English IPD-4100/2 Series iPod Speaker Dock with FM radio User Guide For information and support, www.lenco.
Thank you for choosing this Lenco iPod Speaker Dock with FM Radio. Not only can it receive radio stations, but you can also listen to your favourite tracks on your iPod and charge it up. It’s really simple to use; you can fully operate your iPod from the control panel on the top or from the remote control, and even connect another auxiliary device to it. Throughout this User Guide, the iPod Speaker Dock with FM Radio will be referred to as the Speaker Dock.
Power Adapter 2
TOP DOC POWER MEMORY CARD DOWN ARRO W/ FWD TUNE UP ARROW/RWD SLEEP/CLOCK ALARM EQ MODE 3 MEM
ANT MEMORY BATTERY Compartment SPEAKER Port IPD-4100/2 FM: 87.5MHz - 108MHz INPUT: DC 15V 2.0A IMPEDANCE: 4channel / OUTPUT POWER:10W * 2+20W MAX.
1.Setting up the iPod Speaker Dock Insert the Mains Plug into a suitable wall socket and turn the socket on. Press the STANDBY button to turn the Speaker Dock on. 2.Using the Remote Control The Remote Control can be used to operate the Speaker Dock. Before using the Remote Control, the Safety Tab should be removed. Simply pull out the Safety Tab from the remote control, as shown below.
desired buttons. DON’T FORGET! When replacing the battery make sure that you use the same size and type. 3. iPod Docking Any iPod can be connected to the Speaker Dock to allow all your songs to be played through the speakers. To connect an iPod to the Speaker Dock, select the compatible adaptor from one of the 7 iPod Adaptors supplied. The iPod Adaptors have markings on the bottom which clearly identify which iPod they should be used with.
and then insert your iPod into the Adaptor. DON’T FORGET! Your iPod will charge while docked when the Speaker Dock is in Standby mode. Press the STANDBY button. Press the MODE button repeatedly until iPod is displayed on the LCD Display. To start playback, press the PLAY/PAUSE button. 4. Connecting to External Devices Your Speaker Dock can be connected to a number of external devices using the supplied 3.5 mm Stereo cable (supplied) or an RCA cable (not supplied). Switching On 1.
• Jazz • Pop • Rock • Classic • Bass 1.Press the EQ button to select the setting which sounds best. Modes The iPod Speaker Dock has three modes of operation. These are: • iPod • Tuner • Aux Brightness 1.Press the BRIGHTNESS button on the remote control repeatedly to cycle through the 4 display brightness settings. Memory Cards You can play MP3 files stored on SD or MMC memory cards by inserting them into the Memory Card Slot on the top of the Speaker Dock.
Menu Navigation You can access the menu system of your iPod using the Remote Control. 1.To access the iPod menu system, press the MENU button. 2.Use the UP and DOWN ARROW buttons to highlight the menu options. 3.Use the OK button to select a menu option. Radio Tuning to a radio station 1.Press the STANDBY button. 2.Press the MODE button repeatedly until Tuner is shown on the LCD Display. 3.Press and hold either the FWD or RWD buttons to search for a station. 4.
DON’T FORGET! You may need to reposition the Speaker Dock to get the best reception. Storing a radio station using the remote control 1.Tune to a radio station as described above. 2.Press the MEM button. MEM and a number will be shown on the LCD Display. 3.Press the UP or DOWN ARROW buttons to select the number you want to store the radio station against. 4.Press the MEM button again to store the station. 5.Repeat this procedure to store other radio stations.
Speaker Dock. 3.Insert a button cell (type CR2032), ensuring the correct polarity is observed. 4.Close the Memory Battery Compartment. Setting the clock 1.Make sure the Speaker Dock is powered on before setting the clock. 2.Press and hold the SLEEP/CLOCK button. SET will be shown in the LCD Display next to the clock time. 3.Press the UP or DOWN ARROW buttons to change the minutes. 4.Rotate the VOLUME CONTROL to change the hour. 5.Press the SLEEP/CLOCK button to confirm the new clock time. 6.
The Speaker Dock can be reset to return to the factory default settings. 1.Switch off the Speaker Dock and remove the plug from the wall socket. 2.To reset the Speaker Dock, remove the Backup Battery from the Memory Battery Compartment as described in the previous sections. 3.Replace the Backup Battery after approximately 2 minutes. The Speaker Dock will be returned to the factory default settings.
Problem Possible Cause What to do Radio sound distorted. 1.The station is not tuned in. 1.Fine tune the station. 2.There is a poor signal in the 2.Reposition area. Dock. No radio sound. the Speaker 1.The Speaker Dock is not in 1.Press the MODE button until tuner mode. Tuner is selected. 2.The volume has been muted 2. Adjust the volume level. or is on the minimum setting. The iPod will not play 1.The Speaker Dock is not in 1.Press the MODE button until iPod mode. iPod is selected. 2.
Sound levels Your hearing is very important to you and to us, so please take care when using this Speaker Dock. It is strongly recommended that you follow the listed guidelines in order to prevent possible damage or loss of hearing. Establish a safe sound level Over time your hearing will adapt to continuous loud sounds and will give the impression that the volume has in fact been reduced. What seems normal to you may in fact be harmful.
Electrical Information This Speaker Dock is fitted with a BS1363/A 13 amp plug. If it is not suitable for your supply sockets it must be removed and replaced with an appropriate plug. If the plug becomes damaged and/or needs to be replaced please follow the wiring instructions below. The plug removed must be disposed of immediately. It must not be plugged into a supply socket as this will be an electrical hazard. If the fuse needs to be replaced it must be of the same rating and ASTA approved to BS1362.
• The guarantee is in addition to, and does not diminish, your statutory or legal rights.
