (Download it onto your computer for copy and installation) Select “Setup” to start the install program, the software will automatically install to your computer.
Noted: This program is used to convert video files into AMV format, currently only AMV format is supported by this player. Then click to choose the folder where to save the AMV files, and then click to select the folder where the original files are. The original file will show in the file window once selected.
Move the mouse arrow and left click mouse on the unconverted source files to select with highlight in the file window, then the icon will be highlighted into icon. Now click this dialog box will be shown. Now click this icon and a dialog box will be shown.
Make sure Video type is “AMV”, Screen width and height is “160x120” selected. Video convert and Image quality should be “Normal” and “High” as defaulted. Click “OK” to confirm the setting. Now click to start converting.
After conversion, the AMV files will play automatically for preview. And now, the converted AMV file is ready to transfer, you can simply copy and place those converted AMV files to the media player. Note: Only pixels in 160x120 can be supported by this player.
12. Use Record Menu You can use the player as a Voice Recorder and recording voice memos using the built-in microphone. a. To Start Recording Voice Memo From main menu, choose “Record” by using / and buttons, a “Now Recording” screen appear to use. “Now Recording” Screen b. To Start / Pause Recording Press button to start the recording and the recording time is running. Press button to pause the recording and recording time will stop and flashing.
c. To Save and Stop Recording File Press or press and hold button, the recorded file will save into memory and ready for next recording. Press and hold button, the recorded file will save into memory and to exit. 13. Use Record Submenu (in Stop Mode) You might need to change the folder locations which want to store the record file and / or change record quality to better compression values. In Now Recording screen at stop mode, press M button, a “Record Sub-menu appear to use. a.
In record submenu, choose “Record type”, then choose “32K BPS / 64K BPS / 128K BPS / 256K BPS” values as you desired by using 14. / and buttons. Use Voice Menu For playback and manage the recorded voice memos file. From main menu, choose “Voice” menu by using / and buttons, a “Voice Now Playing” screen appear to use. “Voice Now Playing” Screen a. To Play and Pause Recorded Voice Memos In Voice Now Playing screen, press recorded file. Press button to pause the playing file.
b. To Play Previous or Next File Press button to play next file. Press button to play previous file. c. To Fast-Forward or Fast-Backward Press and hold buttons to use fast-forward Press and hold button to use fast-backward. d. Adjust volume level In music playing , press screen appears, then press / button, a change volume control / buttons to adjust volume levels to up / down. Wait for 6 – 8 seconds or press button to return to music now playing screen. 15.
In Voice submenu screen, choose “Local folder” a list menu appear, and then select folder and / or choose a voice file by using / and button. It will go back to music now playing screen once a music file is selected. Then press button to play. b. Delete File In voice submenu screen, choose “Delete file” a list menu appear, and then choose which voice file that you want to delete by using / and buttons. Once file is selected, press button and choose Yes to confirm or No to cancel. c.
16. Use Voice Sub-menu in Playing Mode You might need to do some changes for music playing, such as repeat, EQ settings for music files… etc. To change setting: a. Repeat In voice playing mode, press M button, a Music Sub-menu appear, then choose “Repeat”, then choose “Normal / Repeat one / Folder / Repeat folder / Repeat all / Random ” as you desired by using and / buttons. b. Exit Select Exit to back to music now playing screen. Note: Press and hold the 17.
selection. To change previous / next photo, press Press and hold 18. / button. button to back to main menu. Use Photo Submenu in List Screen You might need to change some setting for photo browse. To change setting: a. Local Folder In list menu, press M button to call up the photo submenu. In photo submenu, choose “Local folder” a list menu appear, and then choose folder and file to browse by using / and M button. Once photo file is selected, press button to play. b.
time gap to playing the photo files one by one automatically. c. Delete file In photo submenu, choose “Delete file” a list menu appear, and then choose which photo file that you want to delete by using / button. Once file is selected, press button and choose Yes to confirm or No to cancel. d. Delete All In photo submenu, choose “Delete all” then selects “Yes / No” by using / button. One “YES” or “NO” appear then press button to confirm.
a. To open eBook From main menu, choose “eBook” by using / and buttons. A list menu appears to use. Choose a file which you want to read by using then press button, and button to play. Press button to change next page, Press button to go back to previous page, Back to list menu screen, press button. Go back to main menu, press and hold 20. / button. Us eBook Submenu in list menu screen You might need to change some setting for eBook reading. To change setting: a.
“Manual play”. You need to use / button to change next / previous page for reading when Manual Play is selected. Or, Choose “Auto play”, a setting menu appears, then choose “1 / 2 / 3 / 4 / 5 / 5 / 6 / 7 / 8 / 9 / 10 second(s)” as you desired by using and / buttons. The Page Flip function is activated as your selected time gap to playing. c. Delete file In eBook Submenu, choose “Delete file” a list menu appear, and then choose which eBook file that you want to delete by using / button.
Select Exit for back to eBook list menu screen. 21. Us eBook Submenu in Playing Mode You might need to add, select and delete some bookmark when you reading, to do this: a. Bookmark Select In eBook playing mode, choose “Bookmark select” by using and / button. Choose a stored bookmark which you want to call and then press M button to play. b.
reading page automatically. d. Exit Select Exit for back to eBook list menu screen. 22. Use Memory Card Slot This player allows you to play those support media files from your memory card (T-Flash). Also it will increase the mobile hard disk memory capacity of the player if you use this option. a. To Play From Memory Card: Turn Off the player. Now insert your Micro SD memory card into the memory card slot on side of player.
There have a game name “Snake”. Control the snake move up, down, left and right to eat the food (dot) which will exist somewhere on TFT screen. The snake’s body will get longer at every eats for food, but don’t let the snake hit the walls and hit the snake body. To play game, from Main menu, choose “Game” menu, then choose a game to play. Control KEY instruction; Press: = left, = right, M = Up, = Down, = Pause. Press and hold M button to exit the game. 24.
Important: Do not reset the device if it is proper working. 25. Trouble Shooting Unit cannot turn ON * Check whether Power is slide to ON. * Check battery is it charged with enough energy. No sound is heard * Check whether Volume is set “0” and from headphone. connect the headphone plugs firmly. * Check whether the headphone plug is dirty. * Corrupted MP3 may make a static noise and the sound may cut off. Make sure that the music files are not corrupted.
26. Specification Dimension 85mm (H) x 41.5 mm (W) x 9.0mm (D) Weight 25.5g LCD 1.8 inches, Resolution (RGB) 128 x 160 PC connection USB 2.0 (High Speed) Earphone Impedance 32 Ohm Internal Memory See carton or giftbox Memory Card Slot Micro SD Card (support up to 16GB and possible for 32GB) Battery Lithium 3.7V, 170mAh Max.
256kbps Picture Format JPEG / BMP eBook Format TXT Operating 0 to 40℃ Temperature Operating System Window 2000/XP/Vista/Win7, Mac 9.2 or Higher 27. Disclaimer Updates to Firmware and/or hardware components are made regularly. Therefore some of the instruction, specifications and pictures in this documentation may differ slightly from your particular situation. All items described in this guide for illustration purposes only and may not apply to particular situation.
Germany 0900-1520530 (Local charges) The Netherlands 0900-23553626 (Local charges + 1ct p/min) Belgium 02-6200115 (Local charges) France 03-81484280 (Local charges) The helpdesk is accessible from Monday till Friday from 9 AM till 6 PM. When contacting Lenco, you will always be asked for the model and serial number of your product. The serial number can be found on the back of the device.
Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires. This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided. 29. CE marking Products with the CE marking comply with the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community. The declaration of conformity may be consulted at http://www.lenco.
laws of requirement for disposal of electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).
