55.5cm (22”) Full HD LED TV WITH DVB-S2,H.264,DVB-T/C AND CI Model No.: LED-2217 For information and support, www.lenco.
Contents SAFETY INFORMATION .............................................................................................................3 Headphone Warning ....................................................................................................................................................... 4 Where to install .............................................................................................................................................................. 4 LED Screen.............
LOCK menu................................................................................................................................................................... 25 Multimedia Operation.............................................................................................................26 Basic Operation ............................................................................................................................................................ 26 1. Photo ..................
Introduction Thank you for purchasing this LED TV which has been designed and manufactured to give you many years of trouble free service. You may already be familiar with using a similar product but please take time to read these instructions which have been written to ensure you get the very best from your purchase. HDMI terface) is the next generation of digital interface.
This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against careless use and the dangers connected with such use. Although this appliance has been carefully manufactured and rigorously checked prior leaving the factory, as with all electrical appliances it is possible for problems to develop.
Unit and Accessories Getting Started Front view MUTE POWER REC LIST CH/LIST SUBTITLE REPEAT REC DISPLAY TV/AV OK MENU 1 EXIT 2 3 5 6 7 9 0 VOL 4 8 FAV PICTURE EPG SOUND SLEEP INPUT CH SCREEN TV/TXT HOLD CANCEL REVEAL SIZE SUBPAGE MENU NICAM/A2 INDEX CH+ CH- TV set Remote Control Batteries for Remote Control VOL+ VOLPOWER Remote Control window Converter cable for AV and YPbPr video 1). (IR) Infrared Receiver: Receives IR signals from the remote control.
Remote control The remote control is using Infra-Red(IR). Point it towards the front of the TV. The remote control may not work correctly if it is operated out of range or out of angle. POWER MUTE REC LIST CH/LIST SUBTITLE REPEAT REC DISPLAY INPUT POWER: Turn the TV on/standby. MUTE: Press to mute the sound, press again or press VOL+ to unmute. REC LIST: Record List. CH/LIST: Display the programs list. SUBTITLE: Turn on/off the subtitle display in DTV mode REP: Repeat playing the title or chapter.
Remote control (continued) POWER MUTE REC LIST CH/LIST SUBTITLE REPEAT REC DISPLAY INPUT OK MENU EXIT 1 2 3 4 5 6 7 8 9 0 VOL FAV PICTURE EPG SOUND SLEEP CH SCREEN TV/TXT HOLD CANCEL REVEAL SIZE SUBPAGE NICAM/A2 INDEX CH / : Scan through channels. VOL / : Adjust the volume. PICTURE: Select the picture mode. EPG: To show the Electronic Program Guide during no-menu state only in DTV mode. SOUND: Select the sound mode. SLEEP: Standby timer. SCREEN: Turn on/off the screen.
Installing Batteries in the Remote Control Aerial connection 1. Remove the battery compartment cover at the rear of the remote control by pushing the retaining clip forward and pulling up. 2. Install the supplied batteries, ensuring the polarity matches what is shown in the battery compartment. 3. Replace the battery compartment cover.
Connecting external devices (continued) Output t DVB-S2 Common Int fac Sat t Output t POWER USB HDMI SCART PC-IN VGA MINI YPbPr MINI AV Converter cable audio USB device Satelliten Receiver oder Blue-Ray DVD 9
Connecting external devices (continued) VGA, HDMI PC Connection Name Function Description POWER Connect to power supply HDMI Connect to the HDMI output of your DVD or Satellite Box Use a PC-VGA cable (not supplied) to connect the TV to your PC. You can also use an HDMI cable to connect to your PC (if your PC Graphic card supports HDMI). When the HDMI cable is used, the PC audio cable is no longer required. If you use the HDMI to DVI cable, you will need to use the PC audio cable.
Connecting Video camera and Video recorder Connecting an audio system Video camera You can supply the TV sound to the stereo system (A) with the Scart socket. Use a special Scart cable SCART to RCA. (Please consult y structions for details). If you have a surr coder (B) Use the Scart cable or the special Scart cable Scart to RCA. Connect the AV cable to the TV and to the video camera. Turn on both video camera and the TV. Select AV/CVBS source You can now see the playback picture from the video camera.
COAX Connection SCART Connection TV Back DVB-S2 POWER USB HDMI SCART Coax Cable PC-IN Sc D Connect t on the TV. evice to the COAX output jack VGA MINI YPbPr MINI AV cable VCR Back D VCR Connect the SCART connect to the ext tem and the SCART connect V. The SCART lead ope at connection. If the tv does not select the SCART input automatically, select SCART using the SOURCE button on the emote cont v.
AV Connection TV Back USB HDMI SCART PC-IN VGA MINI YPbPr MINI AV Audio and video cable (RCA) Mini audio and video transfer cable DVD or VCR back DVD or VCR Connect the VIDEO and AUDIO output jack of the DVD or VCR to the VIDEO jacks on the TV set using the RCA cable. Match the jack colors: Video is yellow, Audio left is white, and Audio right is red. Select the AV input source via the SOURCE button on the remote control.
Common Interface Slot Auto installation setup USING YOUR COMMON INTERFACE SLOT Power On / Off the LED TV Common Interface To turn on the LED TV The Common Interface (CI) slot is designed to accept the Conditional Access Module (CAM) and Smart Card in order to view the pay TV programmes and additional services. Contact your Pay Per View TV service provider to get more information about the modules and subscriptions.
INSTALLATION MENU OPERATION DTV will install a Digital Terrestrial Television service (DVBT) INSTALLATION GUIDE When powering up f Will appear on screen. Choose the language using OK ATV will install an Analogue Television cable service rst time the Installation Guide During the channel search this menu is displayed showing the progress. buttons and then press Choose the service to install using the then press ok. buttons and You will now see the quick-start menu.
TV SETTINGS Menu SATELLITE / DISH SETTINGS Input Source DTV CADTV SATELLITE ATV SCART YPbPr PC HDMI AV USB DIGITAL CABLE (DVBC) SETTINGS All the above installations can also be accessed through the Main Menu system. In the TV Settings menu. To access the correct service you need the TV to be in the correct mode, ATV, DTV, cable or Satellite. Select the mode either from the handset or from the source menu.
Unlike QUICKSTART the satellite search will search the whole satellite for channels and will not be instant. You can manually tune CADTV channels in the TV SETTINGS menu. Also the channels will appear in the order on the satellite and not the pre-set order. Frequency Select Frequency using the buttons. Symbol (ks/s) Select the Symbol (ks/s) using the buttons. QAM Type Select the QAM Type using the buttons ATV Manual Tuning You can manually tune ATV channels in the TV SETTINGS menu.
PROGRAMME EDIT Dish Setup Use up/down keys to select program edit. Press OK or Right button to enter the menu. Use up/down buttons to navigate through the menu 1. If you do not hav xed dish aligned to Astra 19.2E ted with universal LNB you will need to use this section. ed Dish aligned to a different Satellite 2. If you hav or with a different LNB you will need to use this section. 3. If you have a motorised Dish with a DiSEqC rotator and wish to tune more than one satellite you will need this section.
Press button to navigate to LNB section of the menu. Select the LNB type and settings for your second LNB and switch settings. Press the blue Key to search the satellite channels. A full description of the advanced Dish set up for multiple satellites using DiSEqC switches and DiSEqC positioner follows. This should only be attempted by experience users. The Dish set up main menu page displays the main interface.
Transponder List Add Transponder The list shows the transponders for the selected satellite. Press RED button to enter the add transponder menu. No. Can not be manually edited. Frequency: Set the downlink frequency. Symbol (ks/s): Set the Symbol Rate. Polarity: (H/V) Dish Parameter description LNB Type: LNB Frequency Edit Transponder menu Press GREEN button to enter Transponder edit menu. No. This is the list placing number. Nr. cannot be manually edited Frequency: Set the downlink frequency.
Highlight the LNB Type , and use the to enter submenu then you c buttons and Ok rameters. KHz: The level of the LO switch / DS switch ( Require the user to have installed 22KHzSatellite signal switch). to select Auto/On/Off. Press Auto: Automatically issued 22 KHz pulse signal to control switching. On/Off: Manual control switch. Tone burst: Double Single Switch (Require users to install Tone burst switch), Press to select Burst A/Burst B/None. Burst A /Burst B: Manually switch the satellite A/B. DiSEqC1.
Press RED button to enter “Set Limit” and Mot as “DiSEqC1.3” “Set Limit’ menu same. Move Continue: Control of the east or the west continued to turn the polar axis to the desired position. Move Step: Control of the east or wes axis step rotation. xed polar Set West Limit: The current position is set to the maximum point of the west. Press GREEN button to enter Set Location menu. Set East Limit: The current position is set to the maximum point of the east. Goto Reference: Back to the default values.
Move Auto: East or west of Automatic Control continued to turn the polar axis to the desired position. MENU SETTINGS Move Continue: Manual control of the east or the west continued to turn the polar axis to the desired position. Picture menu Move Step: Control of the east or wes axis step rotation. xed polar Store Position: Save the current rotation angle of polar axis. Goto Position: Control the polar angle automatically to the previously saved.
SOUND menu On Time: Press OK button to enter the submenu, you could set the time when the TV set will be turned on automatically, you could also set the frequency, volume and program. Sleep Timer: Allows you to setup the sleep timer among: 10min, 20min, 30min, 60min, 90min, 120min,180min, 240min and off. Auto Sleep: Turn on/off the auto standby function. Time Zone: Allows you to select the time zone. OPTIONS menu Sound Mode: Allows you to select among: Standard, Music, Movie, Sports and User.
LOCK menu The password must be entered to access the Lock Menu. The default password is 0000. Once inside the menu you can change the password to your own choice. Channel lock is used to block selected Channels Parental Guidance blocks programmes according to their parental level.
7.
Multimedia Operation Basic Operation 1). Press the INPUT button on the remote control to display the input source menu, select USB source by the / buttons, and press OK button to enter the Multimedia menu seen below. Input Source DTV CADTV SATELLITE ATV SCART YPbPr PC HDMI AV USB Select 2). Insert USB device, you will find the name of the device display on the screen.
Multimedia Operation 1. Photo Play the photo Press / button to select the option on the table, and press OK button to change. Repeat: Select the repeat mode from Repeat All, Repeat 1, Repeat None. Music: Play/pause the music program (you can only play or pause the music you have programed). Playlist: Display the playlist on the screen, and you can select the photo by / button, and press OK button to program. Press / button to return to the options table. Info: Display the information of the photo.
Multimedia Operation 3. Movie Play the movie GOTO Time Press / button to select the option on the table, and press OK button to change. Repeat: Select the repeat mode from Repeat All, Repeat 1, Repeat None. Set A-B: Select and play the preferable paragraph of the program by seting A and B at the beginning and end, and there will be a sign on the left screen, press OK button again to cancel. Playlist: Display the playlist on the screen. Info: Display the information of the movie.
Recording Operation PVR settings Press the MENU button, and select CHANNEL menu. Recording Timer 1). Recorded List Display the recorded list Recorded list: Display the Recorder List menu, and changed the mode of program. INFO: Display the information of the program you recorded. RED button: Delete the program you select. 2). Recording Timer Set the recording timer The TV will record the program automatically according to your settings. TITLE: Display the name of the recording program.
Recording Operation 3). Schedule List Display the recorder shedule Note: a. Could’t add shedules which have existent on the list; b. Could’t add shedules when the list is full, you have to delete some schedules; c. You could delete a schedules by RED button on the remote control. 4). PVR File System Setup the PVR File system before you start recording. Select Disk: Select the device for the Record files. Check PVR File System USB Disk: Display the USB state.
Recording Operation 5) Record Start When you finish the settings above, you could start recording by select Start Recording in the menu and press OK button in DTV and DVBS mode. (You can also start recording by press the on the remote control) Record buttons Recording: Press to enter the recording mode. PAUSE: Press to enter the timeshift mode. Recording list: Press to display the recording list. Stop: Press to stop recording.
TROUBLE SHOOTING GUIDE To assist in locating possible faults use the help guide below. SYMPTOM SOLUTION No Picture, no sound Check that the TV is correctly plugged in. Check that the TV is connected to a suitable power source. Check the electrical supply is turned on. No Picture Ensure that the TV is powered on. Check that the cables ar ted securely. Ensure the aerial and/or external sources are connected. Press the SOURCE button to change the source. Turn the TV on or off.
I LENCO II LED-2217 27 55,5 39 22
